Urgent NAT-T DMVPN help?

can some one please provide me with the configuration of the DMVPN hub-server when the hub-server is configured with nat???
i`ll be thankfull.............

Hi Mohammed,
I think you may want to check these links:
NAT-Transparency Aware DMVPN
"Also added in Cisco IOS Releases 12.3(9a) and 12.3(11)T is the capability to have the hub DMVPN router behind static NAT. This was a change in the ISAKMP NAT-T support. For this functionality to be used, all the DMVPN spoke routers and hub routers must be upgraded, and IPsec must use transport mode.
For these NAT-Transparency Aware enhancements to work, you must use IPsec transport mode on the transform set. Also, even though NAT-Transparency (IKE and IPsec) can support two peers (IKE and IPsec) being translated to the same IP address (using the UDP ports to differentiate them), this functionality is not supported for DMVPN. All DMVPN spokes must have a unique IP address after they have been NAT translated. They can have the same IP address before they are NAT translated."
Static NAT & DMVPN Hub ---> Another similar post.
Hope it helps.
Thanks.
Portu
Message was edited by: Javier Portuguez

Similar Messages

  • How to implement drop down list in WDP Abap....very urgent...please help me

    Hi Gurus,
    I wanted to implement the drop down list button in the WDP Abap interactive form. Once the users clicks on the drop down button, an RFC should be called and display the details under the drop down button. Please give me the logic with code. Its very urgent...please help me. Please note that it is in WDP Abap interactive forms. We are using NW2004S, ECC6.0.

    Hello,
    you have to use ZCI form to use DDLB in WD-ABA. The content of the DDLB has to be present at rendering time, there is no dinamic call when you click the "dropdown".
    The attribut you map to the DDLB has to be an element with a value-set, and the value set has to contain the text / value pairs.
    >> this will be displayed when you click the dropdown.
    Best regards,
    Dezso

  • I cant use the highlight, underline, or strikethrough function in a specific pdf file. The file isnt locked. I used to highlight texts from that file before the latest update. The problem occurs only with that file. Urgent need. Please help. Thanks!

    i cant use the highlight, underline, or strikethrough function in a specific pdf file. The file isnt locked. I used to highlight texts from that file before the latest update. The problem occurs only with that file. Urgent need. Please help. Thanks!

    Chester31,
    Thank you very much for sharing your file with us!  Now that we are able to reproduce the problem at our end, you may stop sharing the file on Acrobat.com.
    Do you know when this problem (for not being able to add new highlight/strikeout/underline) has started?  Did you update your iOS from 7.x to 8.0 recently?
    We will continue investigating the problem and let you know what we find.
    Thank you again for your help.

  • I just got the iphone 4s and my text messages are showing as urgent to others,please help me fix this

    i just got the iphone 4s and my text messages are showing as urgent to others,please help me fix this

    As ckuan said, there's no way to mark messages as urgent from the phone. So, either your carrier is doing something and you'll need to contact them or it't something on the other end. Is it just one person who's seeing your texts as urgent? Or everyone?

  • Urgent... need help in alv.

    hai all,
    in an alv report i want a pushbutton in the application tool bar .
    how can i get it.
    and also i want to select multiple rows from the list and the first column as a button to select the rows.
    please.. help me. its very urgent.
    thanks in advance.
    regards, selvi.

    Hi,
    Following steps to copy standard status to zstatus
    Goto T.Code  SE41 & give program name SAPLSLVC then select
    status as STANDARD then copy this status to zstatus in your program
    open zstatus in T.Code SE41 and  add push button and  save & activate it.
    then Call FM  PF_STATUS.
    see below,
    I_CALLBACK_PF_STATUS_SET- 'PF_STATUS'
    In module PF_STATUS
    set pf-status 'ZSTATUS'
    reward if useful.

  • CIDX -XI-IDOC adapter scenario???????? urgent?? pls help

    Hi Frnds,
    I want to develop scenario between  CIDXXIIDOC..
    if any one having documentation about CIDX
    any scenario withs screene shots share to me...
    share any useful links,
    what are challenges i wil face while developing CIDX adapter scenario
    anyone help me out.. its very urgeNT......
    Regards,
    RAJ

    Hi,
    CIDX Adapter is Chemical Industry standard for data exchange in B2B scenarios. It uses XML formatted in different manner specific to Chemical industry.
    In order to use this, you need to purchase the license.
    There are xml schemas provided by CIDX for each transaction like Order Create, Order change, shipping instruction etc..
    You need to download the once which are required in your scenario and use the same.
    For overview of CIDX in general you can visit http://www.cidx.org
    This might give u an business scenario -http://www.rexsoft.com/sci/Rex_CPI_XI_Configuration_Testing_Business_Package.pdf
    Hope this helps too...
    http://help.sap.com/saphelp_nw04/helpdata/en/23/cb22419e2ab167e10000000a155106/frameset.htm
    http://help.sap.com/saphelp_nw04/helpdata/en/f4/622c41eda5f423e10000000a155106/frameset.htm
    http://help.sap.com/saphelp_nw04/helpdata/en/d5/351941fcdbf56fe10000000a1550b0/frameset.htm
    Check this basic guide too..
    https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/915dc712-0b01-0010-a99a-fb2fdfa5ddc2
    Check these forum replies too..
    CIDX and R/3
    Please reward points.
    Thanks,
    Vijaya.
    Edited by: Vijaya Lakshmi Palla on Jun 5, 2008 8:37 AM
    Edited by: Vijaya Lakshmi Palla on Jun 5, 2008 8:42 AM

  • Urgent: Sessions problem pls help me

    Hi all,
    Its already late to post this problem.pls help me urgently.
    I have a servlet & two jsp's. first i request servlet, it processes something and forwards request to my first jsp. In that jsp on a button click, i'm displaying a new popup by calling showModalDialog. this dialog gets data from the same servlet but it forwards to my second jsp.(second jsp can be seen in dialog)
    Now if i submit form from my second(dialog) jsp, the servlet reports that session has expired. I tried a lot but invain. any one who helps me is appreciated well by all of our forum.
    waiting 4 u r reply,

    It could be that you have cookies turned off and you're not using URL Rewriting.
    In J2EE, the first time your browser makes a request to the server, the server responds and appends a SESSION_ID parameter to the request as well as storing a cookie with the SESSION_ID.
    The second time your browser makes a request, the server checks for the cookie. If it doesn't exist it checks for the parameter. If neither exist the server assumes its the first time your browser has made a request and behaves as describe in the previous paragraph.
    In your case when you submit the form if you have disabled cookies and the action attribute doesn't have the SESSION_ID paramter appended to the url, the browser will assume it's a first request. The user will not be logged in, hence your session has expired error.
    To fix this you need to encode the URL in your JSP. You can use the struts html:rewrite tag or the HttpServletReponse.encodeURL method, or if you're using JSP 2.0 the JSTL c:url tag.

  • Have problem in install!!! Urgent!!! Help!!!

    Runtime exception during validation of variable :nValidationPortListSelect
    java.lang.NullPointerException
    Runtime exception during validation of variable :nValidationInstanceInfo
    java.lang.NullPointerException
    java.util.zip.ZipException: invalid entry CRC (expected 0x67aa7f54 but got 0x42cd673e)
    What could be the problem? Help me it is urgent?

    First of all, would you mind sharing the details of your installation? OS, Oracle version etc.?
    java.util.zip.ZipException: invalid entry CRC (expected 0x67aa7f54 but got 0x42cd673e)
    Looks like a possibly corrupt download.

  • NAT on 2621 HELP!!!

    I have spent a few hours trying to NAT out a few intenal 192.168.x.x hosts through both my ethernet1/0 interface and also tryed using another IP from the range. Any help GREATLY appreciated. Thanks! (Config below)
    Building configuration...
    Current configuration : 1021 bytes
    version 12.3
    service timestamps debug datetime msec
    service timestamps log datetime msec
    service password-encryption
    hostname 2621
    boot-start-marker
    boot-end-marker
    enable secret xxxx
    enable password xxxx
    no aaa new-model
    ip subnet-zero
    ip name-server xx.xx.xx.xx
    ip name-server xx.xx.xx.xx
    ip audit po max-events 100
    interface FastEthernet0/0
    ip address 65.126.x.x.x.255.252
    duplex auto
    speed auto
    interface FastEthernet0/1
    ip address 192.168.1.1 255.255.255.0
    ip nat inside
    speed auto
    half-duplex
    interface Ethernet1/0
    ip address 65.126.x.x.x.255.240
    ip nat outside
    half-duplex
    ip nat inside source list 7 interface Ethernet1/0 overload
    no ip http server
    no ip http secure-server
    ip classless
    no ip route static inter-vrf
    ip route 0.0.0.0 0.0.x.x.x.121.117
    line con 0
    line aux 0
    line vty 0 4
    password xxx
    login
    end

    7 years old post but i have the CCNA Composite exam in 36 hours so i'll ignore that and answer.
    I'm assuming a basic setup (like the one in the question) with PAT and many-to-one source translation.
    The steps to properly configure NAT are:
    1) list all your interfaces and track which ones are your *internal* interfaces and which one is your *external* one. In the configuration given by OP, the "inside" interface is Fastethernet 0/1. The "outside" interface is Ethernet 1/0.
    2) Declare the interfaces one by one, this is done in the interface configuration dialog with the statement "ip nat inside" and "ip nat outside" for the respective interfaces.
    3) Gather your traffic, with an ACL. This step is necessary to teach the router which traffic he should consider for Network Address Translation. It is achieved by an acl that permits traffic coming from the subnets configured on our "inside" interfaces. In this case, 192.168.1.0/24.
    segillett wrote:thanks joe, since I posted i caught that and have this in thereaccess-list 7 permit 192.168.1.0 0.0.0.250it still does not. I am really at a loss here sitting in the datacenter at 9;30pm. Do I need to route the 192.x.x.x somewhere (tried all options), thanks for any more advice.
    The reason OP can't get NAT to work is because his ACL was at first absent, and subsequently mistyped.
    It should be
    ip access-list standard 7
    permit 192.168.1.0 0.0.0.255
    deny any
    The deny statement is implied but explicitly adding it simplifies troubleshooting as every packet matching it will show up in
    # show access-lists
    ACLs use a "wildcard" mask notation for defining  groups of addresses. For all intents and purposes at this level, they  are just another format  for the subnet masks but they can be used in  other ways.
    You obtain your wildcard mask by subtracting the  subnet mask bits (in decimal) from 255.255.255.255. In this case:  255.255.255.255 - 255.255.255.0 (the subnet mask for a /24 network) =  0.0.0.255. Therefore, the mistake lies in the ACL statement.
    4) Activate NAT with the general configuration dialog statement "ip nat inside source list LISTNAME interface INTERFACEID overload
    5) Troubleshoot if needed by using show access-lists, show ip nat translations, debug ip nat . It only works when you see relevant data in the output of those commands.
    You do *not* have to route anything, as that would defy the entire purpose of NAT.
    If i made any mistake in my post please point it out. I think i got my head around NAT pretty ok but you never know.
    Any feedback is welcome.
    G.

  • Very Urgent...Please Help..Invoking Windows Applications

    I capture the Windows Desktop screen and saved it as a .jpg file. I then display the .jpg file on frame ( whose size is that of the screen ). Now if i click on the frame, the corresponding Window's application should be invoked ( i.e if I click on the frame where the Start Menu is shown, then the Start Menu should be opened ). Please help me with the code for this. I will be forever indebted to the person who can help me. Iam in very urgent need of this help

    Not so easy.A JPG file is a compressed map of a "picture",nothing more. So , You have to get a reference to an object of this map - You can't save to a simple file (JPG) and expect to do what you want to do.Think something else , not a simple snapshot.In Win98 you have a directory "Desktop" where are all of your icons , in Win2000 you have to search in "Documents and settings\User_name\" or something like this to find the same directory and get all icons.Therefrom look for "Properties" and find the path to execute the exe file.It must be something like this I think.Hope have been helpfull.

  • Urgent :: FRM-40654 || pls help me out

    Hello forum
    Pls i need an immediate help. so suggestions invited...
    i have a block having 1 db item and 1 non db item . i m shoving LOV for filling those..
    these 2 are displayed multiple times on the canvas.
    i want that whn user select one from LOV then in ssecond entry it will not appear in the LOV so i write a query in the LOV.
    select a,b from <table1> where a not in (select a from table2 where <primary key condtions>
    for getting data from table 2 i have to post the data which is in the canvas so i write post on button- press
    so it's giving me error
    FRM-40654 other user updated the table so need to requery
    so pls help me out in resloving this prob'

    hello forum
    pls help me out ... i m in urgent need .
    thanking u

  • Remedy issue URGENT!! Please help

    Hi All,
    I am not able to login to remedy client as I'm getting the below error
    *‘RPC: Miscellaneous tli error - System error (Connection refused)’*
    We tried to restart the remedy process, that dont work, Getting the below SQL errorAction Request System initializing.
    Starting Remedy AR System server
    Also I have checked the network/firewall as there is no issues with their end.
    Please anyone help me to resolve this issue.
    Error while restarting the remedy process
    Action Request System(R) Server Version 4.05.02 patch 1025
    Copyright (c) 1991 - 2001 Remedy Corporation. All Rights reserved.
    Copyright (c) 1989 - 2001 Verity, Inc. All rights reserved.
    Reproduction or disassembly of embodied programs and databases prohibited.
    Verity (r) and TOPIC (r) are registered trademarks of Verity, Inc.
    390600 : SQL database is not available -- will retry connection (ARNOTE 590)
    Notification System Server Version 4.05.02
    Copyright (c) 1994 - 2001 Remedy Corporation. All Rights reserved.
    110902110300- 24733: Initializing process 24733
    110902110300- 24733: DISPLAY_CONFIGURATION===================================
    110902110300- 24733: EXTERNAL START (-X) FALSE
    110902110300- 24733: RESTART (-r) FALSE
    110902110300- 24733: Check-Users: (-c) FALSE
    110902110300- 24733: Debug-Level: (-d) 21
    110902110300- 24733: Disable-Shared-Memory: FALSE
    110902110300- 24733: Hold-Time: (-h) 2592000 seconds = 30.0 days
    110902110300- 24733: Max-Users: (-u) 1000
    110902110300- 24733: Notifier-Outbound-Port: 0
    110902110300- 24733: Notifier-Specific-Port: 0
    110902110300- 24733: Private-RPC-Socket: 0
    110902110300- 24733: Private-Specific-Port: 0
    110902110300- 24733: Register-With-Portmapper: FALSE
    110902110300- 24733: Send-Timeout: (-t) 7
    110902110300- 24733: TCD-Specific-Port: 32768
    110902110300- 24733: ========================================================
    110902110300- 24733: AR System server: remedy01
    110902110300- 24733: AR ServerNameWithDomain: remedy01.ndc.lucent.com
    110902110300- 24733: HostnameWithDomain: remedy01.ndc.lucent.com
    110902110300- 24733: StartServerDaemons
    Notification Send Server Version 4.05.02
    Copyright (c) 1991 - 2001 Remedy Corporation. All Rights reserved.
    110902110300- 24736: Initializing process 24736
    110902110300- 24736: ProcessFiles: called with loginFd(0)=9 and notificationFd(1)=10
    110902110300- 24736: ProcessFiles: start Notifications at offset 0.
    110902110300- 24736: ProcessFiles: reopening nfyfile (new notificationFd=10)
    110902110302- 24733: StartServerDaemons daemon 0 started
    Action Request System(R) Mail Daemon Version 4.05.02
    Copyright (c) 1991 - 2001 Remedy Corporation. All Rights reserved.
    MailFileName: /usr/mail/fxbrophy
    Action Request System initialization is complete.
    390600 : Cannot initialize contact with SQL database (ARERR 551)
    Stop server
    390600 : AR System server terminated -- fatal error encountered (ARNOTE 21)
    Action Request System(R) Server Version 4.05.02 patch 1025
    Copyright (c) 1991 - 2001 Remedy Corporation. All Rights reserved.
    Copyright (c) 1989 - 2001 Verity, Inc. All rights reserved.
    Reproduction or disassembly of embodied programs and databases prohibited.
    Verity (r) and TOPIC (r) are registered trademarks of Verity, Inc.
    390600 : SQL database is not available -- will retry connection (ARNOTE 590)
    Thanks,
    Sajith

    Why are you posting this on the Oracle forums, shouldn't you be talking to Remedy or BMC or whoever provides support for the product?
    Also this (or other public forums) is generally not the place for urgent production issues. There are paid support channels for such issues.
    Anyway, a hint:
    I would probably dig into the very vague "SQL database is not available" message. Does the system have details in logs? What clues does the actual/underlying error messages provide? Is the database in question actually up and reachable from the client (i.e. app server) host?
    Edited by: orafad on Sep 26, 2011 2:20 PM

  • E1000 + PS3 =NAT Type 3 Help

    I know this has been asked before but nothing seems to work for me. My story is:
    I had a WRT150N with a modem in bridge mode and got NAT Type 2 while playing the PS3. The router crashed and I got an E1000 in its place it came with the basic setup CD so I ran that. Then I was getting NAT Type 3. So I called Linksys, and AT&T and neither could help me we opened the ports that Playstation gave me and made sure the UPnP was enabled and all the things they could think of to open my NAT type. But nothing has worked, so if anyone knows anything I could do please let me know. Its just hard to believe that its my playstaion when I had an NAT Type 2 before my old router crashed. I'll supply screen shots whatever you need, I just cant stand to have this NAT type cause it messes with my online gaming.
    Thanks for the Help,
    Grant
    Solved!
    Go to Solution.

    Did you set up PPPoE for the new router and put your modem into bridge mode? 
    I don't work for Cisco. I'm just here to help.

  • Urgent typical problem- Please help!!

    Dear All,
    I have a BOM material(say M) which is made up of 3 components(say A, B and C).
    I procure component A from 3 different countries(T1, T2 andT3), component B from 2 different countries(T4 and T5) and component C from 4 different countries(T6, T7, T8 and T9).I process them and prepare a finished good ‘M’(as mentioned above) and export it. I want to track the country of origin of each of the components of this BOM.How can I achieve this?
    To make my question more clear…..If I am exporting material M, I should be able to track all the 9 countries(T1…..T9) because M is made up of 3 components procured from 9 countries(in all).
    Since the problem is critical, I would appreciate your urgent help on this.Thanks!!

    Hi Reshu
    You can certainly download list of components that are imported and its vendor's name through a query as follows:-
    1)  Goto SQVI
    2)  Table join MBEW and EORD
    3)  Select the Valuation Class field BKLAS in MBEW and LIFNR in EORD
    4)  In Valuation Class, give 3002 & 3003 (Imported Duty Paid & Duty Free)
    5)  Execute the report
    A report will be generated wherein you can see all imported components and its respective vendor list.
    I think you only have to decide which particular component goes into which assembly and no report is available to my knowledge.  Others correct me if I am wrong.
    By the way, I am sure, the above suggestion will be helpful to a great extent and if so, dont forget to reward points please.
    Thanks
    G. Lakshmipathi

  • Urgent BBM Instant Messaging Help!

    Good Day,
     I am inquiring about BBM Instant Messaging service. Are there any features that can allow a company to create a group without a limit on the amount of members that can be added, for the purpose of connecting with customers through a means apart from social networking websites? Or is there any other Blackberry service that will allow the company to do the required? An urgent response will be greatly appreciated.
    Thank you in advance

    mitsouko85 wrote:
    I don't find the tools
    And i have also small police in message or sms 
    Please can you help me?
    When i click on skype menu i have about skype - preferences - provide skype feedback - etc
    Are you on a Windows computer? What is your Skype version? In Skype go to Help -> About Skype.

Maybe you are looking for