Upgraded to CUPS 8.5 - MP and VM not function ?

Hi ;
Currently just upgrade the customer CUPS from 7.0 to 8.5. It look good, but after that found out from CUPC server health the MP and VM shown in red, not able to communicate to MP server and Voice Mail. But for CUPC 7.x access to CUPS 8.5 no issue at all. All the CUPS configuration remain the same in 7.0 during upgrade to 8.5.
anybody come across for this issue ? Pls advice. Thanks.
rgds
tan

I can confirm the third USB monitor issue. I ran into it at another customer but they chose to just install a PCI Express card instead of working through it with TAC.
Most of the issues I have ran into have been video card driver related. CUPC uses DirectX and the release notes even say to make sure the latest driver is installed. If that doesn't fix it then you get to play Cisco QA with TAC.

Similar Messages

I have a 27" iMac with 16GB of factory installed SDRAM and 1T harddrive. It is telling me the harddrive is full and is not functioning correctly. How can I adjust so that all files are managed on the harddrive rather than the SDRAM. (BTW - design flaw)

Processor 3.4 GHz Intel Core i7
Memory 16 GB 1333 MHz DDR3
I have a 27" iMac with 16GB of factory installed SDRAM and 1T harddrive. It is telling me the harddrive is full and is not functioning correctly. How can I adjust so that all files are managed on the harddrive rather than the SDRAM. (BTW - design flaw here.)
Older Macs with a single Harddrive would simply expand OS management on the drive, and I think I understand the new Fusion Drive to do just that, but how do I get this product that I spent a great deal of money on to be more than a pretty screen?

I was confused by this statement
It is telling me the harddrive is full and is not functioning correctly.
OS X manages ram and when you run out, it create swapfiles to extend your ram on the HDD (Hard Disk Drive). The OS itself, takes about 16 gig of space and that too resides on the HDD. Your 16 gig of RAM is really a temporary space that holds things from the HDD so the processor can work on them. There is no design flaw between your ram and HDD. Something else is going on and there are a lot of smart people here to help you figure out what that "something else" is.
I would do three things. First I would create a backup, backups are important. Second, I would reboot into recovery and repair my HDD. Lastly while still booted in recovery I would repair permissions.
Can you capture a screen shot of the exact error you are getting?

Barge in and intercept not functioning in a CAD 7.5

I am presently working on a project which has UCCE setup with CAD 7.5 as agent desktop.We are running on 7.5(7) ICM and 7.5(8) CAD.I am facing a problem with Barge In and Intercept feature not functioning as expected.On a Barge In when the sup tries to barge on csd the caller is put on a hold and Agent desktop and Sup are connected.It needs to be completed from the phone and there is no direct conference established without the agent conferencing.With a Intercept again there is no direct transfer from the CAD to CSD and shows transfer cannot complete on the phone of the CAD.I am assuming there is no extra configuration for this and if my recording and Silent monitoring is working this should be quite simple.Am i missing anything here.The transfers and conferences at the telephony level are working fine.
I was facing the same issue on the base version and went with an upgrade but same problem.

Hi,
Did you check the applicaton log ?

Why are my firefox icons and tabs not functioning properly?

My firefox is not functioning properly since Monday. I have tried uninstalling and installing firefox but the problem is still there when I open it. Please help.

Unfortunately, the most likely explanation is an incompatibility with your graphics card/chipset driver software. One of the effects of Safe Mode is to disable Firefox from using hardware acceleration. To turn that feature off in normal mode as well:
"3-bar" menu button (or Tools menu) > Options > Advanced
On the "General" mini-tab, uncheck the box for "Use hardware acceleration when available"
This takes effect the next time you exit Firefox and start it up again. Any difference?

Keyboard and Mouse Not Functioning

Hello folks,
I have a T60. Once Windows loads up, the internal keyboard and mouse do not function. They function before Windows loads (in Bios config, etc.) and the keys to turn on the spotlight work. An external USB keyboard and mouse work perfectly.
As far as I know, this is completely random. It's driving me crazy.
Any help would be appreciated.
Thanks!
Chris

Chris, welcome to the forum,
did the advice in the other thread you posted in yesterday not help? There is a link to a possible solution in another thread here. You need to feed the boards with information; especially what you've tried, but didn't work - members get hungry
What happens in safe mode? Does the keyboard et al work as expected? Have you tried deinstalling them in safe mode through device manager and then restarting?
Thanks
Andy ______________________________________
Please remember to come back and mark the post that you feel solved your question as the solution, it earns the member + points
Did you find a post helpfull? You can thank the member by clicking on the star to the left awarding them Kudos Please add your type, model number and OS to your signature, it helps to help you. Forum Search Option T430 2347-G7U W8 x64, Yoga 10 HD+, Tablet 1838-2BG, T61p 6460-67G W7 x64, T43p 2668-G2G XP, T23 2647-9LG XP, plus a few more. FYI Unsolicited Personal Messages will be ignored.
Deutsche Community Comunidad en Español English Community Русскоязычное Сообщество
PepperonI blog

Firefox will not open some sites and does not function on those opened

Firefox does not open comcast.net and fails to respond on other websites. It opens others but does not function once opened.
== URL of affected sites ==
http://
== User Agent ==
Mozilla/5.0 (Windows; U; Windows NT 6.1; en-US) AppleWebKit/533.4 (KHTML, like Gecko) Chrome/5.0.375.86 Safari/533.4

I am an ordinary user and use FireFox on a Windows XP pro sp2 OS.
I can open and run FireFox by a variety of methods, and do not need to have any firefox: folders, files, or shortcuts on my Desktop unless I so wish.
I suspect you have a rather none standard installation. The quickest solution may well be to uninstall FireFox ( which you have presumably not been able to use anyway) and reinstall it. I would suggest; at least initially; you just use the standard default installation you are offered.
You will probably find this page of use, the [http://www.mozilla-europe.org/en/firefox/3.6.13/releasenotes/ Release Notes], it includes links for downloading FireFox, and has advice and information about installing and downloading.
I am sure you will have further questions when you try to install but click on the blue link above and look at that page and then post back again and I am sure someone will try to help you.
I am assuming that you are already on the Internet with a browser such as Internet Explorer, and a broadband connection, or are you trying to install from a CD or something that has a FireFox install file on it. (if so what are you using, and what is the version of firefox)

HT2584 why isn't my mac pro work properly as it is new. the connection for the bluetooth is totally out and its not functioning at all. kindly please assist me on this

THE BLUETOOTH CONNECTION IS NOT FUNCTIONING PROPERLY AND IT BEING DIFFICULT TO DOWNLOAD THE UPDATES

The standard first attempt at "fixing" BT problems is to do a smc and pram reset (try these first). But for mac pro's, if you are using a magic mouse say, about 3 or more feet, from the mac pro, you are most likely in for some continued aggravation. That's because the BT antenna is hidden in the back of the mac pro (faraday cage) and the magic mouse BT, for lack of better words, $ucks.
Here's a thread on this subject:
Poor Bluetooth reception and jerky mouse
Basically it comes down to wiring your own external antenna in place of the internal one already there or using a BT USB dongle. I use a dongle myself on my 2010 mac pro.

Slide to unlock has parallel lines and will not function

slide to unlock has parallel lines and will not function

Hello there, Jennings48.
The following Knowledge Base article offers up some great steps for troubleshooting issues with touchscreen response and links to additional information as well:
iPhone, iPad, iPod touch: Troubleshooting touchscreen response
http://support.apple.com/kb/ts1827
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro.

Webiste for printer set up is forbidden and will not function.

I need help, I bought this hp printer earlier this afternoon at pc world and i am now trying to set it up to my acer chrome book, and as these laptops don't have a cd/dvd space i have to enter the address www.hp.com/ePrint/ENVY4500... this will not work for me and says this website is forbidden, thankyou for listening, regards brian.

Hi , I see that you're experiencing issues downloading the HP Software for your HP ENVY 4507 e-All-in-One Printer. I would be happy to help you.
Which browser are you using? Try using another browsers like Internet Explorer, FireFox or Google Chrome. Click here: EN4500_198.exe, to download the Full Feature Software and Drivers for your HP ENVY 4500 e-All-in-One Printer.
How To Fix the 403 Forbidden Error:Check for URL errors and make sure you're specifying an actual web page file name and extension, not just a directory. Most websites are configured to disallow directory browsing so a 403 Forbidden message when trying to display a folder instead of a specific page is normal and expected.
Important: This is, by far, the most common reason for a web site to return the 403 Forbidden error. Be sure you fully explore this possibility before investing time in the troubleshooting below.
Tip: If you operate the website in question, and you want to prevent 403 errors in these cases, enable directory browsing in your web server software.
Clear your browser's cache. Issues with a cached version of the page you're viewing could be causing 403 Forbidden issues.
Log in to the website, assuming it's possible and appropriate to do so. A 403 Forbidden message could mean that you need additional access before you can view the page.
Typically, a website produces a 401 Unauthorized error when special permission is required but sometimes a 403 Forbidden is used instead.
Clear your browser's cookies, especially if you typically log in to this website and logging in again (the last step) didn't work.
Note: While we're talking about cookies, be sure you have them enabled in your browser, or at least for this website, if you do actually log in to access this page. The 403 Forbidden error in particular indicates that cookies may be involved in obtaining proper access.
Contact the website directly. It's possible that the 403 Forbidden error is a mistake, everyone else is seeing it too, and the website isn't yet aware of the problem.
See my Website Contact Information list for contact information for lots of popular websites. Most sites have support-based accounts on social networking sites, making it really easy to get a hold of them. Some even have support email addresses and telephone numbers.
Tip: Twitter is usually abuzz with talk when a site goes down completely, especially if it's a popular site. The best way to focus in on talk about a downed site is by searching for#websitedown on Twitter, as in #amazondown or #facebookdown. While this trick certainly won't work if Twitter is down with a 403 error, it's great for checking on the status of other downed sites.
Contact your ISP if your still getting the 403 error, especially if you're pretty sure that the website in question is working for others right now.
It's possible that your public IP address, or your entire Internet Service Provider, has been blacklisted, a situation that could produce a 403 Forbidden error, usually on all pages on one or more sites.Source- http://pcsupport.about.com/od/findtheproblem/ht/wrongurl.htm Please respond to this post with the result of your troubleshooting. I look forward to hearing from you. Good Luck!

My ipod states its disabled and will not function now ... please help

ipod states its disabled and will not work or allow me to reset from itunes? any suggesstions?

You are going to have to restore it. Scince itunes does not connect to ur ipod because its disabled you are gonna have to put your ipod in DFU mode. Basicaly u have to hold the power and home button atthe same time for 10 second then release power button and keep holding home button for about 15 seconds ( all this you do it while ipod is connected to the computer) if it works, itunes will detect ur ipod in recovery mode and will give you the option to restore it.

Download Helper, even with paid converter upgrade, gives "Invalid Capture File" errors and will not record audio, with "File Creation Error - Unable to rename/copy audio file" Error.

Download Helper Screen Capture worked to capture video if the default "no audio" option is active. But, no audio. The "speakers" or "microphone" audio options are confusing....the audio to be captured is from the video, so what do you choose? With either "speakers" or "microphone" selected, the captured file has poor audio and no video. Re-capture efforts (speakers) get "Invalid capture file error" and "File Creation error- Unable to rename/copy audio file"
The paid upgrade of "Converter" doesn't work.
Instructive documentation - not very good.
Suggestions - Need time delay between initiation of "Record" and starting the video to be recorded.
Could use timer tracking of the record process.
Are there operating system limitations? (Have Windows XP Pro)

That is an issue for the developer of that Download Helper.

Video Card upgrade.No Signal. Keyboard and mouse not functioning.

Hello all and thanks for reading!
To start off here are my specs.
HP Pavilion HPE h9-1130 Phoenix Desktop PC
Windows 7
So the change i made was i took out the 7670 (the pc came with)
and put in a new HIS 7870 Ice Q turbo.
As i boot up my pc i get no signal and no power to my mouse and keyboard.
I even sent back the GPU thinking it was defective but after i got sent a new one"
the problem is still there. Any suggestions ? Thanks for any help in advance..(

Hi,
Your machine should be enough power to run the card. Please check its manual and make the right connections - also refer on the following link:
http://www.hisdigital.com/un/product2-695.shtml
Hope this helps.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

9800 Torch - Keyboard and buttons not functioning

I have had a torch since October 2010 and just in the last 2 days it has stopped responding when using the keyboard or buttons.
When I pull the battery and reboot, I can use the touch screen to unlock, and then can go in to any item. Example:  open text, can scroll and find a test to view, tap it and open. I can then reply, forward delete with the screen options but once that is done I am now stuck in the text message. My only option is to pull the battery.
I can not make phone calls but can answer by sliding up the screen. When call is done I can not end just have to wait for other person to hang up.
I have checked for Water damage and there is none, the phone has not had a hard drop and the to sides are very solid (not loose).
I have upgraded the OS and this has still not fixed the problem; Please Help!!
Br,
RMSDC89

It really is more common than you think.
1. Remove the battery immediately!! Do not attempt to turn on your BlackBerry.
2. Let the device dry in a warm, dry place for 3 to 5 days* (see below)
3. DO NOT "check it each day" by placing the battery in. Leave it be to dry completely. This takes time. Replacing the battery to check it can only damage it more (moisture + electrical current = disaster).
3. If the device is warm after the drying period, allow it to cool to room temperature before placing the battery back in.
*Suggestions on drying your BlackBerry in a warm place (open, with the battery out):
Place the BB in a container of dry UNcooked rice, and then you might also place it in any of the locations mentioned below.
On top of any dry heat emitting electronic component: TV cabinet or CRT, LCD, cable TV/Satellite converter box or plasma monitor
On the dashboard of your car on a sunny day
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4   Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA   Display/Scan Bar Code

IPod Nano 7th gen - software update error and now not functioning

Hello,
I recently plugged an older 7th gen iPod Nano that I hadn't used in a while into my computer (Windows 7 operating system) and iTunes wanted me to let it update its software. I said 'yes,' not really thining anything of it, and as the software update was taking place, an 'unexpected error' occurred. Now my iPod will not turn on or respond or anything. It shut off while plugged into the computer and has stayed off and I am unable to get it to turn back on. It is totally dead, like the failed update somehow ruined my iPod.
The iPod itself was a little damaged - the LCD touchscreen was nonfunctioning due to water damage, and only displayed a white screen when on, but I could still 'shake to shuffle' and it would play all of my music just fine. Now the iPod will not work at all.
Is there anything that can be done or am I just out of luck here? Did the fact that the iPod was damaged have something to do with the failed update?
I'm kind of bummed 'cause the iPod still played my music perfectly....
Thanks for any help or insights anybody can give.

I should add 2 important points: 1) I have no trouble syncing with my PC, just in updating the nano software, and (2) Buried in some Apple reference I found mention of problems if the nano isn't formatted for a PC vs. Mac. It gives info on how to tell what the format is, but it's outdated (the menu choices are different). I believe it is already formatted for a PC because of an entry under Settings/About which says the Version is "1.0 PC". Tell me if I'm wrong. Also, it would help me if I knew the destination of the software download. Does it download directly to the Nano or to a temporary folder on my PC?

The Yahoo page do not open properly , data is clustered on the left of the screen and do not function

When opening the Firefox, browser my home page Yahoo is not loading properlly. It open but the data on Yahoo page is all cloged on the left side of the screen and do no show the data nor the icons work, and i cant access any information nor sites, do not respond or work the yahoo page..
It has happen before but within hours or the next day it open correctly withouth doing anything, but now is not working since yesterday .
I have window XP

Do you have any external cleanup software that might be clearing or corrupting the Firefox cache?
You can try these steps in case of issues with web pages:
Reload web page(s) and bypass the cache to refresh possibly outdated or corrupted files.
*Hold down the Shift key and left-click the Reload button
*Press "Ctrl + F5" or press "Ctrl + Shift + R" (Windows,Linux)
*Press "Command + Shift + R" (Mac)
Clear the cache and cookies only from websites that cause problems.
"Clear the Cache":
*Firefox/Tools > Options > Advanced > Network > Cached Web Content: "Clear Now"
"Remove Cookies" from sites causing problems:
*Firefox/Tools > Options > Privacy > Cookies: "Show Cookies"
Start Firefox in <u>[[Safe Mode|Safe Mode]]</u> to check if one of the extensions (Firefox/Tools > Add-ons > Extensions) or if hardware acceleration is causing the problem (switch to the DEFAULT theme: Firefox/Tools > Add-ons > Appearance).
*Do NOT click the Reset button on the Safe Mode start window.
*https://support.mozilla.org/kb/Safe+Mode
*https://support.mozilla.org/kb/Troubleshooting+extensions+and+themes

Upgraded to CUPS 8.5 - MP and VM not function ?

Similar Messages

Maybe you are looking for