Upgrade to OS 10.5 + DLT SCSI Support?

I'm wondering - if I upgrade to OS 10.5 will my SCSI card (ATTO) and DLT tape drive DLT80) still work?

I have not tried that combination but you may want to drop a note to ATTO to see what they support. Regardless of the answer clone your boot drive before any updates so you can restore it if needed (or stick another drive/boot partition in.)
One last thing, I tend to stay conservative on these things,if I have a machine that is working well I usually will not update it unless there is a real pressing reason and unless there is a good reason for you to want to update to Leopard on a production machine, you may want to think about it a bit (or just get another Leopard boot disc in there.)

Similar Messages

Upgrading to Mountain Lion and lack of support for Power PC Applications

Hi
I have been reading with interest the comments and questions about this.
I am a bit of a novice with pc/mac terminology so was baffled to receive the message about Power PC Applications. I merely upgraded to Lion thinking it would be great to have the latest software on my Mac but am now unable to log into work remotely.
I log in using "Cryptocard" software and tokens. Does anyone have any experience of getting around the power pc application issue using the Cryptocard software? I an hoping I wont need to revert back to the previous software after spending £13 upgrading it!
Have contacted Cryptocard for support but comments are welcome
Many thanks

I have no experience with Cryptocards, but,
Workarounds:
1. Revert to the original OS X that was operating on your Mac;
2. Upgrade your PowerPC applications to Intel versions;
3. Replace your software with alternatives that work in Lion;
4. Partition your hard drive or add an external hard drive and install Snow Leopard into it and use the "dual-boot" system to run your PPC applications but not concurrently with Lion; or
5. Do what I do, install Snow Leopard (with Rosetta) into Parallels in Lion:
[click on image to enlarge]
Full Snow Leopard installation instructions are here:
http://forums.macrumors.com/showthread.php?t=1365439

Problem viewing forms.This form is not supported with the current version of Adobe Reader.Upgrade to the latest version for full support. That does that mean exactly?

Problem viewing forms.This form is not supported with the current version of Adobe Reader.
Upgrade to the latest version for full support.
What exactly do I need to do?

That means you were probably using Adobe Acrobat to view PDF's. Acrobat is totally unnessary, you can view PDF's in Preview (Applications - Preview).
BTW PLEASE complete your profile. It's very difficult to help someone when they don't provide any information about their system. You can easily do this by clicking Your Stuff in the upper right of this page, then click Profile and fill in the pertinent information.

Where can i download quicktime 7.5.5? A compatibility version gets downloaded but its not what I need. Im unable to open my ITUNES without the quicktime 7.5.5 upgrade or higher. Anything higher isnt supported by my mac ( OS X 10.5)

where can i download quicktime 7.5.5? A compatibility version gets downloaded but its not what I need. Im unable to open my ITUNES without the quicktime 7.5.5 upgrade or higher. Anything higher isnt supported by my mac ( OS X 10.5)

I had the same problem when re-installing my old iBook recently. You can find it here:
http://support.apple.com/kb/DL27

7.01 to 7.3 Upgrade - Logon Screen - "Logon Problems? Get Support" occuring

Hi
We have upgrade our ABAP and JAVA stacks from NW 7.01 to NW 7.3.
After the upgrade is the "Logon Problems? Get Support" occuring on our portals logon screen. In 7.01 this was controlled with the parameter ume.logon.logon_help - however after the upgrade we do not see this parameter anymore.
Screen dump (requires a couple of clicks)
http://www.filefactory.com/file/c26d20b/n/Portal_Logon_Page_Issue.jpg
Any idea about how we remove the "Logon Problems? Get Support" part?
Thanks and kind regards,
Torben

Hi Torben,
On my fresh 7.3 installation, everything is clean and ... fresh ...
So, for example, the built in group AnonUsers only has the user Guest as it's solely relation (no parent, no child groups); the guest user has the Guest role, which has (via it's groups) roles Everyone and Guest; onbly the role Everyone as got UME actions.
All together, this sounds much like an upgrade issue (on my fresh 7.3, there is no group "J2EE_GUEST" at all).
Two possibilities to go:
- Open an OSS message (should be done in any case probably, to report this issue to SAP, so that this can be fixed);
- Check the UME consistenty by yourself (http://help.sap.com/saphelp_nw73/helpdata/en/44/aecb4253217037e10000000a422035/frameset.htm)
Maybe the second point already will fix some things; would be great for you, anyhow, I still would advise to report this issue officially to SAP.
Hope it helps
Detlev

Just upgraded Tiger to Leopard. Clarisworks not supported. I can successfully convert CW4.0 doc's to AW6.0 doc's using MacLink Plus Deluxe but the problem is I than cannot print them or convert to PDF, either.

Just upgraded Tiger to Leopard. Clarisworks not supported. I can successfully convert CW4.0 doc's to AW6.0 doc's using MacLink Plus Deluxe and then work on them but the problem is that I cannot print them. Neither can I convert to PDF.

If I was trying to get someone else to do my work,
I wouldn't be posting this saying what I have said
would I? I'm not unwilling to do the work myself.From what was stated in your OP, it seemed that you
were.I'm sorry if it seemed that way. I don't want something for nothing. I've spent MANY hours, which I don't have, trying to work this out. I have hit a point where I don't think my expertise is going to solve the problem. That's why I've turned to some experts who might say something along the lines of, "Hey, I know what that is...you're compiling against... and on the Unix box, it's compiling against..." I was NOT looking for something like, "See the code below that fixes your problem."
The only problem is that I don't have direct access
to the sun unix machines I'm running the app on,
so I can't run a profiler on it. Ah, okay. So the only knowledge you have of how it
performs on those machines is from your instructor
running it and then telling you how long it took?No. I can SSH into the servers and run the program from a command line. But I wouldn't be able to install any profiler programs.
You could ask your prof to run it with -Xprof or
-Xhprof or whatever. Or you could put in a bunch of
timing statements to get a rough idea of which parts
are making it take that extra 39 minute or whatever.is -Xprof a java command line option? If so, I will look into doing that. Maybe it's available on the machines at school. Thanks for that input.

TS4268 FaceTime doesn't work after upgrade to ISO 6.0.1, apple support team has sent an auto reply that doesn't help .... Any suggestion will be appreciated

FaceTime doesn't work after upgrade to ISO 6.0.1, apple support team has sent an auto reply that doesn't help .... Any suggestion will be appreciated

Hi AnaMusic,
It was working perfectly before the upgrade to ISO 6.0.1, but now I can't log in using my apple ID ... I have tried all suggestion from Tom but nothing does work. I keep getting the message "FaceTime can't log in, check your network" is nothing wrong with my network everything else works fine, I can log in into FaceTime using my IPad 2 and my apple ID.
I'm currently working in Korea, but I bought the IPad in Australia,
Regards,
Namur

Maverick. Mail attachment now says can't be used because PowerMac no longer supported. Attachment worked before upgrade. Says Microsoft Word no longer supported.

A lease agreement attached to an e-mail opened fine in Pages with Mountain Lion this morning. I upgraded to Mavericks this afternoon and neither a revised offer nor the old one can be opened. A screen comes up saying I can't open Microsoft Word as PowerPc applications are no longer supported.
What can I do? Is there a way to dump Mavericks?

In Mountain Lion this morning, when I clicked on the attachment to the e-mail, I got a screen saying would I like to try opening the attachment with: And it gave me a list of choices, including Pages. Pages had no problem opening the attachment. Now after I upgraded to Mavericks I get the messages about PowerPC! No choices!

Help! bulk license photoshop 7.0 with Cs3 upgrade won't work when reinstalling - Adobe support can't help

I've installed/reinstalled CS3 (upgrade over Photoshop7) a few times since 2007 when I've upgraded my pc - from the first install I had to contact their Aussie 1800 number because the Photoshop disk was a bulk license version and it didn't like the key when CS3 did an upgrade check. Spent over an hour today on a chat with Adobe and they will no longer help me as they aren't trained on PS 7 or CS3. ANY HELP would be appreciated

If your products are registered with Adobe, they can unlock CS3. It's called a "challenge code".
Apparently, Adobe has a challenge code system. So, if you have the old serial number from the upgrade and you call customer support. Customer support has a challenge code procedure where they give you a code that overrides the problem. Unfortunately, it took me 5 calls to customer support before I found someone who knew how to do it. The key term is "Challenge Code"
Error "This serial number is not for a qualifying product" | CS6, CS5.5, CS5
Important: We can unlock your serial number after we first verify that you qualify for the upgrade. When you contact us, be at your computer to complete the following upgrade verification workflow.
Register your product.
Contact us. You'll complete the next steps with a staff member.
Do one of the following in the Serial Number Upgrade screen:
Windows: Press Ctrl+Shift and then double-click.
Mac OS: Press Command+Shift and then double-click.
The Upgrade Code window appears.
Read the Challenge Code to the support staff member.
Enter the Support Code (that Adobe Support provides) into the Support Code field, and then click Next.
Gene

While upgrade to LWAP error : AP Radios not supported.

Hello Experts,
i am using upgrade tool and LWAP image c1100-rcvk9w8-tar.123-11JX1.tar.but still i am not able to upgrade to LWAP.
when i check detail log in upgrade tool its shows the AP Radios not supported.can somebody help me in this regard. Thank you in anticipation..
Below are the logs of the AP while doing LWAP upgrade
*Mar 1 00:00:05.712: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to r
eset
*Mar 1 00:00:05.713: %DOT11-2-NO_FIRMWARE: Interface Dot11Radio0, no radio firm
ware file (flash:/5101.img) was found
*Mar 1 00:00:05.714: %DOT11-2-NO_FIRMWARE: Interface Dot11Radio0, no radio firm
ware file (flash:/5101.img) was found
*Mar 1 00:00:05.715: %DOT11-2-RESET_RADIO: Interface Dot11Radio0, Radio firmwar
e file not found, Trying hardware reset on radio
*Mar 1 00:00:12.706: %DOT11-2-NO_FIRMWARE: Interface Dot11Radio0, no radio firm
ware file (flash:/5101.img) was found
*Mar 1 00:00:12.707: %DOT11-2-NO_FIRMWARE: Interface Dot11Radio0, no radio firm
ware file (flash:/5101.img) was found
*Mar 1 00:00:13.008: %DOT11-3-POWERS_INVALID: Interface Dot11Radio0, no valid p
ower levels available
*Mar 1 00:00:13.008: %DOT11-3-POWERS_INVALID: Interface Dot11Radio0, no valid p
ower levels available
*Mar 1 00:00:13.008: %DOT11-2-RADIO_FAILED: Interface Dot11Radio0, failed - fir
mware file not found
-Traceback= 18F68 405868 3FDFB0 4072E0 129B34 129BDC 116F0 11904 1357B0
*Mar 1 00:00:13.008: %DOT11-3-POWERS_INVALID: Interface Dot11Radio0, no valid p
ower levels available
*Mar 1 00:00:13.008: %DOT11-3-POWERS_INVALID: Interface Dot11Radio0, no valid p
ower levels available
*Mar 1 00:00:15.059: %SYS-6-LOGGERSTART: Logger process started
*Mar 1 00:00:15.061: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to
up
*Mar 1 00:00:16.061: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern
et0, changed state to up
*Mar 1 00:00:16.617: %SYS-5-CONFIG_I: Configured from memory by console
*Mar 1 00:00:16.617: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1100 Software (C1100-K9W7-M), Version 12.3(8)JA2, RELEASE S
OFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Tue 30-May-06 17:41 by pwade
*Mar 1 00:00:16.618: %SNMP-5-COLDSTART: SNMP agent on host RH-W-D36-AP1121G is
undergoing a cold start
*Mar 1 00:00:16.642: Writing radio coredump to 'flash:/r0.rcore'
*Mar 1 00:00:17.334: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, chan
ged state to up
*Mar 1 00:00:31.891: Writing radio coredump to 'flash:/r0.rcore'
*Mar 1 00:00:37.051: Interface Dot11Radio0: not starting because stop-on-failur
e set
*Mar 1 00:00:37.058: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to do
wn
*Mar 1 00:00:38.058: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio
0, changed state to down
RH-W-D36-AP1121G#
Sh ver : and sh flash
RH-W-D36-AP1121G#sh fla
RH-W-D36-AP1121G#sh flash:
Directory of flash:/
    2 -rwx     3650405 Mar 15 1993 18:04:33 +00:00 c1100-k9w7-mx.123-8.JA2
    3 -rwx         272 Mar 01 2002 00:00:16 +00:00 env_vars
    7 -rwx      525184 Mar 01 2002 00:00:37 +00:00 r0.rcore
    5 -rwx          79 Mar 01 2002 02:12:52 +00:00 private-config
    4 -rwx        2072 Mar 01 2002 02:12:52 +00:00 private-multiple-fs
    6 -rwx        6626 Mar 01 2002 02:12:51 +00:00 config.txt
    8 drwx         128 Mar 01 2002 02:31:37 +00:00 c1100-rcvk9w8-mx
7741440 bytes total (1694208 bytes free)
RH-W-D36-AP1121G#sh ver
Cisco IOS Software, C1100 Software (C1100-K9W7-M), Version 12.3(8)JA2, RELEASE S
OFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Tue 30-May-06 17:41 by pwade
ROM: Bootstrap program is C1100 boot loader
BOOTLDR: C1100 Boot Loader (C1100-BOOT-M) Version 12.2(8)JA, EARLY DEPLOYMENT RE
LEASE SOFTWARE (fc1)
RH-W-D36-AP1121G uptime is 23 minutes
System returned to ROM by reload
System image file is "flash:/c1100-k9w7-mx.123-8.JA2"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-AP1121G-E-K9     (PowerPCElvis) processor (revision A0) with 15038K/13
36K bytes of memory.
Processor board ID FOC08301UAW
PowerPCElvis CPU at 197Mhz, revision number 0x0950
Last reset from reload
1 FastEthernet interface
1 802.11 Radio(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:11:93:F1:0E:BA
Part Number                          : 73-7886-07
PCA Assembly Number                  : 800-21481-07
PCA Revision Number                  : A0
PCB Serial Number                    : FOC08301UAW
Top Assembly Part Number             : 800-22053-04
Top Assembly Serial Number           : FHK0835V1J0
Top Revision Number                  : A0
Product/Model Number                 : AIR-AP1121G-E-K9
Configuration register is 0xF
RH-W-D36-AP1121G#
Also i reformated the iamge K9w7 again as i was only able login through CMD and while explorer still this error coming-
RH-W-D36-AP1121G Home Page
Cisco Systems
Accessing Cisco AIR-AP1121G-E-K9 "RH-W-D36-AP1121G"
Web Console - Manage the ap through the web interface.
Show diagnostic log - display the diagnostic log.
Monitor the router - HTML access to the command line interface at level 0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15
Show tech-support - display information commonly needed by tech support.
Extended Ping - Send extended ping commands.
Help resources
CCO at www.cisco.com - Cisco Connection Online, including the Technical Assistance Center (TAC).
[email protected] - e-mail the TAC.
1-800-553-2447 or +1-408-526-7209 - phone the TAC.
[email protected] - e-mail the HTML interface development group.
Appreciate your quick response and suggestions.

Hello ,
What are you refering by word Broken AP(1121series ) how do i confirm it is broken.
when i access it from CLI it looks completely fine m but when i do GUI access it shows the above GUI screen.
Can you Please help me to how to to check it is damaged.
Appreicate all your respnse.
Regards,
KA.

How do I upgrade my late 2012 27" iMac to support the new 802ac wifi?

I want to buy the new Airport Extreme to get super fast wifi, but as I understand it theres no use at the moment as the current latest versions of the iMac's only support up to 802n. Is this correct or will I need to upgrade the wifi chip in my iMac to be able to use the super fast capabilities of the new airport extreme?

I have to say thaat this is the sort of thing that reaally gets me! I've had my new iMac for a couple of months now so why oh why didn't they build it with 802.11ac? It's ludicrous that the only thing that supports it is the new MBA's!! Surely the new TC has been on the design table long enough that this could have been thought of in the latest iMacs and MBP's.
So I'll not be buying the latest TC (too tall to fit in my space anyway) but luckily there are some refurbished last gen TC's in the store for a reasonable price.

HT1338 How can I upgrade to Lion? My iMac cannot support Mountain Lion but I do not see Lion in the app store anymore.

I want to upgrade my 2006imac with 3GB ram but mountain lion requires 4gb. Can I purchase mountain lion in the app store and it will install lion or will it just charge me $20 for an OS I can't use?

A 2006 iMac cannot run Mountain Lion at all. Mountain Lion only requires 2 GB of RAM, but your model has a video controller which doesn't support features required by Mountain Lion, so Mountain Lion does not support your model. The earliest iMac which can run Lion is the mid 2007 model (aluminium body). A full list of supported models is available here.
If you attempt to buy Mountain Lion in the App Store using your 2006 iMac, the sale will not proceed and you will get an error message saying you cannot purchase Mountain Lion because it is not compatible with your computer. You will not be charged.
If you are currently running Snow Leopard and want to upgrade to Lion, but didn't already purchase Lion (e.g. for use on another computer), it is apparently possible to place a special order for Lion via a telephone call to Apple Customer Support. (I say "apparently" because there have been reports that Apple told some people this was the correct solution, but early attempts to place an order were refused with Apple Support claiming they weren't selling Lion at all. I think this was a temporary situation and it should be resolved by now.) There are links to support telephone numbers here.
Apple will charge you the standard retail price for Lion (e.g. US$29.99 in the US) and supply you with a "redeem code" for the App Store. That is entered by going to the Featured category in the toolbar, and clicking Redeem under the Quick Links heading on the right side. Once your code is redeemed, Lion will be added to the list of purchases for your Apple ID, and you can download and install it.
If you had already bought Lion for use on another computer, you can re-download it from the Purchases list in App Store, but there might be a couple of catches:
1. Some people have found that Lion was added to their list of hidden purchases. You need to unhide it first. Do this by going to your Account page (under Quick Links, or "View My Account" under the Store menu in the menu bar). If you have hidden purchases, there will be a "View Hidden Purchases" link, and from there you can unhide Lion.
2. If you are running Lion and want to redownload the installer on that computer, you may need to hold down the Option key when clicking on the Purchases heading in the toolbar, to enable the download button for Lion.

Upgrade to CS4 fails - how to contact support

Hi
I am trying to upgrade from CS3 to CS4 in a Windows VISTA environment and the installation of Bridge and CS4 fails. The message is:
Adobe CMaps CS4
Error:
Error 1603. Error 1714.The older version of Adobe CMaps CS4 cannot be removed. Contact your technical support group.
It's probably really simple but I can't find how to email Customer Support.
Can anyone point me there?
Thanks
Rob

at the bottom of every page here is a "contact us" link:
http://www.adobe.com/aboutadobe/contact.html

Is direct upgrade from 2.0 to 3.2 supported?

I couldn't find anything in the manuals about supported upgrade paths, so I gave the upgrade a go but @apexins failed with a whole load of errors (which I didn't capture :-()
Before I go back and pick the bits apart and try again, is it supported to go straight from 2.0 (HTML DB) to 3.2 (Application Express) or should I go via 3.0, or something? I was wondering if the errors are caused by the name change of schemas from HTMLDB_xxx to APEX_xxx.
Thanks,
Paul

Ignore that, I found the problem. I'd run out of space in a tablespace.
Sorry for the noise.
Paul.

I have Mac version 10.3.9 and would like to upgrade my Firefox to a version that supports Google calendar.

I have a Mac version 10.3.9 and use Google email and calendar, and am now getting messages that they will be phasing out support for my browser, which is Firefox 2.0.0.20
The new Firefox version offered requires Mac 10.4 or above. Can I upgrade my Firefox to meet the Google requirements without upgrading my Mac?

You can alco check using the model number.
Check that your computer is compatible with Mountain Lion.
To check the model number hold down the option/alt key, go to the Apple menu and select System Information.
iMac (Mid 2007 or newer) model number 7,1 or higher
MacBook (Late 2008 Aluminum, or Early 2009 or newer) model number 5,1 or higher
MacBook Pro (Mid/Late 2007 or newer) model number 3,1 or higher
MacBook Air (Late 2008 or newer) model number 2,1 or higher
Mac mini (Early 2009 or newer) model number 3,1 or higher
Mac Pro (Early 2008 or newer) model number 3,1 or higher
Xserve (Early 2009) model number 3,1 or higher
Your Mac needs:
OS X v10.6.8 or OS X Lion already installed
2 GB or more of memory
8 GB or more of available space
Check to make sure your applications are compatible. Application Compatibility

Upgrade to OS 10.5 + DLT SCSI Support?

Similar Messages

Maybe you are looking for