Upgraded MacBook Pro to 10.8.5 but no longer detects any WiFi networks!
Was working just fine prior to today's upgrade from 10.8.4 to OS X 10.8.5 (12F37) - Serial W8*******71C
Wi-Fi: Looking for networks... does not look up any availanble networks home or usual suspects around me.
Software Versions:
CoreWLAN: 3.4 (340.18)
CoreWLANKit: 2.0.2 (202.11)
Menu Extra: 8.1 (810.11)
configd plug-in: 8.5 (850.252)
System Information: 8.3 (830.5)
IO80211 Family: 5.3 (530.5)
Diagnostics: 2.1 (210.25)
AirPort Utility: 6.3.1 (631.4)
Interfaces:
en1:
Card Type: AirPort Extreme (0x14E4, 0x8D)
Firmware Version: Broadcom BCM43xx 1.0 (5.106.98.100.17)
MAC Address: xxx
Locale: FCC
Country Code: X0
Supported PHY Modes: 802.11 a/b/g/n
Supported Channels: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 165
Wake On Wireless: Supported
AirDrop: Supported
Status: Off
<Edited by Host>
Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, or by corruption of certain system caches.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards. Boot in safe mode and log in to the account with the problem. Note: If FileVault is enabled on some models, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including sound output and Wi-Fi on certain iMacs. The next normal boot may also be somewhat slow.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin. Test while in safe mode. Same problem? After testing, reboot as usual (i.e., not in safe mode) and verify that you still have the problem. Post the results of the test.
Similar Messages
-
Upgraded iMac to 10.8.5 but no longer detects any WiFi networks!
I have a 2009 27" iMac and a 24" 2007 iMac with 2 Airport Extreme routers (2013 The latest.
Everything was working perfectly till I upgraded to 10.8.5.
I lost my internet and both routers. Could not use the Internet and Wi-Fi on my iPhone 5.
Reverted to a backup with 10.8.4 and everything is working perfectly as it did before the upgrade.
Does this mean that I will not be able to upgrade to 10.8.5 or 10.9 ???Troubleshooting Wi-Fi issues in OS X
Wireless Connection Problems - Fix
Wireless Connection Problems - Fix (2)
Wireless Connection Problems - Fix (3)
Wireless Connection Problems - Fix (4)
Wireless Diagnostics - About -
Hi Everyone. My MBP 7,1 didn't have any wifi issues not until 2 weeks ago. The laptop's battery got empty and when I tried to turned it on, the computer just froze. So I tried to reset it. However, I noticed that the wifi or airport can no longer detect any wifi signal. There were instances that it wouldn't turn on when I shut it off but now, it seems okey. I tried the zapping of PRAM and deleting all the things needed as I saw in different threads but it still not working. The ethernet works fine but I still need the wifi. Its been 2 weeks already. I don't have an Apple Store near me coz I am in southern part of Philippines. Can someone shed light on this? Thank you so much.
Hi!! To add more to the issue, the other day, my airport card is nowhere to be found. It now says no airport card installed which is really crazy. I also noticed that my MBP freezes during start up and I had to zap the PRAM so it would open up. Anyone there who experienced the same thing? I'd really appreciate your suggestions. Thanks!
-
I am transfering data to new macbook pro from pc. During transfer my pc shut down. I restarted the pc. The macbook pro is now stuck at the transfer stating 44 minutes remaining and is not doing anything. i tried a control, alt, delete???
Wait for the Mac to 'timeout' if an hour passes with no change press the power button on the Mac and hold it for 10 seconds.
Start the migration again when the Mac restarts. -
Macbook pro retina (1 month old) can no longer connect to Wifi
First of all I love my new mac, had no problems with it so far, and it's more than adequate for my requirements. However came to connect to my Mum's home network today (my iPhone and her windows desktop are connected right now so I know there's no problem with the ISP) and it won't connect, even though I've typed and re-typed the password a million times over. Was thinking initially she's changed the password without telling me, but I know that can't be the case because a) she's a technophobe and b) my iPhone wouldn't automatically connect (it was 3 months since the last time I was over). Then what struck me is last night I had similar issues round a friend's house where I've never connected before, but then so did he with his Macbook Pro (3 years old). However we reset the router and went to bed and this morning his worked fine; mine still nothing. The last time I succesfully connected to a network was on Friday, on the train down here, when I was tethering my iPhone's 3g connection. Could this be something to do with it? I've tried running network diagnostics several times but it never gets to the second stage as it can't connect to this network, which considering I'm using right now, I can assure you is running perfectly smoothly. The main error message I seem to be receiving both today and yesterday is 'connection timeout'. Is there a possibility I have somehow disabled my wifi connectivity? I can't seem to see where though. Having just purchased the mac I would've of course contacted applecare, but rather frustatingly they're closed on Sunday's and with a 3000 word report on HR Management that I need to finish today I can't afford to wait until 8am tomorrow, and I'd really appreciate some help beforehand so I don't have to complete my work on this ancient, virus-riddled pc!!
Many Thanks Folks!
Ryan, Norwich, UKBy Jove, after a couple of hours of stress I think I've just cracked it; I went onto System Preferences> Network> Advanced and then simply deleted a couple of networks I've connected to only once but won't need again and then it seemed to do to the trick. So it looks like you can only store upto 10 networks; I'm astonished it doesn't appear to say this anywhere in the manual!? Maybe it's too obvious and I'm an idiot for not already possessing this knowledge but come on, considering the box 'remember this network' is automatically ticked, surely this is a problem that your average user is going to experience rather frequently. How hard would it be for Apple to introduce an error message along the lines of 'maximum number of saved networks exceeded... Please delete one or more saved networks...'!? As for the applecare centre being closed, it would've been really useful if the sales rep could've mentioned this simple fix; It would have taken all of 10 seconds and would've saved me a lot of time and frustration.
It would be nice if this discovery helps others, but perhaps I should really be apologising for stating common knowledge. Well I guess the lesson here is what I already knew; the more you experiment with OS X the more you learn. Thanks to anyone who may have helped, back to the work now ....
Ryan -
Upgraded MacBook Pro 15in RAM to 12GB but still having problems.
Since I did the software update to OS X Mavericks around two weeks ago my MacBook has been on the fritz. After around an hour of use, everything freezes and my MacBook begins to beep. I read that the beeping code that I am hearing indicates an issue with the RAM. There are three beeps, a pause, then three more beeps. This continues untill I do a hard reset. I decided to upgrade my RAM from the standard 4GB that it came with to 12GB (8GB and 4GB) to see if that would resolve the issue. I installed the new RAM yesterday and my MacBook worked fine for the entire duration of use. This morning I turn it on and the issues began again after around 30mins of use. Can anyone help?
A little info on the model MacBook I'm using:
MacBook 15in Early 2011
OS X Mavericks 10.9.1
2 GHz Intel Core i7
12 GB 1333 MHz DDR3
Also, I dont know if it makes any difference but the RAM I upgraded to was purchased from crucial.com.Reseating means make sure they are installed and "seated" securly. Take them out and put them back.
You could also try running only one stick at a time. If one stick is bad that could isolate the problem.
And yes, purchasing from Crucial was a good idea. They provide Mac-tested and guaranteed RAM with a lifetime guratntee. If you find one of the sticks is bad they will replace it, no questions asked. -
I wish to upgrade my Macbook Pro to ML from SL but told the only way to do this is by downloading thru App store. Is it possible to copy ML on to a USB and upgrade that way. I would like to have a back up of the OS installation files just in case i have a problem later. Please help me!
You can create an install disc but you would have to download Mountain Lion to do so..
How to create an OS X 10.8 Mountain Lion install drive | MacFixIt - CNET Reviews
And make sure your Mac can upgrade to Mountain Lion.
See Step 1, 2, and 3, here > Apple - Upgrade your Mac to OS X Mountain Lion. -
I am running Facetime version 1.0.3 (167) on MacBook Pro OSx 10.6.8 but Facetime fails to other Mac devices. What version of Facetime can I upgrade to in order to rectify this ?.
Unable to make or receive FaceTime calls after April 16, 2014
-
I want to upgrade my MacBook Pro 5,2 to Lion, but specs says i need intel core 3 and i have intel core 2, there will be a problem? my computer will run slow? I will need to reinstall my programs again?
Hardware Overview:
Model Name: MacBook Pro
Model Identifier: MacBookPro5,2
Processor Name: Intel Core 2 Duo
Processor Speed: 2.8 GHz
Number Of Processors: 1
Total Number Of Cores: 2
L2 Cache: 6 MB
Memory: 8 GB
Bus Speed: 1.07 GHz
Boot ROM Version: MBP52.008E.B05
SMC Version (system): 1.42f4
Sudden Motion Sensor:
State: EnabledCheck to make sure your applications are compatible. PowerPC applications are no longer supported after 10.6.
Application Compatibility
Applications Compatibility (2) -
I am trying to upgrade my macbook pro to os x mavericks， but it has been on the reboot process for more than 2 hours. There is only the apple logo with the spinning ball thing. What should I do?
Hi there Candyleehoiman,
I would recommend taking a look at the troubleshooting steps found in the article below.
Mac OS X: Gray screen appears during startup
http://support.apple.com/kb/ts2570
-Griff W. -
My macbook pro (late 2008) shuts down but battery is at 25-30%
My macbook pro (late 2008) shuts down but battery is at 25-30% and I don't get a low power warning box before this happens. This only happens when the power chord is not connected, and it restarts with no problems once I put the power chord in. Does this mean I need a new battery, or is it an indication of something else? Using osx 10.5.8
Mine is Unibody 15" MBP late 2008, with the exact problem as yours. It can be a sudden shut down at 25-32%, or, after upgrading to OS 10.7.2, can be hang all of sudden on battery power.
Condition on, "Replace Soon". From 4.5 - 6 hours when new, goes down to 1 - 2 hours on discrete graphics.
But after 'abusing' it for the first year in the heat of Jakarta's climate in a non AC room when doing a video editing, before moving back to a comfort AC room at home sweet home, the battery performance is still top notch comparing to other kind than Apple. Also, it caused me to replace the right fan, after a lot of hard work on that first year. Oh, and by the way, I regularly done the battery calibration, at least once or twice between 3-6 months.
Here's also an useful link about battery I found on the internet:
http://batteryuniversity.com/learn/article/how_to_prolong_lithium_based_batterie s
My battery condition:
Battery Information:
Model Information:
Serial Number: 6N8389BD13EB
Manufacturer: SMP
Device Name: bq20z951
Pack Lot Code: 0
PCB Lot Code: 0
Firmware Version: 002a
Hardware Revision: 000a
Cell Revision: 100
Charge Information:
Charge Remaining (mAh): 2192
Fully Charged: No
Charging: Yes
Full Charge Capacity (mAh): 2716
Health Information:
Cycle Count: 616
Condition: Replace Soon
Battery Installed: Yes
Amperage (mA): 254
Voltage (mV): 12392
System Power Settings:
AC Power:
System Sleep Timer (Minutes): 0
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes): 15
Automatic Restart on Power Loss: No
Wake on AC Change: No
Wake on Clamshell Open: Yes
Wake on LAN: No
Current Power Source: Yes
Display Sleep Uses Dim: Yes
GPUSwitch: 2
PrioritizeNetworkReachabilityOverSleep: 0
RestartAfterKernelPanic: 157680000
Battery Power:
System Sleep Timer (Minutes): 10
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes): 5
Wake on AC Change: No
Wake on Clamshell Open: Yes
Display Sleep Uses Dim: Yes
GPUSwitch: 2
Reduce Brightness: Yes
RestartAfterKernelPanic: 157680000
Hardware Configuration:
UPS Installed: No
AC Charger Information:
Connected: Yes
ID: 0x0100
Wattage (W): 85
Revision: 0x0000
Family: 0x00ba
Serial Number: 0x0063ac36
Charging: Yes
Got the battery replacement today. Hopefully it will last for at least 3 years like it predecessor. -
HI, I just got a Macbook Pro. It's great but my mail doesn't work at all. It will come up correctly, but take forever to download messages, then won't delete them, then won't save them to folders. Then when I go to quit mail it's like it gets stuck between quitting and not. I have to force quit, then restart my computer if I want to pull up my mail again. How can I fix this?
If you just got your new MBP you have phone support from Apple (which is quite good) call them. 800-692-7753 tell the automated answerer "mail technical support" you'll have human quite quickly. Hope this helps.
-
My macbook pro and ipad does not recognize my printer on my wireless network, but my pc does. How can I get my apple products to see it on the network so I can print wirelessly? My printer is a Brother MFC-J270W
try disabling email scanning for incoming mail.
One of the last things that occurs is the mail server and Thunderbird sign off on "where we are up to" and Thunderbird stores this state information in the popstate.dat file in your profile (there is one in each POP mail account folder). If the anti virus, or you for that matter, end the conversation a few seconds early that hand off does not occur and the popstate is not stored. -
Can't get iCloud mail on my MacBook Pro. I used to, but not now.
I have been traveling, and using all sorts of servers to get my mail through the mail program on my MacBook Pro (Blue stamp icon). But now I am home, and the problem that started while over the road is continuing.
Under iCloud, the mail icon is checked. Under accounts, the only place blank is the IMAP Path Prefix. Port is 143, and SSL is checked. Authentication is Apple Token. Checked are also "include when automatically checking for new messages" and "compact mailboxes automatically"
Any help to get my mail up and running again?
Thanks in advance.You're going to have to give us more info than "I can't get net flix to work."
What have you done to try to get it to work?
Have you installed Silverlight?
Have you activated you Mac with NetFlix?
How are you accessing NetFlix? (Browser, Boxee....)
Exactly what is happening? -
Videos (eg, YouTube, New York Times) do not work on my Retina Display MacBook Pro. There is sound but only empty space where the video should be. Help?
Did you install Flash Player?
http://get.adobe.com/flashplayer/
Maybe you are looking for
-
Printing a year planner from ical
is it possable to print a sasco style calander from ical within lion .it apears to be able to print a silly colourd yellow to red chart showing how many events on a day but no descriptions i would love it to print it out in a month by month in a year
-
How to get Classes of Functional Location and Equipment
Dear Experts, I would like to know how to get all the classes in Classificaition of Functional Location and Equipement, FM ITOB_GET_CLASS_STANDARD is only get 1 class, how do I get all declared classes inside classification? Any table or FM? Thank yo
-
Where can I get the english keyboard shortcuts for Fireworks CS4? I have the french version installed and I when I read an english tutorial its way less complicated to follow with the english shortcuts. thanks
-
Relation between base page and detail page
I'm new to OA Framework. I developed a base page and detail relationship page and in the base page there is a button on clicking of that button, Detail page is rendering . but the related data with that button should come in the messagechoice box,whi
-
This the second time in the last few months this has happened. I spent an hour and a half last time with your tech support getting it up and running. I have not moved the software from the hard rice it has been on since CS4 came out. It's the same co