URGENT: PXI-1033 and DAQmx problem

I bought new laptop with Express Card slot Dell Inspiron 6400. I have PXI-1033 with integrated MXI bridge, Express Card 8360 and PXI-modules: PXI-6251, 6115, 5114 and 4071. I installed drivers 8.3 and plugged in PXI modules into PXI-1033. I first power up PXI-1033 and than power up laptop (with Express Card in it). Laptop can not start, again can not, blue window, and at last start. In MAX is listed PXI chassis with bridge and all modules, but mx is not listed and I can not use it from LabVIEW. What is the problem?

Hi,
To clarify, do the PXI modules show up under DAQmx devices? What color is the Link LED on the 1033? Do the cards all show up in Windows Device Manager correctly? Also, are you able to power on the laptop successfully now every time, or does is have trouble booting each time you try and start it up?
Have you inspected the MXI cable for bent pins or any visible damage?
Thanks!
Adam W
Applications Engineering
National Instruments

Similar Messages

I got Internal Software Error -223044 with my PXI-4472, PXI-1033 and NI expresscard-8360 DaqMx 8.8

When i running the self test of the board in MAX i got error -223044, anyone that has some ideas??
STALT

Hey Stalt,
This particular internal error begs me ask a few questions.
1) Has this 4472 ever been used with DAQmx?
2) How old is this 4472? When was it bought from NI? Can you give me the revision letter of the board? That is found by looking for a number printed on the board that usually begins with "ASSY", then there are several other numbers/letters, but the one letter I care about is the letter right before the "-" So it would look like ASSY11111111E-01 so the revision would be "E"
3) Do you have another PXI system (with DAQmx) that you can initialize this 4472 in?
Let me know
-gaving
Software Engineer
National Instruments

PXI-4351 and DAQmx?

Hello,
We are considering to buy a PXI-Chassis with an PXI-6229 for general measurement and two PXI-4351 for temperatur measurements.
I already wrote a big library of VIs to use PCI and PXI-card undere DAQmx (almost 6 months of development).
But I read in the specification of the PXI-4351 that this card is only supported by the traditional DAQ driver.
Is it true, are may be the DAQmx 8.1 support the PXI-4351. If not, does anybody know if the card will be soon part of the DAQmx?
Thanks,
Risotto

Risotto,
the PXI-4351 works quite differently than a multifunction DAQ device and it comes with it's own instrument driver which is based on traditional NI-DAQ. The instrument driver was just updated to support LV 8. There are currently no plans to support NI-435x devices with NI-DAQmx
Best regards,
Jochen Klier
National Instruments Germany

How to control a solenoid via PXI-2520 and DaqMx Switch

I am a LabView novice with Core 1 and Core 2 training so I am familiar with the fundamentals of LV process flow however, this is the first application I am attempting to develop that is not a simulated training VI. That said, I am having trouble ironing out the necessary logic to control a 10 solenoid 2 position valve manifold. I have developed a VI that will contact and disconnect a particular relay in the style of the "Switch Controlling Individual Relay.VI" on my PXI-2520 module but these are single instance events. Ie. i set the device, name the relay, and tell the VI which action (make or break) and run the VI. What I am trying to develop is a continuously running VI where any one or multiple solenoids can be energized/de-energized using simple boolean control whereby each relay is represented by a switch on the front panel.
It is clear that a while loop is necessary and a series of case structures or State Machine architecture is necessary but all my attempts have been fruitless. the common failure mode tends to be when following iterations of the while loop tell a switch that is already open to reopen or vise versa thereby causing an error. My thought here ist that some feedback from a former iteration is necessary so that only "unequal" boolean values for the former iteration calls a case to connect/disconnect. What are your thoughts?
Eventually this VI will also need to control these solenoids automatically (i think DaqMx Create scan list with software triggers will suffice) but each action willl need to be timed. For now though it is most critical that I have the capability of operating the solenoids manually and dynamically.
Thankyou,
DK01

Welcome to the forums!
If you can, please post a snippet of code from what you've attempted so far. We can take a look at it and make some recommendations.
One of the lessons in Core 1 also talked about the use of the event structure. It may be a good use case for an event driven state machine that can modify the states of specific switches.
Nathan M.
Applications Engineer
National Instruments

Suitable Laptop for PXI-1033

I am using a PXIe-8360 with a PXI-1033 and am trying to find a laptop that is compatible with this system. NI states that not all laptops work with this configuration and has a list of laptops that do have been tested at (http://zone.ni.com/devzone/cda/tut/p/id/5035). This list is outdated and NI does not give any criterion on how to select a laptop that will work with this system on the webpage. We have purchased an Acer 5680 and it doesn't seem compatible. Is there a more recent list of laptops that are compatible?

Hi PP83,
I am afraid that the knowledgebase article you located (http://zone.ni.com/devzone/cda/tut/p/id/5035) has the most up-to-date information regarding compatibility between laptops and the Expresscard-MXI for PXI and PXI Express. National Instruments is actively testing motherboards and laptops so that we can comment on compatibility with our MXI products.
For information on motherboards, desktops, and workstations compatible
with MXI products, you can create a service request with National Instruments PXI Support group at ni.com/support.
Regards,
Anna M.
National Instruments

NI PXI-4065 attached to PXI-1033 strange problem

Hi all,
I have a NI PXI-1033 Chassis together with NI PXI 4065 DMM and NI PXI 6514 device.
The problem that I have is very annoying. When I restart my computer or install a new NI feature, the two NI PXI-6514 and PXI 4065 are no longer available as shown at the picture attached and I have to reinstall the drivers in order they to function properly. Why is this happening? Is it normal?
I will appreciate every help because it is urgent and important. Thank you!
Best,
Iliya Gurov
Attachments:
problem.JPG ‏42 KB

I know this topic is ancient but I'm having a similar problem with my system:
PXI-1033 (thru external PC / PCIe)
DAQmx 9.2.2
LabVIEW 8.5
Windows 7 (32-bit)
When starting MAX it gives the MAXPXITimeout error. Then MAX crashes most of the time or when it works, none of the devices are "present" according to MAX, i.e no initialize, fail self-test, etc. I tried this command "net start nidevldu" and I get a "windows system error 5 - access denied". So I ran the command prompt as administrator and then the NI Device Loader "successfully started". Now MAX works OK and all my devices are working, until next reboot. Is this a permission issue? I tried changing the NI Device Loader service to log as an admin, but no luck. After rebooting the same issue.
Appreciate the help. Thanks,

Problems with the link between PXI chassis and PC via MXI-4

MAX display the chassis with a yellow exclamation point, and the MXI-4 conection monitor indicates taht the connection to the chassis has timed out.
Under the windows device manager appears PCI std PCI-to-PCI bridge and MXI-4 connection monitor working properly.
The system has bben working properly for one year and suddenly start to fail.
I've tried to uninstall fromn device manager and reinstall again, and teh problem continues. When the PC starts detect new hardware and reinstall from CD with MXI-4 software for windows v 1.0
Only the led PWR lights. The link indicator remains always off, from power up continuously. The cable connection has benn checked ok.
The chassis is powered up in the proper sequence, first the PXI chassis, and the the PC.
Operating system windows XP service pack 2; latest update KB835732 30/12/2004 (V 6.2)
labwindows/cvi (fds) 7.0
ivi compliance oackage 2.1.2
max 3.1
ni-daq 7.3
visa 3.1
chassis pxi-1000b with PXI-8331.

Hello,
it could it be an incompatibility with the desktop PC (maybe?). I know of cases in which the PCI board can be incompatible with a certain PC for various reasons (PCI bus not 100% compliant to PCI standards, PCI power rails, PCI bus-master capabilities, motherboard/chipset issues, etc..).
I mean, has the PC been changed?
Wich PC model/brand is it?
Have you tested it on another of PC (another model)?
In case you have already tested your mxi-4 in other PCs and the behavior is the same, I suggest you to contact your local NI office for assistance.
Regards,
Jorge M.

Step and Repeat Problem in CS3-Urgent!

I was working on a file, step and repeats was working just fine. Then suddenly within the same file it got messed up somehow.
Whenever I type in a decimal point (say 4.5) and I move on to the next field it will default to a higher number (say 5). It is not letting me do decimal points!
I did replace preferences (and yes I got the pop up on the start menu). And the problem is still there.
And it happens in all files, not just the one.
Please help, the MUST be working right or else I can't do my job!
CS3 5.0.4 Mac 10.5.8

Well, it wasn't. But I rebooted again (after replacing preferences) and so far it seems ok. Weird.
I'll post back up again if I have any problems.

Can't configure a SCXI chassis (PXI-1010) with a PXI-8176 and a PXI-6052E.

I have a PXI-1010 chassis with a PXI-8176 running Windows 2000. In the rightmost PXI slot, I have a PXI-6052E. The remaining PXI slots are either empty or have misc. modules in them. I have a SCXI-1520 in the leftmost SCXI slot.
I am trying to get MAX to recognize my SCXI chassis with the SCXI-1520. When I try to add the SCXI chassis in MAX by right-clicking "Devices and Interfaces" or "NI-DAQmx", I leave the communication mode to communicate on the PXI backplane, choose SCXI slot zero, and find that the communication device field is greyed out where I want to choose the PXI-6052E. For some reason,the wizard used to add an SCXI chassis does not see my PXI-6052E pluged in to the leftmost sl
ot. Strangely, MAX does see the PXI-6052E in the "Devices and Interfaces" tree. I verified that the 6052E is working correctly. I also verified that the pxisys.ini file is in the WINNT directory. What is the problem?

I am first trying to install the SCXI chassis using the SCXI 1520 user manual. I put a PXI-6052E in the right-most PXI slot and the SCXI 1520 in a SCXI slot. On page 1-12 of the SCXI-1520 user manual, it instructs me to power up the chassis, right-click on MAX "devices and interfaces", choose the correct chassis, and click finish. The problem is, after I click finish, a window appears that forces me to choose a DAQ device. The SCXI chassis doesn't configure correctly because the wizard doesn't see the PXI-6052E.

AIM ARINC board not detected with MXIe in a PXI-1033 chassis

Hi,
I have a PXI-1033 chassis with NI PXI-6229 and AIM boards (ARINC 429 & AFDX) linked to a PC with MXIe.
Windows can't attribute enough ressources to this device (indicated in the devices manager) so I can't install drivers for my boards.
If I only put NI PXI-6229 in my chassis, all is OK.
If I only put AIM boards in my chassis, Windows doesn't boot.
I tried with a PXI-1036 chassis linked to my PC with MXI-4, all is running correctly (NI and AIM boards).
Is there anyone who detects a problem of compatibility between AIM boards and MXIe links, and what is the solution ?
Thanks for answers.
Matthieu

Mmonterrat,
Problems like this are quite often caused by the computer's BIOS. Is there a BIOS update for your PC, and have you tried a different computer?
You can get more information here: http://digital.ni.com/public.nsf/websearch/05B7131814A5DDA38625710F006BB098?OpenDocument
Robert

PXI-1033 power up causes PC to boot up

I have a PXI-1033 chassis connected to a Windows 7 PC via MXI-Express cable. Both the PC and PXI chassis are off. When I push the power button on the PXI chassis, the PC turns on. I cannot figure out the cause of this. Thanks.

habsfan,
This is expected behavior. The PXI-1033 attempts to wake the host PC when it's turned on as a convenience so you can power up the whole system with a single switch. The mechanism it uses is the PCIe WAKE# signal.
Is it a problem for you, or are you just suprised by it? I don't think there's a way to disable it on the PXI-1033, but there may be other ways. Many systems have an option to enable or disable waking the system from PCIe cards, so you could look through the BIOS options of your PC. Or, if you power on the chassis 4-5 seconds before connecting the MXI cable it shouldn't wake the PC.
- Robert

PXI-1033 Linux Support

Hi,
I have a setup with one PC connected to a USB-6009 and PXI-1033 chassis.
On windows both of the hardware work perfect.
Now I want to switch to Linux.
I installed
(1) NI-DAQmx Base 3.4 - SUSE, RedHat
(2) PXI Platform Services 2.6 - Linux - Beta
on a Scientific Linux 5.5
Everything went pretty well, no errors. I answered yes to all questions
Now, when I run lsdaq, only USB6009 is seen.
nipxi/nipxiconfig -l all shows nothing.
Is PXI-1033 supported on Linux ?

The PXI chassis is configured as the following
Slot 2,3 PXI-6255
Slot 4-6 PXI-6723
Connected to PC using PXIe-8361
nipxiconfig did not identify any card or chassis.
However, I believe the hardware connection is OK as I have the following lspci result
lspci
02:00.0 PCI bridge: PLX Technology, Inc. PEX 8505 5-lane, 5-port PCI Express Switch (rev aa)
03:03.0 PCI bridge: PLX Technology, Inc. PEX 8505 5-lane, 5-port PCI Express Switch (rev aa)
04:00.0 PCI bridge: Texas Instruments XIO2000(A)/XIO2200(A) PCI Express-to-PCI Bridge (rev 03)
05:0b.0 Class ff00: National Instruments Unknown device 70ff
05:0c.0 Class ff00: National Instruments Unknown device 70ff
05:0d.0 Class ff00: National Instruments Unknown device 70ff
05:0e.0 Class ff00: National Instruments Unknown device 71e1
05:0f.0 Class ff00: National Instruments Unknown device 71e1

Hello friends, my itunes has stopped working. and the problem report stated the following: Fault Module Name:     KERNELBASE.dll   Fault Module Version:     6.1.7601.17514.................. please can anybody help me?hello friends, my itunes has stopped w

Hello everybody> my itunes has stopped working and the problem report stated the following:
Problem signature:
Problem Event Name:    APPCRASH
Application Name:    iTunes.exe
Application Version:    10.5.3.3
Application Timestamp:    4f14cc3d
Fault Module Name:    KERNELBASE.dll
Fault Module Version:    6.1.7601.17514
Fault Module Timestamp:    4ce7b8f0
Exception Code:    80000003
Exception Offset:    0003381b
OS Version:    6.1.7601.2.1.0.256.1
Locale ID:    1033
Additional Information 1:    0a9e
Additional Information 2:    0a9e372d3b4ad19135b953a78882e789
Additional Information 3:    0a9e
Additional Information 4:    0a9e372d3b4ad19135b953a78882e789
can anybody help me?

Are you seeing a similar message when launching QuickTime Player?
What security software is installed on the computer? Have you tried testing in an admin account or after uninstalling tthe security software?
Use one of the following articles to guide you through removing iTunes and the related QuickTime files.
Removing and Reinstalling iTunes, QuickTime, and other software components for Windows XP
Removing and reinstalling iTunes, QuickTime, and other software components for Windows Vista or Windows 7

Itunes not workin and the problem displays - m signature:   Problem Event Name:     BEX   Application Name:     iTunes.exe   Application Version:     10.5.3.3   Application Timestamp:     4f14cc3d   Fault Module Name:     QuickTime.qts_unloaded   Fault Mo

i tunes not working and the problem its displaying is
m signature:
Problem Event Name:    BEX
Application Name:    iTunes.exe
Application Version:    10.5.3.3
Application Timestamp:    4f14cc3d
Fault Module Name:    QuickTime.qts_unloaded
Fault Module Version:    0.0.0.0
Fault Module Timestamp:    4cf45322
Exception Offset:    706e1040
Exception Code:    c0000005
Exception Data:    00000008
OS Version:    6.1.7601.2.1.0.256.1
Locale ID:    1033
Additional Information 1:    0a9e
Additional Information 2:    0a9e372d3b4ad19135b953a78882e789
Additional Information 3:    0a9e
Additional Information 4:    0a9e372d3b4ad19135b953a78882e789
Read our privacy statement online:
http://go.microsoft.com/fwlink/?linkid=104288&clcid=0x0409
If the online privacy statement is not available, please read our privacy statement offline:
C:\Windows\system32\en-US\erofflps.txt
please help.

im having this problem to ive uninstalled and installed but this still comes up!!
Problem signature:
Problem Event Name:    BEX
Application Name:    iTunes.exe
Application Version:    10.7.0.21
Application Timestamp:    504d85d9
Fault Module Name:    StackHash_0a9e
Fault Module Version:    0.0.0.0
Fault Module Timestamp:    00000000
Exception Offset:    00000000
Exception Code:    c0000005
Exception Data:    00000008
OS Version:    6.1.7601.2.1.0.768.3
Locale ID:    5129
Additional Information 1:    0a9e
Additional Information 2:    0a9e372d3b4ad19135b953a78882e789
Additional Information 3:    0a9e
Additional Information 4:    0a9e372d3b4ad19135b953a78882e789

Urgent: regarding ALV report display problem

hi,
There are 3 problems:-
1.) I had made a ALV report in which i have to display 'POSTING DATE' (iseg-budat) when we execute the report i.e. it should be displayed as PERIOD :- _______ to _______ on alv report ..
2.)the 2nd problem is dat when i use the ' wa_fieldcat-no_zero = 'X'. It eliminates all the leading zeros which are present which is okay when i it displays material no.. but the problem is dat it also deletes the other fields where the values are to be zeros.
i had used this FM:-
CALL FUNCTION 'CONVERSION_EXIT_ALPHA_OUTPUT'
EXPORTING
   INPUT = ITS1-MATNR
   IMPORTING
   OUTPUT = ITS1-MATNR.
so that only matnr field are to be 0's.
3.) I want to delete the rows which use to contain the values 0's as there are no calculations are performing as these are displayed .
ANYbody having solution of this problem ,plzzzz provide the soluion of it as it is most urgent to me and dat person will definately rewarded.
regards,
ric.s

hi kiran,
thanks for ur response. here is d code which i am using it and plzz help me to figure out where i have to make changes:-
REPORT ZTEST03.
TABLES: ISEG,MARA.
TYPE-POOLS : SLIS.
INTERNAL TABLE FOR INVENTORY STOCK *****************
DATA: BEGIN OF ITS1 OCCURS 0,
      MATNR LIKE ISEG-MATNR,
      MEINS LIKE ISEG-MEINS,
      MENGE LIKE ISEG-MENGE,
      WRTZL LIKE ISEG-WRTZL,
      BUCHM LIKE ISEG-BUCHM,
      WRTBM LIKE ISEG-WRTBM,
      WERKS LIKE ISEG-WERKS,
      BUDAT LIKE ISEG-BUDAT,
      MTART LIKE MARA-MTART,
      ITEMDESC LIKE MAKT-MAKTX,
      DIFFQTY LIKE ISEG-BUCHM,
      DIFFVALUE LIKE ISEG-WRTBM,
      END OF ITS1.
data: t_heading type slis_t_listheader.
SELECTION-SCREEN BEGIN OF BLOCK PAR1 WITH FRAME TITLE TEXT-001.
*********PARAMETERS*********
PARAMETERS : PLANT LIKE ISEG-WERKS OBLIGATORY.
*********SELECTION SCREEN OPTIONS*********
SELECT-OPTIONS : R_DATE FOR ISEG-BUDAT,
                 M_TYPE FOR MARA-MTART,
                 IT_M FOR MARA-MATNR.
*********DEFINING VARIABLES*********
SELECTION-SCREEN END OF BLOCK par1.
TOP-OF-PAGE.
     PERFORM PG_HEADER.
START-OF-SELECTION.
SELECT DISTINCT A~MATNR A~MEINS A~MENGE A~WRTZL A~BUCHM A~WRTBM A~WERKS A~BUDAT B~MTART
   FROM ISEG AS A INNER JOIN MARA AS B ON B~MATNR = A~MATNR
     INTO CORRESPONDING FIELDS OF TABLE ITS1 WHERE B~MATNR = A~MATNR AND B~MEINS = A~MEINS AND A~WERKS = PLANT AND A~BUDAT IN R_DATE AND B~MTART IN M_TYPE AND B~MATNR IN IT_M.
CALL FUNCTION 'CONVERSION_EXIT_ALPHA_OUTPUT'
EXPORTING
   INPUT = ITS1-MATNR
   IMPORTING
   OUTPUT = ITS1-MATNR.
SORT ITS1 BY MATNR.
DELETE ADJACENT DUPLICATES FROM ITS1 WHERE MENGE = 0 AND BUCHM = 0.
LOOP AT ITS1.
     ITS1-DIFFQTY = ITS1-MENGE - ITS1-BUCHM.
     ITS1-DIFFVALUE = ITS1-WRTZL - ITS1-WRTBM.
     SELECT SINGLE MAKTX FROM MAKT INTO ITS1-ITEMDESC WHERE MATNR = ITS1-MATNR.
     MODIFY ITS1.
ENDLOOP.
PERFORM PRN_SMSTOCK_ALV.
WRITING DATA FROM D TABLES**********
FORM PG_HEADER.
WRITE : 'PHYSICAL INVENTORY AUDIT REPORT             PLANT : ', PLANT.
ENDFORM.
*&      Form PRN_SMSTOCK_ALV
      text
--> p1        text
<-- p2        text
form PRN_SMSTOCK_ALV .
data: w_title   type lvc_title,
      w_repid   type syrepid,
      w_comm    type slis_formname,
      w_status type slis_formname,
      x_layout type slis_layout_alv,
      t_event    type slis_t_event,
      t_fieldcat type slis_t_fieldcat_alv,
      t_sort     type slis_t_sortinfo_alv.
refresh t_fieldcat.
refresh t_event.
refresh t_sort.
clear x_layout.
clear w_title.
perform set_fieldcat2 using:
1 'MTART'     'MTART'     'MARA' '15' space 'MATERIAL TYPE'        space space space space space space space space SPACE t_fieldcat 'L' 'C',
2 'MATNR'     'MATNR'     'MARA' '13' space 'MATERIAL NO. '        space space space space space space space space SPACE t_fieldcat 'R' 'C',
3 'ITEMDESC' 'MAKTX'     'MAKT' '25' space 'MATERIAL DESCRIPTION' space space space space space space space space SPACE t_fieldcat 'L' 'C',
4 'MEINS'     'MEINS'     'MARA' '5'   space 'UOM'                  space space space space space space space space SPACE t_fieldcat 'C' 'C',
5 'MENGE'     'MENGE'     'ISEG' '13' space 'ORG.INV.QTY'          space space space space space space space space SPACE t_fieldcat 'R' 'C',
6 'WRTZL'     'WRTZL'     'ISEG' '13' space 'ORG.INV.VALUE'        space space space space space space space space SPACE t_fieldcat 'R' 'C',
7 'BUCHM'     'BUCHM'     'ISEG' '13' space 'PHY.INV.QTY'          space space space space space space space space SPACE t_fieldcat 'R' 'C',
8 'WRTBM'     'WRTBM'     'ISEG' '13' space 'PHY.INV.VALUE'        space space space space space space space space SPACE t_fieldcat 'R' 'C',
9 'DIFFQTY'   'MENGE'     'ISEG' '13' space 'DIFF.INV.QTY'         space space space space space space space space SPACE t_fieldcat 'R' 'C',
10 'DIFFVALUE' 'WRTZL'     'ISEG' '13' space 'DIFF.INV.VALUE'       space space space space space space space space SPACE t_fieldcat SPACE 'P'.
x_layout-zebra = 'X'.
perform set_top_page_heading using t_heading t_event.
perform set_events using t_event.
w_status = ''.
w_repid = sy-repid.
w_comm   = 'USER_COMMAND'.
call function 'REUSE_ALV_GRID_DISPLAY'
    exporting
      i_callback_program       = w_repid
      it_fieldcat              = t_fieldcat
      i_Callback_top_of_page   = 'Top-of-page'
      is_layout                = x_layout
      it_sort                  = t_sort
      i_callback_pf_status_set = w_status
      i_callback_user_command = w_comm
      i_save                   = 'X'
      it_events                = t_event
      i_grid_title             = w_title
      tables
      t_outtab                 = ITS1
    exceptions
      program_error            = 1
      others                   = 2.
if sy-subrc <> 0.
    message id sy-msgid type sy-msgty number sy-msgno
            with sy-msgv1 sy-msgv2 sy-msgv3 sy-msgv4.
endif.
ENDFORM.
FORM set_fieldcat2 USING
      p_colpos p_fieldname p_ref_fieldname p_ref_tabname
      p_outputlen p_noout
      p_seltext_m p_seltext_l p_seltext_s p_reptext_ddic p_ddictxt
      p_hotspot p_showasicon p_checkbox p_edit
      p_dosum
      t_fieldcat TYPE slis_t_fieldcat_alv
      P_JUST
      P_FTYPE.
DATA: wa_fieldcat TYPE slis_fieldcat_alv.
CLEAR wa_fieldcat.
General settings
wa_fieldcat-fieldname = p_fieldname.
wa_fieldcat-no_zero = 'X'.
wa_fieldcat-col_pos = p_colpos.
wa_fieldcat-no_out = p_noout.
wa_fieldcat-hotspot = p_hotspot.
wa_fieldcat-checkbox = p_checkbox.
wa_fieldcat-icon = p_showasicon.
wa_fieldcat-do_sum = p_dosum.
Set output length.
IF NOT p_outputlen IS INITIAL.
    wa_fieldcat-outputlen = p_outputlen.
ENDIF.
Set text headers.
IF NOT p_seltext_m IS INITIAL.
    wa_fieldcat-seltext_m = p_seltext_m.
ENDIF.
IF NOT p_seltext_l IS INITIAL.
    wa_fieldcat-seltext_l = p_seltext_l.
ENDIF.
IF NOT p_seltext_s IS INITIAL.
    wa_fieldcat-seltext_s = p_seltext_s.
ENDIF.
IF NOT p_reptext_ddic IS INITIAL.
    wa_fieldcat-reptext_ddic = p_reptext_ddic.
ENDIF.
IF NOT p_ddictxt IS INITIAL.
    wa_fieldcat-ddictxt = p_ddictxt.
ENDIF.
IF NOT P_JUST IS INITIAL.
    WA_FIELDCAT-JUST = P_JUST.
ENDIF.
Set as editable or not.
IF NOT p_edit IS INITIAL.
    wa_fieldcat-input     = 'X'.
    wa_fieldcat-edit     = 'X'.
ENDIF.
APPEND wa_fieldcat TO t_fieldcat.
ENDFORM.                   "set_fieldcat2
======================== Subroutines called by ALV ================
*&      Form top_of_page
      Called on top_of_page ALV event.
      Prints the heading.
form top_of_page.
call function 'REUSE_ALV_COMMENTARY_WRITE'
     exporting
          it_list_commentary = t_heading.
ENDFORM.
form set_top_page_heading using t_heading type slis_t_listheader
                                t_events type slis_t_event.
data: x_heading type slis_listheader,
      x_event   type line of slis_t_event.
Report title
clear t_heading[].
clear x_heading.
x_heading-typ = 'H'.
x_heading-info = 'PHYSICAL INVENTORY AUDIT REPORT'.
append x_heading to t_heading.
Plant Name
clear x_heading.
x_heading-typ = 'S'.
x_heading-key = 'PLANT: '.
x_heading-info = its1-werks.
append x_heading to t_heading.
Posting Date
*clear x_heading.
x_heading-typ = 'S'.
x_heading-key = 'POSTING DATE: '.
x_heading-info = ITS1-BUDAT.
append x_heading to t_heading.
Control Date
clear x_heading.
x_heading-typ = 'S'.
x_heading-key = 'CONTROL No: '.
x_heading-info = its1-werks.
append x_heading to t_heading.
Control date
clear x_heading.
x_heading-typ = 'S'.
x_heading-key = 'CONTROL DATE: '.
x_heading-info = its1-werks.
append x_heading to t_heading.
User who is running the report
clear x_heading.
x_heading-typ = 'S'.
x_heading-key = 'User: '.
x_heading-info = sy-uname.
append x_heading to t_heading.
Date of execution
clear x_heading.
x_heading-typ = 'S'.
x_heading-key = 'Date: '.
write sy-datum to x_heading-info.
append x_heading to t_heading.
Time of execution
clear x_heading.
x_heading-typ = 'S'.
x_heading-key = 'Time: '.
write sy-uzeit to x_heading-info.
append x_heading to t_heading.
Top of page event
x_event-name = slis_ev_top_of_page.
x_event-form = 'TOP_OF_PAGE'.
append x_event to t_events.
endform.
form set_events using t_events type slis_t_event.
data: x_event   type line of slis_t_event.
endform.
plzzz help me out as it is most urgent to me.
regards,
ric.s

URGENT: PXI-1033 and DAQmx problem

Similar Messages

Maybe you are looking for