Urgent help needed in configuring X1151A for RAC cluster

for RAC requirements I have to configure this card to use the interface name of ce1 but I have tried changing slots and puting /etc/hostname.ce1 file out there but it fails .. it always comes up as ce0.
my question is : How can I cofigure this card to come up as ce1 ? in the other box I had to do nothing .. i just placed the /etc/hostname.ce1 file with hostname and it works perfect.
can you please email me a copy of your response at [email protected] ?
thanks
Sami

Look for "ce" instances in the /etc/path_to_inst file. You'll need to change the lines so that the hardware path you want is "1".
Keep a backup and write down the pathname. You can give that path to a 'boot -a' prompt if anything bad happens.
Darren

Similar Messages

Urgent help needed in configuring X1151A

for RAC requirements I have to configure this card to use the interface name of ce1 but I have tried changing slots and puting /etc/hostname.ce1 file out there but it fails .. it always comes up as ce0.
my question is : How can I cofigure this card to come up as ce1 ? in the other box I had to do nothing .. i just placed the /etc/hostname.ce1 file with hostname and it works perfect.
can you please email me a copy of your response at [email protected] ?
thanks
Sami

For the discussion in this forum thread, the path-to-inst file
can be though of as a repository of every device path
for every lump of hardware that was ever installed to a system.
It tells Solaris where to find the devices, along their communication interconnect paths.
Thus a device driver can know where to sends its commands
and where to listen for any return signalling responses from the device.
Issues can arise if a device was successfully installed to a path,
such as when a PCI card is installed to a particular slot,
and that card gets moved to another slot.
The path-to-inst file will "remember" the old path, in case you return the card.
No software structures need to be re-built when it reappears in its old slot position.
The former functionality is maintained if ever needed again.
The new position initiates a new entry into the file,
such as when there are two of the same cards instead of the original solitary card.
For your circumstances, there's got to be something in the computer's configuration
that can isolate the data streaming to IP address #1 ( such as for ce0 )
from whatever data might need to go through the other IP address ( such as for ce1 ).
My suggestion for you is to use the devfsadm command.
Review its man pages.
Decide how you want the computers to be configured -- probably using ce0 on both.
devfsadm -C will purge out stale entries and rebuild the path-to-inst file.
A reconfiguration reboot, such as might result from a boot -r,
only appends new device instances to the file.
There's no cleanup, or 'housekeeping', done to it.

Desperate help needed to configure WVC210 for remote access?

Hi, I'm new and desperately need some help on setting up my WVC210 for remote access.
I manage to setup and see images from my WVC210 using my home LAN via both wired and also wireless.
I have 2 questions:
(a) for wireless connection, i only manage to get connection to my WVC210 if i disable the wireless security from my router. But that means i'm opening my wireless LAN to everyone. How can i still get connection to the camera if i enable the wireless security from my router. (FYI: my router is 2Wire ADSL from Singnet Mio)
(b) how can i get connection to my WVC210 from outside or in my office? I type in the camera Fixed IP address (displayed on the front screen) on the web browser, by it shows a error page. Is there some setting that i might need to adjust ?
Pls kindly help me
Thank you.

Bernard,
For Item (2) is there any difference between the camera built-in dyndns updater versus the software updater? I am under the impression that the software updater is easier to manage.
The biggest difference for you is that the camera always stays at the same location, and the laptop goes with you. Every time you access the internet from a different location with the laptop the software updater is sending the new IP address to dyndns.com. This causes you to lose access to your camera because the FQDN doesn't point to your home IP address anymore. Once the dyndns credentials are in the camera (or router) there is no management needed. The device will automatically update dyndns.com with your new IP address as it changes, and you do not need to do anything.
For Item (3), are you saying port forward 1025 is it for the 2nd camera only or for both? Or is it 2nd camera use 1025 and first camera use 8080?
Here's an example of what I mean:
Camera 1: 192.168.1.210 port 1024. In router, forward port 1024 to 192.168.1.210
Local Access: http://192.168.1.210:1024
Remote Access: http://bernards210.dyndns.org:1024 (Example)
Camera 2: 192.168.1.211 port 1025. In router, forward port 1025 to 192.168.1.211
Local Access: http://192.168.1.211:1025
Remote Access: http://bernards210.dyndns.org:1025 (Example)
Camera 3: 192.168.1.212 port 1026. In router, forward port 1026 to 192.168.1.212
Local Access: http://192.168.1.212:1026
Remote Access: http://bernards210.dyndns.org:1026 (Example)
to access the 2 camera outside, do i have to have another dyndns host name or can i use the current one for both camera?
As you can see in the above example, the dyndns name remains the same for remote access to all three cameras. The only change is the port number at the end. Your router will translate the port number to the IP address that the port is forwarded to, allowing you to select the camera that you wish to view by changing the port number in the address.
I was actually thinking that the camera web browser can show 2 camera at the same time. Is it possible?
No. Each browser window will display a single camera. You can however opens multiple instances of your browser to allow viewing of more than one camera simultaneously. A better solution is to install the Video Monitoring Software that is included with the camera which allows you to view multiple cameras in the same window.

Urgent help need on configuring MPLS TE

i found that CSPF is not finding other path still there is no bandwith on SPF path and tunnel1 remain down if i down second tunne2 then tunnel 1 comes up not try to use other interfaces which r free with enough bandwidth. all router have MPLS TE and RSVP.
please read all in detail below
my freinds i have one Q. for MPLS TE. i m using 3660 router for MPLS TE on dayanagen simulater. in this lab there is 5 routers with 512 kbp RSVP on each interface all router with MPLS TE. configure are as->
R1 /0 ---R2 /0
R2 ==== R3 have Two interfaces s1/1 and s1/3
R2 /2-----R5 /2 interface connection
R3 ---- R5 int connection
R3 ---- R4 tunnel to R4 from R1,R2 with 300kb each
tunnel1 on R1 to R4 with 300kb rsvp TE
tunnel2 on R1 to R3 with 50kb rsvp TE
tunnel1 on R2 to R4 with 300kb rsvp TE
diagram like that below (ignore ..dots)
R1---R2=====R3----R4
.......I_______I
..........R5
i created tunnels from R1----> R4 with 300Kb.
second R1---->R5 with 50Kbp tunnel
and
on R2---->R4 tunnel with 300kbp.
PROBLEM IS when R1 tunnel go via R2 to R4 it takes s1/1 interface with 300rsvp. means for R2 tunnel should find next interface for same destination R4 becaused there is not enough space.On one of remaining on interfaces on R2 s1/3 or S1/2 but R2-->R4 tunnel remain down. when i down R1---R4 tunnel R2--R4 tunnel comes up on same interface. NOW when i up R2 tunnel first and later R1. then same thing again R1 down and wait for R2 tunnel to go down.then up on same interface. if u see there is still two path r free to go R4 on R2
1. R2 s1/3 ----> s1/3 of R3
2. R2 s1/2 ---->s1/2 of R5 with both 512 kb RSVP
there is using R2 s1/1 for tunnel
why not with help of CSPF it takes other path when 512 link is also free on R2 router to same destination??? its on dyanamips is it can problem with simulater.
it means that on R2 using SPF path for R4 for both tunnel and not trying to find other CSPF path thats why my two interfaces are free with 512kbp RSVP on same router R2. why not CSPF using other remaining path. and down one of tunnel because of there is no space on tht s1/1 interface........
PLZZ ANSER ME I NEVA USE MPLS TE B4
thanks in advance!

sorry m8 for late reply i had sort the problem. it occur because i was using 4 router now when i used TE with 12 router on daynagen it is working fine.
Question
now i have one question. i am trying to use TE with MPLS VPN site to site. as you know site to site MPLS VPN send traffic both way from R1 to R2 and R2 to R1.
but if i create MPLS TE tunnel1 on R1 to destination R2 then all traffic from R1 will go via tunnel1. but traffic from R2 wil go to R1 via normal route becasue tunnels is one way onli can see on R1
that means i have to create tunnels at both end in opposite directions. please reply me.
MPLS VPN site to site between R1 --- R2 have to create tunnels for both direction because tunnel work in on way?
R1 ---->R2 tunnel1
R1<-----R2 tunnel2
thanks

Urgent help needed while applying patch for upgrade with conflicts

I try to upgrade 11.2.0.2 to 11.2.0.3 on LInux environment.
I have to apply patch P1253900 before the upgrade per oracle doc.
however I got following conflict:
Verifying environment and performing prerequisite checks...
Checking skip_duplicate
Checking skip_subset
Conflicts/Supersets for each patch are:
Patch : 12539000
Conflict with 12827726
Conflict details:
/u01/app/grid/product/11.2.0/grid/lib/libserver11.a:/ksxp.o
Following patches have conflicts: [ 12827726 12539000 ]
Refer to My Oracle Support Note 1299688.1 for instructions on resolving patch conflicts.
I checked above oracle note, and did not say any resolution.
If anybody had the same issue before, please help me with the resolution.
Thanks in advance.

Follow the steps in this MOS Doc
Database Patch conflict resolution [ID 1321267.1]
This MOS Doc is referenced in 1299688.1
HTH
Srini

Urgent Help Needed: UME action missing for permission option

Hi Gurus,
I have created a role and i want the users in that role will have the access to edit Permissons under the Sys Admin tab. When I right click on Portal content under permission i could only see Refresh, I want the option permission when rt click here, I can see this option when i use Superadmin role. Can anyone please suggest wat action is required.
Thanks,
Rams
Message was edited by:
admin ram
Message was edited by:
admin ram

Hi Ram
Please check assigning these roles instead of super admin role
"content_admin_role" or " contentmanager" . In case if any of these enable open permissions then check out what activity is in the role and include in yours .
Regards
Rahul
Award points if help useful "

User Exit for Material Group...Urgent help needed

Does anybody have an idea of which user exit can be used to capture the changes made to material group in MM02(Material)..... Urgent help needed...

See the below user exit and this will trigger under MM01,MM02 and MM17 Transaction
Enhancement name : MGA00001
Function module :EXIT_SAPLMGMU_001
Include : ZXMG0U02
Reward Points if it is helpful.
Thanks
Seshu

Wlan Security Issue urgent help needed

Dear Community,
i have a wlc 5500 with two ssids for employees and contractors
both ssids with layer2 security WPA+WPA2 and auth key mgmt 802.1x are authenticated with ACS 5.0 (active directory) for users access and are working fine after windows adapter setting
but my question is, can i do some thing like
authentication with acs 5.0 (active directory) for users access but without windows adapter seting????
i mean without changing any setting on windows adapter ( leave it as default).
if i can then how i can???
or i cann't do that i mean there is not any option to do that?
plz give me your seggustions i need urgent help on this topic.

thanks for your reply George
it seems only for 802.1x authentication key methode needs windows adaptor changing as per you.
is there any other option to configure wlan scurity with acs (MS active Dir) user authentication like
let me tell you something
i want when any client will try to connect any wlan he ll just prompted to use his username and password(of active directory) without doing any changes in window adapter setting???
i don't care layer 2 security will be whatever like wpa+wpa2 with 802.1x OR something else
can i do that or no ??
if yes i can than what type of security?
please don't tell me about webauthentication i already know about that and i ll use that mothed for GUSET-Wlan.
kindly reply me soon
Thanks

URGENT HELP NEEDED ... Tomcat Realm and JRE1.4 plug-in problem

I have tried the Security Realm of Tomcat. Since I do not have
an LDAP server, I decided to use the Tomcat-users.xml file in
Tomcat\conf directory.
I added the following lines of code in the web.xml file.
<security-constraint>
<web-resource-collection>
<web-resource-name>Entire Application</web-resource-name>
<url-pattern>/*</url-pattern>
</web-resource-collection>
<auth-constraint>

<role-name>webviewer</role-name>
</auth-constraint>
</security-constraint>
<login-config>
<auth-method>BASIC</auth-method>
<realm-name>Tomcat Manager Application</realm-name>
</login-config>
The <role-name> "webviewer" is added into "Tomcat-Users.xml" as the following:
<tomcat-users>
<user name="test" password="password" roles="webviewer" />
</tomcat-users>
So, now when we type the url: http://localhost:8080/adbpdbre/default.htm, TOMCAT shows a dialog box asking for UserName: and Password:Now, only when we give the username and password, it shows the page. This is exactly what we want.
But the problem now is, this default.htm page, has 5 links to 5 applets. The first time that I click on one of these links, the JRE plug of 1.4 shows a dialog again asking for the username and password. Till I dont provide the username and password the system doesnt go ahead and applet doesnt load. I do not want the JRE to ask me for the username/passwords again..How to avoid this ?
Can you give me some more information on this. Ultimately in the production usage, we will be using LDAP and not Tomcat's memory realm.
URGENT HELP NEEDED ... I need to get back to my client on this.
Help would be v. much appreciated.

In the config file, you 're essentially saying that you want Tomcat to prompt for usr/passw on every request (url-pattern = /*) made by a 'webviewer', and that's exactly what Tomcat is doing.
Consider using specific url-patterns & roles for resources to be protected. If for now, all you need is to protect the first page, use a more specific url-pattern.
Just an advice : if you'll be using LDAP in production, do not waste time with Tomcat's Security Realm and the BASIC authentication type, since the two have not much in common. Start reading doc on LDAP, and code a prototype, or even better, a vertical slice of the app (i.e a proof of concept).

URGENT HELP NEEDED - iPhone 3Gs no longer detected or charged by MacBook

My iPhone 3Gs (3.1) has been running fine, until several hours ago today, when I plugged it to my MacBook, the iPhone is no longer detected - it doesn't show up in iTunes, nor it is charged. I tried opening iPhoto, and it wasn't there too. Not with Image Capture too. I tried charging it using the out-of-box wall charger using the same out-of-box USB cable I use for MacBook, and it can be charged without any problem. Then I put it into Recovery mode, and there iTunes can see it. I don't want to restore it before I figure out exactly what went wrong, as I don't want the restore process somehow gets stuck in the middle that the connection is lost again.
I've tried reinstalled iTunes, including completely removal of Apple Mobile Device Support, as instructed by Apple. But still no luck.
I've tried switching to another USB port of my MacBook. No luck.
My iTunes is the latest 9.0.1, and my Mac OSX is 10.6.1. My iPhone is on 3.1, upgraded from 3.0.
I've read from web that it seems I'm not the only one out there having this problem. But none of them seem having any real working solution.
Urgent help needed & appreciated. Millions of thanks in advance.
Gary

1. I used both cables - theirs & mine ... and on several macs
2. yes, same cable for wall & mac
3. as said, i did completely remove & install itunes (incl. apple mobile device support), as instructed on the apple webpage
anyway, did a restore just now. it seems okay now. but the problem is i have no idea what cause this, and i can't replicate the problem. so i don't know when it will happen again ... maybe a bug with os 3.1 ... others on web said os 3.1 is quite buggy ...

Urgent help needed, can I restore N900 Backup file...

i owned a N900 (now sold out)
before selling i took backup of contacts from backup restore option in application section
now i bought a N8 but i m not able to restore my contacts
1. is there any way to restore them in N8?
2. if not, can i convert them in TEXT or any readable format
urgent help needed
thanks in advance

The backup procedures built into the phone are only designed for restoring to the same phone (ie: in case or data corruption, software update or repair etc.), they can't usually be used to restore to a phone with a different operating system.
You should have backed up with Ovi Suite before selling the N900, that would have been able to restore to the N8.

Urgent help needed - new to Macs, accidently cut and paste over top of photo folder and now no sign of folder or file, no auto back-up in place, how can I restore photos pls

Urgent help needed - new to Macs, accidently cut and paste over top of photo folder and now no sign of folder or file, no auto back-up in place, how can I restore photos pls

Thanks for prompt reply, yes we have tried that but have now closed down the browser we where the photos were.
We haven't sent up time machine, do you know whether there is any roll-back function on a Mac?
Thanks

Urgent help needed with un-removable junk mail that froze Mail!!

Urgent help needed with un-removable junk mail that froze Mail?
I had 7 junk mails come in this morning, 5 went straight to junk and 2 more I junked.
When I clicked on the Junk folder to empty it, it froze Mail and I can't click on anything, I had to force quit Mail and re-open it. When it re-opens the Junk folder is selected and it is froze, I can't do anything.
I repaired permissions, it did nothing.
I re-booted my computer, on opening Mail the In folder was selected, when I selected Junk, again, it locks up Mail and I can't select them to delete them?
Anyone know how I can delete these Junk mails from my Junk folder without having to open Mail to do it as it would appear this will be the only solution to the problem.

Hi Nigel
If you hold the Shift key when opening the mail app, it will start up without any folders selected & no emails showing. Hopefully this will enable you to start Mail ok.
Then from the Mail menus - choose Mailbox-Erase Junk Mail . The problem mail should now be in the trash. If there's nothing you want to retain from the Trash, you should now choose Mailbox- Erase Deleted Messages....
If you need to double-check the Trash for anything you might want to retain, then view the Trash folder first, before using Erase Junk Mail & move anything you wish to keep to another folder.
The shift key starts Mail in a sort of Safe mode.

IPhone 3G 8GB Crashes when syncing with iTunes. URGENT HELP NEEDED.

I have latest iTunes and OS on my iPhone 3G...
Every time i plug my iPhone in it begins to sync and then iTunes will freeze and not respond..
I have tried re installing iTunes.. I can't reset my iPhone as i can't create a backup..
URGENT HELP NEEDED PLEASE!

I don't have an iphone, but if it's anything like my click-wheel ipod, a reset doesn't delete anything.
It just resets the ipod's operating system, kind of like a PC restart. Did you try this Sleep/Wake button thing mentioned here?
http://support.apple.com/kb/HT1737
Maybe it's a podcast of voice memo causing the problem like it did for this person
http://discussions.apple.com/message.jspa?messageID=10907809#10907809
That's all I got. You might have better luck on an iPhone forum. Everyone there would probably have one. Like I said, I don't.

IPhone 4 reset itself, photos lost -URGENT HELP NEEDED

Hi there,
Urgent help needed!!
Tonight I was taking extremely important photos throughout an event on my iPhone 4, however, my iPhone 4 ran out of battery once I was near a charger I plugged it in and for some reason my iPhone had reset itself. Back up icloud options were from yesterday, but the photos that I was taking at the event are needed urgently. Is there any way possible I can recover the photos that were taken?
Thanks in advance!!!!

Slymm71 wrote:
just had similar problem got email from find my phone saying initiating full phone wipe this cannot be stopped ***? i own the phone from new and registerred in m name but wiped whilst i was using it !!!
See your other post...
https://discussions.apple.com/message/18876037#18876037

Urgent help needed in configuring X1151A for RAC cluster

Similar Messages

Maybe you are looking for