Urgent Help : Workflow Problem

Hi,
Siebel 8.0
I am working on EAI workflows. I am using Siebel Tools Simulator and also the Business Service Simulator to test my workflows. However I am facing some issues.
I am not able to simulate my new workflows. However all the older workflows are working fine. Below are the steps that I take to simulate the workflows:
1. Create a workflow in Siebel tools and click the publish/activate button. Check if its status changed to Completed.
2. Open Siebel Web Client > Sitemap > Admin-Business Service > Simulator.
3. Process Name "Workflow Process Manager" and Method name "RunProcess"
4. Under Input Arguments: Property Name "ProcessName" and Property Value "WORKFLOW NAME"
5. Click the run button.
At this point I get error as:
Siebel
Cannot execute workflow process definition 'Test EAI Workflow 4'.(SBL-BPR-00158)
OK
However the older workflows work fine with the same approach. I am able to Simulate. Even I copied the existing workflows (that I am able to Simulate) but they dont work either. :(
Please Help
Thanks :)

Hi,
You need to activate the new workflows u have created. If u want to test the workflow in thin client, then manually import the workflow in active workflow process and try to simulate.
This error will occur if the workflow is not "ACTIVE" in the active workflow process under Administration - Business Process.
Regards,
Joseph
Edited by: Joseph ArulDass on Jul 14, 2010 3:47 PM
Edited by: Joseph ArulDass on Jul 14, 2010 3:56 PM

Similar Messages

Urgent HELP needed: Problems transfer from Bold 9900 to Z10

Dear helpdesk,
I've just received my new Z10 and want to transfer all data from my old 9900.
Using Link software seems to work fine.... until the copying from the 9900 is almost finished. Then I get the message "Data could not be copied from your device due to the following errors: There could have been a problem with the device or communication during the backup. Verify that the device is tuned on and connected".
Surely that IS the case.... I've already removed the old BB Desktop SW and reinstalled the Link SW.
Without success unfortunately.
What do I do wrong/do I need to do to get my files copied to the Z10?
I am also wondering what would happen to the memos which I made using the 9900's MemoPad?
Thanks for your swift help!
Marnix Kerkhoff

Hello MarnixKerkhoff,
Welcome to the BlackBerry Support Forums.
Reinstall BlackBerry Desktop Software and try to backup the data from your BlackBerry® Bold™ 9900 smartphone. Does the data backup successfully?
The BlackBerry MemoPad data will be transferred to the Remember application on the BlackBerry® Z10 smartphone.
Please let us know how you make out.
-RoundBrown
Come follow your BlackBerry Technical Team on Twitter! @BlackBerryHelp
Be sure to click Like! for those who have helped you.
Click Accept as Solution for posts that have solved your issue(s)!

Urgent help : printjob() problem

hi,
when i used printjob class for printing pages. in print
option window print range selection is disabled. that means i am
not able to print specific pages. for example 2-5 pages.
i am using following code for printing. it's printing all the
pages.
var my_pj = new PrintJob();
if (my_pj.start()) {
for (var i = 0; i<_root.iPages; i++) {
var x = MainPrint["prints"+i]._xscale;
var y = MainPrint["prints"+i]._yscale;
MainPrint["prints"+i]._xscale = 86;
MainPrint["prints"+i]._yscale = 92;
my_pj.addPage(MainPrint["prints"+i], {xMin:0, xMax:860,
yMin:0, yMax:810});
MainPrint["prints"+i]._xscale = x;
MainPrint["prints"+i]._yscale = y;
my_pj.send();
delete my_pj;

Hi,
You need to activate the new workflows u have created. If u want to test the workflow in thin client, then manually import the workflow in active workflow process and try to simulate.
This error will occur if the workflow is not "ACTIVE" in the active workflow process under Administration - Business Process.
Regards,
Joseph
Edited by: Joseph ArulDass on Jul 14, 2010 3:47 PM
Edited by: Joseph ArulDass on Jul 14, 2010 3:56 PM

Urgent Help Installation Problems (It's getting annoying now... been over a year)

When ever i try to install apple snow leopard a message error appears "please clean disc" or "unsupported files"

Clean the bottom of your installer disk or get a new one from Apple.
If the problem continues, you have a dirty lense in your Superdrive most likely.

URGENT HELP NEEDED ... Tomcat Realm and JRE1.4 plug-in problem

I have tried the Security Realm of Tomcat. Since I do not have
an LDAP server, I decided to use the Tomcat-users.xml file in
Tomcat\conf directory.
I added the following lines of code in the web.xml file.
<security-constraint>
<web-resource-collection>
<web-resource-name>Entire Application</web-resource-name>
<url-pattern>/*</url-pattern>
</web-resource-collection>
<auth-constraint>

<role-name>webviewer</role-name>
</auth-constraint>
</security-constraint>
<login-config>
<auth-method>BASIC</auth-method>
<realm-name>Tomcat Manager Application</realm-name>
</login-config>
The <role-name> "webviewer" is added into "Tomcat-Users.xml" as the following:
<tomcat-users>
<user name="test" password="password" roles="webviewer" />
</tomcat-users>
So, now when we type the url: http://localhost:8080/adbpdbre/default.htm, TOMCAT shows a dialog box asking for UserName: and Password:Now, only when we give the username and password, it shows the page. This is exactly what we want.
But the problem now is, this default.htm page, has 5 links to 5 applets. The first time that I click on one of these links, the JRE plug of 1.4 shows a dialog again asking for the username and password. Till I dont provide the username and password the system doesnt go ahead and applet doesnt load. I do not want the JRE to ask me for the username/passwords again..How to avoid this ?
Can you give me some more information on this. Ultimately in the production usage, we will be using LDAP and not Tomcat's memory realm.
URGENT HELP NEEDED ... I need to get back to my client on this.
Help would be v. much appreciated.

In the config file, you 're essentially saying that you want Tomcat to prompt for usr/passw on every request (url-pattern = /*) made by a 'webviewer', and that's exactly what Tomcat is doing.
Consider using specific url-patterns & roles for resources to be protected. If for now, all you need is to protect the first page, use a more specific url-pattern.
Just an advice : if you'll be using LDAP in production, do not waste time with Tomcat's Security Realm and the BASIC authentication type, since the two have not much in common. Start reading doc on LDAP, and code a prototype, or even better, a vertical slice of the app (i.e a proof of concept).

Urgent help need on swing problem

Dear friends,
I met a problem and need urgent help from guru here, I am Swing newbie,
I have following code and hope to draw lines between any two components at RUN-TIME, not at design time
Please throw some skeleton code, Thanks so much!!
code:
package com.swing.test;
import java.awt.*;
import java.awt.event.*;
import java.awt.geom.*;
import javax.swing.*;
import javax.swing.event.*;
public class LongguConnectLineCommponent
    public static void main(String[] args)
        JFrame f = new JFrame("Connecting Lines");
        f.setDefaultCloseOperation(JFrame.EXIT_ON_CLOSE);
        f.getContentPane().add(new ConnectionPanel());
        f.setSize(400,300);
        f.setLocation(200,200);
        f.setVisible(true);
class ConnectionPanel extends JPanel
    JLabel label1, label2, label3, label4;
    JLabel[] labels;
    JLabel selectedLabel;
    int cx, cy;
    public ConnectionPanel()
        setLayout(null);
        addLabels();
        label1.setBounds( 25, 50, 125, 25);
        label2.setBounds(225, 50, 125, 25);
        label3.setBounds( 25, 175, 125, 25);
        label4.setBounds(225, 175, 125, 25);
        determineCenterOfComponents();
        ComponentMover mover = new ComponentMover();
        addMouseListener(mover);
        addMouseMotionListener(mover);
    public void paintComponent(Graphics g)
        super.paintComponent(g);
        Graphics2D g2 = (Graphics2D)g;
        g2.setRenderingHint(RenderingHints.KEY_ANTIALIASING,
                            RenderingHints.VALUE_ANTIALIAS_ON);
        Point[] p;
        for(int i = 0; i < labels.length; i++)
            for(int j = i + 1; j < labels.length; j++)
                p = getEndPoints(labels, labels[j]);
//g2.draw(new Line2D.Double(p[0], p[1]));
private Point[] getEndPoints(Component c1, Component c2)
Point
p1 = new Point(),
p2 = new Point();
Rectangle
r1 = c1.getBounds(),
r2 = c2.getBounds();
int direction = r1.outcode(r2.x, r2.y);
switch(direction) // r2 located < direction > of r1
case (Rectangle.OUT_LEFT): // West
p1.x = r1.x;
p1.y = r1.y;
p2.x = r2.x + r2.width;
p2.y = r2.y;
if(r1.y > cy)
p1.y = r1.y + r1.height;
p2.y = r2.y + r2.height;
break;
case (Rectangle.OUT_TOP): // North
p1.x = r1.x;
p1.y = r1.y;
p2.x = r2.x;
p2.y = r2.y + r2.height;
if(r1.x > cx && r2.x > cx)
p1.x = r1.x + r1.width;
p2.x = r2.x + r2.width;
break;
case (Rectangle.OUT_LEFT + Rectangle.OUT_TOP): // NW
p1.x = r1.x;
p1.y = r1.y;
p2.x = r2.x + r2.width;
p2.y = r2.y;
if(r1.y > r2.y + r2.height)
p2.y = r2.y + r2.height;
break;
case (Rectangle.OUT_RIGHT): // East
p1.x = r1.x + r1.width;
p1.y = r1.y;
p2.x = r2.x;
p2.y = r2.y;
if(r1.y > cy)
p1.y = r1.y + r1.height;
p2.y = r2.y + r2.height;
break;
case (Rectangle.OUT_TOP + Rectangle.OUT_RIGHT): // NE
p1.x = r1.x + r1.width;
p1.y = r1.y;
p2.x = r2.x;
p2.y = r2.y;
if(r1.y > cy)
p1.y = r1.y + r1.height;
p2.y = r2.y + r2.height;
if(r1.y > r2.y + r2.height)
p1.y = r1.y;
else
if(r1.y > r2.y + r2.height)
p2.y = r2.y + r2.height;
break;
case (Rectangle.OUT_BOTTOM): // South
p1.x = r1.x;
p1.y = r1.y + r1.height;
p2.x = r2.x;
p2.y = r2.y;
if(r1.x > cx && r2.x > cx)
p1.x = r1.x + r1.width;
p2.x = r2.x + r2.width;
break;
case (Rectangle.OUT_RIGHT + Rectangle.OUT_BOTTOM): // SE
p1.x = r1.x + r1.width;
p1.y = r1.y + r1.height;
p2.x = r2.x;
p2.y = r2.y;
break;
case (Rectangle.OUT_BOTTOM + Rectangle.OUT_LEFT): // SW
p1.x = r1.x;
p1.y = r1.y + r1.height;
p2.x = r2.x;
p2.y = r2.y;
if(r1.x > r2.x + r2.width)
p2.x = r2.x + r2.width;
if(r1.x > cx && r2.x > cx)
p1.x = r1.x + r1.width;
p2.x = r2.x + r2.width;
return new Point[] {p1, p2};
private void determineCenterOfComponents()
int
xMin = Integer.MAX_VALUE,
yMin = Integer.MAX_VALUE,
xMax = 0,
yMax = 0;
for(int i = 0; i < labels.length; i++)
Rectangle r = labels[i].getBounds();
if(r.x < xMin)
xMin = r.x;
if(r.y < yMin)
yMin = r.y;
if(r.x + r.width > xMax)
xMax = r.x + r.width;
if(r.y + r.height > yMax)
yMax = r.y + r.height;
cx = xMin + (xMax - xMin)/2;
cy = yMin + (yMax - yMin)/2;
private class ComponentMover extends MouseInputAdapter
Point offsetP = new Point();
boolean dragging;
public void mousePressed(MouseEvent e)
Point p = e.getPoint();
for(int i = 0; i < labels.length; i++)
Rectangle r = labels[i].getBounds();
if(r.contains(p))
selectedLabel = labels[i];
offsetP.x = p.x - r.x;
offsetP.y = p.y - r.y;
dragging = true;
break;
public void mouseReleased(MouseEvent e)
dragging = false;
public void mouseDragged(MouseEvent e)
if(dragging)
Rectangle r = selectedLabel.getBounds();
r.x = e.getX() - offsetP.x;
r.y = e.getY() - offsetP.y;
selectedLabel.setBounds(r.x, r.y, r.width, r.height);
determineCenterOfComponents();
repaint();
private void addLabels()
label1 = new JLabel("Label 1");
label2 = new JLabel("Label 2");
label3 = new JLabel("Label 3");
label4 = new JLabel("Label 4");
labels = new JLabel[] {
label1, label2, label3, label4
for(int i = 0; i < labels.length; i++)
labels[i].setHorizontalAlignment(SwingConstants.CENTER);
labels[i].setBorder(BorderFactory.createEtchedBorder());
add(labels[i]);

If you need some help, be respectful of the forum rules and people will help. By using "urgent" in the title and bumping your message every 2 hours you're just asking to be ignored (which is what you ended up with).

Urgent Help Reqd: Delta Problem....!!!

Hi Experts,
Urgent help reqd regarding follwoing scenario:
I am getting delta to ODS 1 (infosource : 2LIS_12_VCHDR) from R/3. Now this ODS1 gives delta to Cube1. I got one error record which fails when going to cube (due to master data check).And this record would be edited later.
So I thought of re loading cube and using error handling to split request in PSA and load valid records in cube.Later when I have coorect info abt error, I would load erroneous record manually using PSA.
I did following steps:
1)Failed request is not in cube...(setting is PSA and then into target)....also it has been deleted from PSA.
2)Remove data status from source ODS1.
3)Change error handling in infopackage to valid " Valid records update, reporting possible".
4)start loading of cube.
But when I did this I got following message :
<b> "Last delta update is not yet completed.Therefore, no new delta update is possible.You can start the request again if the last delta request is red or green in the monitor"</b>
But both my requests in cube and ODS are Green...no request is in yellow...!!
Now the problem is :
1) I have lost ODS data mart status
2)how to load valid records to cube, since errorneous record can be edited only after 3- 4 days.
3)How not to affect delta load of tomorrow.
Please guide and help me in this.
Thanks in advance and rest assured I will award points to say thanks to SDNers..
Regards,
Sorabh
Message was edited by: sorabh arora

Hi Joseph,
Thanks for replying....
I apolgize and I have modified the message above..
I just checked in cube...there is no failed request for today...and neither in PSA....Person who has handed this to me may have deleted this is PSA..and why req is not in failed state in cube...I am not sure..though setting is "PSA and then into data package".....
So how to go frm here....
Thanks
Sorabh

Need Urgent Help in PM8M-V H problem - keyboard freeze

Hi everyone,
I'm a newbie in this forum and I really need urgent help with my motherboard.
My PC specification:
Intel Pentium 4 2.4GHz
MSI PM8M-V H W7104VMS v3.4 022206 14:32:17
1GB(512MB x 2) Kingston PC3200 400MHz
Seagate SATA II 320GB ST3320620SV (set with jumper to support SATA I)
Power Color ATI Radeon 9550 256MB
Lite-On DVDRW SHM-165P6S
USB mouse, PS/2 Keyboard
I really appreciate if anyone can help to guide me in solving my problem. My keyboard tends to freeze at the part where it says "Press any key to boot from CD". This limits me to do anything until I'm totally loaded into Windows. Thus, disable me to perform any formating and fresh installation of OS. However, the keyboards works fine at the begining of the POST and in BIOS. Is there any settings in BIOS that i should perform?.....
However, I realise in order to get through the foresaid message without the the keyboard freeze up is by keep on trying to boot up and shut down until it works (but only work once, then hv to try again), but this is not a solution as if what if I wanted to have 2 OS?... I cant use the keyboard to choose either of the OS installed. I have tried to change the RAM, change keyboard, use the build in VGA, or even remove the motherboard from the ATX casing - result: still have the same problem. What should I do??.. I have look around the forum for answers but there isnt any (I hope I didnt miss any). Is there any problem with my motherboard, or its BIOS, or any of the harware compatibility or etc..... what actually can I do?
I do not dare to perform any BIOS update Unnecessary (it seems that many have problems with BIOS problem in this forum) and moreover i think my BIOS is the most up-to-date. I cant find any new version in the net. Anyway I will check this topic frequently as possible to hope for any solution. What is the best solutions?
Thanks.

But the thing that makes me wonder is, my BIOS version is the latest but why this type of problem occurs??
What version of BIOS should I use?? Any recommendation ??
Thanks.

Need urgent help. I have been trying to resolve this problem to no avail. I am able to preview my sp

Need urgent help. I have been trying to resolve this problem to no avail. I am able to preview my sprymenu on my local browsers opera, google crome, and IE but when it is uploaded, the sprymenu squashes to the left hand side.

Please get your checkbook ready. (Only kidding.)
Have you ever done a hard factory reset of your Airport Express base? If not, then try it. Push down the reset button with a pen, then keep it depressed as you plug AX into the wall and keep holding it down until the green light blinks 4 times and then turns amber. Then let go. Unplug your broadband modem for a couple of minutes and shut down your Mac. First restart the modem, then the Mac. Use Airport Setup Assistant to set up a new network from scratch.
In System Prefs > Network > Show > Network Port Configurations drop n drag Airport to the top of the list and deselect all port configurations that you do not use.
That's a start.

Problem uninstalling MaxMSPRuntime on mac - urgent help needed

Hello there,
I've been using Cycle 74's MaxMSP Runtime version 5.1 for a while but recently had to witch to an earlier version to make some hardware function along side the Max runtime environment. The problem is that where i would usually just drag and drop Max 5.1 into the trash to uninstall it, for some reason, after i have done this and try to install the older version of Max, OSX wont let me install Max 4.0.8 as it says an updated version is currently installed. I have scoured my hard drive for the remanence of Max 5.1. and deleted everything i've found. Is there a way of overriding macosx and getting it to replace Max5.1 with an older version?
Urgent help needed as i am playing a show this weekend and currently am not able to get my equipment to function.
A shiny nickel for the one who saves my ***.
Thanks
Henry

Hi- Try this...
If you can, reinstall or use time machine to recover your recently deleted MaxMSP Runtime 5.1.
Then, download AppZapper. It is a utility that helps you cleanly delete programs off your mac. It is free for the first 5 uses.
http://appzapper.com/
Then, install AppZapper, and then go ahead and drag the MaxMSP Runtime 5.1 into it, and it should hopefully get rid of the pesky program

URGENT HELP NEEDED (Bios Settings Failed)

Hey Guys,
I am having problems with my MSI Board, and don't know what to do. I am very much a noob to BIOS/and modding so I apologize in advance. You guys helped me a few months ago getting everything up and running and all was great for months. Then last night I walked away from my PC for a while and when i came back a starting screen was on saying my OC Settings Failed to load, i tried other versions I saved and they all failed as well. I ended up loading failsafe options, and got the "double start" where the computer turns on, then instantly shuts off, then turns on again. This allowed me to load windows 7, which then started to "install updates". So i think while i was away Windows automatically updated and rebooted... but would that effect my BIOS settings?
As I said, I had my system running perfect for months no errors or crashes at all based on the Bios setting you guys help me with in this thread: https://forum-en.msi.com/index.php?topic=147854.0
However, last week I removed the heat sink and installed this cooler: http://www.newegg.com/Product/Product.aspx?Item=N82E16835181010&nm_mc=OTC-Froogle&cm_mmc=OTC-Froogle-_-Water+Cooling-_-Corsair-_-35181010
All I did was unhook everything from the MB, install the cooler, and then hook everything back up to the MB. The only thing I may have done wrong is not connect the SATA devices (my HDs and ROMS) back in the spots they were in originally. However after I installed the cooler, they system booted right up, and I haven’t had any problems with my system for the past two weeks. I also should note I didnt make any BIOS changes either after I installed the cooler. So I don’t know if I should have done something there. Yet, like I said the system has been fine for the past two weeks, no crashes or errors... it wasn’t until last night after Windows auto updated that this has begun.
The reason I need "URGENT HELP" is because of course I just a new job with deadlines due and so much video editing work I need to do. I would be fine leaving it on failsafe settings, and forgetting the OC setting all together if I new that would make the system stable. But considering its still doing the "double start" even in failsafe mode, im afraid if i start working my system will crash.
So I am begging anybody for any advice or help they could provide. I will provide my system info below. If anybody can guide me as to what settings I should set in BIOS i would appreciate it. Or perhaps there’s a BIOS update that I should use now that I have a cooler and not a heat sink? If you need any more information from me, just ask. I will be monitoring this thread all day, as I desperately need help.
MY SYSTEM:
Intel 980X chip running Win 7 64bit (with MSI BigBang xPower MB installed in my old Dell XPS 730X)
(1) SATA II WD 3gb Hard Drive @ 1.5TB
(2) OCZ SATA II SSD drives @120GB: http://www.newegg.com/Product/Product.aspx?Item=N82E16820227543
(2) Hitachi 6gb SATA III drives @2TB: http://www.newegg.com/Product/Product.aspx?Item=N82E16822145473
3 DVD/CD/BLUERAY DRIVES:
1 SATA DVD DRIVE
1 SATA BlueRay Drive
1 SATA CD Drive
(So 8 SATA Devices Total)
24GIGs of this ram: http://www.newegg.com/Product/Product.aspx?Item=N82E16820145321
1 NVida Geforce GTX 470
1 Soundblaster X-Fi Titanum Card
New Addition Water Cooler: http://www.newegg.com/Product/Product.aspx?Item=N82E16835181010&nm_mc=OTC-Froogle&cm_mmc=OTC-Froogle-_-Water+Cooling-_-Corsair-_-35181010

PROBLEM: My OC BIOS setting wont load. Even on failsafe i get the "double start". I want to get back to my OC (stable) settings.
UPDATE: Since I posted somebody messaged me mentioned I should have "reset the CMOS" after I installed the new cooler. So I did that, and now they system starts fine without the "double start". I am able to load one of my saved OC settings now as well (but any others causes a failure).
NEW QUESTIONS:
1. Since I reset the CMOS and now the system is starting fine on my last OC settings, is it safe to assume the sytem is stable for now?
2. I never made any power changes or BIOS changes after I installed the new cooler. Should I have?
3. After I reset the CMOS was I soupposed to reinstall the drivers from the MSI disk again? I did not, and the system seems to be fine, but I thought I was soupposed to do that after a CMOS reset.
4. Is there a new BIOS version for my setup that may be better now? Im currently on v1.5
Here is a screenshot from CPUZ of the system information currently. This is with it booting normally after my CMOS reboot. I just figured id post it incase it helps with any of my questions. Thanks so much for helping guys!

[URGENT HELP NEEDED] Premiere Pro CS6 failed rendering

Hello!
I`ll try to make this quick because I need help asap. I`ve been starting to make YouTube gaming videos 3 weeks ago and my channel is growing up pretty fast. I promised I would make a video everyday but it`s been a full week since I couldn`t upload because I was busy and when I tried to render it failed.
Anyway here`s how it goes.I`ve recorded with fraps some gameplay footage with the resolution of 1360x706. One of my friends reccommanded me Adobe Premiere Pro for editing so I`m using the trial version of CS6. I create a new project and choose a format of 720 25 (cant really remember the exact name). I then import my recorded files and when I place them in the sequence it tells me the resolution is different and asks me if I want to change the sequence settings according to the files. Usually, I ignore it and when I export the Media I just tick the option: "Scale to Fill" and that usually works just fine, quality HD on YT...
But this week it has driven me crazy, I really don`t want to explain how much stress and dissapointment this has caused to me because I think I`ll end up raging...I`ll just tell you I`ve been trying for a couple of days more than 7 time to render the project(each time it takes about an hour and a bit more, so let`s just call it 7 hours wasted). The problem actually is that when I check the output file after exporting the media, the file size is ONLY 24 bytes!!! Other times the file size gets to like half of the one that should be or less, but mainly the render even so takes up a normal length of time of processing but in the end the file is only 24 bytes..Thing is I don`t encounter any error whatsoever...
I really need some urgent help!
Thanks!

1st, some FRAPS information
These are for Premiere Elements, but may help with PPro
Fraps & Elements http://forums.adobe.com/thread/871095
-and more Elements http://forums.adobe.com/thread/943772
-and yet more Elements http://forums.adobe.com/thread/967201
2nd, it is REALLY better to have your project sequence match your video
Please NOTE that the PPro CS6 screen may look a bit different (I use CS5)
For CS5 and later, the easy way to insure that your video and your project match
See 2nd post for picture of NEW ITEM process http://forums.adobe.com/thread/872666
-and a FAQ on sequence setting http://forums.adobe.com/message/3804341

URGENT HELP NEEDED!!! (Almost a matter of life and death)

Well, it's more of a matter of failing a course or not...
Anyway, my Java professor gave us some labs to do. I know Java front and back, at least, whatever version I learned a few years back. This is my first tenure with the Scanner object, and it's messing me up.
I'm using Eclipse for my project. I have three files in the source folder, ABC_Manufacturing.java, mseast.dat and mswest.dat. Now, when I try to instanciate a new Scanner object, it won't find the files:
Scanner east = new Scanner(new FileReader("mseast.dat"));
Scanner west = new Scanner(new File("mswest.dat"));
I'm trying two seperate ways to do this. Neither are working, this is the error I get:
Exception in thread "main" java.lang.Error: Unresolved compilation problems:
     Unhandled exception type FileNotFoundException
     Unhandled exception type FileNotFoundException
     at ABC_Manufacturing.main(ABC_Manufacturing.java:38)
Now, I added these files OVER and OVER again. I added them. I created new files and pasted the contents in there. I used .txt files. All the same error. It's like it just won't take the time out to look for the files that are RIGHT IN THE DAMN PROJECT! Then I tried using a complete path, using C:\Java\whatever. SAME ERROR!!!!
Please, I need urgent help. This is due tomorrow at noon, and I have no idea what to do at this point. I can't really continue, because at this point its just looking at what prints out and formatting it, and I don't want to do that without testing to see if my code to convert the file data into arrays work. You dig? Thanks for any and all help, and I'm going to kill my professor...she spent a week going over parallel arrays but did nothing to show us how to import files into projects or use the scanner class. Also it doesn't help that at uni we have to use emacs, which I don't use at home.

d00erino wrote:
This is the the main class, so far:
public static void main(String[] args)throws IOException
          Scanner west = new Scanner(new File("mswest.dat"));
          int [] eastParts = new int[13];
          int [] eastQuant = new int[13];
          int [] westParts = new int[17];
          int [] westQuant = new int[17];
          System.out.print(west.nextInt());
And I didn't ignore that one guy (sorry, don't remember your username) I tried you and the other guy's responce. Both didn't work. I dunno how to get around errors. Figures, you don't learn that in the course but she'll spend a week on parallel arrays...Ok, well that can't possibly be complaining with the same error message you got before, so now you need to be (more) specific about what "didn't work" means.

Urgent Help Needed: ATI Graphics Card install

Hello All.... I am in need of some urgent help..
I am trying to install a new graphics card - the ATI Radeon 9600 SE. I currently have a Voodoo3 card. I followed all of the instructions step by step, but when I plug the monitor to the Radeon card and boot up, I do not get any display. I have tried everything I can think of, and yet - I am sure the card is secured in place and the monitor is plug into the card.
Can anyone help me on this one.. ATI's support is, well - lacking..
Here is some info on my pc:
MCI motherboard
AMD Athlon(tm) XP 2000+ 1.7 GHz
768 MB
AMIINT - 10 Version 1.00, 07/10/02
Could the problem be with switching from a regular PCI card to an AGP card???

Quote
Originally posted by southmike
okay i'll bite what are omega drivers,
how are they different from cat4.2 drivers
i was suprised that the voodoo 3 would work in a AMD64 mobo...
whoops....just read the rest of the post :lol:
BTW is there an external power connector that needs to be plugged in?

Urgent help needed(java frames)

Hi,
I need urgent help for correcting a piece of code.
I have written a piece of code for building a gui with some buttons, drawing some geometric shapes.The code consists of two files called Graph and Frame.
The problem I suppose in the last part of the Graph file, which Rectangle and Circle are called together, the only shape that the program draws is rectangle.Here is the code:
//Graph
import java.awt.*;
import java.awt.event.*;
import javax.swing.*;
import javax.swing.event.*;
import java.io.*;
import java.util.*;
public class Graph extends JPanel {
LinkedList color;
LinkedList figures;
public Graph() {
setBackground(Color.white);
figures = new LinkedList();
color = new LinkedList();
int z;
class Point {
int x;
int y;
public Point(int x, int y) {
this.x = x;
this.y = y;
public Point(Point p) {
x = p.x;
y = p.y;
public String toString() {
return "(" + x + ", " + y + ")";
public void move(Point dist) {
x += dist.x;
y += dist.y;
abstract class GeomFigur {
public abstract void move(Point p);
class Line extends GeomFigur {
Point p1, p2;
public Line(Point p1, Point p2) {
this.p1 = new Point(p1);
this.p2 = new Point(p2);
public String toString() { return "Line from " + p1 + " to " + p2; }
public void move(Point dist) {
p1.move(dist);
p2.move(dist);
class Rectangle extends Line {
public Rectangle(Point p1, Point p2) {
super(p1, p2);
public String toString() { return "Rectangle from " + p1 + " to " + p2; }
class Circle extends GeomFigur{
Point centre;
int radius;
public Circle(Point centre, int radius) {
this.centre = new Point(centre);
this.radius = radius;
public String toString() {
return "Circle, centre " + centre + ", radius " + radius;
public void move(Point dist) { centre.move(dist); }
public void addRectangle(int x, int y, Color col) {
Rectangle r =new Rectangle(new Point(x,y),new Point(x+20,y+20));
figures.addLast(r);
color.addLast(col);
repaint();
public void addCircle(int x, int y, Color col) {
Circle c =new Circle(new Point(x,y), 1 );
figures.addLast(c);
color.addLast(col);
repaint();
public void paintComponent(Graphics g) {
super.paintComponent(g);
for (int i=0;i < figures.size();i++) {
Rectangle rect = (Rectangle)figures.get(i);
//Circle circ = (Circle)figures.get(i);
g.setColor(Color.black);
g.drawRect(rect.p1.x,rect.p1.y,20,20);
g.setColor((Color)color.get(i));
g.fillRect(rect.p1.x,rect.p1.y,20,20);
//g.setColor(Color.black);
// g.drawOval(circ.centre.x,circ.centre.y,20,20);
// g.setColor((Color)color.get(i));
// g.fillOval(circ.centre.x, circ.centre.y, 20, 20);
//Frame
import javax.swing.*;
import java.awt.*;
import java.awt.event.*;
import java.io.*;
public class Frame extends JFrame implements ActionListener {
JButton button1, button2, button3, button4, button5 ;
Graph gr;
JComboBox cbx;
JComboBox cby;
JComboBox col;
JMenu filemenu;
JMenuItem quit;
JMenuBar menubar;
int x=10;
int y=10;
Color color=Color.red;
public Frame() {
menubar = new JMenuBar();
filemenu = new JMenu("File");
filemenu.setMnemonic('F');
quit = new JMenuItem("Quit");
quit.addActionListener(this);
quit.setMnemonic('Q');
quit.setAccelerator(KeyStroke.getKeyStroke('Q',Event.CTRL_MASK,false));
filemenu.add(quit);
menubar.add(filemenu);
setJMenuBar(menubar);
button1 = new JButton("Rectangle");
button1.addActionListener(this);
button2 = new JButton("Circle");
button2.addActionListener(this);
button4 = new JButton("Ellipse");
button4.addActionListener(this);
button5 = new JButton("Triangle");
button5.addActionListener(this);
button3 = new JButton("Reset");
button3.addActionListener(this);
String[] elements_x= {"10","20","30","40","50","60","70"};
cbx = new JComboBox(elements_x);
cbx.addActionListener(this);
cbx.setActionCommand("cbx");
String[] elements_y= {"10","20","30","40","50","60","70"};
cby = new JComboBox(elements_y);
cby.addActionListener(this);
cby.setActionCommand("cby");
String[] elements_color = {"Red","Blue","Green","Orange","Yellow" };
col = new JComboBox(elements_color);
col.addActionListener(this);
col.setActionCommand("col");
gr = new Graph();
JPanel top = new JPanel(new BorderLayout());
JPanel inputs = new JPanel(new GridLayout(6,1));
inputs.add(button1);
inputs.add(button2);
inputs.add(button3);
inputs.add(button4);
inputs.add(button5);
inputs.add(cbx);
inputs.add(cby);
inputs.add(col);
top.add(gr,BorderLayout.CENTER);
top.add(inputs,BorderLayout.WEST);
getContentPane().add(BorderLayout.CENTER, top);
setSize(500,300);//set window size
//take care of actions
public void actionPerformed(ActionEvent e) {
String command = e.getActionCommand();
if (command.equals("Quit")){
System.exit(0);//terminate program
else if (command.equals("Rectangle")){
//add Rectangle to graph at
//position x,y and with certain color
gr.addRectangle(x,y,color);
else if (command.equals("Circle")){
gr.addCircle(x,y,color);
else if (command.equals("Reset")){
else if (command.equals("Triangle")){
else if (command.equals("Ellipse")){
else if (command.equals("cbx")){
x=Integer.valueOf((String)((JComboBox)e.getSource()).getSelectedItem()).intValue();
else if (command.equals("cby")){
y=Integer.valueOf((String)((JComboBox)e.getSource()).getSelectedItem()).intValue();
else if (command.equals("col")){
String temp=(String)((JComboBox)e.getSource()).getSelectedItem();
if (temp=="Red") color=Color.red;
else if (temp=="Blue") color=Color.blue;
else if (temp=="Green") color=Color.green;
else if (temp=="pink") color=Color.pink;
else if (temp=="lightGray") color=Color.lightGray;
//main program
public static void main(String [] args) {
Frame appl = new Frame();
appl.setVisible(true);
Thanks in advance
Marina

Hi,
You are very lucky that I'm currently boored. You should never tag a question as urgent. It might be urgent to you, but not to us who answer. And you should also use code formatting when you post code (see the formatting tips, or use the code-button).
I made some changes to your Graph class. The most important thing is the abstract draw method that I added to the GeomFigur class.
import java.awt.*;
import javax.swing.*;
import java.util.*;
public class Graph extends JPanel {
    LinkedList figures;
    public Graph() {
        setBackground(Color.white);
        figures = new LinkedList();
    int z;
    abstract class GeomFigur {
        protected Color color;
        public GeomFigur(Color color) {
            this.color = color;
        public abstract void move(Point p);
        public abstract void draw(Graphics g);
    abstract class Line extends GeomFigur {
        Point p1, p2;
        public Line(Color c, Point p1, Point p2) {
            super(c);
            this.p1 = new Point(p1);
            this.p2 = new Point(p2);
        public String toString() {
            return "Line from " + p1 + " to " + p2;
        public void move(Point dist) {
            p1.move(dist.x, dist.y);
            p2.move(dist.x, dist.y);
    class Rectangle extends Line {
        public Rectangle(Color c, Point p1, Point p2) {
            super(c, p1, p2);
        public String toString() {
            return "Rectangle from " + p1 + " to " + p2;
        public void draw(Graphics g) {
            System.out.println("Draw rectangle at " + p1 + " with color " + color);
            g.setColor(Color.black);
            g.drawRect(p1.x, p1.y, 20, 20);
            g.setColor(color);
            g.fillRect(p1.x, p1.y, 20, 20);
    class Circle extends GeomFigur {
        Point centre;
        int radius;
        public Circle(Color c, Point centre, int radius) {
            super(c);
            this.centre = new Point(centre);
            this.radius = radius;
        public String toString() {
            return "Circle, centre " + centre + ", radius " + radius;
        public void move(Point dist) {
            centre.move(dist.x, dist.y);
        public void draw(Graphics g) {
            System.out.println("Draw circle at " + centre + " with color " + color);
            g.setColor(Color.black);
            g.drawOval(centre.x, centre.y, 20, 20);
            g.setColor(color);
            g.fillOval(centre.x, centre.y, 20, 20);
    public void addRectangle(int x, int y, Color col) {
        System.out.println("x,y,col " + x + ":" + y + ":" + col);
        Rectangle r = new Rectangle(col, new Point(x, y), new Point(x + 20, y + 20));
        figures.addLast(r);
        repaint();
    public void addCircle(int x, int y, Color col) {
        System.out.println("x,y,col" + x + ":" + y + ":" + col);
        Circle c = new Circle(col, new Point(x, y), 1);
        figures.addLast(c);
        repaint();
    public void paintComponent(Graphics g) {
        super.paintComponent(g);
        for (int i = 0; i < figures.size(); i++) {
            GeomFigur drawable = (GeomFigur)figures.get(i);
            drawable.draw(g);
}/Kaj

Urgent Help : Workflow Problem

Similar Messages

Maybe you are looking for