URGENCY! problem with printing with Epson matrix printer

I have Epson printers : LX-300+ and FX-980.
I want to print a report from an Oracle application on continous paper.My report is one page.
The printer is set with:
auto tear off=on
page length for tractor=12 (inches)
At the first print job the paper advanced until the perforation line .
At the next print job the paper advanced until 1 cm before the perforation line and this is my problem.
In my report I set in the main section the following dimensions :
Width=20.5
Height=30.4
Character Mode
Report width=132
Report Height=85
What can I do so at every print job my paper advanced correctly until the perforation line?
Plese help me! Thanks a lot!

Cristina,
Same/similar issue for Epson printer has been fixed in reports 6i patch7.
I would suggest you to apply the latest reports 6i patch (patch 12)
Thanks
The Oracle Reports Team

Similar Messages

  • Right side Text not printing in Dot Matrix Print

    Hi Gurus,
    When i take print of the smartform with Laser Jet Printer its comming fine , but when i print using Dot Matrix Printer the text at right side is not printing.
    Printer model : Epson DFX-5000+
    Can any one tell me how to resolve this..
    Thanks
    Ganesh

    hi ,
      SAPWIN Drivers which support those Epson printers  check in SAP (windows support )
      These will solve your Problem  .
    Regards
    Deepak.

  • Horizontal Vertical and logo is not printed in dot matrix printer

    Hi All
    i am printing a smartform in dot matrix printer
    the form has horizontal vertical line
    table lines , and logo
    but when i print in Dot matrix printer
    the line and logo is not display
    Please say me how i design for it
    wheather It is printer or smartform design problem?
    Regard
    Riten

    Hi riten,
    The Printer settings is not supporting the horizontal and vertical line ..check with the basis team for the printer settings.
    Regards,
    Sravanthi

  • Printing in Dot Matrix Printer

    Hi to all,
      As we know that the dos matrix printer supports dos prompt and thus printing speed and 
    life of the printing head is comparatively more than what we print the same in graphical format.
      So when I tried to print from SAP Bone in dot matrix printer, the printing speed is very slow and quality of printout is not good enough.
      Any clarifications on this regard would prove very helpful to me.
    Regards,
    Aditya
    Consultant Business solutions.

    Do you use one of this printer types:
    Dot Matrix, Printer, Needle Printer, Citizen ProDot 300 , Oki Microline
    , Epson FX880, Epson FX890 ?
    Here the stepwise I have tried :
    In order to print using Dot Matrix printers, follow the below
    instructions:
       1. Run SAP Business One.
       2. Click the upper menu 'File' and select 'Page Setup'.
       3. The Print Setup window opens. Under 'Paper', in the field 'Size', select 'Letter' from the drop down menu.
       4. Click OK to confirm your selection.
       5. On your desktop, click Start => Settings => Printers.
       6. Right click on the required Dot Matrix printer and select 'Printing Preferences...'.
       7. Click the 'Paper/Quality' tab page and click the 'Advanced' pushbutton.
       8. Under'Paper/Output'=> 'Paper Size', click on the underlined paper size(e.g. A4) and select 'Letter' from the drop down menu.
    Note that if you leave the value 'A4', each page will be spreaded over 2 pages when printing using Dot Matrix printers.
       1. Under 'Graphic'=> 'Print Quality', click on the underlined value (e.g. 230X250 dots per inch) and select '120X144 dots per inch' from thedrop down menu.
    Note that in case the value '120X144' is not available you should select a similar value from the list.
    After you do the stepwise, I am sure there will no problem any more. The slowly printing mostly caused by printer type and your hardware specifications for example your LAN, etc..
    good luck...
    Rgds,
    null

  • Printing on Dot Matrix Printer

    Hi
    I am using JPS for printing, but to print on dot matrix printer, conventionally you print character at perticular row & col. Using Java Print Services how can I print a report to Dot Matrix Printer.
    Thanks in Advance

    Anybody knows I am also facing same Problem.
    Thanx

  • Draft / fast Printing on Dot Matrix Printer(s) from Windows

    Dear all,
    we need to print all documents in Draft / fast Printing on Dot Matrix Printer(s). how we can print quick draft mode. we are using SAP PL43. from where we can download draft 10cpi fonts.
    Regds,
    samapth

    Draft mode is not by font.  It is a specific printer mode.  If you can not manually setup the mode, B1 may not have any abilities to print in this mode.
    Thanks,
    Gordon

  • CS 5.1 won't print 13x19 print on Epson R1800 printer.  Other sizes will print.  Suggestion?

    CS 5.1 won't print 13x19 print on Epson R1800 printer.  Other sizes will print.  Epson offered suggestions and said it relats to Photoshop.  Anyone else have this issue?

    You'll get better answers on that in the proper PS forum...
    Mylenium

  • Problem with countinuous paper printing in dot matrix printer

    Hi All,
      I have problem with dot matrix printer (Devise Type EPESCP) while printing continuos printing. If  i am printing 2 or more than that prints at a time, 2nd page is printing 5 lines up.
    I have developed one smartform for this and i have used A4 size page format.
    I have tried to change the Printer initialization code to 86 lines for DINA4.  Still no change in continuous printing.
         Printer initialization
         Reset after exit
         Cover page
         First Page
         Start of even page
         Start of odd page
         Start of page
         End of first page
         End of even page
         End of odd page
         End of page
         Start of line on an even page
         Start of line on an odd page
         Start of line
         End of line on an even page
         End of line on odd page
         End of line
    Printer initialization
    # reset
    \e\0x40
    # select character table 3 -> PC 437 character set
    \e\0x74\0x03
    # set line spacing 6 LPI
    \e\0x32
    # set page length 86 lines
    \e\0x43\0x46
    # cancel bottom margin
    \e\0x4F
    # set left margin to 0
    \e\0x6C\0x00
    # select LQ quality
    \e\0x78\0x01
    # select non-proportional spacing
    \e\0x70\0x00
    Can any one help me.
    Thanks,
    Vishnu

    Hi Vishnu,
    Above you have the following commands:
    set line spacing 6 LPI
    \e\0x32
    set page length 86 lines
    \e\0x43\0x46
    46 HEX = 70
    So the above settings mean 70 lines at 6 LPI = 11.66 inches.
    So is the paper length 11.66 inches? If not, you should adjust the settings accordingly.
    Regards,
    Aidan

  • Problem printing on dot-matrix printer with continuous paper

    Post Author: kdebruyckere
    CA Forum: .NET
    Hi,
    We're currently developping an .net application for a customer of ours in VS2005 (c#). I used crystal reports for VS2005 to create an invoice.
    The invoices have to be printed on a dot-matrix printer with continuous paper (Brother M-4318). When an invoice is only one page long, there's no problem. Even when printing several sigle-page invoices after another, all goes fine. The problem occurs when an invoice is more then one page longe. The first page comes out correctly, but on the following pages everything moves ca. 3 mm upwards (3 mm on the second page, 6 mm on the third page, and so on...). On the report 'Design > Printer Setup', I selected the right printer, the right paper size, ... On the report there's a page header (consisting of two sections), and there's a page footer that is only printed on the last page, but there are no report header and no report footer.
    I can not figure out what seems to be the problem. Has anyone else had this or a similar problem before? If so, please let me know. Any suggestions are welcome.
    thx

    Post Author: ole
    CA Forum: .NET
    Continuous paper is a little bit longer than normal A4 paper. I found only one way to set it: ReportDocument.PrintOptions.PaperSize =CrystalDecisions.Shared.PaperSize.PaperFanfoldStdGermanI had no success, setting continuous papersize by printer setup.  ... waiting for CustomPaperSize-Property (like CustomPaperSource)... Olaf 

  • Prinitng issue with CS5 and Epson pro3800 printer

    CS5 will not hold printer driver settings after leaving driver setup screen. Eg., after setting ICM and choosing Adobe RGB color space and icc profile from menu, when you click OK, Adobe screen reverts to Photoshop adjusts colors and not printer adjust colors as it should. If you change the setting manually, when you renetr driver setup, it now shows 'no color management and not ICM as it should. This does not occur with CS3 or 4. Any help is appreciated.

    I don't have this problem but i can tell you printing out of CS5 is a mess nothing works the way it should....check out my forum i started... right now i just chucked cs5 and went back to cs3

  • HELP: Trying to print with a dot and matrix printer

    Ok, here's the deal:
    I own a very very old, 1985, OLIVETTI DM 292 printer and I want to try printing with it on Mac OS X 10.5.7 .
    I am trying to use the generic EPSON 9- or 24-pin drivers that are present in OS X.
    But so far I've had very little success.
    I am using a parallel-to-USB cable that makes OS X recognize the printer as the name of the cable manufacturer.
    Let's do an example:
    I want to print a .doc, Microsoft Word document.
    I PRINT and select the DaM printer.
    The status window eventually comes to "GenericClass: waiting for device" and the printer freezes.
    Previously, if I turned the printer off and then on immediately after it would print (even with the most possible chaos).. but this trick seems to be uneffective now.
    Can you help me ?
    Thanks to anyone who'll answer.

    Try the alternate USB driver, usbtb. It is supposed to help with USB-parallel adapter cables.
    http://buymelunch.org/printing/usbtb/

  • SAPSCRIPT problem in printing on Dot Matrix Printer

    Hi!
    I have a SAPSCRIPT Form with page format INCH12. The SAPSCRIPT output is displayed properly in print preview. But when it is sent for printing on the Dot matrix printer the first three lines of the second page are printed on the first page at the bottom. Paper size is also 12INCH. I tried adjusting all the windows and putting blank lines. I also gave /: NEW-PAGE command. But it did not solve the problem.
    I am not able to identify where exactly the problem is? Is it in the SAPSCRIPT or in printer settings.
    If anyone had faced similar problem and was able to solve it then please reply.

    Hi
    if it is possible try to print the same in another printer and confirm the problem
    no doubt certain printers may create such problems while printing the output
    so to confirm the problem try with other printer.
    Reward points for useful Answers
    Regards
    Anji

  • Crystal reports printing in dot matrix printer

    I'm using Crystal Reports 2008 with Visual Basic.Net 2008. The problem is that when i print the report in a laser printer, everything is good, but when i used dot matrix printer (like Epson LX 300+), reports is printed smaller than original, doesn't matter if i see good in preview. This is an Asp.Net web form.
    How can i fix this problem

    1) Make sure you have the latest CR Service Pack:
    SP4 https://smpdl.sap-ag.de/~sapidp/012002523100008782452011E/cr2008sp4.exe
    SP4 MSI https://smpdl.sap-ag.de/~sapidp/012002523100008782532011E/cr2008sp4_redist.zip
    SP4 MSM https://smpdl.sap-ag.de/~sapidp/012002523100008782522011E/cr2008sp4_mm.zip
    2) Make sure you have the latest updates for the printer driver
    3) Make sure the printer driver is Unicode compliant
    4) Experiment with the "No Printer" option and Dissociate Formatting Page Size and Printer Paper Size option
    5) Compare print from the CR designer to the app print. Do you see the same issue with both?
    Ludek
    Follow us on Twitter http://twitter.com/SAPCRNetSup
    Got Enhancement ideas? Try the [SAP Idea Place|https://ideas.sap.com/community/products_and_solutions/crystalreports]

  • Print Document in Matrix printer

    Hi, please helpme
    how document print in matrix printer.?
    the characteristic  are.
    - document type smartforms
    - printer EPSON II
    - size paper is Letter
    - The transaction that I use is S_P00_07000134
    - S.O. is Linux
    Problems now are.
    The printed document shows misaligned information
    That I must realize in order that the impression of the document shows aligned information
    Thanks for you help.
    Carlos Orden
    Edited by: Carlos Orden on Mar 22, 2011 12:11 AM

    Hi,
    Does the alignment look correct in te print preview? There are some problems with dot matrix printers due to limitations of the ESC/P printer lamguage.(see SAP note #19807)
    Try printing via windows and a windows device type like SAPWIN or SWINCF. The result should be better.
    Regards,
    Aidan

  • Labels printed in Dot Matrix Printer

    Hi Experts,
        I am new to the label creation.
    I need to create a new label which will be printed using a Epson Dot matrix printer.
    I got an idea how to do it in zebra printing. But still I am wondering how it can be done for a dot matrix.
    Whether it is same like zebra programming or dot matrix do have some other coding language to display the label?
    Could you please explain me on this?
    Thanks & Regards,
    Arun.

    hi,
    there is a huge difference between a standard dot matrix printer and a zebra printer.
    a zebra printer mworks with ZPL II commands. All other printer works otherwise.
    However. If you use smartforms the code in the smartform is converted to ZPL|| automatically. ( I think you can see it in the spool but i am not sure)
    If you use sapscript you have to code the ZPLII yourself.
    On an other printer you can work with normal commands. You have only to take care that the printer has a porper driver. Ad fthe form has the proper pagelayout.
    This will do.
    Gr., Frank

  • Printing Invoice Dot Matrix Printer  in the paper size 9.5 x 11 inches

    Dear All, 
    Am using Pre-printed Stationery but I have a problem with  printing configuration for AR Invoice through Dot Matrix Printer in paper size 9.5 x 11 inches, when command to print the first page it print perfect but the continuation  is not start on the body of the contents but it start from the header of the pre-printed stationery  any one with experience on this please share with me.
    Regards
    Grayson

    hi,
    Have you customized PLD according to paper size ?
    Check whether you customized fields in start of report area ? If yes then it will be printed
    only on first page.
    Check for printer supported by B1 in below link
    [SAP Business One Best-Practice System Setup and Sizing document ]
    Jeyakanthan

Maybe you are looking for