UPnP doesn't work after enabling Hyper-V role on WS2012R2

Hi,
We have stream/media player which use File share on WS2012 R2. It uses UPnP protocol to connect on File Share and it works fine. But, after enabling Hyper-V role on that server machine, stream/media player can't connect anymore on network share, cannot see
any network computer, I would say master browser service is corrupted.
Do you have advice, how to use UPnP on server with enabled Hyper-V role and virtual network adapter?
Thank you in advance

Have you tried doing things in the opposite sequence?  Try first installing and configuring Hyper-V and the virtual switches you will be using.  Then install the media player.  Maybe the media player is losing track of things when its underlying
network is changed.
Of course, Microsoft does not recommend this configuration.  It does not recommend running any other service on a host that is running Hyper-V.  That does not immediately imply it will not work; just passing on that what you are doing is a non-recommended
configuration.
. : | : . : | : . tim

Similar Messages

  • [Solved] Network doesn't work after hibernate?

    Hello!  This is my first legit Linux install so excuse me if I'm a bit slow.  I installed Arch last night and everything went smoothly.  However, after I tested out hibernate on my machine, the network doesn't seem to work.  Just prior to the hibernate, I installed Pidgin and Skype but they worked alright, so I think that the hibernate caused a problem on eth0.
    I have an Asus P8Z68-V Pro motherboard with an Intel 82579V Gigabit Ethernet Controller that's using the e1000e driver.  Running "dmesg | grep e1000e" says that it is up.
    I'm not entirely clear here, but from reading, I think that I have several ways of connecting to the network, including network, dhcpcd, networkmanager, and wicd.  I am using wicd so I did the following (or at least I think I am only using wicd):
    #rc.d stop network
    #rc.d stop dhcpcd
    #rc.d stop networkmanager
    Similarly, I put a ! in front of network in rc.conf:
    # /etc/rc.conf - Main Configuration for Arch Linux
    # LOCALIZATION
    # LOCALE: available languages can be listed with the 'locale -a' command
    # DAEMON_LOCALE: If set to 'yes', use $LOCALE as the locale during daemon
    # startup and during the boot process. If set to 'no', the C locale is used.
    # HARDWARECLOCK: set to "", "UTC" or "localtime", any other value will result
    # in the hardware clock being left untouched (useful for virtualization)
    # Note: Using "localtime" is discouraged, using "" makes hwclock fall back
    # to the value in /var/lib/hwclock/adjfile
    # TIMEZONE: timezones are found in /usr/share/zoneinfo
    # Note: if unset, the value in /etc/localtime is used unchanged
    # KEYMAP: keymaps are found in /usr/share/kbd/keymaps
    # CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
    # CONSOLEMAP: found in /usr/share/kbd/consoletrans
    # USECOLOR: use ANSI color sequences in startup messages
    LOCALE="en_US.UTF-8"
    DAEMON_LOCALE="no"
    HARDWARECLOCK="UTC"
    TIMEZONE="America/New_York"
    KEYMAP="us"
    CONSOLEFONT=
    CONSOLEMAP=
    USECOLOR="yes"
    # HARDWARE
    # MODULES: Modules to load at boot-up. Blacklisting is no longer supported.
    # Replace every !module by an entry as on the following line in a file in
    # /etc/modprobe.d:
    # blacklist module
    # See "man modprobe.conf" for details.
    MODULES=()
    # Udev settle timeout (default to 30)
    UDEV_TIMEOUT=30
    # Scan for FakeRAID (dmraid) Volumes at startup
    USEDMRAID="no"
    # Scan for BTRFS volumes at startup
    USEBTRFS="no"
    # Scan for LVM volume groups at startup, required if you use LVM
    USELVM="no"
    # NETWORKING
    # HOSTNAME: Hostname of machine. Should also be put in /etc/hosts
    HOSTNAME="Vicious"
    # Use 'ip addr' or 'ls /sys/class/net/' to see all available interfaces.
    # Wired network setup
    # - interface: name of device (required)
    # - address: IP address (leave blank for DHCP)
    # - netmask: subnet mask (ignored for DHCP) (optional, defaults to 255.255.255.0)
    # - broadcast: broadcast address (ignored for DHCP) (optional)
    # - gateway: default route (ignored for DHCP)
    # Static IP example
    # interface=eth0
    # address=192.168.0.2
    # netmask=255.255.255.0
    # broadcast=192.168.0.255
    # gateway=192.168.0.1
    # DHCP example
    # interface=eth0
    # address=
    # netmask=
    # gateway=
    interface=eth0
    address=
    netmask=
    broadcast=
    gateway=
    # Setting this to "yes" will skip network shutdown.
    # This is required if your root device is on NFS.
    NETWORK_PERSIST="no"
    # Enable these netcfg profiles at boot-up. These are useful if you happen to
    # need more advanced network features than the simple network service
    # supports, such as multiple network configurations (ie, laptop users)
    # - set to 'menu' to present a menu during boot-up (dialog package required)
    # - prefix an entry with a ! to disable it
    # Network profiles are found in /etc/network.d
    # This requires the netcfg package
    #NETWORKS=(main)
    # DAEMONS
    # Daemons to start at boot-up (in this order)
    # - prefix a daemon with a ! to disable it
    # - prefix a daemon with a @ to start it up in the background
    # If something other takes care of your hardware clock (ntpd, dual-boot...)
    # you should disable 'hwclock' here.
    DAEMONS=(hwclock syslog-ng dbus !network netfs crond wicd)
    Restarting eth0 through wicd-cli still did not work.  I also tried resuscitating the network via instructions on the configure network page before trying to focus solely on wicd.
    I found a few similar problems on the forums by searching "wicd hibernate" and tried several solutions but they did not work.  Several problems seem to be that the network doesn't work after a suspend because I guess the stuff in RAM did not get saved?  But people were able to restart the network by running "/usr/lib/wicd/autoconnect.py" and I wasn't able to get this to work.  As a final effort, I added "resume" into mkinitcpio.conf and placed the machine into sleep again to see if it may magically reset something but of course this did not happen .
    mkinitcpio.conf:
    # vim:set ft=sh
    # MODULES
    # The following modules are loaded before any boot hooks are
    # run. Advanced users may wish to specify all system modules
    # in this array. For instance:
    # MODULES="piix ide_disk reiserfs"
    MODULES=""
    # BINARIES
    # This setting includes any additional binaries a given user may
    # wish into the CPIO image. This is run first, so it may be used to
    # override the actual binaries used in a given hook.
    # (Existing files are NOT overwritten if already added)
    # BINARIES are dependency parsed, so you may safely ignore libraries
    BINARIES=""
    # FILES
    # This setting is similar to BINARIES above, however, files are added
    # as-is and are not parsed in any way. This is useful for config files.
    # Some users may wish to include modprobe.conf for custom module options
    # like so:
    # FILES="/etc/modprobe.d/modprobe.conf"
    FILES=""
    # HOOKS
    # This is the most important setting in this file. The HOOKS control the
    # modules and scripts added to the image, and what happens at boot time.
    # Order is important, and it is recommended that you do not change the
    # order in which HOOKS are added. Run 'mkinitcpio -H <hook name>' for
    # help on a given hook.
    # 'base' is _required_ unless you know precisely what you are doing.
    # 'udev' is _required_ in order to automatically load modules
    # 'filesystems' is _required_ unless you specify your fs modules in MODULES
    # Examples:
    ## This setup specifies all modules in the MODULES setting above.
    ## No raid, lvm2, or encrypted root is needed.
    # HOOKS="base"
    ## This setup will autodetect all modules for your system and should
    ## work as a sane default
    # HOOKS="base udev autodetect pata scsi sata filesystems"
    ## This is identical to the above, except the old ide subsystem is
    ## used for IDE devices instead of the new pata subsystem.
    # HOOKS="base udev autodetect ide scsi sata filesystems"
    ## This setup will generate a 'full' image which supports most systems.
    ## No autodetection is done.
    # HOOKS="base udev pata scsi sata usb filesystems"
    ## This setup assembles a pata mdadm array with an encrypted root FS.
    ## Note: See 'mkinitcpio -H mdadm' for more information on raid devices.
    # HOOKS="base udev pata mdadm encrypt filesystems"
    ## This setup loads an lvm2 volume group on a usb device.
    # HOOKS="base udev usb lvm2 filesystems"
    HOOKS="base udev autodetect pata scsi sata resume filesystems usbinput"
    # COMPRESSION
    # Use this to compress the initramfs image. With kernels earlier than
    # 2.6.30, only gzip is supported, which is also the default. Newer kernels
    # support gzip, bzip2 and lzma. Kernels 2.6.38 and later support xz
    # compression.
    #COMPRESSION="gzip"
    #COMPRESSION="bzip2"
    #COMPRESSION="lzma"
    #COMPRESSION="xz"
    #COMPRESSION="lzop"
    # COMPRESSION_OPTIONS
    # Additional options for the compressor
    #COMPRESSION_OPTIONS=""
    Not sure if my fstab.conf is useful but if this has something to do with settings getting "lost" in swap, here it is.  Linux is on an SSD and HDD (sda and sdc) and Windows 7 is on a HDD (sdb).
    fstab.conf:
    # /etc/fstab: static file system information
    # <file system> <dir> <type> <options> <dump> <pass>
    none /tmp tmpfs nodev,nosuid,noatime,size=2000M,mode=1777 0 0
    /dev/sda1 / ext4 defaults,noatime,discard 0 1
    /dev/sda2 /home ext4 defaults,noatime,discard 0 2
    /dev/sdc1 /boot ext4 defaults 0 1
    /dev/sdc2 /var ext4 defaults 0 0
    /dev/sdc3 swap swap defaults 0 0
    /dev/sdc4 /media/data ext4 defaults 0 0
    shm /dev/shm tmpfs nodev,nosuid,size=10G 0 0
    Is wicd causing these problems or did I configure something else improperly?  Would appreciate any help to get eth0 up again!
    Last edited by TheBigCow7 (2011-09-13 17:57:20)

    Ok, I think I've made some progress!  Hibernate definitely affects my network connection.  Could this be a kernel 3.0 problem?
    I noticed that ifconfig showed eth0 without an inet addr, just an inet6 addr for the longest time.  e1000e seemed to be loading up ok.  I'm not certain here, but I think that meant the dhcp settings didn't stick, or something along those lines.
    Trying to use dhcpcd like the instructions here did not work.  By some chance, one attempt did work and while it did, I downloaded and installed dhclient.  After that one successful attempt, renewing the DHCP lease via dhcpcd did not work again.
    Luckily though, I found that running "dhclient eth0" worked.  My DHCP settings seemed to have somehow gotten messed up after my initial, problematic hibernate to the point where none would stick, even after a reboot.  Manually typing in "dhclient eth0" would get eth0 working, so I decided to add it to the bottom of /etc/rc.local, like in the example on the networking page.
    Now, eth0 works after a boot.  However, after the daemons load up during the boot process, my computer takes a long time to get to the login prompt (this is relatively speaking, since I am on a SSD and the boot process used to be blazing fast before).  I'm pretty sure it's because I added "dhclient eth0" to /etc/rc.local.
    I should say that even with these changes, after a hibernate, my eth0 still does not work and if it weren't for the edit to /etc/rc.local, eth0's inet settings would still not stick after a reboot (that is to say, the hibernate does do something to my network settings). 
    Is this the correct/most efficient way to fix my DHCP problem?  Can I fix my "eth0 after hibernate" issue?  Also, can I make my DHCP settings boot up without changes to /etc/rc.local so that I can get a fast boot again (still not sure how it was able to work before without my edit)?

  • Home sharing doesn't work after updating itunes to 10.6.40

    Hi
    Just update my itunes to 10.6.40 and ipad1/iphone4 to 5.1.
    The home sharing doesn't appear after enable it and both remote app (ipad and iphone) don't work!
    Now, my ipad doesn't sync thru wifi and my iphone 4 sync thru wifi even when not charging.
    Please help
    Regards
    Pedro Silva

    Thanks! I didn't realise there was a specific forum for Home Sharing... found it now and will repost there.

  • M3800 Developer Edition: wifi doesn't work after sleep

    I have an M3800 Developer Edition (2015 model). Ubuntu is factory-installed 14.04, with hardware enablement stack installed. Recently (past 1-2 weeks) wifi doesn't work after sleep (lid closed or open doesn't matter), and only rebooting gets in back. Tried rmmod and modprobe with no success. Has anyone else seen this, and/or are you aware of any open bug(s) for this?
    Relevant ouput:
    lsmod when problem exists:
    iwlmvm                217725  0
    mac80211              652718  1 iwlmvm
    iwlwifi               179412  1 iwlmvm
    cfg80211              494362  3 iwlwifi,mac80211,iwlmvm
    rfkill list when problem exists:
    1: phy0: Wireless LAN
            Soft blocked: no
            Hard blocked: no
    3: hci0: Bluetooth
            Soft blocked: no
            Hard blocked: no
    rmmod the above, then modprobe iwlwifi. Does not fix problem, only rebooting does:
    May  4 08:23:14 jonathan-m3800 kernel: [69089.189614] cfg80211: Calling CRDA to update world regulatory domain
    May  4 08:23:14 jonathan-m3800 kernel: [69089.192181] cfg80211: World regulatory domain updated:
    May  4 08:23:14 jonathan-m3800 kernel: [69089.192184] cfg80211:  DFS Master region: unset
    May  4 08:23:14 jonathan-m3800 kernel: [69089.192185] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
    May  4 08:23:14 jonathan-m3800 kernel: [69089.192187] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
    May  4 08:23:14 jonathan-m3800 kernel: [69089.192188] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
    May  4 08:23:14 jonathan-m3800 kernel: [69089.192189] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm), (N/A)
    May  4 08:23:14 jonathan-m3800 kernel: [69089.192190] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
    May  4 08:23:14 jonathan-m3800 kernel: [69089.192191] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
    May  4 08:23:14 jonathan-m3800 kernel: [69089.204141] Intel(R) Wireless WiFi driver for Linux, in-tree:
    May  4 08:23:14 jonathan-m3800 kernel: [69089.204143] Copyright(c) 2003- 2014 Intel Corporation
    May  4 08:23:14 jonathan-m3800 kernel: [69089.204414] iwlwifi 0000:06:00.0: irq 48 for MSI/MSI-X
    May  4 08:23:14 jonathan-m3800 kernel: [69089.204904] iwlwifi 0000:06:00.0: loaded firmware version 25.228.9.0 op_mode iwlmvm
    May  4 08:23:14 jonathan-m3800 kernel: [69089.207709] iwlwifi 0000:06:00.0: Detected Intel(R) Dual Band Wireless AC 7260, REV=0x144
    May  4 08:23:14 jonathan-m3800 kernel: [69089.207790] iwlwifi 0000:06:00.0: L1 Enabled - LTR Enabled
    May  4 08:23:14 jonathan-m3800 kernel: [69089.208150] iwlwifi 0000:06:00.0: L1 Enabled - LTR Enabled
    May  4 08:23:14 jonathan-m3800 kernel: [69089.392408] ieee80211 phy0: Selected rate control algorithm 'iwl-mvm-rs'
    May  4 08:23:14 jonathan-m3800 NetworkManager[901]:    SCPlugin-Ifupdown: devices added (path: /sys/devices/pci0000:00/0000:00:1c.2/0000:06:00.0/net/wlan0, iface: wlan0)
    May  4 08:23:14 jonathan-m3800 NetworkManager[901]:    SCPlugin-Ifupdown: device added (path: /sys/devices/pci0000:00/0000:00:1c.2/0000:06:00.0/net/wlan0, iface: wlan0): no ifupdown configuration found.
    May  4 08:23:14 jonathan-m3800 NetworkManager[901]: <info> (wlan0): using nl80211 for WiFi device control
    May  4 08:23:14 jonathan-m3800 NetworkManager[901]: <info> (wlan0): driver supports Access Point (AP) mode
    May  4 08:23:14 jonathan-m3800 NetworkManager[901]: <info> (wlan0): new 802.11 WiFi device (driver: 'iwlwifi' ifindex: 4)
    May  4 08:23:14 jonathan-m3800 NetworkManager[901]: <info> (wlan0): exported as /org/freedesktop/NetworkManager/Devices/2
    May  4 08:23:14 jonathan-m3800 NetworkManager[901]: <info> rfkill5: found WiFi radio killswitch (at /sys/devices/pci0000:00/0000:00:1c.2/0000:06:00.0/ieee80211/phy0/rfkill5) (driver iwlwifi)
    May  4 08:23:16 jonathan-m3800 ModemManager[852]: <warn>  Couldn't find support for device at '/sys/devices/pci0000:00/0000:00:1c.2/0000:06:00.0': not supported by any plugin
    lspci:
    06:00.0 Network controller: Intel Corporation Wireless 7260 (rev 6b)
    After reboot:
    lsmod |grep -i iwl:
    iwlmvm                217725  0
    mac80211              652718  1 iwlmvm
    iwlwifi               179412  1 iwlmvm
    cfg80211              494362  3 iwlwifi,mac80211,iwlmvm
    rfkill list after reboot:
    0: nfc0: NFC
            Soft blocked: no
            Hard blocked: no
    1: phy0: Wireless LAN
            Soft blocked: no
            Hard blocked: no
    2: hci0: Bluetooth
            Soft blocked: no
            Hard blocked: no

    Wi-Fi still not reconnecting after sleep 
    http://forums.macrumors.com/showthread.php?t=1229591

  • Macbook air adoble flash player doesn't work after installation

    macbook air adobe flash player doesn't work after installation

    If you're sure you've installed the latest version of Flash, take each of the following steps that you haven't already tried. After each step, relaunch Safari and test. For a "missing plug-in" error, start with Step 7. Back up all data before making any changes.
    Step 1
    You might have to log out or reboot before a Flash update takes effect.
    Step 2
    In the Safari preference window, select
    Privacy ▹ Remove All Website Data
    Close the window. Then select
     ▹ System Preferences… ▹ Flash Player ▹ Advanced
    and click Delete All. Close the preference pane.
    Step 3
    If you're only having trouble with YouTube videos, log in to YouTube and load this page. You may see a link with the text "Leave the HTML5 Trial." If so, click that link.
    Step 4
    If you get a warning of a "blocked" or "outdated" plug-in, then from the menu bar select
     ▹ System Preferences… ▹ Flash Player ▹ Advanced
    and click Check Now. Quit and relaunch the browser.
    If the warning persists, triple-click anywhere in the line below on this page to select it:
    /System/Library/CoreServices/CoreTypes.bundle/Contents/Resources
    Right-click or control-click the highlighted text and select
    Services ▹ Open
    from the contextual menu.* A folder should open. Inside it, there should be a file named "XProtect.meta.plist". If that file is missing and you know why it's missing, restore it from a backup or copy it from another Mac running the same version of OS X. Otherwise, reinstall OS X.
    *If you don't see the contextual menu item, copy the selected text to the Clipboard by pressing the key combination command-C. In the Finder, select
    Go ▹ Go to Folder...
    from the menu bar and paste into the box that opens (command-V). You won't see what you pasted because a line break is included. Press return.
    Step 5
    Open this folder as in Step 4:
    /Library/Internet Plug-Ins
    Delete the following item, or anything with a similar name, if present:
    Flash Player (failing).plugin  
    You may be prompted for your login password.
    Step 6
    Re-download and reinstall Flash. Download it from the domain "get.adobe.com". Don't click a link from any other website, including this one, because you can't trust links. They may be an attempt to trick you into installing malware masquerading as Flash. Type the address into the browser window. Never download a Flash update from anywhere else.
    Step 7
    If you get a "missing plug-in" error, select
    Safari ▹ Preferences... ▹ Security
    from the Safari menu bar and check the box marked
    Allow (or Enable) plug-ins
    Then click the button marked
    Manage Website Settings...
    if present and make sure that the website is not blocked for Flash.
    Step 8
    Select
    Safari ▹ Preferences... ▹ Extensions
    from the Safari menu bar. If any extensions are installed, disable them.

  • IMac - Display doesn´t work after restart

    My iMac 21 Display doesn´t work after restart. If I turn it off and 1 hour later I want use it again the iMac shows the white screen with the mac logo and then the display goes off. I connected an external display to check if the iMac was ON and with the external display I can login and do everything but the iMac Display doesn´t work .
    If I turn it off and wait 3 or 4 hours  and then turn it back on the display works OK.
    This is very strange behavior I have spent hours and hours trying to fine the solution or a similar issue but nothing so I am looking help here at apple.com
    BTW When I bougth the iMac 21 there were some spots over the display so the display was replaced by the provider. The warranty has expired by now.

    To tell you the truth, I don't know if they have to repalce the LCD panel or what they do for a bad backlight. In this reality of block or assembly replacement it probably involves repalcing the panel and not the backlight component. Don't know what it would cost. You'd have to ask that of a service center.

  • Touch ID doesn't work after ios 7.1.1 update

    Touch id doesn't work after ios 7.1.1 update..
    Why????

    After IOS update, you first have to use passcode.
    Passcode is needed when
    After restarting your iPhone 5s
    When more than 48 hours have elapsed from the last time you unlocked your iPhone 5s
    To enter the Touch ID & Passcode setting

  • Mail server doesn't work after upgrading from SL to ML

    My Mail server doesn't work after upgrading from SL to ML
    Mail client connects with the Mail Server wich seems to run but then they can't receive any email...
    the problem seems to be related with dovecot ... in my smtp log i get this:
    relay=dovecot, delay=324, delays=324/0.02/0/0.01, dsn=4.3.0, status=deferred (temporary failure. Command output: pipe: fatal: pipe_command: execvp /usr/libexec/dovecot/deliver: Permission denied
    I have to say that in the usr/libexec there wasn't the dovecot directory so I just tried to create one but with no luck
    Any Ideas?
    Cheers
    Carlo
    This is my postconf -n info:
    server:Data admin$ postconf -n
    biff = no
    command_directory = /usr/sbin
    config_directory = /Library/Server/Mail/Config/postfix
    content_filter = smtp-amavis:[127.0.0.1]:10024
    daemon_directory = /usr/libexec/postfix
    data_directory = /Library/Server/Mail/Data/mta
    debug_peer_level = 2
    debugger_command = PATH=/bin:/usr/bin:/usr/local/bin:/usr/X11R6/bin xxgdb $daemon_directory/$process_name $process_id & sleep 5
    dovecot_destination_recipient_limit = 1
    enable_server_options = yes
    header_checks = pcre:/etc/postfix/custom_header_checks
    html_directory = /usr/share/doc/postfix/html
    imap_submit_cred_file = /Library/Server/Mail/Config/postfix/submit.cred
    inet_interfaces = all
    inet_protocols = ipv4
    mail_owner = _postfix
    mailbox_size_limit = 0
    mailbox_transport =
    mailq_path = /usr/bin/mailq
    manpage_directory = /usr/share/man
    maps_rbl_domains =
    message_size_limit = 20971520
    mydestination = $myhostname, localhost.$mydomain, localhost
    mydomain = moremoremore.it
    mydomain_fallback = localhost
    myhostname = server.moremoremore.it
    mynetworks = 127.0.0.0/8,192.168.178.0/24
    newaliases_path = /usr/bin/newaliases
    queue_directory = /Library/Server/Mail/Data/spool
    readme_directory = /usr/share/doc/postfix
    recipient_delimiter = +
    relayhost = mail.mclink.it
    sample_directory = /usr/share/doc/postfix/examples
    sendmail_path = /usr/sbin/sendmail
    setgid_group = _postdrop
    smtp_sasl_auth_enable = no
    smtp_sasl_password_maps =
    smtpd_client_restrictions = permit_mynetworks permit_sasl_authenticated reject_rbl_client zen.spamhaus.org permit
    smtpd_enforce_tls = no
    smtpd_helo_required = yes
    smtpd_helo_restrictions = reject_invalid_helo_hostname reject_non_fqdn_helo_hostname
    smtpd_pw_server_security_options = cram-md5,gssapi
    smtpd_recipient_restrictions = permit_sasl_authenticated permit_mynetworks reject_unauth_destination check_policy_service unix:private/policy permit
    smtpd_sasl_auth_enable = yes
    smtpd_tls_CAfile = /etc/certificates/server.moremoremore.it.A358901573EE7B9B4D489725407934780D24D5 36.chain.pem
    smtpd_tls_cert_file = /etc/certificates/server.moremoremore.it.A358901573EE7B9B4D489725407934780D24D5 36.cert.pem
    smtpd_tls_exclude_ciphers = SSLv2, aNULL, ADH, eNULL
    smtpd_tls_key_file = /etc/certificates/server.moremoremore.it.A358901573EE7B9B4D489725407934780D24D5 36.key.pem
    smtpd_use_pw_server = yes
    smtpd_use_tls = yes
    tls_random_source = dev:/dev/urandom
    unknown_local_recipient_reject_code = 550
    virtual_alias_maps =
    server:Data admin$

    if this could help:
    mail:setStateVersion = 1
    mail:readWriteSettingsVersion = 1
    mail:connectionCount = 11
    mail:servicePortsRestrictionInfo = _empty_array
    mail:protocolsArray:_array_index:0:status = "ON"
    mail:protocolsArray:_array_index:0:kind = "INCOMING"
    mail:protocolsArray:_array_index:0:protocol = "IMAP"
    mail:protocolsArray:_array_index:0:state = "RUNNING"
    mail:protocolsArray:_array_index:0:error = ""
    mail:protocolsArray:_array_index:1:status = "ON"
    mail:protocolsArray:_array_index:1:kind = "INCOMING"
    mail:protocolsArray:_array_index:1:protocol = "POP3"
    mail:protocolsArray:_array_index:1:state = "RUNNING"
    mail:protocolsArray:_array_index:1:error = ""
    mail:protocolsArray:_array_index:2:status = "ON"
    mail:protocolsArray:_array_index:2:kind = "INCOMING"
    mail:protocolsArray:_array_index:2:protocol = "SMTP"
    mail:protocolsArray:_array_index:2:state = "RUNNING"
    mail:protocolsArray:_array_index:2:error = ""
    mail:protocolsArray:_array_index:3:status = "ON"
    mail:protocolsArray:_array_index:3:kind = "OUTGOING"
    mail:protocolsArray:_array_index:3:protocol = "SMTP"
    mail:protocolsArray:_array_index:3:state = "RUNNING"
    mail:protocolsArray:_array_index:3:error = ""
    mail:protocolsArray:_array_index:4:status = "OFF"
    mail:protocolsArray:_array_index:4:kind = "INCOMING"
    mail:protocolsArray:_array_index:4:protocol = "Junk_mail_filter"
    mail:protocolsArray:_array_index:4:state = "STOPPED"
    mail:protocolsArray:_array_index:4:error = ""
    mail:protocolsArray:_array_index:5:status = "OFF"
    mail:protocolsArray:_array_index:5:kind = "INCOMING"
    mail:protocolsArray:_array_index:5:protocol = "Virus_scanner"
    mail:protocolsArray:_array_index:5:state = "STOPPED"
    mail:protocolsArray:_array_index:5:error = ""
    mail:startedTime = "2013-01-21 21:18:32 +0000"
    mail:logPaths:IMAP Log = "/Library/Logs/Mail/mailaccess.log"
    mail:logPaths:Server Log = "/Library/Logs/Mail/mailaccess.log"
    mail:logPaths:POP Log = "/Library/Logs/Mail/mailaccess.log"
    mail:logPaths:SMTP Log = "/var/log/mail.log"
    mail:logPaths:Migration Log = "/Library/Logs/MailMigration.log"
    mail:logPaths:Virus Log = "/Library/Logs/Mail/clamav.log"
    mail:logPaths:Amavisd Log = "/Library/Logs/Mail/amavis.log"
    mail:logPaths:Virus DB Log = "/Library/Logs/Mail/freshclam.log"
    mail:imapStartedTime = "2013-01-21 21:18:34 +0000"
    mail:servicePortsAreRestricted = "NO"
    mail:state = "RUNNING"
    mail:postfixStartedTime = "2013-01-21 21:18:32 +0000"

  • Why tethering with USB cable doesn't work after IOS6.0 update?

    why tethering with USB cable doesn't work after IOS 6.0 update?

    Try updating the carrier settings, if that doesn't do it try following along with this Apple doc -> iOS: Troubleshooting Personal Hotspot

  • My cable doesn't work after two months I bought my iphone 6. Whether could I get a new one from apple free charge?

    my cable doesn't work after two months I bought my iphone 6. Whether could I get a new one from apple free charge?

    It's covered under the same warranty as the phone. So long as it's not physically damaged, they should replace it for you.

  • Fit the window with mouse doesn't work after new update 10.9.2

    Hi, I could fit a windows using my mouse wheel or two finger(on trackpad), doesn't work after I set up new Mavericks update(10.9.2) I'm using Haswell rMBP. Can anyone help me please? Thanks a lot. (Also, minimize with mouse wheel doesn't work too.)

    Doesn't anyone having this issue?

  • Condition doesn't work after transport to QAS system.

    Hi all:
          the condition doesn't work after the workflow transported to QAS system.  the workflow designed has a constraint that only the creation of the document of Type M4 can trigger the workflow, but creation of Type M5 document can also trigger the workflow, could you please tell me the possible reason?
    Thank you very much

    Hi,
    Once Try checking as pavan suggested whether the Customizing requested is transported.
    To Maintain Workflow start conditions you can also maintain through SWB_COND and ensure its transported.
    Regards
    Narin

  • Sirius Internet Radio doesn't work after Snow Leopard

    Sirius Internet Radio doesn't work after I installed Snow Leopard. It works on my Firefox. I emptied the cache on my Safari, but still nothing. Any solutions?

    The reason why Sirius Radio online won't work with Safari anymore is because Sirius radio online is only supported by a 32-bit browser. Snow Leopard and all its applications are 64-bit. The best solution is to use firefox. If you still insist on using safari..... Go to adobe.com reinstall adobe flash player. Install/update Flip4Mac. Go to setting for Flip4Mac and check off all the options under the browser tab. Then when you go into Sirius Radio online, you will get an error message, just click okay. Then when you click a station, a quicktime player will come up and you will be able to listen to sirius online radio.
    [email protected]

  • My SuperDrive doesn't work after Lion update

    My Superdrive doesn't work after Lion update, i have tried a few solutions that i found in forums, but nothing seems to work, please help me shed some light on my problem.
    Thanks

    I too have had the problem since updating to Lion.  My superdrive isn't even recognized.  I have repaid hard disk permissions and also reset PRAM.  Sure wish I had a fix. 

  • HT4623 Landscape feature on iphone doesn't work after OS 7 download.  HELP.

    The landscape feature on iphone doesn't work after OS 7 download.  How do i fix it?!

    Swipe up from the bottom.  Control center should cover about 2/3 of the screen.  At the top right of control center is a circle with a lock in it.  If that lock is closed, tap to open it.

Maybe you are looking for