Upgraded iMac to ML but not my MacBook Pro and the MBP will not print wirelessly
Upgraded iMac to ML and can print wirelessly to HP5200C, but Mac Book Pro, which is not yet upgraded to ML will not.
Do you have the latest HP drivers, available from Apple here, on your MBP?
I see that the HP Deskjet 5520 series are supported...
Clinton
Similar Messages
-
I have recently bought a brand new MacBook Pro and the battery will not charge
When the magsafe adapter is connected. Has anyone else got this problem. N.B. The charging icon in the top right hand corner only displays the words (Not Charging)
I have been told by Apple Care to try a PRAM reset and a SMC reset, but the light on the mag safe never turns amber, just stay lit green.Hi...
At least try some troubleshooting before taking the Mac in... these are very easy procedures to follow.
Try here > Apple Portables: Troubleshooting MagSafe adapters
And definitely try Resetting the System Management Controller (SMC)
If that doesn't help, try Resetting your Mac's PRAM and NVRAM -
Updated my iTunes to the recent one and now it will not open on my MacBook Pro, got a new iPhone so tried to connect it and said i needed the new iTunes (which i did) and now i can't start my phone as i can't open iTunes which means i can't access anything on my phone!!?? HELP???????
You supply little pertinent about the MBP and the iPhone.
First... on the MBP... Click on the Apple icon.. Top left in Finder...
> About this Mac > Version...what does it say?
Which iPhone and what is its' iOS Version. -
I attempted to purchase the app Civilization V for my Macbook Pro, but the app will not download. How can I get the app to either finish the download or get refunded for the purchase?
Yuk, what a horrible app. But if you insist...
Mac App Store: How to resume interrupted downloads
http://support.apple.com/kb/HT4485 -
My Macbook pro and iPhone 4 will not pair.
I have gone through the setup assistant procedure numerous times, but always get the message "the pairing attempt was unsuccessful' on the Macbook Pro, and "pairing took too long" on the iPhone.
Any ideas?The wireless sync is by way of WiFi as opposed to BlueTooth. Tethering is the process of using your iPhones data plan to provide Internet access to another device, such as iPad or other computer. Tethering can be by way of WiFi, wired, or BlueTooth.
Stedman -
Yesterday I upgraded my MacBook Pro 13" (Early 2013) to 10.10.3. I immediately started having problems with it opening apps slowly. So I read and discovered it had replaced some of my apps with newer versions. I also restarted it 2 or 3 times. That seemed to solve that problem. This morning I get on and it is doing the same thing, but it is limited to the Calendar. Anything I try to do in the Calendar gets me the spinning beachball, from opening it to editing to adding an event. I have many dates and events saved that I don't want to lose. Am I going to have to reinstall the Calendar? If so, how can I do it without losing my content?
This is the note I sent to the other thread (Macbook is slow since OS X 10.10.3. I'm sorry. I hope this helps
I did not have a specific category that said "log list" once I got to "All Messages". It just showed "Log" so that is what I am sending you. The other thing is that the timestamp is 9:23:?? the next is 9:34:?? and the problem occurred at 9:32:??. So you are getting the log from 9:23 until it repeats.
Apr 13 09:23:49 -MBP com.apple.xpc.launchd[1] (com.apple.imfoundation.IMRemoteURLConnectionAgent): The _DirtyJetsamMemoryLimit key is not available on this platform.
Apr 13 09:34:43 -MBP hidd[96]: IOHIDEventQueue unable to get policy for event of type 11. (e00002e8)
Apr 13 09:34:47 --- last message repeated 83 times ---
Apr 13 09:34:47 -MBP spindump[1465]: Got xpc error message in libspindump client connection: Connection invalid
Apr 13 09:37:56 -MBP apsd[73]: Failed to initialize budgeting, not using budgeting: Error Domain=Timed out waiting for XPC and/or reply handler Code=104 "The operation couldn’t be completed. (Timed out waiting for XPC and/or reply handler error 104.)"
Apr 13 09:37:56 -MBP apsd[73]: apsd(73,0x7fff7a8d5300) malloc: *** error for object 0x7fd5e0c43ef0: pointer being freed was not allocated
*** set a breakpoint in malloc_error_break to debug
Apr 13 09:38:29 -MBP com.apple.xpc.launchd[1] (com.apple.Finder[221]): Service exited due to signal: Terminated: 15
Apr 13 09:38:29 -MBP kernel[0]: process Messages[57790] caught causing excessive wakeups. Observed wakeups rate (per sec): 115; Maximum permitted wakeups rate (per sec): 150; Observation period: 300 seconds; Task lifetime number of wakeups: 45001
Apr 13 09:38:29 -MBP com.apple.xpc.launchd[1] (com.apple.ReportCrash[57808]): Endpoint has been activated through legacy launch(3) APIs. Please switch to XPC or bootstrap_check_in(): com.apple.ReportCrash
Apr 13 09:38:29 -MBP ReportCrash[57808]: Invoking spindump for pid=57790 wakeups_rate=115 duration=392 because of excessive wakeups
Apr 13 09:38:29 -MBP com.apple.xpc.launchd[1] (com.apple.imfoundation.IMRemoteURLConnectionAgent): The _DirtyJetsamMemoryLimit key is not available on this platform.
Apr 13 09:38:29 --- last message repeated 1 time ---
Thank you for your times! -
I put a DVD into my MacBook Pro and the computer does not read it. what do I do?
I have a DVD with a bunch of home movies on it. When I put the DVD into my MAcBook Pro so it would burn to my computer, nothing appeared. It made a lot of noise but nothing happend to the screen. I need help!!
Try the DVD on a console DVD player or another computer. If plays, your super drive may need replacing. Just trying to diagnose what's not working
-
When trying to install downloaded software I am prompted to connect to the internet but I am already connected. This also occurs when trying to install an Adobe update.
A cable modem always needs a complete reset whenever you change the device that it is connected to.
To get your Internet signal restored, it will require at least one major step including the reset of your modem and complete network power cycle.
If that is not successful, the second major step is to reset the AirPort Extrreme back to factory defaults and then combine the steps above again.
Try this first:
Push the reset button on the cable modem (if present) and pull the internal batter (if easily accessible) then power off the modem
Power off everything else on your network....all devices....order is not important
Wait at least 20 minutes...longer will not hurt
Make sure that the Ethernet cable from the modem is connected to the WAN port (circle of dots or world icon) on the AirPort Extreme
Re-install the modem battery if it was pulled in the step above
Power up the modem and let it run for 4-5 minutes by itself
Power up the AirPort Extreme and let it run for 4-5 minutes
Power up each other network device one at a time about a minute apart until everything is powered back up
Check the network for proper operation -
I bought a second hand G4 iBook with iLife 09 on it. I have copied iLife to my new Macbook Pro. The applications would not open, so I did a software update and update all three applications, but they will still not open. Can anyone help?
The seller should have given you the original disk so that you can reinstall as needed. But it likely was a single-user license (which really means single computer) so you can only have a copy on one computer at a time. If the seller didn't give you the disk he is probably still using the software on his new Mac. Your best option to get any of the iWork apps to use in OS X 10.6.6 or later is through the Mac App Store. You can then install them on any Mac you have that has access to the Mac App Store using your Apple ID.
-
Thank you! This may sound lame but are these instructions for my blackberry? I'm receiving iCloud emails without problems on my MacBook Pro and I'd rather not mess w/ settings there. Thanks again!
You don't need to start a new thread to continue a conversation, you can just tack onto the original one. The settings I referred you to are for the Blackberry, since that's the device which is not receiving mail: anything which is working can be left alone.
-
MacBook Pro i5 with retina will not recognize WD Passport even though I successfully used it to transfer programs and files from my older MacBook ten days ago. It receives power from the USB, but when using Time Machine I receive the message that there is not an external device connected.
If the modem is also a router, either use the modem in bridge and run pppoe client on the TC.. that is assuming ADSL or similar eg vdsl. If it is cable service.. and the modem is a router, then bridge the TC.. go to internet page and select connect by ethernet and below that set connection sharing to bridge.
Please tell us more about the modem if the above gives you issues. -
I downloaded xbmc to my MacBook Pro and the application failed to quit and is not responding it is telling me to press continue to logout but the track pad is not responding what do I do?
Press and hold the power button until the machine turns off. Then restart.
Clinton -
I have a MacBook Pro and the batter icon has an "X" in it. I attempted resetting the SMC but it's still there. Not sure if the SMC didn't work or I have another problem. Help?
You can try the SMC again.
http://support.apple.com/kb/HT3964
Follow directions for a battery you should not remove yourself
You can also try a NVRAM/PRAM reset (at the bottom of the same page in the above link
Also hold the OPTION key and click on the Apple logo in the menu bar and click on system information, in the left column select power. Under the battery info see if it is charging (with the power adapter plugged in) as well as the health info (condition should be normal), and battery installrd (should be YES)
If other than these are different you may want to take it in to a Genius bar for a full diagnosis they will do that for dree.
Hope this helps -
I own Final Cut Pro 6 and have been running it on an older G4 tower. I upgraded to a MacPro tower and the app will not install. I get a message "Not supported on this computer" cannot believe this. Help anyone.
Here are the min. system requirements.... it looks like you meet them.... but I may have missed something...
Final Cut Studio 2 (Including Final Cut Pro 6)
• A Macintosh computer with a 1.25GHz or faster PowerPC G4, PowerPC G5, Intel Core Duo, or Intel Xeon processor
• 1GB of RAM
• An AGP or PCI Express Quartz Extreme graphics card (Final Cut Studio is not compatible with integrated Intel graphics processors)
• A display with 1024-by-768 resolution or higher
• Mac OS X v10.4.9 or Mac OS X v10.5.5 or later
• QuickTime 7.1.6 or later
Additional Recommendations
• 2GB of RAM when working with compressed HD and uncompressed SD sources
• 4GB of RAM when working with uncompressed HD sources
• A display with 1280 x 1024 resolution or higher
Additional Requirements for Motion
• A standard or built-to-order system configuration with a NVIDIA GeForce 5200, FX Go5200, FX 5200 Ultra, 6600, 6600 LE, 6800, 7300, 7300 GT, 7800, 7600 GT, 8600, 8800 or Quadro class graphics card.
• A standard or built-to-order system configuration with a ATI Radeon 9800, 9700, 9600Pro, 9600XT, 9700Pro, X800, X1600, X1900, or X2600 class graphics card; or a ATI Mobility Radeon 9700 or 9600 graphics card.
• For 16- and 32-bit rendering: a graphics card with at least 128MB of VRAM.
Additional Requirements for Color
• The standard graphics card in any Mac Pro, 17-inch MacBook Pro, 24-inch iMac, or 2.5GHZ or faster Power Mac G5 Quad:
• ATI Mobility Radeon X1600
• ATI Radeon X1600
• NVIDIA GeForce 7800 GT, 7600 GT, 7300 GT, 6800 Ultra DDL, 6800 GT DDL, 660, or Quadro FX 4500.
• For 32-bit rendering: a graphics card with at least 256MB of VRAM.
• A display with 1680-by-1050 resolution or higher (excluding 20" iMac); dual displays are highly recommended.
• A three-button mouse for full functionality
Apple article on Final Cut Studio 2: http://support.apple.com/kb/SP535 -
I have a macbook pro and the software with snow leopard only has upgraded to 10.5.8, do I need to purchase mountain lion to upgrade to 10.6.8?
Your machine likely can't handle Mountain Lion 10.8 nor 10.7, if it does it will run slow and very higly likely a lot of your third party software and drivers for printers and scanners won't function anymore.
It's because your 10.5 era (or earlier) machine is rather dated, hardware has advanced and is faster, the newer OS X versions have gotten bloated.
I do recommend you call Apple via phone and order the 10.6.3 white retail disks, backup your personal data off the 10.5.8 Mac to a external storage drive and when the disk arrives, stick it in and run the upgrade installer.
Once that's finished, reboot and use Software Update to get to 10.6.8 and stay there. You can buy stuff from AppStore, just don't upgrade to 10.8 (or 10.7) as thats when you'll have issues.
10.6 should run your currrently installed PPC software and hardware drivers. But 10.7/10.8 will not.
10.6 is receiving security and other updates from Apple as more than 50% of OSX users are still on it.
Most commonly used backup methods
Things to consider before upgrading OS X
Maybe you are looking for
-
Get the duration of all mp3 files inside a directory
Hello everyone, I am working on a little project done with swing. Since I need an mp3 player inside my swing application, I found a really good solution with JavaFX 2. I have never worked with JavaFX before, therefor it seems to me a little bit stran
-
Error message while creation of material for wrong warehouse no
dear all, i have assigned plant and storage location to warehouse no x,created the material for the same.our question is why the system is not showing warning or error message if we create the same material ,plant and stg location combination to a di
-
OSX 10.6.8 will not open or save PDF
I run OSX 10.6.8 safari 5.1.5 Adobe Reader 10.1.3. I have deleted plug-ins with ref to PDF. A black screen shows for any attempt to open a web PDF. This was not a problem until a few days ago. I have saved PDFs before
-
Cannot send mail through Windows Live Mail with 3rd party email address
I know this problem has been thoroughly discussed, and I basically understand it. I must change my outgoing port to 587 on my two non-Verizon email accounts that I pull into Microsoft Mail along with my Verizon mail. One of the accounts is my web si
-
I have not been able to find a satisfactory answer regarding Oracle 10g on VMWare. On one page, Oracle states that "Oracle will not support production deployments of Oracle software on VMware" (http://www.oracle.com/technology/tech/linux/vmware/cookb