Upgrading to Patch Level 47

Hi Experts,
We are upgrading to Patch 47 from PL 30. When I try and login to one of our databases, I get the error messages
1. This entry already exists in the following table - Company Info (CINF)
2. Then I get another message stating - The company DB is not consistent see log files.
Please can anyone assist? What can cause these errors?

Hi,
Have you checked these threads?
The company DB is not consistent
Company DB is not consistent
Thanks,
Gordon

Similar Messages

PI 7.1 upgrade - PI_BASIS patch level in ECC

Hello
We are looking at upgrading our XI 7.0 SP12 to PI 7.1. Our backend ECC system is at PI_BASIS SP11. Most of our interfaces with the backend are through ABAP proxies.
Will an upgrade to PI 7.1 demand an upgrade to PI_BASIS in the backend ECC system as well?
If not, what is the minimum SP level the PI_BASIS component in the backend ECC system should be at?
I don't find this information in upgrade guide; where will this information be normally available?
Thanks
KK

You can use PI 7.1 with any SAP system.
However, if you want to use Abap proxies based on message interfaces of type "stateless" with WS-RM protocol, the ECC requires SP 14.
The Abap proxies based on XI 3.0 protocol do not require any special patch level.
Regards
Stefan
Edited by: Stefan Grube on Aug 28, 2008 4:34 PM

Problem after upgrade from patch level 36 to 43

Hi,
Recently our system is upgraded from 36 to 43 patch level. After this there are problem in doing hiring action, IT0000 is saving but the next infotype IT0001 does not gets saved and also no error message. So, really not able to figure out what could be the problem.
I was debugging the standard code i.e once the 'save' button is clicked in IT0001 in PA40, but in vain. I am not able to find out where or in which program/include the data gets saved in PA0001. If any one aware of this please let me know.
Since IT0001 is not getting saved, there are probs with IT0007 and IT0008.
Please let me know your views.
Thanks,
Arunsri

Hi Raju,
Thanks for the reply. Ya, the problem was not due to upgrade,but some other issue. Not able to find till now. I checked IGMOD features and it is in 'Active' mode only. No luck.
Edited by: Arunsri on Jan 27, 2012 4:18 PM

Kernel upgrade to patch level 196, ECC 5.0, MSCS resource issue.

Hi,
We have 3 system landscape DEV, QAS & PRD on win 2003, oracle 10G, ECC 5.0.
Our PRD system is on MSCS with CI on node A and DB on node B.
Recently I successfully upgrade kernel off DEV & QAS system to patch level 196 of stack 18.
When I tried to upgrade the kernel of PRD system one of the cluster resource drive (The drive contains the usr folder) is automatically moving from Node A to Node B and I got the error u201Capplication server shut downu201D. We donu2019t have additional application server in the landscape.
Please suggest the solution.
Regards,
Rajesh

Hi Juan,
How are you? Thanks for your reply.
We are using ECC 5.0. I have found more errors in dev_w0 as follows,
ERROR => ShmCreate( ATTACH 62, 85588600) failed 1 [mpixx.c      843]
ERROR => DpInitMpi: MpiInit failed (1) [dpxxtool2.c 3556]
in_ThErrHandle: 1
ERROR => tskh_init: DpInitMpi (step 1, th_errno 17, action 3, level 1) [thxxhead.c   9621]
Info for wp 0
stat = 4
reqtype = 1
act_reqtype = -1
rq_info = 0
tid = -1
mode = 255
len = -1
rq_id = 65535
rq_source = 255
last_tid = 0
last_mode = 0
int_checked_resource(RFC) = 0
ext_checked_resource(RFC) = 0
int_checked_resource(HTTP) = 0
ext_checked_resource(HTTP) = 0
report = >                                        <
action = 0
tab_name = >                              <
LOCATION    SAP-Server sapcigrp_ECP_00 on host sapeccprddb (wp 0)
ERROR       tskh_init: DpInitMpi
TIME        Sun Nov 16 05:13:07 2008
RELEASE     640
COMPONENT   Taskhandler
VERSION     1
RC          17
MODULE      thxxhead.c
LINE        9806
COUNTER     1
PfStatDisconnect: disconnect statistics
Entering TH_CALLHOOKS
ThCallHooks: call hook >SAP-Trace buffer write< for event BEFORE_DUMP
TrThHookFunc: called for WP dump
ThCallHooks: call hook >ThrSaveSPAFields< for event BEFORE_DUMP
ERROR => ThrSaveSPAFields: no valid thr_wpadm [thxxrun1.c   730]
ERROR => ThCallHooks: event handler ThrSaveSPAFields for event BEFORE_DUMP failed hxxtool3.c 254]
Entering ThSetStatError
Entering ThReadDetachMode
call ThrShutDown (1)...
***LOG Q02=> wp_halt, WPStop (Workproc 0 4000) [dpnttool.c   357]
Please suggest the solution
Thanks & Regards,
Rajesh

B18.8 DB upgrade from Patch level 12 to 15 Patch level

Dear Experts,
When I am trying to Upgrade database 8.8 PL 12 to SAP 8.8 PL 15 following are error.
I had completed the Downloading process of 8.8 patch level of 15.
WINRAR Diagnosis Error...................
! C:\Documents and Settings\amol(sap)\My Documents\Downloads\B18800_21-10003894.ZIP: The archive is either in unknown format or damaged
Please suggest.
Regards
Amol

Hi,
The setup file has corrupted so better you again download the file using SAP Download Manager.
*Close the thread if issue solved.
Regards
Jambulingam.P

Kernel upgrade - 640 patch level 247 - subsequent patches needed

Hi community,
I recently upgraded the kernel of our system SAP ECC 5.0 to kernel release 640 patch level 247
I used the the two files EXE and EXEDB as I usually do in this cases.
Unfortunately this kernel is affected with the problem described in note 1239685, which is critical for us.
To solve the problem SAP recommends upgrading kernel to patch level 252, which is not present in my files, but is present in the single disp+work package, which is level 273
What is the correct procedure in this case? I have to unpack only the disp+work package or all the archives listed in the download place?
Regards,
Valerio

Dear Valerio,
The packages SAPEXE.SAR and SAPEXEDB.SAR contain a complete set of database independent (SAPEXE.SAR) and database dependent (SAPEXEDB.SAR) executables. A kernel patch is delivered as a dw.SAR package. It is sufficient to extract the content of the dw.SAR into DIR_EXECUTABLE (normally /usr/sap/<SID>/SYS/exe/run for a 6.xx system on UNIX). Of course, this should be done while the system is down.
Best Regards,
Tim

How to check IGS version and procedure for upgrading IGS patch level

Hi all,
We are on BIW 3.5 .Iam not clear about how to check the version of IGS and its patch level .I went through various notes but still iam confused with tracing it , can someone plz help out?
Secondly want to upgrade IGS version i went through note 454042 but still confused with doing that , Can someone plz refer other notes or detailed procedure for upgrading IGS.
Our BIW Production and Test are on AIX and Development is on HP-Unix OS .
Points guaranteed for the same. Requested to revert at earliest as this is urgent .
Regards,
Saumya

Hi,
Check this link which may help u:
http://sap.ittoolbox.com/groups/technical-functional/sap-basis/igs-upgrade-1455477
The installation/upgrade procedures for the integrated IGS are as follows:
Integrated Version Installation
The integrated IGS is automatically installed with the SAP Web Application Server.
Integrated Version Upgrade
You find the upgrade files for the integrated IGS version on the SAP Service Marketplace:
http://service.sap.com/swdc ® Download ® Support Packages and Patches ® Entry by ApplicationGroup ® SAP Frontend Components ® SAP IGS ® SAP IGS .
There, you find the IGS executables and libraries (igsexe_.sar) as well as the IGS folder structure (igshelper_.sar) containing among others font files.
With the upgrade files of the executables and libraries, proceed exactly like you would with kernel patches (for example, extract the Archive to the same location). More information about kernel patches can be found in the related note 19466 in the section Copying and Installing a Patch.
The upgrade files for the IGS folder structure must be extracted to the instance directory (DIR_INSTANCE). More information can be found in note 1028690.
After a restart of the Web AS the new IGS is up and running.
Information about finding out your IGS patch level is provided in note 931900.
For an upgrade of an integrated IGS please also check note 896400.
For more info check this SAP Help doc:
http://help.sap.com/saphelp_nw04s/helpdata/en/4b/72d43ac66e1f08e10000000a114084/frameset.htm
Hope these helps u...
Regards,
KK.

List of notes after upgrading CIn patch level 22 to 27

Hi
We want upgrade system from 470 CIN patch level 22 to 470 CIN patch level 27.
i would like to know what will be the side effects and precautions to be taken for MM prospective wise. i also wanted know after upgradtion what all the notes required to be applied for new secondary and higher education cess. i need side effects of upgradation, precaustions and list of notes after upgradtion.

Dear,
You may have a look at the "Side Effects" report which is available in SAP Service Marketplace at http://service.sap.com/swdc-addinfo
-> SAP Support Packages in Detail
-> Side-Effects of SAP Notes
There you can define the source/target queues of support packages .
This report provides an overview of currently known side-effects of SAP Notes contained in a Support Package. The list also includes pointers to other SAP Notes, which are able to resolve undesired side-effects.
i hope that helps.
Lucio Rodrigues
SAP AGS

HP Quality Center Upgrade to Patch level 25

Hi @ all,
i did not find any better forum to post my questions... So i hope someone here can help me!
We are using the HP Quality Center with support from SAP.
We have Version 10.00 Patchlevel 19 installed.
Our Server is using
Windows 2003 as Operating system
and as DB we use SQL Server 2005 mit SP3.
Now we want to do an upgrade to Patchlevel 25 so that we can use
Windows 2008 R2 64 bit as operating system
and as DB SQL Server 2008 SP2.
This is our first upgrade on HPQC so I am searching for informations about how this will work!
Has anybody here experiences with this matter?
Thx in advanc and greetings
Ulrich Sahm

Hi Harmeet,
thanks for your answer. We would like to do following:
- we are now using a DB on SQL Server 2005 with HP QC Version 10.0 Patch 19
- we want to move to a DB on SQL Server 2008 SP2
- therefore it is necessary to upgrade to patch 25
So my question now is the order we have to do this. I would suppose the following order:
1. backup the existing databases (site admin & projects)
2. copy the repository folders of the projects
3. setup Windows 2008 R2 64 bit and SQL Server 2008 SP2 on existing server
4. restore the DB's on SQL Server 2008 SP2
5. install patch 25
Another possibility, that came up late was follwing: We Upgrade to HPQC 11 Patch 6. In thsi case i would suppose the following order:
1. backup the existing databases (site admin & projects)
2. copy the repository folders of the projects
3. setup Windows 2008 R2 64 bit and SQL Server 2008 SP2 on existing
servers
4. restore the DB on SQL Server 2008 SP2
5. uninstall HP QC version 10
6. install patch 6 of QC version 11.0 and assign the restored site
admin db during installation
7. do a mass upgrade to the project DB`s
Do you think we missed something or can we do it like this?
Thanks
Ulrich

How to upgrade IGS patch level

Hi,
Can anyone help in how to upgrade the igs patchs.
Regards,
SM

Hello,
Kindly download the igsexe_10-10003070.sar from http://service.sap.com/swdc Support Packages and Patches-> SAP Frontend Components->SAP IGS
Stop the SAP instance backup the run existing run folder. Use the same run folder where in you need to place the uncarred files of IGS.
Then restart the system. IGS will be upgraded to latest...
Thanks & Regards
Vivek

ITS patch level upgrading

Hi All,
I need to upgrade the patch level from 28 to33 according to SAP NOTE (1053737) so please let me know how to upgrade patch level on ITS and what is to be taken care while applying.
We need to apply because of some xss VULNERABILITY Attacks.
thanks in advance for the help,
Thanks&Regards,
Raj

Hello Raj,
To upgrade from ITS 6.20 patch 28 to 33 you will need to download the ITS 6.20 patch 33 installation file from the SAP Marketplace.
You may want to back up the services, templates, and mimes directories, but only if you have made changes. The exception is that you do NOT want to use your older (patch 28) ../templates/webgui ../templates/system ../its/mimes/system ../its/mimes/webgui in your new Patch 33 installation.
Edgar

Regarding the patch level..

Hi All,
This is krishna, I created two types of add-ons.. One is, In the exiting form only i created some more fields.. Another one is, newly created user defined forms and in which some fileds.. It is working fine.. Later i upgraded the patch level 5 to 40 for client requirement. When ever i upgrade that patch level, my second type of add-on are not working.. That is its not opening forms.. What happend i don't know..
If anybody knows the solution.. Plz let me know...
Regards,
krishna.v

Your question is more related to SDK for your own add-on. Please post it there.
Thanks.
Gordon

Patch level 19 not working

hi experts !!!
dis is vamsi krishna
,actually i want to upgrade my sap b1 2007 to patch level 19.
but when i install upgrade with patch level 19.it updates.
and when i start sap application its throws error saying that
"DATABASE IS NOT CONSISTENT , PLEASE CHECK THE LOG FILE FOR MORE INFORMATIION"
please experts , help me out if there's any solution

Hi,
Please restore the DB to where it was before you applied the patch.
Take the DB to a test environment and try the upgrade again? Also might be worthwhile to try a different patch to apply?
Finally contact SAP Support
Regards,
Paul

ECC patch level requirement for SNC 7.0 eph1

We are running ECC SR3 (w/o ehp) now and want to implement SNC 7.0 eph1.
Is there any official docuemnt to which I can refer regarding ECC hot package level requirement for SNC 7.0 eph1? We definately do NOT want to upgrade ECC patch level during SNC project.
If we must switch back to a lower version, such as SNC 7.0, is there a similar document?
Thanks in advance.
James

Dear James
See the SAP SNC Master Guide on SAP Service Marketplace at service.sap.com/instguides @ SAP Business Suite Applications @ SAP SCM @ SAP SNC
For SNC 7.01 go to using sap enhancment package for SAP SNC 7.0
For SNC 7.0 go to using SAP SNC 7.0
https://websmp101.sap-ag.de/support
At the bottom of the page, you can find master guide,
From page 27 section 2.3 Software Component Matrix, it is 90 page document
User details are required plz create one
You will find all the required information
Now if you want to check, realize scenario wise
In the same link, go to release & upgrade information-Product Availability Matrix and Realization Alternatives
THis is very good link
Notes
1180861 & 1281192 talks about 7.0
Best Regards
Vinod

Incorrect kernel patch level

Dear Experts,
I just upgraded kernel patch level to the latest one, i.e. 254, however the EWA report still read the old patch level (Your SAP kernel release (release 700, patch level 254) is not up-to-date).
Do we have to upgrade the ST_PI and/or PI_BASIS, the status is as follow:
SOLMAN:
PI_BASIS    2006_1_700   0008   SAPKIPYM08
ST-PI           2008_1_700 0000
Satellite:
PI_BASIS    2005_1_700 0010   SAPKIPYJ7A
ST-PI           2008_1_700 0000
Please advise.
Thank and Regards,
Rudi

Hi,
This "outdated check" is based on the compiling date of the
'disp+work package' of the kernel. The rules for how many days mean
outdated depend on the kernel release and the ST-SER Release and SP
running on the Solution Manager.
Please find below some corrections that extent the rules for beeing
up-to-date:
1076235 - RED Rating in Software Configuration, Kernel 700 old
1301137 - ST-SER 2008_2 SP02: Further Corrections
1304151 - Service Assistent: Adjustments for Kernel Check
You may want to have the latest ST-SER version in order
to ensure that the latest corrections are implemented in your system.
Hope this helps.
Cheers
SH

Upgrading to Patch Level 47

Similar Messages

Maybe you are looking for