Upgrading to ISE 1.3 error ISE Global data upgrade failed!

HI,
Has anyone come across this issue? when upgrading, it seems to start all well but then this happens:
- Data upgrade step 40/67, CertMgmtUpgradeService(1.3.0.616)... % Error: ISE Global data upgrade failed!
Rolling back the configuration database...
Starting application after rollback...
% Error: The node has been reverted back to its pre-upgrade state.
% Application install or upgrade cancelled.
I've also upgraded it to the latest patch and tried again but to no avail. This is an appliance (3415) that came shipped with 1.2. It's not been configured other than the initial cli wizard. I've upgraded a fair few appliances but I haven't seen this issue come up before. Any thoughts?
Thanks in advance for any info...

If this is a test setup then you can do fresh ISE install.back up existing config and restore it to 1.3. If its production then contact TAC

Similar Messages

Excel 2007 = Refresh All = Error Message "Initialization Data Source Failed"

Excel 2007 => Data Tab - Refresh All => Error Message "Initialization Data Source Failed
2nd Error message:
The following data ranged failed to refresh: ExternalData1 - Continue to refresh all
How do I resolve this? Trying to connect to Oracle DB environment 12C

What will happen if you rebuild the PivotTable/Table ?
Make sure the external database is available and the Oracle Provider for OLE DB is installed correctly.
Wind Zhang
TechNet Community Support

ERROR: validate with data file failed

Hi,
We are using SAP BPC 7.5 NW SP08(Admin & client). We are trying to load transaction data from BW actual cube to BPC application for which we have written the following transformation file.
*MAPPING
CATEGORY=*NEWCOL(ACTUAL)
P_ACCT2=MVAL(0RECTOTSTCK|NEWCOL(PRODQU))
P_DATASRC=*NEWCOL(INPUT)
MATERIALBW=0MATERIAL
RPTCURRENCY=0LOC_CURRY
TIME=0CALMONTH
SIGNEDDATA=0RECTOTSTCK
*CONVERSION
TIME=Conversion for IM Actuals.XLS!CONVERSION
We want to map BW keyfigure 0RECTOTSTK (production quantity) to PRODQU - a member of the dimension P_ACCT2. And also we want to load the data from that key figure into our SIGNEDDATA field in BPC.
We have validated and processed the conversion file without error, but getting the following error while validating definition of the transformation file:
"ERROR: validate with data file failed"
Can you please help on this.
Thanks in advance.
Appu

Issue was resolved.We were trying to load data from the cube 0IC_C03.However, that cube had some non-cumulative key figures. BPC 7.5 SP08 does not allow data to be loaded from BW cubes having non-cumulative key-figures to BPC Cubes.This is a bug which will be rectified in SP11 according to SAP.
Since we needed only 0RECTOTSTCK which is a cumulative key figure we created a separate BW cube and loaded it from 0IC_C03 using only the necessary cumulative key figures and other dimensions.We then used the new cube to load data into BPC cube and it worked.

Invalid data status error during the data extraction

Hi,
while extracting capacity data from the SNP Capacity view to BW. i get the "invalid data status error" and the data extraction fails.
when debugged the bad requests of the ODS object, i found that for a certain product(which has both positive and negative input and out qtys) co-product manufacturing orders were created. but this product was not marked as the co-product and functionally its fine.
how can i rectify the data extraction problem..can you advice.
Thanks,
Dhanush

Sir,
In my company for some production order status some are having "errors in cost calculation" ie "cser" .how to deal these kind of errors.

Help with cisco ISE 1.1.2.145 patch-3 to ISE 1.2.0.899-2-85601 upgrade procedure

Need help from ISE experts/gurus in this forum.
Due to a nasty bug in Cisco ISE (bug ID CSCue38827 ISE Adclient daemon not initializing on leave/join), this bug will make the ISE stopping working completely and a reboot is required (very nice bug from cisco) . This leaves me no choice but to upgrade to version 1.2.0.899-2-85601.
Scenario:
- 4 nodes in the environment running ISE version 1.1.2.145 patch 3
- node 1 is Primary Admin and Secondary Monitoring - hostname is node1
- node 2 is Secondary Admin and Primary Monitoring - hostname is node2
- node 3 is Policy service node - hostname is node3
- node 4 is Policy service node - hostname is node4
Objective: Upgrade the ISE environment to ISE version 1.2 with patch version 1.2.0.899-2-85601.
My understand is that I have to upgrade the existing environment from ISE version 1.1.2.145 patch 3
to ISE version 1.1.2.145 patch 10 (patch 10 was released on 10/04/2013) before I can proceed with
upgrading to ISE version 1.2 and patch it with 1.2.0.899-2-85601.
Can I patch my exsiting environment from 1.1.2 patch 3 to patch 10 prior to upgrading to version 1.2.0.899-2-85601?
I look at Cisco website and patch 10 was released on 10/04/2013 while version 1.2 was released back in 07/05/2013.
I am trying to get a definite answer from Cisco TAC but it seems like they don't know either.
Question #1: How do I proceed with upgrading the current ISE environment from 1.1.2.145 patch 3 to 1.1.2.145 patch 10?
Propose solution:
step #1: make ISE node1 to be both Primary Admin and Primary monitoring. ISE node2 is now Secondary Admin and Secondary Monitoring.
         Then go ahead and apply ISE version 1.1.2.145 patch 10 to ISE node2 via the GUI,
step #2: Once ISE node2 patch 10 is completed, make node2 Primary Admin and Primary Monitoring. At this point, apply ISE 1.1.2.145 patch 10
         to ISE node1 via the GUI,
step #3: Once ISE node1 patch 10 is completed, make node1 Primary Admin and Secondary Monitoring and node2 Secondary Admin and Primary Monitoring,
step #4: apply ISE 1.1.2.145 patch 10 to ISE Policy Service node3. Once that is completed, verify that node2 is working and accepting traffics,
step #5: apply ISE 1.1.2.145 patch 10 to ISE Policy Service node4. Once that is completed, verify that node2 is working and accepting traffics,
Question #2: How do I proceed with upgrading the current ISE environment from 1.1.2.145 patch 10 to ISE version 1.2 with patch version 1.2.0.899-2-85601?
Propose solution:
step #1: Make ISE node1 the Primary Admin and Primary monitoring. At this point ISE node2 will become Secondary Admin and Secondary Monitoring
step #2: Perform upgrade on the ISE node2 via the command line "application upgrade <app-bundle> <repository>". Once ISE node2 upgrade is completed, it will
          form a new ISE 1.2 cluster independent of the old cluster,
step #3: Perform upgrade on the ISE Policy Service node3 via the command line "application upgrade <app-bundle> <repository>". After the upgrade the ISE
          Policy Service Node3 will automatically joins the ISE node2 which is already in version 1.2
step #4: Perform upgrade on the ISE Policy Service node4 via the command line "application upgrade <app-bundle> <repository>". After the upgrade the ISE
          Policy Service Node4 will automatically joins the ISE node2 which is already in version 1.2
step #5: At this point the only node remaining in the 1.1.2.145 patch 10 is the ISE node1 Primary Admin and Primary Monitoring
step #6: Check and see if there are any more PSN's registered in ISE node1 (there should not be any)
step #7: Perform the upgrade on the ISE node1 from command line "application upgrade <app-bundle> <repository>"
step #8: Once upgrade on ISE node1 is complete, ISE node1 will automatically join the new ISE 1.2 cluster,
step #9: Make ISE node1 Primary Admin and Secondary and ISE node2 Secondary Admin and Primary Monitoring,
Question #3: How do I proceed with upgrading the current ISE environment from 1.2 patch0 to 1.2.0.899-2-85601?
Propose solution:
step #1: make ISE node1 to be both Primary Admin and Primary monitoring. ISE node2 is now Secondary Admin and Secondary Monitoring.
         Then go ahead and apply ISE 1.2.0.899-2-85601 to ISE node2 via the GUI,
step #2: Once ISE node2 1.2.0.899-2-85601 is completed, make node2 Primary Admin and Primary Monitoring. At this point, apply 1.2.0.899-2-85601
         to ISE node1 via the GUI,
step #3: Once ISE node1 patch 10 is completed, make node1 Primary Admin and Secondary Monitoring and node2 Secondary Admin and Primary Monitoring,
step #4: apply ISE 1.2.0.899-2-85601 to ISE Policy Service node3. Once that is completed, verify that node2 is working and accepting traffics,
step #5: apply ISE 1.2.0.899-2-85601 to ISE Policy Service node4. Once that is completed, verify that node2 is working and accepting traffics,
does these steps make sense to you?
Thanks in advance.

David,
A few answers to your questions -
Question 1: My recommendation is to follow vivek's blog since most fixes and upgrade steps are provided there - I would recommend installing the patch that was release prior to the 1.2 release date since the directions to "install the latest patch" would put you at the version of when the ISE 1.2 was released
https://supportforums.cisco.com/community/netpro/security/aaa/blog/2013/07/19/upgrading-to-identity-services-engine-ise-12
You do not have the ability to install ISE patch through the GUI on any of the "non-primary" nodes (you can use the cli commmand to achieve this), the current patching process was designed so you can install the patch on the primary admin node and it will then roll the patches out to the entire deployment (one node at at time). I painfully verified this by watching the services on each node and when a node was up and operational the next node would start the patching process. First the admin nodes then the PSNs.
Every ISE upgrade that I have attempted as not been flawless and I can assure you that I have done an upgrade on 1.1.2 patch 3 and this worked fine, however I used the following process. You will need the service account information that is used to join your ISE to AD.
I picked the secondary admin/monitoring node and made it a standalone node by deregistering (much like the old procedure) in your case this will be node2.
I backed up the certificates from the UI and the database from the CLI (pick the local disk or ftp-your choice).
I reset the database and ran the upgrade script (since I did not have access to the vsphere console or at the location of the non UCS hardware [for a 1.1.4 upgrade]).
Once the upgrade was completed I then restored the 1.1.x database, ISE 1.2 now has the ability to detect the version of the database that is restored and will perform the migration for you.
Once the restore finished, I then restored the certificate and picked one of the PSNs
backup the cert,
Had the AD join user account handy
reset-db,
and run the upgrade script.
Once that is done I then restore the cert
Join the PSN to the new deployment
Join both nodes to AD through primary admin node
Monitor for a few days (seperate consoles to make sure everything runs smooth)
If anything doesnt look or feel right, you can shut down the 1.2 PSN and force everything through the existing 1.1.2 setup and perform some investigation, if it all goes smooth you can then follow the above step for the other two nodes, starting with the last PSN and the the last admin node.
Thanks and I hope that helps,
Tarik Admani
*Please rate helpful posts*

Meaning of this error (ISE 1.2 on SNS-3415): HARDWARE RNG INTEGRITY CHECK HAS FAILED!

Hi. We recently purchased an ISE 1.2 appliance (SNS-3415 hardware). It installed fine, but I am unable to access the GUI. When I login to the box and run the following command on the CLI
ISE-12-NS-SD-2/admin# show application status ise
I see the following output:
ISE Database listener is running, PID: 7737
ISE Database is running, number of processes: 38
ISE Application Server process is not running.
ISE Profiler DB is running, PID: 9090
ISE M&T Session Database is running, PID: 8959
ISE M&T Log Collector is running, PID: 9294
ISE M&T Log Processor is running, PID: 9376
% ERROR: ISE SERVICES HAVE BEEN DISABLED BECAUSE
% HARDWARE RNG INTEGRITY CHECK HAS FAILED!
Can anyone help me? What can I do to ensure that the hardware RNG integrity check succeeds. Is it a license issue? Is it faulty hardware? Please advise. I would be very greatful.
Thanks in advance.

I worked with a TAC engineer on this and he said one other customer had this issue and the only recourse was reimaging the appliance with the ISE 1.2 ISO image.
I did reboot, restarted services, reset to factory default and none of that worked. It is possible that the issue happened because during setup of the appliance I didn't have network connectivity and went ahead with the setup and configuration of the ISE application anyway. I later had network connectivity but by that time ISE manifested this fault.
Reimaging and ensuring network connectivity during setup the next time around fixed the problem.

I dont have any Add-ons with my FireFox. After upgrade to the latest version 26.0 I'm keep getting Script error "chrome://global/content/binding/popup.xml:580"

Quite frequently I'm keep getting the error like "Script is not responding....I dont have any Add-ons with my FireFox. After upgrade to the latest version 26.0 I'm keep getting Script error "chrome://global/content/binding/popup.xml:580" Stop or Continue Script.
Currently I don't have any Add-Ons installed in my FireFox, so I can suspect any Add-ons.
I'm facing this issue only after the upgrade to 26.0 recently.

Ifound this article:
https://support.mozilla.org/pt-BR/questions/746499
in this article the problem is similar not the same, but sdmitch16 had a intersting idea disable the chrome options
and i search more in the internet i also found this:
https://support.mozilla.org/pt-BR/questions/760704

Do I need Cisco ISE VM Part # L-ISE-VM-K9= for ESXi installation

Hi there,
Do I need the L-ISE-VM-K9 license to install Cisco ISE on an ESXi ?
Actually, Cisco ISE can be downloaded with an Eval License for 90 days.
I know, ISE license (e.g. Base License) is needed.
Thanks a lot.
Greetings,
Norbert

Just in case you you would like to see the specification of each licence.
License Type
Features Supported
Deployment Type Supported
License Prerequisite
License Term(s)
Base License
AAA
Guest Provisioning
Link Encryption Policies
Wired
Wireless
VPN
Perpetual
Advanced License
Device Onboarding/Provisioning
Device Profiling and Feed Service*
Host Posture
Security Group Access
Integrated Vendor MDM Support*
Wired
Wireless
VPN
Base License
3- and 5-Year Terms
Wireless License
Device Onboarding/Provisioning
AAA
Guest Provisioning
Link Encryption Policies
Device Profiling and Feed Service*
Host Posture
Security Group Access
Integrated Vendor MDM Support*
Wireless
3- and 5-Year Terms
Wireless Upgrade License
Device Onboarding/Provisioning
Authentication/Authorization
Guest Provisioning
Link Encryption Policies
Device Profiling
Host Posture
Security Group Access
Wired
Wireless
VPN
Wireless License
3- and 5-Year Terms
Cisco ISE Functionality-Based License Options
License Tiers (T)
Number of Endpoints Supported
Base License
Advanced 3-Year License
Advanced 5-Year License
Wireless 3-Year License
Wireless 5-Year License
Wireless Upgrade 3-Year License
Wireless Upgrade 5-Year License
100
100 Endpoints
L-ISE-BSE-100=
L-ISE-ADV3Y-100=
L-ISE-ADV5Y-100=
L-ISE-AD3Y-W-100=
L-ISE-AD5Y-W-100=
L-ISE-W-3UPG-100=
L-ISE-W-UPG-100=
250
250 Endpoints
L-ISE-BSE-250-
L-ISE-ADV3Y-250=
L-ISE-ADV5Y-250=
L-ISE-AD3Y-W-250=
L-ISE-AD5Y-W-250=
L-ISE-W-3UPG-250=
L-ISE-W-UPG-250=
500
500 Endpoints
L-ISE-BSE-500=
L-ISE-ADV3Y-500=
L-ISE-ADV5Y-500=
L-ISE-AD3Y-W-500=
L-ISE-AD5Y-W-500=
L-ISE-W-3UPG-500=
L-ISE-W-UPG-500=
1000
1000 Endpoints
L-ISE-BSE-1K=
L-ISE-ADV3Y-1K=
L-ISE-ADV5Y-1K=
L-ISE-AD3Y-W-1K=
L-ISE-AD5Y-W-1K=
L-ISE-W-3UPG-1K=
L-ISE-W-UPG-1K=
1500
1500 Endpoints
L-ISE-BSE-1500=
L-ISE-ADV3Y-1500=
L-ISE-ADV5Y-1500=
L-ISE-AD3Y-W-1500=
L-ISE-AD5Y-W-1500=
L-ISE-W-3UPG-1500=
L-ISE-W-UPG-1500=
2500
2500 Endpoints
L-ISE-BSE-2500=
L-ISE-ADV3Y-2500=
L-ISE-ADV5Y-2500=
L-ISE-AD3Y-W-2500=
L-ISE-AD5Y-W-2500=
L-ISE-W-3UPG-2500=
L-ISE-W-UPG-2500=
3500
3500 Endpoints
L-ISE-BSE-3500=
L-ISE-ADV3Y-3500=
L-ISE-ADV5Y-3500=
L-ISE-AD3Y-W-3500=
L-ISE-AD5Y-W-3500=
L-ISE-W-3UPG-3500=
L-ISE-W-UPG-3500=
5000
5000 Endpoints
L-ISE-BSE-5K=
L-ISE-ADV3Y-5K=
L-ISE-ADV5Y-5K=
L-ISE-AD3Y-W-5K=
L-ISE-AD5Y-W-5K=
L-ISE-W-3UPG-5K=
L-ISE-W-UPG-5K=
10,000
10K Endpoints
L-ISE-BSE-10K=
L-ISE-ADV3Y-10K=
L-ISE-ADV5Y-10K=
L-ISE-AD3Y-W-10K=
L-ISE-AD5Y-W-10K=
L-ISE-W-3UPG-10K=
L-ISE-W-UPG-10K=
25,000
25K Endpoints
L-ISE-BSE-25K=
L-ISE-ADV3Y-25K=
L-ISE-ADV5Y-25K=
L-ISE-AD3Y-W-25K=
L-ISE-AD5Y-W-25K=
L-ISE-W-3UPG-25K=
L-ISE-W-UPG-25K=
50,000
50K Endpoints
L-ISE-BSE-50K=
L-ISE-ADV3Y-50K=
L-ISE-ADV5Y-50K=
L-ISE-AD3Y-W-50K=
L-ISE-AD5Y-W-50K=
L-ISE-W-3UPG-50K=
L-ISE-W-UPG-50K=
100,000
100K Endpoints
L-ISE-BSE-100K=
L-ISE-ADV3Y-100K=
L-ISE-ADV5Y-100K=
L-ISE-AD3Y-W-100K=
L-ISE-AD5Y-W-100K=
L-ISE-W-3UPG-100K=
L-ISE-W-UPG-100K=
Cisco ISE Functionality-Based License Options
License Type
License SKU
Base License
L-ISE-BSE-[T]=
Advanced 3-Year License
L-ISE-ADV3Y-[T]=
Advanced 5-Year License
L-ISE-ADV5Y-[T]=
3-Year Wireless License
L-ISE-AD3Y-W-[T]=
5-Year Wireless License
L-ISE-AD5Y-W-[T]=
3-Year Wireless Upgrade License
L-ISE-W-3UPG-[T]=
5-Year Wireless Upgrade License
L-ISE-W-UPG-[T]=
Replace [T] with the appropriate license tier from Table 5 and 6.
Jatin Katyal
- Do rate helpful posts -

ISE default settings for "ISE - Process Status"

Please put default settings for alerts "ISE - Process Status" for CiscoISE (PAN / Operations / Alarms / Rules / Criteria / Monitor Processes).
For example, for version 1.1.4.218 for virtual machines.
Thanks in advance!

Hi
You can view process status for the network from the Cisco ISE dashboard using the System Summary dashlet. For example, when processes like the application server or database fail, an alarm is generated and you can view the results using the System Summary dashlet.
One of the requirements for creating an alarm rule is that you assign it to a schedule. The following task shows you how to create an alarm rule, and then assign it to a schedule.
The following default alarm rules are shown in the user interface:
• ISE - AAA Health
• ISE - Process Status
• ISE - System Errors
• ISE - System Health
You can create these alarm rules using the following procedure:
• Passed Authentication
• Failed Authentication
• Authentication Inactivity
• Authenticated But No Accounting Start
• Unknown NAD
• External DB Unavailable
• RBACL Drops
For more information about configuration etc please go through this link:
http://www.cisco.com/en/US/docs/security/ise/1.1.1/user_guide/ise_ug.pdf
at page no.928

IPod touch is not recognized by Windows (with a connect to iTune screen) after OS 5.1.1 upgrade and received an 1602 error

My iPod touch is not recognized by Windows 7 and will not appear on My Computer as a storage device after OS 5.1.1 upgrade and received an 1602 error. My iPod is now having a connect to iTune screen.

Error 1600, 1601, 1602: Try the following steps to resolve this error:
Ensure proper USB isolation troubleshooting has been performed, and test with a known-good cable.
Follow the steps listed for Error 1604.
This error may be resolved by disabling, deactivating, or uninstalling third-party security, antivirus, and firewall software. See steps in this article for details on troubleshooting security software.
http://support.apple.com/kb/TS3694#error1602

Error while doing EHP4 upgrade in downtime phase

HI .
Iam facing the below error while doing the EHP4 upgrade , in downtime phase.
Checks after phase MAIN_SWITCH/STARTSAP_TRANS were negative!
Last error code set: RFC call to subst_get_uvers failed with key RFC_ERROR_COMMUNICATION (open): SAP_CMINIT3 : rc=20 >
Connect to SAP gateway failed Connect_PM GWHOST=Hydhtc4526D, GWSERV=sapgw04, SYSNR=04 LOCATION CPIC (TCP/IP) on local host with Unicode ERROR partner '10.136.162.30:3304' not reached TIME Mon Jun 06 18:17:46 2011 RELEASE 720 COMPONENT NI (network interface) VERSION 40 RC -10 MODULE nixxi.cpp LINE 3286 DETAIL NiPConnect2: 10.136.162.30:3304 SYSTEM CALL connect ERRNO 10061 ERRNO TEXT WSAECONNREFUSED: Connection refused COUNTER System start failed
Please help me in resolving this error.
Sanketh.

Hi,
Upgrade tool is trying to start the system but system is not coming up. Try to start system manually and see if system comes up or not. If not then check logs in work directory for why system is not coming up.
Thanks
Sunny

After upgrading to 27, firefox will not start. Saw an error message during the upgrade process.

After upgrading to 27, firefox will not start. Saw an error message during the upgrade process but cannot remember.
Tried to run firefox.exe -P but receive error message:
XML Parsing error: undefined entity
Location: chrome://mozapps/content/profile/profileSelection.xul
Line number 18, Column 1:
<dialog
^
Running on Windows XP SP3. No problem whatsoever before upgrading to 27. Sending this from Chrome as I cannot open Firefox at all.

Thanks jschaer2000: after starting it once in safe mode, I closed Mozilla and tried several restarts in normal mode. So far, all worked:-)
Thank you very much again.
Still the automatic update process bothers me: it took me several days to discover the reason to the malfunction, since when I removed the problematic version from Add and Remove Programs, I didn't pay attention at first that it was another version, not v26 which I installed from my folder.
In addition, I like to save the installation files before I run new programs and if I didn't have v26 exe file, I couldn't have operated Mozilla at all. Not that it was fun to remove and install again each time v27 didn't react, but it was better than nothing, I still prefer Mozilla over its competition.

Error in PHASE ACT_UPG: Upgrade SAP R/3 4.7 to SAP ECC 6.0 EHP

Hello,
I'm facing an error in phase MAIN_SHDRUN/ACT_UPG (see errors below).
After searching for the errors I found postings with advice to change R3trans and tp to the newest version. Strangely system did not take the newest kernelpatch I stored in upgrade folder. So I changed the files in the /usr/sap/SID/abap/exe folder and repeated the phase.
But the error is still there.
A solution was to reset the queue, but this is only possible with help by sap.
Error in phase: DDIC_ACTIVATION
So I'm waiting for their reaction since two days, but nothing happens.
My questions are now:
what happens if I use the option "initialize phase ACT_UPG to restart it from beginning"? Will the new R3trans be used? Have we got to to the SPDD again?
What happens if I use the option "accept non severe errors and repeat phase ACT_UPG? Are these language errors "non-severe"?
Errors:
In error log ACTUPG.ELG I find logs like:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
DDIC ACTIVATION ERRORS and RETURN CODE in SAPA-60016INERECRUIT.REX
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
1 ETP111 exit code : "8"
In error log SAPup.ECO I find:
EXECUTING /usr/sap/REX/upg/abap/exe/tp (/usr/sap/REX/upg/abap/exe/tp) pf=/usr/sap/REX/upg/abap/bin/ACTUPG.TPP put REX
This is /usr/sap/REX/upg/abap/exe/tp version 376.01.14 (release 701)
Warning: Parameter INTERRUPT is no longer used.
Warning: Parameter DAYLIGHT_SHUTDOWN is no longer used.
Warning: Parameter WITH_TACOB is no longer used.
Warning: Parameter IMPDP_BY_EVENT is no longer used.
Warning: Parameter INTERRUPT is no longer used.
Warning: Parameter DAYLIGHT_SHUTDOWN is no longer used.
Warning: Parameter WITH_TACOB is no longer used.
Warning: Parameter IMPDP_BY_EVENT is no longer used.
Looking for effective putsteps ... ... ready (looking for putsteps)
tp finished with return code: 8
meaning:
A tool used by tp produced errors
Process with ID 13163 terminated with status 8
In the last touched SP-File SAPAAAA701.SID I can find errors like:
"1EEDO545 "LANG" "DTEL" "*": Object information could not be imported"
Regards,
Julia

After pushing the message at SAP I got the following answer:
It is the problem from note 1417505. There is no guarantee that all objects where imported with the used R3trans. A rerun of phase will be unsuccessfully because error came up in DDIC_IMPORT.
A reset of the queue is only possible if SPAM/SAINT is used for importing support packages. In case of upgrade, like here, the upgrade has got to be resetted as described in upgrade guide.
After start between phase extraction and configuration the newest R3trans has got to be copied manually in /abap/exe folder.
Regards,
Julia

Error message while while upgrading FIM RTM to FIM Service pack 1

Hi All,
I am getting the below error message while while upgrading FIM RTM to FIM Service pack 1, I had followed the same procedure in one of my test lab and it upgraded successfully. Kindly advice.
Regards,
Anirban Singha

HI Dominik,
Thanks for reply,
Event Error,
Product: Forefront Identity Manager Synchronization Service - Update 'FIM Synchronization Service Hotfix KB 2814853' could not be installed. Error code 1603. Additional information is available in the log file E:\FIMR2-SP1\logfile.txt.
MSI Logs:
CustomAction DetectServiceAccount returned actual error code 1603 (note this may not be 100% accurate if translation happened inside sandbox)
Action ended 15:06:14: DetectServiceAccount. Return value 3.
MSI (c) (C4:10) [15:06:14:359]: Doing action: SetupCompleteError
Action 15:06:14: SetupCompleteError.
Action start 15:06:14: SetupCompleteError.
MSI (c) (C4:20) [15:06:14:365]: Transforming table Binary.
MSI (c) (C4:20) [15:06:14:365]: Transforming table Binary.
MSI (c) (C4:20) [15:06:14:365]: Note: 1: 2262 2: Binary 3: -2147287038
Action 15:06:14: SetupCompleteError. Dialog created
MSI (c) (C4:A0) [15:06:14:376]: Note: 1: 2731 2: 0
Action ended 15:06:19: SetupCompleteError. Return value 2.
Action ended 15:06:19: INSTALL. Return value 3.
MSI (c) (C4:10) [15:06:19:627]: Destroying RemoteAPI object.
MSI (c) (C4:E0) [15:06:19:628]: Custom Action Manager thread ending.
Property(C): DiskPrompt = [1]
Property(C): UpgradeCode = {545334D7-13CD-4BAB-8DA1-2775FA8CF7C2}
Property(C): PID = 04783-270-0001260-04309
Property(C): MIIS_PATH = C:\Program Files\Microsoft Forefront Identity Manager\2010\Synchronization Service\
Property(C): INSTALLDIR = C:\Program Files\Microsoft Forefront Identity Manager\2010\
Property(C): WWF35 = 3.5.30729.5420
Property(C): DOTNETINSTALLROOT = C:\Windows\Microsoft.NET\Framework64\
Property(C): SQLDB = FIMSynchronizationService
Property(C): EVENTSOURCE = FIMSynchronizationService
Property(C): EVENTPRODUCTNAME = FIM Synchronization Service
Property(C): SYNCINSTALLPATH = C:\Program Files\Microsoft Forefront Identity Manager\2010\Synchronization Service\
Property(C): GROUPADMINS = MPHASIS\FIMSyncAdmins
Property(C): GROUPOPERATORS = MPHASIS\FIMSyncOperators
Property(C): GROUPACCOUNTJOINERS = MPHASIS\FIMSyncJoiners
Property(C): GROUPBROWSE = MPHASIS\FIMSyncBrowse
Property(C): GROUPPASSWORDSET = MPHASIS\FIMSyncPasswordSet
Property(C): SQLServerStore = LocalMachine

ECC 6 SR3 upgrade I am getting following error at RSVBCHCK

2EETQ241 Errors found in logfiles - accumulated in file "PSVBCHCK.ELG"
1EETQ203 Upgrade phase "JOB_RSVBCHCK_D" aborted with errors
1 ETH010XRSVBCHCK: Check of open update requests
2EETG050 Update records still exist - Please process.
There is no SM13 nor SMQ1 entries in the system, also reorganiezed update records, also checked following.
SQL> select * from sapr3.VBERROR;
no rows selected
SQL> select * from SAPR3.VBERROR;
no rows selected
SQL> select * from SAPR3.VBMOD;
no rows selected
SQL> select * from SAPR3.VBHDR;
no rows selected
SQL>
Incase anyone had faced similar issues, and found a workarond please let me know
thanks.

Hi Mathew,
Please check if your system has the ABAP program "RMCEXCHK" as per OSS Note no. 1083709.
Once you run this program, it exactly would let you know what are the areas which are causing the issues. Based on that you can empty out the LIS Set up tables.
Also, can you please check the update program for LIS has emptied out the entries in SMQ1.
Regards,
Anil

Upgrading to ISE 1.3 error ISE Global data upgrade failed!

Similar Messages

Maybe you are looking for