Upgraded to TimeCapsule and now issues with AirPrint from iPhone and iPad

Okay. I bought a HP 210a air print printer. It was working great with my Linksys router and my iPad and iPhone worked with it perfectly. Since that time I have recently bought a new new 2TB Time Capsule and just recently set it up. The old router is no longer hooked up. Since switching over to the new router, nothing prints from the iPhone or iPad. So here are the details and I am hoping I am just missing a step:
1. I think it is important to point this part out. After setting up the new router, and before discovering any of this, I turned on the HP printer. Upon doing so, the printer informed me a software update was available from HP so I downloaded it and it appeared everything was fine.
2. After the update, I tried printing and nothing. Duh, the printer was still looking for the old router. I ran the built in HP wireless setup wizard on the printer and it pointed to the new router fine. I tested the connection using the test feature on the printer, and it printed a report that all was fine and that it was now pointed at the Time Capsule, great signal, etc...
3. I went to my iPhone and iPad, made sure they were pointed at the same network as the printer, and once again the printer appeared on each device as an AirPrint printer. Great I thought, so printed a test a page from each device. Both pages printed. Now here is where it gets weird.
4. I tried to print a second document from the iPad and iPhone, nothing. I tried a picture. Nothing. It still shows eveything setup correctly, the HP shows as the AirPrint printer and connected, but no matter what I do, it nothing is printing from either device. I've tried resetting my network settings on the iPhone and iPad and pointing to the network again, re-running the HP setup Wizard on the printer. They all show that everything is fine. The iPhone and iPad connect to the network fine, both show the printer when I go to print. However, after I hit the "print" button on either device, it shows like the document is being sent but NOTHING happens on the HP. It is very frustrating.
The WiFi is working fine, I can surf, email, etc... so the router is working properly. So what am I missing? Could the HP update somehow have caused the problem? I have to believe that between the update and the new router that somewhere I am missing a step. Any help is greatly appreciated.

If that doesn't work, try power cycling your router, printer, and your iPad/iPhone in that order. To do this, follow these steps:
Unplug the router and printer from the power and shut off the i-devices. Let them sit for about 30 seconds and then plug just the router in.
Once the router is completely back online (usually takes about 30-60 seconds) plug the printer in. Wait until it is back on its home screen.
Turn the i-devices on.
Try to print again.
Let me know if this helps!
If I have solved your issue, please feel free to provide kudos and make sure you mark this thread as solution provided!
Although I work for HP, my posts and replies are my own opinion and not those of HP.

Similar Messages

Is there an issue with Safari in Iphones and Ipads where it does not recognize option disabled="disabled" tag properly?

Greetings everybody,
I have run into a peculiar problem with the Safari browser on mobile platforms (IPad, IPod, IPhone) which I hope I can find a solution for in this community.
I just launched a new website where I sell products with certain variations, for example please view this link: http://www.finerribbon.com/aegean-single-face-satin-ribbon.html
On this particular product, the product variants are supposed to work in such a way where:
If you select the value "1/8" from the "Choose Ribbon Width" field
THEN
The only options active and available to choose from in the "Choose Roll Size" field should be: 500 Yds, 20 Yds & Sample Swatch
Now, if we browse to the above link in Safari using a desktop or a laptop, there are no problems at all, but if we browse to the above link using an IPhone or an Ipad, then we have a problem where all the options are available regardless of the values chosen, basically the above functonality does not work.
I was told that there an issue with Safari in Iphones and Ipads where it does not recognize option disabled="disabled" tag properly, is this true? Can anyone advise me if there is a solution to this problem? I would sincerely apperciate it.
Thank you very much for your time and help!

Hi...
I have run into a peculiar problem with the Safari browser on mobile platforms (IPad, IPod, IPhone) which I hope I can find a solution for in this community.
Now, if we browse to the above link in Safari using a desktop or a laptop, there are no problems at all, but if we browse to the above link using an IPhone or an Ipad, then we have a problem
At the top of this window you'll see the following:
Apple Support Communities > Mac OS & System Software > Safari > Discussions
This the Safari forum for the Mac OS X.
Better that you post your topic here > Developer Forums: Apple Support Communities
I do see on my iPad what you are rreferring to. But you shoudl get the feedback you need in the developer forum.

HT4623 I have the latest iTunes software on my iMac mini and now have IOS7 on my iPhone and now I cant sync music from my library either by wifi or by usb?

I have the latest iTunes software on my iMac mini and now have IOS7 on my iPhone and now I cant sync music from my library either by wifi or by usb? I get song lists that scoll at a million miles an hour but no actual content. What should I do to get my music onto my iphone.

Here is what worked for me:
My usb hub, being usb2, was too fast. I moved the wire to a usb port directory on my pc. That is a usb1 port which is slow enough to run your snyc.

HT3204 I was in the process of restoring my ipad and an issue with itunes came up and itunes closed. Now my computer doesn't recognize the ipad as anything so I can't complete the restore process.

I was in the process of restoring my ipad and an issue came up with itunes and it had to close. I reopened itunes but now my computer doesn't recognize the ipad as anything plugged in to my computer. I am unable to complete the restore process.

Hi kimbo934,
Welcome to the Support Communities!
The article below may be able to help you with this.
Click on the link to see more details and screenshots.
iOS: Device not recognized in iTunes for Windows
http://support.apple.com/kb/TS1538
I hope this information helps ....
Happy Holidays!
- Judy

MBP issues with waking from sleep and on opening lid

I have a 2009 macbook pro just 3 weeks old! upgraded from an older macbook
the problem is when it goes to sleep mode and i wake it by opening the lid or pressing any key (trackpad clicking wont wake it) the curser is unresponsive, as are all of the keys apart form the power button - it brings up the box asking if i want to shut down or restart. But I cant choose any as no curser movement! so I have to hold in the power button to hard restart everytime.
I rang apple support who I must say are very helpful everytime. I reset the PRam, reset factory settings ect then he said if still no joy reinstall the system.
All of which I have tried and it is still doing the same problem.
I shall have to give them a call in the morning to see what else they suggest.
Has anyone else had this issue on a new macbook - all updates have been installed and I only use it for web and emails ect so no weird installs going on
Thanks in advance
Liz

still no joy, did a reinstall of the OS and its still intermittently not waking once i close the lid and the hard drive stops.
The next thing to do is to get apple to have a look at it. very annoying as I have only had it since 28th Dec but nothing else I can do. Pc world will have it in to fix rather than replace so to be honest I'd rather Apple had a look than some monkey boy with fat clumsy fingers on a YTS scheme lol

I have downloade itunes 10.5.1 and now can't sync my iphone or ipad. It does recognise any devices

I have downloaded Itunes 10.5.1 It refuses to recognise my iphone or ipad to sync.
I have reloaded it and restarted my pc but nothing changes..
Any ideas?

I had a similar issue on Vista and started researching this after being unable to sync my iPhone4 or access the iTunes Store after upgrading iTunes and Safari. Found a thread here that gave me the tip to uninstall ALL Apple software and then reinstall it all. This includes QuickTime, Application Support, Mobile Device Support, Bonjour, etc. You can find all this in the "programs and features" control panel (or whatever the Win7 version of it is). It will even let you uninstall there.
I tried uninstalling and reinstalling (and burning about 3 hours in the process) all the software I had uninstalled. However, after I had installed iTunes and before I installed Safari, I started iTunes to see if I could access the iTunes Store and I could!
Well, I thought I was on my way to full syncing and iTunes Store browsing pleasure..."must have been a bad install" I said and promptly reinstalled Safari as well.Once that was done, I started up iTunes and was met with the same blank iTunes Store screen, and was unable to sync my iPhone. Sigh.
So - uninstalled all Apple software again and resinstalled JUST the iTunes package. This time around, full success with iTunes Store and iPhone syncing!
Obviously, a browsing engine/rendering failure on the part of Safari that doesn't impact the browser in iTunes until Safari is installed.
1. Uninstall all Apple software
2. Reinstall ONLY iTunes package
3. DON'T reinstall Safari

Used Airplay and now no audio coming from Hulu and Netflix apps on Apple TV

I was watching a show on Hulu through Apple TV while looking at facebook on my iPhone. I'd forgotten to turn the Airplay off on my iphone and a friend's facebook video played on my tv. When it was over I tried to return to my Hulu show, but no audio was playing. I tried the Netflix app and no luck there either. I've turned both my phone and my apple TV off and on and nothing is working. It's definitely not a problem with my tv set. Can anyone help me fix this??

It's happened to me even when using airplay for a video that is not in FB. I reset ATV and it works once and then the audio disappears again. I'm considering using the ATV for a coaster.

1.3.5.1 Updated, and Now Issue With Incoming Calls

Since updating to 1.3.5.1, any time I mute the ringer on an incoming call, it mutes the ringer until right before the missed call notification, but then plays the ringer again briefly. This defeats the purpose of being able to mute the ringer in the first place.
Post relates to: Pre p100eww (Sprint)

This occurrs any time I press the volume rocker key to mute the ring of an incoming call. After the initial time when it played an extremely brief snippet of my ringtone (factory installed "Older Phone" ringtone), it has randomly switched between the short ringtone and a electronic squeal noise.
Since I know the slightest software change can kill a seemingly unrelated feature, I'll try to be as detailed as possible. For my phone setup, it is completely stock (phone no.5 after misc. slider/screen/charger door issues, haven't had time to change anything yet) My ringtone volume is set to maximum with vibrate also on, system sounds are also set to maximum with the default tone. I have no non-app catalog programs or patches installed. I use a Touchstone back cover, although the phone was not on the charger when I noticed the issue.
The only downloaded apps on the phone are Pandora, Tip 'em!, Stop Watch, Fandango, Good Food, Mileage Monitor and gDial Pro (which has not been set up yet). With the exception of Pandora, none of these apps have been used since I received this replacement phone. They were all just automatically downloaded because my previous phone had them. I have e-mail accounts through Cox, Yahoo, and Gmail, none of which are synced to contacts, calendars, messaging or tasks. I do have my Palm profile and EAS through my work in a full sync capacity.
Hope this helps.
Message Edited by kx250ryder on 01-07-2010 07:29 AM
Message Edited by kx250ryder on 01-07-2010 07:30 AM

PSE13 and Revel issues with the notes filed and date/time when syncing.

I extensively use the notes field in PSE13. For photos and videos this seems to get over-written when synced to Revel. For photos I can recover it by selecting 'Update Thumbnail' but during the next sync it over-writes it again.
I also have some files where the date / time are changed when syncing with Revel, particularly video files.
Any ideas?

I also have this problem. The time of my iPod always changes back to the time and date of my last restore every time I sync it. And I know of others with this problem also. Perhaps it is possible that your iPod and mine have been "configured" in a way that causes this issue?

Issue with Find My iPhone and Push settings

OK...I have three iPhone 4's and an iPad (all with the latest updates). All but one of the iPhones will allow Push. The advanced settings only give me an option for manual or fetch. Therefore, I can not set-up Find My iPhone on the one phone (although working fine on the other devices). I've tried everything: signed up for "me" account, changed passwords, deleted all other mail accounts, deleted and reset up me account, etc. The settings are identical in every way to the other phones, but still no luck. OK...the last bit of info...it did work when we first bought it, but my daughter deleted the mobile me mail account because she didn't know what it was (yeah right). But since then...nothing!

Thanks, but I have added it back (several times) and there is still no "push" under advanced settings, just manual and fetch.

Performance and Graphical Issues with iOS 4.3 and IPod Touch 4th Generation

My Ipod touch is only a week old and I just updated it to iOS 4.3 from the original firmware, but after I updated the device it seemed to start generating white lines in the status bar area unexpectedly. Then at the same time my device would stop responding for a couple of seconds or become extremely slow. I also notice that my album art is misplaced and/or obscured and nothing is misplaced on iTunes. I've restored it two to three times. The device can not be downgraded so I'm not sure what to do.

Hmmmm... you know what... some of my album art was misplaced also... mainly for my "Unknown Artists" but still... Oh yeah and everyone knows about the glitch on the top bar, theres a post with about 20,000 views on it so maybe you should check there

IPhone Gmail Issue With Deleting From iPhone

When I delete an email on my iPhone it disappears from my Gmail inbox but is still searchable and not deleted permanently from Gmail. Any ideas on how to permanently delete it from GMail from the iPhone?

Here is what it looks like on my iphone...
After selecting the gmail account I see
   account ([email protected])
   Mail (on off)
   Calendars (on off)
   Notes ( on off)
Archive messages (on off)
Did you set up your account on the phone as a Gmail, or as an imap?

Security issue with unlocking my iPhone 4?

I'm not sure if anyone here will be able to help me but I am trying to get my iPhone unlocked with AT&T. I bought my iPhone on contract through AT&T in December 2010. My account is in good standing. I paid my ETF, it's technically eligible to be unlocked. I called AT&T on April 9th for an unlock and it's now April 19th and still no wordd from them. I've called several times and they won't tell me what's going on other than that "there is a security issue with unlocking my iPhone and the issue is with Apple, but they are working on it." From my understanding, all AT&T needs is the unlock code to enter into the system and unlock it from there. I don't know what security issues could possibly exist that would create a problem. The only thing I can think of is that when I orginally bought my iPhone it turned out to be a lemon and had to get it replaced the day after I bought it. I did this through an Apple store since it was around Christmas. The IMEI number on my phone doesn't match the one AT&T has on file, but that shouldn't matter? I gave them the right IMEI number that is on my current phone. Does anyone know what "security issues" can exist when it comes to unlocking an iPhone 4?

Don't stress over the words used by the customer service people at AT&T. Half of them don't know what they're talking about more than half the time. You are probably correct in that it has something to do with their database being inaccurate.
Give it a few days, then contact them again and ask for it to be escalated.
Ignor rNair. The idea that Apple made it mandatory for AT&T to do anything is complete and total bunk. (S)He has no idea what (s)he's talking about

I have been having issues with not receiving texts and voicemails daily, for a few months now. If I turn the phone completely off, when I turn it back on the messages will flood in from hours before. I can't be continually turning off my phone in case som

I have been having issues with not receiving texts and voicemails daily, for a few months now. If I turn the phone completely off, when I turn it back on the messages will flood in from hours before. I can't be continually turning off my phone in case someone left me a message. How do I resolve this issue?

Wifi: my Cell phone will remember 10 wifi connections. So delete any you don't use often and your home wifi and try to enter home wifi again.
if it still won't connect to home wifi, call your internet provider for help. You may need a newer router or different settings Or upgraded service. Your phone seeks the best connection and will refuse lesser connections.
last resort. Backup the phone. Do a full reset, then restore as new with the backup.
if still not fixed, go back to apple and insist on repair or replacement.
HOWEVER. voicemail is not a wifi issue, it's a carrier function, which is why the SIM card is a suspect.

SP1 for Exchange 2013 install fails with ECP virtual directory issues and now transport service won't start and mail is unavailable

SP1 for Exchange 2013 install failed on me with ECP virtual directory issues:
Error:
The following error was generated when "$error.Clear();
          $BEVdirIdentity = $RoleNetBIOSName + "\ecp (name)";
          $be = get-EcpVirtualDirectory -ShowMailboxVirtualDirectories -Identity $BEVdirIdentity -DomainController $RoleDomainController -ErrorAction SilentlyContinue;
          if ($be -eq $null)
          new-EcpVirtualDirectory -Role Mailbox -WebSiteName "name" -DomainController $RoleDomainController;
          set-EcpVirtualdirectory -Identity $BEVdirIdentity -FormsAuthentication:$false -WindowsAuthentication:$true;
          set-EcpVirtualdirectory -Identity $BEVdirIdentity -InternalUrl $null -ExternalUrl $null;
          . "$RoleInstallPath\Scripts\Update-AppPoolManagedFrameworkVersion.ps1" -AppPoolName:"MSExchangeECPAppPool" -Version:"v4.0";
        " was run: "The virtual directory 'ecp' already exists under 'server/name'.
Parameter name: VirtualDirectoryName".
Error:
The following error was generated when "$error.Clear();
          $BEVdirIdentity = $RoleNetBIOSName + "\ECP (name)";
          $be = get-EcpVirtualDirectory -ShowMailboxVirtualDirectories -Identity $BEVdirIdentity -DomainController $RoleDomainController -ErrorAction SilentlyContinue;
          if ($be -eq $null)
          new-EcpVirtualDirectory -Role Mailbox -WebSiteName "name" -DomainController $RoleDomainController;
          set-EcpVirtualdirectory -Identity $BEVdirIdentity -FormsAuthentication:$false -WindowsAuthentication:$true;
          set-EcpVirtualdirectory -Identity $BEVdirIdentity -InternalUrl $null -ExternalUrl $null;
          . "$RoleInstallPath\Scripts\Update-AppPoolManagedFrameworkVersion.ps1" -AppPoolName:"MSExchangeECPAppPool" -Version:"v4.0";
        " was run: "The operation couldn't be performed because object 'server\ECP (name)' couldn't be found on 'DC0xx.domain.com'.".
Error:
The following error was generated when "$error.Clear();
          $BEVdirIdentity = $RoleNetBIOSName + "\ECP (name)";
          $be = get-EcpVirtualDirectory -ShowMailboxVirtualDirectories -Identity $BEVdirIdentity -DomainController $RoleDomainController -ErrorAction SilentlyContinue;
          if ($be -eq $null)
          new-EcpVirtualDirectory -Role Mailbox -WebSiteName "name" -DomainController $RoleDomainController;
          set-EcpVirtualdirectory -Identity $BEVdirIdentity -FormsAuthentication:$false -WindowsAuthentication:$true;
          set-EcpVirtualdirectory -Identity $BEVdirIdentity -InternalUrl $null -ExternalUrl $null;
          . "$RoleInstallPath\Scripts\Update-AppPoolManagedFrameworkVersion.ps1" -AppPoolName:"MSExchangeECPAppPool" -Version:"v4.0";
        " was run: "The operation couldn't be performed because object 'server\ECP (name)' couldn't be found on 'DC0xx.domain.com'.".
!! And now transport service won't start and mail is unavailable !!
Any help would be appreciated.
I have removed the ecp site from default site and attempting to rerun SP1 now. I do not have high hopes. :(

Hi,
Thanks for your response.
From the error description, you need to manually remove the ECP with IIS manager in both the Default Web Site and the Exchange Back End firstly. And then continue the upgrade to check the result.
Hope this can be helpful to you.
Best regards,
Amy Wang
TechNet Community Support

Upgraded to TimeCapsule and now issues with AirPrint from iPhone and iPad

Similar Messages

Maybe you are looking for