Upgrading Autonomous to controller-based (AIR-SAP2602I)

Hello,
I don't know if coul possible upgrade an SAP2602i Autonomous access point to controller-based?
Thanks in advanced for your help.
Regards.

I don't know if coul possible upgrade an SAP2602i Autonomous access point to controller-based?
Yes, it's very easy to convert an autonomous AP into controller-based.
All you need to do is download the controller-based recovery image (filename contains the "rcv"), copy the IOS into the AP and change the bootstring of the AP to boot the "rcv" file.

Similar Messages

Converting air-sap2602i-s-k9 from autonomous to LWAPP

Hi guys,
    I need your expertise regarding how to convert from autonomous to LWAPP using AIR-SAP2602i-s-k9 with IOS version of ap3g2-k9w7-xx.152.-2.JA.
    I'm following these commands but it is not available
    debug capwap console cli or debug lwapp console cli
I cannot proceed to convert it Did I miss something or the 2600 series doesn't support LWAPP convertion ?
thank you
Erik

Hi Erik,
Those commands aren;t going to work, they're debug commands for a lightweight AP.
Here is the guide to upgrading:
http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html
It's pretty simple though, get the lightweight software follow the upgrade tool instructions to load new software.
Though, you have a newer AP so you'd be ok just to load the new software on, if it's only for a small amount this is fine.
Thanks
Chris

Can AIR-SAP2602E/I-C-K9 convert to controller based AP?

Can AIR-SAP2602E/I-C-K9 convert to controller based AP?
both S2G1K9W7-15202JA/ JB available?

here are the procedure:
https://www.youtube.com/watch?v=wWDrFjwVNb0
http://rscciew.wordpress.com/2014/05/07/access-point-conversion-lap-to-aap-and-vice-versa/
Regards

Is AIR-OPT60-DHCP available on autonomous AIR-SAP2602I access point?

Hello Wireless Experts,
I was able to order AIR-OPT60-DHCP on controller based AP AIR-CAP2602I-E-K9 using CCW, but this option is not available on autonomous AIR-SAP2602I access points.
Is AIR-OPT60-DHCP available on autonomous AIR-SAP2602I access point?
Thanks.
George

That is a feature and only used in lightweight access points. The standalone autonomous access points don't use that. Just follow the configuration guide for your access point to get you started.
Sent from Cisco Technical Support iPhone App

How Convert AIR-AP1262-C-K9 standalone AP to controller based AP?

How Convert AIR-AP1262-C-K9 standalone AP to controller based AP? Is that possibe ? how?

Hi,
First follow these steps to convert to LAP:
http://rscciew.wordpress.com/2014/05/07/access-point-conversion-lap-to-aap-and-vice-versa/
WLC Model: Its all depneds on your requirement.
Its a small enterprize then go for 2500 series otherwise go for 5500 series.
Regards
Dont forget to rate helpful posts

After recent upgrade to Yosemite on Macbook air bluetooth audio cuts out and associated video stops with audio. Likewise with airplay and Apple TV. I have deleted all my saved wifi connections and restarted numerous times. I do not expect a resolutio

After recent upgrade to Yosemite on Macbook air bluetooth audio cuts out and associated video stops with audio. Likewise with airplay and Apple TV. I have deleted all my saved wifi connections and restarted numerous times. I do not expect a resolution from the community, but hope to get the attention of Apple engineers. If you are having same problems or have a miracle cure I am all ears.

May start my own thread, but I'm having similar issues.
I've been using an old iMac (running 10.7.5) and Apple TV for years with no issues. Last week I bought a new Macbook Pro running Yosemite and have had audio issues multiple times. The weird thing is that sometimes it works flawlessly, other times (like now) I spend half an hour just trying to get a song to play.
My issues are: When I got to "computers" in Apple TV to stream my music, my music is sometimes chopper or intermittent, and I seen to know when it's going to happen based on the status wheel just before it plays. When I choose a song, the status wheel will spin for an unusually long time, usually an indicator that the audio is either not going to work, or stutter.
When it does finally pull up a song, the playhead sits at the beginning of the song for a good 3-5 seconds before actually playing. Then, when it starts playing, it's all downhill. It will play a few seconds, drop out, play a few more seconds, drop out, and then ultimately the playhead will keep moving across the song as if it's playing, but there's no audio.
Again, this is a new phenomenon never experienced by me. I've tried everything I could think of, some of them all at once:
• restart Apple TV
• restart Macbook Pro
• quite iTunes/open
• turn off Home Sharing on iTunes then reconnect it
• unplugging and cycling both my modem and router
None of these have alleviated the problem.
The odd thing is, like this morning, the audio started up perfectly and never gave me any issues. It wasn't until later in the day that it started. Perhaps after the macbook pro had been put to sleep? Not sure.
Regardless, this is an annoying trait, one that's new to me and my system (as stated, worked flawlessly until my new purchase), and is 100% limited to either a) the macbook pro b) Yosemite or c) both of them.

After upgrading to Lion, my Macbook Air's built in iSight camera has disappeared. I'm not sure how to get it recognized again.

After upgrading to Lion, my Macbook Air's built in iSight camera has disappeared. I'm not sure how to get it recognized again. Help -Sami

Well, if you did then you may be able to track it, if you did not it's not possible.

After the recent upgrade to ios 8 ipad air has no audio coming out

HI
After the recent upgrade to ios 8 ipad air has no audio coming out

I had the same problem until tonight. Played with ring tones, do not disturb, volume, and everything else posted. What I found is that when you go to sounds/text tone, there are two types of tones in the scrolling menu. The top set of tones are for alert tones and the bottom set are ringtones. They are separated by a gray bar that states their purpose. Many of the tones are the same name. You need to set your text alert in the Ringtones and reminders, alarms, and such in alerts. The weird thing about this menu is when you go to sounds/ringtone the menu is reversed. Mine works in locked mode or unlocked now. I have an Iphone 6 8.1.2. My problem started after my latest OS upgrade. Hope this helps.

I need to upgrade my first generation Macbook Air to Lion OS x10. I need to install software that requires 10.7 also a java update that requires 10.7. I am currently on Snow Leopard 10.6.8 and my macbook Air 1.1 will not go up to Mountain Lion. The lion s

I need to upgrade my first generation Macbook Air 1,1 to Lion OS x10. I need to install other software that requires 10.7 also a java update that requires 10.7. I am currently on Snow Leopard 10.6.8 and my macbook Air 1.1 will not go up to Mountain Lion. The Lion software update 10.7 is no longer available from the store or downloads.
Where do I get this?
It was only released a couple of months ago.
I really feel disinfranchised already by not being able to upgrade and keep up with other software needs but to not allow me to update to my full capacity is really ridiculous.

@Jennacide wrote:
It was only released a couple of months ago.
OS Lion was released 16 months ago... in July 2011.
Lion Tech Specs > http://support.apple.com/kb/SP629
To upgrade to Lion...
Contact Apple in your Country to Purchase a Snow Leopard Disc...
http://support.apple.com/kb/HE57
In the US...
1-800-MY-APPLE or 1-800-676-2775
After the Successful Install, run Software Update to get the latest updates...
Be sure to make a Backup of your Current System Before Upgrading...
Also... Check here for compatibility of 3rd party Software you may be using...
http://roaringapps.com/apps:table

Download and upload speed per ssid in air-sap2602.

Dear team,
How to limit the download and upload speed per ssid in air-sap2602 ?
SSID =5MB download + 1upload
SSID= 30MB download + 5upload
Regards

If you need help with traffic shaping, you should post your question on the rLAN, Switching and Routing forum:
https://supportforums.cisco.com/community/netpro/network-infrastructure/switching
You can also look for examples by searching Configure 1941 traffic shaping:
http://www.cisco.com/en/US/docs/ios/12_2/qos/configuration/guide/qcfgts.html
http://www.cisco.com/en/US/docs/ios/12_2/qos/configuration/guide/qcfcbshp.html
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered"

ACL on controller-based wireless

We're trying to put an ACL on our wireless guest subnets on a controller-based wireless system. We're using 2 of the WiSMs. The ACL I used to use in WLSM allowed the guest subnet to the dhcp servers and out to the internet and dropped everything else, but I don't know where I would apply that list now for it to work with all the different vlans and addresses for the WiSMs.

Hi Brian,
Perhaps this doc will help;
ACLs on Wireless LAN Controller Configuration Example
From this doc;
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a00807810d1.shtml
Hope this helps!
Rob

HTML-based AIR app with transparent UI, shadows, etc.?

I'm debating on whether to use Flex or HTML/Ajax for a widget
in a project. If I make an HTML-based widget, is it possible to
have UI tricks like shadows and transparency, basically, NOT being
confined to a standard OS "box" window? Is this possible?
Thanks.

Yes it is possible to do this with an HTML-based AIR app.
However, since the visual elements will be HTML-elements, not
display objects, you can't use the Flash APIs for shadows and
transparency. Also, in a transparent window, SWF and PDF content in
HTML cannot be displayed.

Cisco AIR-SAP2602I

I'm trying to deploy a WiFi solution for a client. It would consist of 2 SSIDs; one for internal users with internal network access and a guest with only internal access.
I have a Sonicwall TZ215:
External IP: x.x.x.x
LAN IP: 192.168.1.1/24
DHCP Server: 192.168.5-195/24
+++++++++++++++++++++++
Cisco SG500:
v1.3.0.62 / R750_NIK_1_3_647_260
CLI v1.0
set system mode switch queues-mode 4
file SSD indicator encrypted
ssd-control-start
ssd config
ssd file passphrase control unrestricted
no ssd file integrity control
ssd-control-end cb0a3fdb1f3a1af4e4430033719968c0
voice vlan oui-table add 0001e3 Siemens_AG_phone________
voice vlan oui-table add 00036b Cisco_phone_____________
voice vlan oui-table add 00096e Avaya___________________
voice vlan oui-table add 000fe2 H3C_Aolynk______________
voice vlan oui-table add 0060b9 Philips_and_NEC_AG_phone
voice vlan oui-table add 00d01e Pingtel_phone___________
voice vlan oui-table add 00e075 Polycom/Veritel_phone___
voice vlan oui-table add 00e0bb 3Com_phone______________
hostname xxx
ip ssh server
snmp-server location "xxx"
snmp-server contact "John Doe"
clock timezone CST 0 minutes 0
clock dhcp timezone
ip telnet server
interface vlan 1
ip address 192.168.1.2 255.255.255.0
no ip address dhcp
interface gigabitethernet1/1/1
switchport mode access
interface gigabitethernet1/1/2
switchport mode access
interface gigabitethernet1/1/3
switchport mode access
interface gigabitethernet1/1/4
switchport mode access
interface gigabitethernet1/1/5
switchport mode access
interface gigabitethernet1/1/6
switchport mode access
interface gigabitethernet1/1/7
switchport mode access
interface gigabitethernet1/1/8
switchport mode access
interface gigabitethernet1/1/9
switchport mode access
interface gigabitethernet1/1/10
switchport mode access
interface gigabitethernet1/1/11
switchport mode access
interface gigabitethernet1/1/12
switchport mode access
interface gigabitethernet1/1/13
switchport mode access
interface gigabitethernet1/1/14
switchport mode access
interface gigabitethernet1/1/15
switchport mode access
interface gigabitethernet1/1/16
switchport mode access
interface gigabitethernet1/1/17
switchport mode access
interface gigabitethernet1/1/18
switchport mode access
interface gigabitethernet1/1/19
switchport mode access
interface gigabitethernet1/1/20
switchport mode access
interface gigabitethernet1/1/21
switchport mode access
interface gigabitethernet1/1/22
switchport mode access
interface gigabitethernet1/1/23
switchport mode access
interface gigabitethernet1/1/24
switchport mode access
interface gigabitethernet1/1/25
switchport mode access
interface gigabitethernet1/1/26
switchport mode access
interface gigabitethernet1/1/27
switchport mode access
interface gigabitethernet1/1/28
switchport mode access
interface gigabitethernet1/1/29
switchport mode access
interface gigabitethernet1/1/30
switchport mode access
interface gigabitethernet1/1/31
switchport mode access
interface gigabitethernet1/1/32
switchport mode access
interface gigabitethernet1/1/33
switchport mode access
interface gigabitethernet1/1/34
switchport mode access
interface gigabitethernet1/1/35
switchport mode access
interface gigabitethernet1/1/36
switchport mode access
interface gigabitethernet1/1/37
switchport mode access
interface gigabitethernet1/1/38
switchport mode access
interface gigabitethernet1/1/39
switchport mode access
interface gigabitethernet1/1/40
switchport mode access
interface gigabitethernet1/1/41
switchport mode access
interface gigabitethernet1/1/42
switchport mode access
interface gigabitethernet1/1/43
switchport mode access
interface gigabitethernet1/1/44
switchport mode access
interface gigabitethernet1/1/45
switchport mode access
interface gigabitethernet1/1/46
switchport mode access
interface gigabitethernet1/1/47
switchport mode access
interface gigabitethernet1/1/48
switchport mode access
interface gigabitethernet1/1/51
switchport mode access
interface gigabitethernet1/1/52
switchport mode access
exit
macro auto disabled
ip default-gateway 192.168.1.1
encrypted
+++++++++++++++++++++++++++++++++++=
Cisco AIR-SAP2602I
! Last configuration change at 00:11:27 UTC Mon Mar 1 1993 by administrator
version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname XXX
logging rate-limit console 9
enable secret 5 $1$RVFD$DybWHlNypzf3XsnL6RGND/
no aaa new-model
no ip routing
ip domain name XXX
dot11 syslog
dot11 vlan-name Guest_VLAN vlan 200
dot11 vlan-name Internal_Users vlan 300
dot11 vlan-name default vlan 1
dot11 ssid Internal
   vlan 300
   authentication open
   authentication key-management wpa
   mbssid guest-mode
   wpa-psk ascii 7 05180704241A18471802161B05
dot11 ssid Guest
   vlan 200
   authentication open
   authentication key-management wpa
   guest-mode
   mbssid guest-mode
   infrastructure-ssid optional
   wpa-psk ascii 7 10652D4B5341151E09173E
crypto pki token default removal timeout 0
crypto pki trustpoint TP-self-signed-2946962253
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-2946962253
revocation-check none
rsakeypair TP-self-signed-2946962253
crypto pki certificate chain TP-self-signed-2946962253
certificate self-signed 01
3082022B 30820194 A0030201 02020101 300D0609 2A864886 F70D0101 05050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 32393436 39363232 3533301E 170D3933 30333031 30303431
34325A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D32 39343639
36323235 3330819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
81009438 47D6CAB8 36B9260D D5FEFA7A DFA7E065 E47ECCA2 346674C6 54D9C004
D6D62585 DE26A41E 447E8607 D0BD58C5 92899510 4EEBF95C 9352D082 1BB71EBF
72D56DDC 87D55A85 4A242578 6BBD31AD E48C8354 1C7331BD 5ED9F29D 5F8B868E
14DB0C08 3930D2D4 3266ED2D 9902DAA4 A348B722 82FCC132 6FC4BF22 DC7B9DBC
2F010203 010001A3 53305130 0F060355 1D130101 FF040530 030101FF 301F0603
551D2304 18301680 149FB8D9 F772C9DE 4BC86DD9 451902F3 4994F7D8 E0301D06
03551D0E 04160414 9FB8D9F7 72C9DE4B C86DD945 1902F349 94F7D8E0 300D0609
2A864886 F70D0101 05050003 81810054 FBCE018A CC09679F 8CB2D20A C773DE00
51AFA13A AB5105D5 BAAB6F2F B7CAF46A 2BFDCDDC F156593F 16C509EF 8C5215C1
7631DEFA 9E16633C 1E89CE65 C56591B2 5BE90BD0 1941F0EA 5478924C 4C0E229D
013743C3 2D4993E0 C44F9143 89A7A5D6 870E3A6C A772B8BB D032956F 1A5B894A
40EC55B9 8C5E3876 7E4B45FE 3DD00B
            quit
ip ssh version 1
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 1 mode ciphers aes-ccm
encryption vlan 100 mode ciphers aes-ccm
encryption vlan 200 mode ciphers aes-ccm
encryption vlan 300 mode ciphers aes-ccm
broadcast-key vlan 1 change 10000
broadcast-key vlan 100 change 10000
ssid Internal
ssid Guest
antenna gain 0
stbc
mbssid
station-role root
interface Dot11Radio0.200
encapsulation dot1Q 200 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio0.300
encapsulation dot1Q 300
no ip route-cache
bridge-group 255
bridge-group 255 subscriber-loop-control
bridge-group 255 spanning-disabled
bridge-group 255 block-unknown-source
no bridge-group 255 source-learning
no bridge-group 255 unicast-flooding
interface Dot11Radio1
no ip address
no ip route-cache
encryption vlan 1 mode ciphers aes-ccm
encryption vlan 300 mode ciphers aes-ccm
encryption vlan 200 mode ciphers aes-ccm
broadcast-key vlan 1 change 10000
antenna gain 0
dfs band 3 block
channel dfs
station-role root
interface Dot11Radio1.1
encapsulation dot1Q 1
no ip route-cache
interface Dot11Radio1.200
encapsulation dot1Q 200 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio1.300
encapsulation dot1Q 300
no ip route-cache
bridge-group 255
bridge-group 255 subscriber-loop-control
bridge-group 255 spanning-disabled
bridge-group 255 block-unknown-source
no bridge-group 255 source-learning
no bridge-group 255 unicast-flooding
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
no keepalive
hold-queue 160 in
interface GigabitEthernet0.1
encapsulation dot1Q 1
no ip route-cache
interface GigabitEthernet0.200
encapsulation dot1Q 200 native
no ip route-cache
bridge-group 1
bridge-group 1 spanning-disabled
no bridge-group 1 source-learning
interface GigabitEthernet0.300
encapsulation dot1Q 300
no ip route-cache
bridge-group 255
bridge-group 255 spanning-disabled
no bridge-group 255 source-learning
interface BVI1
ip address 192.168.1.10 255.255.255.0
no ip route-cache
ip default-gateway 192.168.1.1
no ip http server
ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
line con 0
line vty 0 4
login local
transport input all
end
+++++++++++++++++++++++++++++++++++++++++
I was able to get dhcp from the Sonicwall with 192.168.1.0/24, but not from the SG500. I created a scope(192.168.2.0/24 for guest; 192.168.3.0/24 for internal users) I even created DHCP scope on the AP, but cannot get an IP from that either. I creatd an ACL to allow the 192.168.3.0/24 access elewhere, and denied 192.168.2.0 access to other but internet.
If I disabled all scopes on the Sonicwall, I get an APIPA from both AP/SG500. Any thoughts?

What is your default VLAN?
On the AP, you configured VLAN 200 to be the native. is that the same with your othe devices?
"encapsulation dot1Q 200 native"
Regards,
Amjad
Rating useful replies is more useful than saying "Thank you"

Upgrade of 4402 Controller to 7.0.98.0 or 7.0.22.0 breaks WLC ability to display 1130 series APs

Almost a year ago we upgraded our 4402 Controller to 7.0.98.0 to support our 1262 APs. This allowed them to be in our network. We recently realized that we are unable to access the 1130 APs directly from the WLC. We can still access them from the controller GUI, but not the WLC gui. If we downgrade to the 6.0.202.0, it fixes the issue with the 1130's, but we can longer have the 1262's on our network. The error we get when we try to connect to 1130's while on 7.0.98.0 or 7.0.220.0 is as follows:
7.0.98.0 error
Error: Object "LradMeshNode" does not exist
7.0.220.0 error
Error: Object "Child of Lrad#302675 (Lrad00:15:c7:2a:20:c0) class LradMeshNode" does not exist.
Any suggestions?
thanks,
Steve

do you mean you can't see the 1131 on wcs ?
If so, is your wcs on the same code rev as your wlc or a head ? Wcs should always be at or a head in code than your wlc ..
Sent from Cisco Technical Support iPhone App

Flex Based AIR application & remote HTML

The question is ....from a flex based AIR application do you
always have full access to all of the HTML content loaded from a
remote site via the DOM (htmlLoader.window.document), or is the
'context' of what you can see limited to what the initial url
requested can see - i.e. the context is as if it were javascript
running in the page corresponding to the initial URL.
As far as i can see if i request say the page
http://www.abc.com/page1.htm
and it has content along the lines of
<IFRAME src="
http://www.xyz.com/page3.htm"
id="remoteframe" />
<IFRAME src="
http://www.abs.com/page2.htm"
id="localframe" /?
then using the htmlControl.htmlLoader.window.document i can
successfully navigate the DOM for the initial page loaded and
localframe, but
not remoteframe.
I've seen various comments about sandboxes, bridges and
applicationdomains in the documentation but i don't see how this
can help me.
Can someone please shed some light on this? Can i from the
AIR application access all of the DOM, or am i restricted to the
initially loaded page and pages referenced from the same domain in
the page?
Thanks
Jamie

Hi,
From your AIR application, you can only access "exposed
properties" in remoteframe.
You expose a property by using the sandbox bridge mechanism:
http://livedocs.adobe.com/air/1/devappshtml/help.html?content=security_5.html#1092959

Upgrading Autonomous to controller-based (AIR-SAP2602I)

Similar Messages

Maybe you are looking for