Upgrade to K7N2 DELTA-ILSR help

Thinking of purchaseing the K7N2 DELTA-ILSR board and would like some help verifying the hardware i have not having any problem with this mobo.
AMD|2800/333 ATHLON XP BARTON
MEM - DDR Corsair dual 512MB X2 KIT|VS1GBKIT333
Soundblaster 5.1 Platinum
Liteon 52x32x52 r\rw
80GB|SEAGATE ST380011A 7200
60GB|SEAGATE ST360015A 7200
PSU- Super-Flower Silent TT aluminum 450W ATX power supplyTTGI TT-450SS (450W). AC Input: 100~120Vac/200~240Vac, 10/6A, 60/50Hz. DC Output: +3.3V~28.0A, +5V~42.0A, +12V~18.0A. +5Vsb~3.0A, -5V~0.5A, -12V~0.8a). MAX OUTPUT POWER: 450W. Cooling: Air convention by +12V DC fan. 10 IDE connectors, 2 floppy connectors, +12V power connector, Aux power connector
CPU FAN - OCZ GLADIATOR 3 Socket A/462 up to Athlon XP 3200+. Single-piece pure copper construction. Dimensions: 60x60x30mm. FAN: 60x60x25. Medium-speed. Or: 60x60x25 Quiet. High-speed. Voltage: 12 Volt. Ball bearing fan
Video Card - Chaintech VGA GF FX5700 SA5700 256M
It looks like a great board and i see some great reviews but also see alot of small issue with compadability. It looks like the 1st thing is to upgrade the bios, and hope i don't have any issue with my cable modem box (guess i could put my old network card back in and disable the mobo's built in net work if there is problems).
I don't do O\C so nothing to worry about there. My old board is an Epox and is max'd out with no future upgrade room, so that's why i'd like to upgrade.
Thanks for any help guys.
rider

rider45,
If you do not need the Break Out Box from the Platinum, I would go with the onboard nVidia SoundStorm. It sounds better than the old Live! and uses less CPU Cycles.
Take Care,
Richard

Similar Messages

  • MSI K7N2 Delta-ILSR Help Please.

    Hi all
    I have a MSI K7N2 Delta-ILSR motherboard that im putting together and I have a question.
    In the middle of the socket where the CPU sits is a small CPU thermal protection sensor, my question is that the sensor is higher than the socket and will be touching the CPU when it is inserted is this normal or should sensor be bent downward so not to be in direct contact with the CPU?
    I would not be asking this question if not for someone telling me not to put any external case sensor on the CPU direct only on the heat sink but in this case its built into the motherboard itself. Best to be safe than sorry I thought.
    Many thanks

    Hi Andy
    I too have just bought an MSI K7N2-ILSR. On mine the sensor is bent down so as not to contact the cpu. Was like this when I bought it so I would suggest that it is not supposed to touch processor

  • HELP me with my K7N2 delta ilsr

    Can anyone help me with this problem. I have just upgraded to MSI's K7N2 delta ilsr motherboard. Its all working quite well apart from the fact that the pc wont start up from cold....at all.
    When I start the pc from an off state, it runs up the fans and drives, but does not post.
    The diagnostic led pannel on the back of the pc shows that the cpu is faulty or not installed correctly.
    If I then press the reset button, the pc posts, and boots up just fine.
    It does this EVERY time I start up.
    I have tried re installing the cpu, which is an XP 2800+ 333 barton, but to no avail.
    I have asked a few questions on other forums, but I cant solve it.
    These are the suggestions so far.
    1. the psu (I have a Tsunami 400 atx psu) could not be giving out enough power on initial startup, but once the pc is running, it has enough to boot the pc from a reset.
    2. The mobo or the bios could be at fault. I have not flashed the bios, or upgraded it in any way from original, so is there an issue with the original bios on these boards, and 2800 barton chips??? Could it be a mobo fault? The pc runs fine once the machine is booted.? how do I test it?
    3. The cpu could be faulty? but would this not stop it running fuull stop?
    4. my ram. I have a single stick of OCZ 512mb pc3200 ddr, which I was told would make the pc fly. Not shure on that statement, but is this ram compatible?? could this be the problem?
    Im fairly new to the upgrade side of things, and I need some help with this one.
    Also, Id be really greatfull if some one could talk me through flashing my bios to the latest version, as the thought of doing this narks me a bit...I dont want to mess it up and get a dead pc...
    HELP

    +3.3v 14A
    +5v 28A
    +12v 16A
    +5vsb 2A
    -5v 0.5A
    -12v 0.8A
    Hope this helps, as my pc seems to be living with its case off a lot these days..haha

  • NEED HELP - K7N2 Delta ILSR

    I really need help. I recently bought my new moboard the K7N2 Delta ILSR and with it a GeForce FX 5600 256DDR, 512 DDD Ram PC3200, an 80Gb Seagate SATA HD, andi have a 2800+ AMD Athlon Xp Barton Core Cpu. The problem i get is that when i try to install Windows XP it says it cant find any hard drives. I saw the other thread that was like this but that one had about RAID so i thought i would ask again. I even tried it with Windows 98 which finds my hard drive and even installed once but after that i tried to upgrade to Windows Xp which didnt work, overwrited some of my Windows 98 files and so that didnt work either and when i try to install it again it gives me errors. PLS help im desperate to get my lan workin with my other PC. I havent changed any options in the bios and i dont know if i have to change anything to make sata work. I dont have a floppy disk either for the hd. I found it in the array thigy as well.  

    Windows will not find a SATA drive you have to tell it you have one bios will only find IDE drives.
    you must hit ctrl F when the screen comes up during boot and creat an array just follow the on screen promps.
    If you bought a OEM board and don't have the SATA Promise disk download it from MSI and a Manual too.
    Either a Raid 0 or Raid 1.
    It looks like you have only one drive so just tell it that and the array will work.
    Than go to your Bois and set Bois to boot from CD first SCSI secound.
    Now you can load your OS. When your OS starts to load it will flash a line across bottom of screen asking if you have SCSI hit F6 do so. The OS will keep loading but when its done it will ask for you 3.5 promise disk. Put it in and load the Fast Track 376 program.
    When you OS is finished loading it will again ask for this disk as the first time it just loads the drivers to memory the secound time to your HDD.
    Good Luck it a little confussing the first time as the programers think there talking to techs not people so use terms that sometimes don't make sense.

  • Someone plz help me with my k7n2 delta-ilsr

    Hey everyone,
            I just put my sytem togother and ran into a problem.  I got the system to boot up just fine.  It was not until I tried installing windows xp proffesional that  I ran into problems.  The installation process runs pretty smoothly, until the computer reboots to run windows for the first time.  After it reboots the windows logo appears and the after 2 seconds or so, a blue screen appears saying that windows was shut down to prevent any damage to my computer.  I have never encountered this problem before when I built other systems.  The screen suggests that I should check my HDD's for viruses or check to see if they are configured correctly.  The HDD's are SATA and I have them set up in RAID 0 mode and yeah I installed the RAID drivers during the installation process.  Thinking that I had made mistake setting up the SATA drives, tried installing windows using a regular IDE hard drive and it gave the same message.  I am stumped anybody have any ideas of what I might be doing wrong?  Any help would be appreciated .  My system specs are below.
    MSI k7n2 delta-ilsr mobo
    AMD 3000+ Athlon XP cpu (333 fsb)
    ATI Raedon 9000 ( I know it's crappy , I'm still saving up for the ATI all in wonder 9800 )
    x1 kingston 512mb pc3200 DIMM
    x2 maxtor 80gb maxtor hdd's
    x1 regular cd-rom drive
    x1 floppy drive
    420w raidmax psu
    (+3.3v = 26A, +5v = 32A, +12v=13A)

    Memory that comes with timing of 5 2 2 2 or 6 2 2 2 or usally winbond BH-5 memory chips. Ones with 5 3 2 2 or CH-5 winbond chips. The BH-5 chips overclock a little better than the CH-5. (Muskin uses BH-5 winbond in there black ram)
    Winbond is no longer making BH-5 chips but is going to make a limited run of them as demend is high for them.
    The first number shown here is the Traz and it controls the flush timing bench testing is showing that a higher number of 9, 10 or 11 or getting better bench results than the 6 or 5. Thats with Dual Channel memory.
    The timing you show probly should be something  like 8 3 3 3 or 8 3 3 2.5 unless it is there faster Dual channel ram.
    The timing numbers can also appear like this 2 2 2 5 the high number is the Traz either way.
    Look on your memory manufactor web site for the timing that if should run at also look at the voltage as this can make a big differance.

  • Kate needs HELP!!! MSI K7N2 Delta ILSR

    Guys...
    pls help me...
    I am assembling, yes I know I am a techi girl...., msik7n2 with radeon9600 and 2xCorsair Value Select 256Mb DDR 400Mhz PC3200 mem...(hence 512mb)
    I installed everything assembled it... booted and loaded fine for about 3 times...
    and suddenly....
    >power on
    >no video
    >no beeps
    >after checking hard nothing happens...
    >only thing I can tell is that the d bracket is indicating "memory section"
    ....d-bracket from MSI K7N2 Delta ILSR is 1,3,4 red and 2 green. Which is according the the manual "Memory Detection Test"-if the memory module is damaged or not installed properly.
    Why woudl a memory suddenly not work?
    I know I was adjusting bios for this and that....  
    I think just before this happened.. I adjusted something on agp setting... but what ahs that got to do with memory?
    COuld it be the mobo or memory or the video card???
    pls help....
    My email is [email protected]...
    please please help...
    and guys in MSI what is your expert opinion? mobo? or memory?
    Heeeeeeeeeeeeeeeellllp...
    thanks...
    Kate x

    hi and welcome to this forum.
    nice to se a girl here for a change
    clear cmos jumper jbat1.
    also try safe mode jumper j10 ans j11.
    also try to reseat memory and dont trust the dbracket to 100%.
    it can show wrong sometimes.
    Quote
    COuld it be the mobo or memory or the video card???
    when you got it running then run http://www.memtest86.com to check memory,
    also what psu do you have ?
    post max amps on 3.3v 5v and 12v rails.
    minimum is 28 35 16.recommended is higher.

  • MSI K7N2 Delta-ILSR Dead? Help!

    Hey all,
    Well, the other day I was on my computer playing a game when my mobo fan started making an odd noise (as if switching rpm), so I took off the side of my case and took a look inside. Everything seemed to be functioning properly, then I switched my cpu fan speed via the pci slot speed control. As I switched from High-Medium-Low, I noticed that the fan actually slowed to the point where I could see the blades spinning, at least for a second or so. I found that rather odd, seeing as how I've never seen a fan (especially a cpu fan) slow to the point that I could see the blades spin. Anyway, a couple of hours later, I shut down and went to sleep.
    The next day I had my comp on for about maybe 30mins to an hour or so when suddenly I heard an alarm from the computer speaker, so I was like, ":censored:?" since I had never heard it before. It was evidently the temperature warning, which I had set to 70C. So I shut down within 15 seconds and opened up the side of my case.
    I noticed that the cpu fan wasn't moving at all (usually I'd open the case in time to see the spin-down). So I turned the computer back on and the fan didn't budge, so I immediately powered down, assuming that the CPU Fan had died. Later on, I hooked the fan itself up to a free power cord in my sister's computer and booted up, along with the speed controller, flipping from medium to high to low without any problems.
    I then did screwed the fan back to the heatsink in my comp and booted up. I went into the bios an noticed that the rpm was 8k, which is way too high for my fan (normally 5k). So i began switching from high, medium, to low once again, then I saw that the rpm reader in the bios went to 0. So I looked back in the side of my case and saw that the cpu fan was once again dead. At this point I concluded that it was the fan and was about to order the Volcano 12.
    A day later I placed the fan inside my sister's computer on a free cord, yet again, and yet again, it worked fine.
    I once again put it in my computer to test and this time it worked fine, even while switching between speeds. Unfortunately, I then noticed that the mobo fan was not moving, then began to move.
    Well, I'm guessing now that it's simply the motherboard that has a short, since both the motherboard fan as well as the cpu fan have randomly been dying the past few days. The motherboard fan; however, has switched rpm many times in the past from 5k to 3k.
    It could also be a PSU problem, but I have Antec 400watt psu and it's been working fine for the past 2 years, so I doubt it. I've had the motherboard for a little over a year. I upgraded my cpu from 2200+ to 3000+ in July. That's also when I bought the cpu fan. The motherboard fan began fluctuating in rpm noticeably back in April or May of this year.
    Yesterday, I used the computer again and had it on for about 2 hours or so and I had speedfan monitoring the temps and the rpm. The temps stayed relatively stable: 48 cpu, 44 mobo.
    But alas, the RPMs were totally [blame me for the swear filter] up. At one point, both the mobo and cpu fan speeds were reading 0, even though both continued to spin within the case and the temps remained the same. Then after 30mins or so, they cpu fan began reading again at 40,000-42,000rpm, which is obviously incorrect, seeing as the fan is rated for around 5k. I got/get the same readings in the bios, both fans reading at 0rpm as they continue to physically spin.
    Also, during a number of times that I've started up the comp within the past few days, the motherboard northbridge fan wasn't spinning at all and didn't begin to until a few minutes into my windows session.
    Also, I took out the NB fan and noticed a slight crack in the back of it.
    I was considering simply just buying the Volcano 12 and the MSI K7N2 Delta2 Platinum rather than RMAing the mobo. Then perhaps an Antec 550W psu, if necessary.
    Any ideas what I should replace and in which order? And has anybody else encountered any similar problems with this mobo (at least with the mobo rpm, which has been a prob for about 6months on and off)?
    I bought the mobo along with a 2200+ in July of 2003. I upgraded the ram from 256 to 512 in April 2004 (which is around the time I started hearing rpm probs with the mobo fan) and I upgraded the cpu in July of 2004
    Many Thanks!  
    My Specs are as follows:
    Windows XP Professional SP1
    Antec SX1040B2 File Server Case
    400watt Antec PSU
    MSI K7N2 Delta-ILSR
    AMD Athlon XP 3000+ (2.17GHz)
    Thermaltake TR2 M2 HSF
    Kingston 256MB of PC2700 DDR-333MHz RAM
    Generic 256MB of PC2700 DDR-333MHz RAM
    ATI All-In-Wonder 9800 Pro
    Sound Blaster Audigy 2ZS Platinum
    Pioneer 10x DVD Drive
    Sony 8x Double Layer DVD-+RW
    Western Digital 120.0GB 7200RPM HD ATA/100
    Western Digital 120.0GB 7200RPM HD ATA/100
    nForce Ethernet Adapter w/Cable line
    Logitech MX500 Optical Mouse
    Logitech Elite Keyboard
    19" Envision Monitor EN985e
    Logitech Z-680 5.1 Speakers

    Could be a fluctuating PSU that's breaking down power to the MB. You have a whole lot of components dragging that PSU down. With what you have in your rig I would run either an Antec or Enermax 550W. Best way to be sure is to borrow a PSU or buy one from a store with a good return policy so that you can return it if indeed it turns out to be the MB. If I don't have your board here on my bench to test the only thing I can suggest to you is to swap out components unfortunately.

  • Need help with jumper settings for k7n2 delta ilsr

    I have a k7n2 delta ilsr and I'm using a AMD 2800+ barton 333 fsb. I'm not sure what the jumper settins are for this cpu. The users guide only shows 133/166 and 200, can anyone help me with the jumper settings.
    Thanks, Ron.

    Hi,
    As your processor is 333FSB - the jumper should be set to 166FSB as should the BIOS. As your RAM CPU combination runs at 2x166=333 or thereabouts.
    Basically, as a general rule, if you halve the FSB speed of your processor you'll get the setting for both BIOS and Jumper. 200FSB=100, 266FSB=133, 333FSB=166 etc. etc.
    Axel  

  • Problem with K7N2 Delta-ILSR, please help

    First off, these are the specs for the computer to which I shall be referring in this post:
    K7N2 Delta-ILSR
    AMD 2700+
    1x512MB PC3200 Memory Corsair CM64SD512
    Seagate Barracuda 80GB 7200RPM SATA ST380013AS
    ATI 9600 Pro
    400 Watt power supply
    Cendyne 52x cd burner
    Here's what happened.  I installed everything with only minor difficulties, mostly due to getting the hard drive to work.  They were worked through with little problem due, in large part, to this forum.  I installed Windows XP, and we ran a number of things with no problem after the OS installation.  The drivers for the video card loaded well.  3DMark2003 ran beautifully.  After I got that working, I went to put my friend's old hard drive in as a slave, so he could get the files off of it.  This seemed to work well enough.  Then we went to load the drivers for the motherboard.  When it got to the audio driver, we got the old "blue screen".  Then the computer reset and tried booting 98 from the old hard drive.  We shut down and disconnected the old hard drive.  Then we restarted to find that after the second screen XP would not begin to boot.  After some playing around we decided it best to reinstall, because with no combination could we get the OS to boot up.  So we reinstalled, with a full format.  This time, the first thing I went for was the motherboard drivers.  It stopped at the audio driver, again, and gave us the old "blue screen", again.  This time, instead of stopping the boot after the second screen, it came up with this message
    Windows could not start because the following file is missing or corrupt:
    \system32\hal.dll.
    Please re-install a copy of the above file.
    Any suggestions would be greatly appreciated before we decide what to do next.  Please let me know if any more information is required.  None of the bios settings have been altered, save to boot from the CD.
    Thank you,
    M.Cordier

    i would test ram
    http://www.memtest86.com
    and go to drive makers site and get their testing utility
    other possibility is a crap psu like them qtecs

  • Anyone help - need I/O plate for K7N2 Delta ILSR??

    I'm based in the UK but will pay P&P worldwide........
    cheers
    D.

    Good luck!
    http://search.stores.ebay.com/ws/search/StoreItemSearch?catref=C5&fcl=3&from=R7&frpp=50&fsoo=1&fsop=1&sacat=-1&satitle=k7n2+delta+ilsr&sbrexp=WD1S&sif=1&sofindtype=0&sofp=4&ssPageName=WD1S
    Edit: If applicable:
    http://www.mycableshop.com/sku/ATXBACKPLATE.htm

  • Help! amd xp3000+ barton temp's.... k7n2 delta ilsr

    Hi all, (sorry for the lengthy post)
    Ive recently built a new system based on the K7N2 DELTA ILSR, great mobo, however my cpu temps are extremely high! on idle 48C and on load nearly 60C. the mobo temp hits approx 40c on load and 34 on idle.
    I had an issue with cooling as the cpu heat diode would freeze my pc as it was hitting temps of 58c on idle. i was using the coolermaster aero 7+.... no good at all!!!!! even when on full rpm. Now im using a vantec 80mm fan on a Thermalright SLK-800A. much improved, however still extremely hot.
    after reading this review (section headed: Heat Dissipation: Thermal Conditions and S2K Bus Disconnect) :
    http://www.xbitlabs.com/articles/cpu/display/athlonxp-3000.html
    ......on "S2k bus disconnect" created by AMD for the barton range.
    As the article states, it reduces Cpu temps ALOT!! but im not too sure ion how to activate it or even if my MSI motherboard supports it....
    Can anyone shed some light???
    system:
    Radeon 9800
    1GB 3200 Ram
    xp 3000+ Barton
    Sound Audigy 2
    Thanks, Sav

    Sorry about the long reply!!! the first thing i would like to say is why does this happen at 58C even with the bios temp settings diabled??? pehapes MSI could Answer this?
    I have spent countless hours trying to fix this problem and a lot of £££. A bit of background to me I am a design engineer and i like my PC to work well. I have the following main components
    xp3200+ based system (Max die 85C)
    with dual 512ddr sticks running at 400mhz
    Matrox Parphilia
    10K SATA hard disk
    7,200 133ATA hard drive
    Plus motherboard Nvidia chipset
    these all kick out a lot of heat the (CPU contributing 76.8w).
    first i started out with a very cheap case and standard amd heatsink. I found after about 5 minutes my pc kept crashing i automatically thought that it was probably the case temperature so monitored this found every time cpu reached 58C it crashed on the dot. The only conclusion i can draw from this that this MB has some thermal protection that can not be switched off but i am guessing perhapes MSI would like to answer this.
    I quickly decided as an engineer that the best thing would be to go and buy a aluminuim case with lots of case fans (Basically a big heatsink itself). After a lot of searching i settled for a Coolermaster ATC110. It has four case fans all run at full speed all the time. Now this stoped the crashing problem it only now crashes if i put it under continous loading. Then i went out and bought a new cpu heatsink to replace the amd standard one. This had a minor effect on cpu temp but again under high loads the system crashed at 58C. Obvoiusly as an engineer i satred to think that the amount of noise the system with all its fans going at max is like being put in a wind tunnel.
    I then turned to looking at the thermal diserpation requiremnts of all the bits in my system. I worked out that i need to disserpate 281Wmax of heat with my current setup. The kind of heat a small electric fire produces!!!. I begun to wounder if i could shift enough air through the two exhaust fans at the rooms ambient temp to do this. After some calculations I found that my case exhaust case fans are only just surfficent to disspate this amount. Which could explain this the crashing. because the higher the case temp the lower the capability of the heatsinks to conduct heat away from the item.
    In the end i gave up with active cooling methods (heatsinks and fans) and realised my only option was to go for external cooling. I now have the system setup with a koolance exos cooling both hardisks graphics card cpu and MBchipset. I know this is very extreme but the case fan noise got to me now i have disconected all case fans except for the ones in my thermaltake power supply which are virtually silent. After about 12 evenings of testing and installation I now have a system which is not only stable but the CPU temp is only 32C.
    Obvoiusly getting the heat out of the case is a good idea. The Exos is only running at it's lowest setting which means the  fans arnt making any noticable noise.
    MOST IMPORTANTLY IT DOES NOT CRASH ANY MORE. AND THERE IS THE PSSIBILTY OF OVERCLOCKING.
    The question still remains though why 58C?

  • MSI K7N2 Delta-ILSR Wont boot up (no display no bios)

    Hi
    i bought a AMD Athlon XP 3200+ & MSI K7N2 Delta-ILSR.
    unfortuntly i can't boot it. it wont show anything on screen.
    i have tried anything i red in this forum (clear cmos... safe mode jumper...strip all parts...)
    all i get is : 
    blank black display, no beeps and keyboard lights flashes over and over (when connected to a KVM hub), when conected directly to keboard the lights flashes only once but stil black display and no beeps (i hear on speake,when powering up PSU, a silent short noise, no beep).
    power suply turns on (new one 500w), i tried agp video card and replaced with pci video card.
    memory is kingstone 512mb pc3200 400MHz x2, i tried only one of them and both in diferent sockets.
    cpu: AMD xp 3200+ 400fsb.
    i did succed to go into bios only once, after lots of resets and shutdowns and bios clear (after ouers)
    i choosed in the bios: load bios defaults, and thats it. i hoped it starts up but nothing.
    i did all testing i know (checked all pins, cables, clear cmos...all, you name it)
    all parts are brand new (except motherbord. it's seconds hand from eBay. i've bean talled that it works fine)
    i also e-mailed MSI support that question. (2 days ago. no answer yet)
    oh...and i have a pci POST diagnostic card and its 7seg display don't shows any numbers, only when once i succed to get into bios. i don't have the msi original D-Breket addon diag.
    can you help me? 

    hi guys
    here is my PSU specs:
    Colors-It 500w-Max Silent ATX Power Supply
    Voltage 115/230V
    Current 10A/5A
     Frequency 60/50Hz
    +3.3   +5    +12   -12     -5      +5SB   BLK    GRN    GRY
    30A    50A  15A   1.0A   1.0A   2.5A   COM   P-ON   PG
    connectors:
    ATX-2.03 Connector: 1
    ATX-12V Connector: 1
    CD-Rom/HD 4 Pin connector: 6
    Floppy 4 Pin Connector: 2
    Serial ATA Connector : 1
    cpu: AMD Athlon XP 3200+
    MotherBoard: MSI K7N2 Delta-ILSR   More: http://www.msicomputer.com/product/p_spec.asp?model=K7N2_Delta-ILSR&class=mb
    Memory: kingstone 512mb pc3200 400MHz x2      More: http://www.ec.kingston.com/ecom/configurator/PartsInfo.asp?ktcpartno=KVR400X64C3A/512
    i have other brand of memory moduls (micron pc2300) i tried them too. no go.
    i tried other PSU, i pulled from my brothers pc (amd xp 1400+).
    as i said before, i have  pci POST diagnostic card so it could tell me any problem. iguss it's the mobo, posibly bios upgrade.
    but if mobo not showing bios, i can't update bios from floppy.
    and the tested the mobo out side the case on a antistatic mat and i useed an antistatic strip.
    as i said i could get into the bios once, after many resets....choosed 'load bios defaults..', restarted and.....no go.

  • K7n2 delt ilsr instabilty problem update

    have a k7n2 delta ilsr have an issue where it is unstalble ie get bsod at welcom  etc at 400 fsb ie 200 setting in bios will run at 166 in safe mode the 3200 cpu is reconised as at 2.39 ghz it should be 2.2 ghz if i run cpucz it says the multiplier is *12 is this a motherbord fault have updated bios too 7.8 latesed have tried diff make of memory power supply but i think the problem is looking me in the face in the fact that the cpu is reconised as 2.39 ghz and the muilt is *12 i think it should be * 11 can any body help regards bazer

    yes has latesd bios    AMD Athlon(tm) XP 2700+ here is some info pc wizard 2005
    Codename :   Barton
    Revision :   A2
    Technology :   0.13µ
    CPU ID :   6.A.0
    CPU IDEx :   7.A.0
     Features :   
    VME - Virtual Mode Ext. :   Yes
    DE - Debugging Extension :   Yes
    PSE - Page Size Extension :   Yes
    TSC - Time Stamp Counter :   Yes
    MSR - Model Specific Registers :   Yes
    PAE - Physical Address Extension :   Yes
    MCE - Machine Check Exception :   Yes
    APIC - Local APIC Built-in :   Yes
    SEP - Fast System Call :   Yes
    MTRR - Memory Type Range Reg. :   Yes
    PGE - Page Global Enable :   Yes
    MCA - Machine Check Architecture :   Yes
    PAT - Page Attribute Table :   Yes
    PSE36 - 36-bit Page Size Extension :   Yes
    PSN - Unique Serial Number :   No
    DS - Debug Trace & EMON Store :   No
    ACPI - Software Clock Control :   No
    SS - Self Snoop :   No
    TM - Thermal Monitor :   No
    HTT - Hyper-Threading :   No
    SBF - Signal Break on FERR :   No
    MON - Monitor/Mwait :   No
    DSCPL - CPL qualified Debug Store :   No
    TM2 - Thermal Monitor 2 :   No
    CID - Context ID :   No
    EST - Enhanced SpeedStep Tec...   No
    NX Bit - No-execute Page Protec...   No
    VMX - Vanderpool Technology :   No
     Miscellaneous :   
    FPU - Co-processor Built-in :   Yes
    CX8 - CMPXCHG8B :   Yes
    CX16 - CMPXCHG16B :   No
    CMOV - Conditionnal Move Inst. :   Yes
    CLF - Cache Line Flush :   No
    FXSR - Fast Float Save & Restore :   Yes
    DAZ - Denormals Are Zero :   No
    MMX Technology :   Yes
    SSE Technology :   Yes
    SSE2 Technology :   No
    SSE3 Technology :   No
    X86-64 Technology :   No
    AMD MMX Technology :   Yes
    3DNow! Technology :   Yes
    Extended 3DNow! Technology :   Yes
    3DNow! Pro Technology :   Yes
    SMP - MP Capability :   No
     Power Status :   
    Voltage Control :   No
    Frequency Control :   No
    Thermal Sensor Built-in :   Yes
     Addressing Information :   
    Physical Addressing max. :   34-bit
    Linear Addressing max. :   32-bit
     Mainboard Upgradebility :   
    Socket/Slot :   Socket A
    Upgrade interface :   ZIF Socket
    Supported Speed :   2200 MHz (or more)
    Supported Voltage :   1.6V
    al Information :   
    Performance Rating :   PR-3300 (estimated)
    Real Frequency :   2164.89 MHz
    Multiplier :   12x
     Front Side Bus Information :   
    FSB Frequency :   180.4 MHz
    Bus Speed :   360.8 MHz (DDR)
     Initial Frequencies :   
    Frequency :   2000 MHz
    FSB Frequency :   166 MHz
     Control Clock Frequency :   
    Type :   None
     Thermal Information :   
    Core Power :   63.42 W (estimated)
    Resistance :   0.46 °C/W (estimated)
     Processor Performance Information :   
    Throttle Mode AC :   None
    Throttle Mode DC :   Adaptive
    Current Configuration :   None
    Throttle :   2164 MHz
    CPU Throttle Temperature :   60°C
    CPU Shutdown Temperature :   100°C
    eneral Information :   
    A0 (RAS 0) :   256 (Single Bank)
    A1 (RAS 2) :   256 (Single Bank)
    A2 :   Empty
     Memory Controller Information :   
    Memory Controller :   Standard, EDO
    Number of connectors :   3
    Max. Module Size :   32 MB
    Max. Memory Size :   96 MB
    Supported Speed :   70ns, 60ns
    Supported Voltages :   5v
    Error Detection Method :   8-bit Parity
    Error Correction Capability :   Unspecified
    Current/Supported Interleave :   1-way/1-way
     Chipset Information :   
    Type :   DDR-SDRAM PC2900
    Frequency :   180 MHz
    FSB/RAM Multiplier :   1/1x
    Channels :   Dual
    ECC Diagnostic :   No
    CAS Latency (tCL) :   3 clocks
    RAS to CAS (tRCD) :   3 clocks
    RAS Precharge (tRP) :   3 clocks
    Cycle Time (tRAS) :   8 clocks
     Information SPD EEPROM (A0) :   
    Manufacturer :   Samsung
    Part Number :   M3 68L3223ETM-CCC 
    Serial Number :   F6016243
    Type :   DDR-SDRAM PC3200 (200 MHz)
    Size :   256 MB (1 rows, 4 banks)
    Module Buffered :   No
    Module Registered :   No
    Width :   64-bit
    Error Correction Capability :   No
    Max. Burst Length :   8
    Refresh :   Reduced (.5x)7.8 µs, Self Refresh
    Voltage :   SSTL 2.5v
    Supported Frequencies :   166 MHz, 200 MHz
    CAS Latency (tCL) :   2.5 clocks @166 MHz, 3 clocks @200 MHz
    RAS to CAS (tRCD) :   3 clocks @166 MHz, 3 clocks @200 MHz
    RAS Precharge (tRP) :   3 clocks @166 MHz, 3 clocks @200 MHz
    Cycle Time (tRAS) :   7 clocks @166 MHz, 8 clocks @200 MHz
     Information SPD EEPROM (A1) :   
    Manufacturer :   Samsung
    Part Number :   M3 68L3223ETM-CCC 
    Serial Number :   F6056193
    Type :   DDR-SDRAM PC3200 (200 MHz)
    Size :   256 MB (1 rows, 4 banks)
    Module Buffered :   No
    Module Registered :   No
    Width :   64-bit
    Error Correction Capability :   No
    Max. Burst Length :   8
    Refresh :   Reduced (.5x)7.8 µs, Self Refresh
    Voltage :   SSTL 2.5v
    Supported Frequencies :   166 MHz, 200 MHz
    CAS Latency (tCL) :   2.5 clocks @166 MHz, 3 clocks @200 MHz
    RAS to CAS (tRCD) :   3 clocks @166 MHz, 3 clocks @200 MHz
    RAS Precharge (tRP) :   3 clocks @166 MHz, 3 clocks @200 MHz
    Cycle Time (tRAS) :   7 clocks @166 MHz, 8 clocks @200 MHz

  • Internet Connection Problem on MSI K7N2-Delta-ILSR

    Hi, recently I buy an MSI K7N2-Delta-ILSR.I have a problem when I was trying to connect to the Internet through my modem on WinXP Pro SP1. It bring me up an error message 678 ( The computer that was tried to connect did not respond...). I have also a second hard disk with Mel windows. On disk the disk with the Mel I don’t have any problem with the internet connection. All my settings are same on WInXP pro and Mel.I have checked I thousand times. My computer configuration is:
    Athlon XP 2400+ Overclocked to 2205MHz
    2 memory modules of 256MB 400 manufactured by Samsung
    TharmalTake Volcano 11
    Triplex Xabre 400 PRO with 128MB
    Hercules Gamesurrround Fortissimo III 7.1
    Microcom InPorte Home modem 56k
    Leadtek winfast 2000 (TV/FM radio)
    Acard SCSI controller (Acard AEC-6710D) for my scanner
    WesternDigital WD800 GB
    WesternDigital  15.3gb
    Bios ver.7.4  
    Can anyone help me?

    Quote
    Originally posted by Roger Wilco
    Hmmmmm, I\'m also having a problem with the onboard lan of the K7N2 Delta.
    I have an ADSL connection, and have an Alcatel SpeedTouch Home modem.
    I pretty much get the same error as SiliconMan (The computer that was tried to connect did not respond...)
    I ended up giving up on it for the time being, just using my SMC NIC. Would be quite interested in finding out what the problem is though.
    Anyone else in the same boat?
    Hi,
        Your problem is not the same, SiliconMan is trying to connect with a dial-up modem not LAN. Your problem sounds like it may be configuration, do a search on this post, I'm sure you will find people with onboard LAN troubles. It's hard to troubleshoot though since you didn't provide any info about your computer. Good Luck  
    Rob

  • Data corruption on MSI K7N2 Delta ILSR

    Hi all,
    Just got my new MSI K7N2 Delta ILSR up and running.
    Got some issues with the memory running at 200mhz while the Barton core of my Athlon Xp 2600+ was running 166mhz, this had to be 1:1 (thx forum  )
    While running the default bios settings with cpu/mem at 166/166 fsb everything is stable as hell. I have been running Prime95 for 2 days now and using the system for dvd ripping/encoding, UT2004 gaming etc.
    Then the overclocking began   I'm using the standard AMD cooler that came with my boxed Xp2600+ so I didn't expect an FSB of 200mhz.
    I stopped at an FSB of 190mhz...been crunching Prime95 for 18 hours now and again very stable.
    Now comes the problem : Sometimes I get crc errors when installing a game or decrypting a dvd!! But how can this be? Prime95 is stable at this 190fsb overclock.
    When using an FSB of 166mhz no data corruption or crc errors.
    What can this be? It's not the cables because they're all the same as in my old setup which was running (ahum...walking) stable. PCI/AGP speeds are locked when overclocking...
    Only thing I can think of is the power supply. I've read in a warning post from Bas that the Q-Tec 550w psu I have is crap. So my guess is PSU, but maybe it's something else I'm forgetting...Any suggestions??
    The stupid thing is when I'm not overclocking I don't have the data corruption problems, but I'm still using the same crappy Q-Tec 550w PSU.
    Help!  
    gr,
    Remco

    Hmmm, that's curious. On the MSI K7N2 Delta ILSR product page Kingston memory is recommended  
    Ok, did a Memtest86 v1.11 pass at cpu/dimm 166/166 - no problems whatsoever. I think using Prime95 would have revealed memory problems...but will do another pass with cpu/dimm at 190/190.
    Can overclocking affect the Promise Raid Controller?? It should be locked like the PCI/AGP but who knows...
    Well, I still have to replace my PSU but I'm not 100% sure that this is the problem. What PSU would you recommend? ...and I'm also thinking about replacing the standard CPU cooler, any advice is welcome  
    gr,
    Remco

Maybe you are looking for

  • Slow internet speed on 1 of 2 wired desk top PCs

    I have 2 PCs that sit next to each other and are wired to the FiOS router. Both are running WinXP Pro and are up to date. PC 1 gets 9.6 mbps up and down. PC 2 gets 22 to 30 mbps up and down. PC 1 is a more powerful up-to-date machine. After switching

  • How to Re-Download movies and tv shows

    My hard drive recenctly crashed forcing me to reinstall OSX i had a bunch of stuff i donwnloaded from the itunes store that adds up to alot of money i am wondering if there is any possible way of getting them back? the items i downloaded are listed b

  • ITunes 7 wont group edit Show Titles

    If I select a few TV Shows, iTunes 7 will not allow me to change the Show Title. I can do it one show at a time. Also, the Show Title field does not suuport auto-fill like all the other fields. Plus, iTunes 7 is a dog in terms of performance. I have

  • CC that is not showing up as included in my BK

    Hello all. I have a Chase CC that I'm pretty sure was included in my BK, but doesn't show that on my credit reports.  It is showing Purchased by another lender or Charged off account.  It's also showing many late pays when my attorney told me to stop

  • I would like to now how to delete a photo.  Plain and simple.

    Why is it that delete does not mean delete?