URGENT! why msi 865pe(6728) doesnt support intel celleron 1.7 cpu?

why msi 865pe(6728) neo2-s doesn't support intel celleron 1.7 cpu?
all other 865 chipsets support intel celleron cpus but msi mobos not ! why? or is there any way that i can run mobo with celleron 1.7 cpu?

yes, we have tried. yesterday i bought a new mobo for my friend. he has celleron 1.7, when we start the system it does nothing also the d-bracket colors are
OO
OO
O:red that means "the d-led will hang here if the processor is damaged or not installed properly! "
the same procesor is workings with no problem on his old board!
is there any solution that you can suggest? as i sad all other 865 chipsets support celleron cpus! :(

Similar Messages

MSI 865PE Neo 3-F + Intel P4 640

Hello,
I have a problem with a MSI 865PE Neo 3-F motherboard combined with an Intel 640 cpu.
I cannot install Windows XP SP2, everytime at 35 minutes remaining, the computer resets itself.
First I had bios v5.0, and couldn't flash to v5.2, after using a Intel 520 cpu I could flash to v5.2, but the problem remains.
Tried several ram-modules, hdd, vga-cards, psu's, ...
Anyone know if there is a solution for this ? Maybe a new bios-version or beta-bios ?
Thanks,
Jan

Two things you could test;
Run memtest86 for any mem.errors ( you can do this by creatings a DOS disc and boot from floppy )
http://www.memtest.org/#downiso
Not sure about the 410w chieftec - Is that a ATX2.0 PSU with 24pin connector ? ( 12v1 =15amp + 12v2=18 amps)
Do you use a 24-20 pin adapter ?
If I´m correct, your MoBo still got the 20-pin MoBo + 4-pin cpu powerconnector, and too be sure about the power issue, I would have prefered a PSU with some 450w and a singel 12v line with minimum 22 amps on the 12v line. The newer P4/ Prescott cpu´s needs a lot of 12v power.- Be sure that both 20pin and 4pin are firmly in place on the MoBo.
Most highly recommended PSU´s are Enermax, Antec, Tagan, OCZ, but there are others as well as long as you avoid the cheap ones -
PS - about mem.voltage it would be 2.7v not 1.7v as you wrote, but assume this was only a typingfault.
775 socket cpu installation
http://www.msi.com.tw/html/service/techexpress/mainboard/7028/page2.htm

Change Vcore on Prescott MSI 865PE 6728 Neo2 is possible !!!

hello
a vcore change on the MSI 6728 Neo-2 IS possible, you just have to use the bios version 1.9 !!! but you dont have the advance of the bugs fixed in actual version.
it looks like MSI only "HIDE" the vcore settings. the tool "AMIBCP75" dosent work on the new AMI bios. does anyone have a new AMIBCP for 8 series bios ???
i hope that msi change this very very soon, cause without a vcore change for prescott this board is NO hardcore overclocking board ! very bad thing !
looks like epox also stops vcore change on prescott in new bios
(sorrys for bad english :-) )
psycho

psycho303, You might want to read this before you change your V Core
http://www.hardocp.com/article.html?art=NTg5
Quote
I discussed the Vcore change question with the board designer over last weekend. Base on my understanding, the reason we didn't offer that when Prescott is populated was because a new Intel VID design on Prescott: "Dynamic VID" (VID becomes variable on different stages). According to the board designer, if M/B (BIOS) overwrite the Vcore, Dynamic VID will become invalid which might damage the CPU (Prescott Core) when power stage changed.
It is my understanding that bios version 1.9 does not support this VID and you could end up with a "dead" chip.
After updating my bios I can watch the Vcore throttle up and down as the load on the CPU changes . At an idle it is around 1.36 and under a load it can go as high as 1.48. If you bump up the starting point of the Vcore it could throttle up higher than the chip can handle
I am able to get 3.59 out of my chip on the stock vcore and can go much higher but I am using "Air" and have to watch the heat.
Dave

Intel Core2 Quad Q9550 CPU, 2.83GHz

Hi!
I dream of buying the new processor called Intel Core2 Quad Q9550 CPU, 2.83GHz.
Is it to suit my motherboard - Marketing Name: P35 Neo2-FR/FIR; MSI Model: MS-7345?
Intel Core2 Quad Q9550 CPU, 2.83GHz has 45nm. My motherboard can receive 45nm or 65nm only?
If so, do I need to upgrade the BIOS?
If there is no upgrade from the BIOS. It means that I can only put into Intel Core2 Quad Q9550 CPU, 2.83GHz to the motherboard.
Regards Lillemester :-)

Yes it can, check CPU Support page:
http://global.msi.com.tw/index.php?func=prodcpusupport&prod_no=1261&maincat_no=1#menu

Why does MSI P4N have no support for Intel Preslor and Asus Nforce 4 does??

Well as you've probably guessed it im new to the forums (howdy all ). I currently own a MSI P4N diamond motherboard and quite frankly i most dissapointed with what has been called (by too many reviewers) a great board.
First off i see very little changes taking place with each bios update, of which does not seem to happen regularly at all. (lets face it no board is perfect especially the Nforce 4 range from MSI for Intel CPU's).
Secondly overclocking a Pentium D 830, which i may add should be capable of overclocking very well on an Intel Nforce board, can barley reach 3.4 Ghz (i know its mobo issue as the CPU is water cooled and overclocks to way beyond 3.7 on an 955X board).
Thirdly the North bridge fan was poorly stuck on my motherboard in that on installing my motherboard into my case it popped off like the lid of a pringles tub by a slight movement of my hand .
And last but least... why does the MSI P4N diamond motherboard not support Intels latest 65nm CPU's when ASUS's and Gigabyte's Nforce 4 motherboards work well with the Pentium D and the 65nm range of Intel CPU's. Upon also reading about the next gen of Intel CPU's the Conroe, the 975X motherboards will support the future CPU via a bios update and it has been said that the same is likely to happen for the Nforce 4 range... however once again due to the lack of support for the MSI P4N diamond by MSI i believe all of us owners of this pathetic (an over statement really but its going to be that way if MSI keeps this up) over hyped motherboard will get a simple NO in the CPU support table for the next gen range of CPU's.

Where did you get the information regarding the MSI P4N diamond's release date?
Are you in the United Kingdom? As it was released at the same time as the other Nforce 4 boards here (i was on the edge of my seat waiting for the Nforce boards to be released on overclockers.co.uk for sale) In the end though i bought my mothreboard in October, which is a good few weeks after release.
Is there any kind of SLI 32 on MSI's plans? this is what worries me as they have made a move in the 975X department but have not made any further developmentes in the Nforce range for Intel, which to the average joe kind of indicates loss of intrest in this field from the company.
I am overall pleased with my motherboard, when using a single core CPU, as overclocking was a sheer joy, but as soon as the dual core CPU went in the mothreboard behaves like a drunk man coming from a pub. I am aware that the Nforce 4 chipsets struggle with the dual core CPU's but surely Nvidia were informed by Intel about the dual core CPU's being released in the future.

[Please Help]Does MSI Axis 945G support intel core2 duo T7600?

I have an idle CPU intel core2 duo T7600,so I am considering buying an AXIS 945GM to let it work.
I have a question ,does MSI Axis 945G support intel core2 duo T7600?
I checked the CPU suppot list on MSI website,I just found it suppots upto T7400.
Can I flash the new BIOS v1.23 to support T7600?
thank you!

According to the CPU Support List, this won't help. The best thing to do would be to contact MSI Technical Support. Maybe they can give you a more definate answer:
http://ocss.msi.com.tw/

What is the max supported CPU for MSI 865PE-NEO2-LS?

Can someone please tell me what is the max supported CPU speed for the MSI 865PE-NEO2-LS? I have a P4 2.8@800Mhz, but was told that with a BIOS upgrade this motherboard can achieve up to 3.2? Is that right, or can it support higher speeds such as the 3.4+
Thank you!

Hello,
http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_cpu_support_detail.php?UID=433&kind=1
I think A6728IMS.210 means BIOS 2.1 so it may already work with the 3.2Ghz CPU.
http://www.msi.com.tw/program/support/bios/bos/spt_bos_detail.php?UID=433&kind=1

I used to be able to airplay from Ipad1 to AppleTV, but now it doesnt support it. Why not?

When I first got Apple TV about 2 years ago, I was able to airplay from my Ipad 1. It wasnt called mirroring back then, but it worked the same. Now it doesnt support that. Whats up with that? Is there a way to work around that?

Verizon is not doing that it is the mail that is doing that.
Check your device settings for email and read the owners manual as to how to set up mail to download. How you want it, leave on server, etc.
Good Luck

Unable to detect Hyper Threading of CPU SL6WE 3.2 in MSI-865PE Neo2

Hi! I am new to this forum and need some help. I have just installed a Intel Pentium 4 3.2GHz Northwood SL6WE 478 800MHz/512k . I bought this on e-bay and understand that this cpu supports hyper threading. I have enabled hyper threading in the bios, but only see one cpu in Widows System Properties and only one cpu in Windows Task Manager. I had a 2.6 cpu installed previously, no hyper threading. My motherboard is an MSI-865PE Neo2 version 1.1, 2GB Ram ( 4x512 ?), Thermaltke TR2-430W power supply, Freezer 4 Arctic Cooler, Nvidia GeForce 6600, LG DVD RAM burner, 16x DVD ROM, WD 250 gig and an Hitachi 80 gig hard drive. I also used Arctic Silver 5 thermal paste (after using Arcticclean and Surface Purifier). Have I missed somethig? Would appreciate help in solving why I have no hyper threading.

200 7-3-3-2.5 Ultra Turbo and 212 5-3-3-2.5 Ultra Turbo is a
no boot. Thinks ultra-turbo tries to set mem timings to
2-2-2-5 below 218FSB and my memory can't do that.
Turbo boots ok. Normal setting disabled PAT.
200 2.5-3-3-7 Turbo PAT on 4.6GB/s
200 2.5-3-3-7 Normal PAT off 4.2GB/s
212 2.5-3-3-5 Turbo PAT on 4.8GB/s
212 2.5-3-3-5 Normal Pat off 4.5GB/s
Also tried 250 1:1, not prime95 stable
250 2.5-3-3-7 Ultra-turbo 6GB/s
I think pat is disabled above 218FSB on
1:1 and 5:4 setting, but not on 4:5 setting.
You should get close to or above 6GB/s at
1:1 250 3-3-3-5 bios overclocking.
Maybe something is running in the background
stealing cpu power or something?
Well, you have to test some more, maybe a
fresh windows setup will help?

MSI 865PE-LS query etc

I received a later bios today not sure if I should try it
Bios Vs A6728IMS.162
I am still stuck on memory settings etc + best bios config for my
MSI 865PE LS Neo2 Bios Vs 1.52
to make the MB run stable there are OClock settings slow,fast,turbo,ultra turbo if I try to increase any of these the pc wont start not sure why the bios has these options if they dont work
still require best config for this
exact setup specs please for the bios
thanks
tony
IntelP4 2.8ghz 800mhzFSB
WinXP Pro - SR-1 + updates
MSI 865PE LS Neo2 Bios Vs 1.52
2x Kingston KVR400X64C25/512
Albatron Ti 4800SE 128
WD 120gb
Thermaltake Xaser3 (blue)case
420w PSU

2.4c @ 3.3GHZ / 1081 FSB
KINGSTON HYPERX DDR433 CAS2
OK. i have the 865PE Neo2 LS.
After a long of reseach, i can say that this mobo rocks!!!, but u must know exactly what u r doing....
I strongly suggest to have BIOS V1.5 !! (I flashed from 1.3, in which there was no
support for Hyperthreading..)
Follow this steps exactly (if u have at least DDR433, if not reduce fsb to match your memory specs)
1. Disable Dynamic Overclocking (DOT)
2. Set DDR frequency to 333MHz to obtain the 5/4 CPU/Memory FSB ratio
3. Set DRAM timings to auto (SPD) if u dont know the correct specs. If u do disable SPD and set them.
4. Note : MAT is automaticaly disabled in 4:5 mode (You can set Performance = Slow, but even in Ultra turbo
this is the same-not actually wotking)
5. Increase the Vcore from 1.5225 to 1.600 volts (safe up to 1.8)
6. Set CPU FSB=271MHz (this runs the DDR at 433 (216.5 x 2), go lower if your DDR is less than 433)
7. Set AGP/PCI ratio fixed to 68/34. If you go higher u may have problems with
sound and VGA card.
Save and ReBoot !!!
Note2:
DOT is crap (It works if u dont overclock at BIOS and the max FSB increase at General level is 10%)
MAT is also crap compared to a CPU FSB of 271 and DDR @ 433. (MAT offers 5% max improvement in memory bandwidth)
which is nothing compared to the above FSBs.
Note3 : NB temp is invalid..ignore it
Go see for your self my benchmarking results at :
http://stefanos9.topcities.com/Downloads.html
(Download pc1 and pc2 ppt)
IF you reach to 5400 in memory bandwidth, then the bottleneck is eliminated. From 5400 and above is the same.
Check memory bandwidth benchmarks, they are above the 875PE with intel's MAT/PAT !!!!
Stef

MSI 865PE NEO2-V showing wrong RAM timings

Hi
I have a MSI 865PE NEO2-V motherboard with Corsair TWINX2048-3200C2 DDR-DIMM 2048MB Kit w/two matched CMX1024-3200C2 DIMMs now and try to put the timings of the RAM to 2-3-3-6 in the bios.
According to http://www.corsairmemory.com/corsair...h_results.html it should work ok...but its not.
When i check the timings with CPU-Z it shows 3-4-4-8 instead.
The SPD is 3-3-3-8.
I have checked so they are in Dual channel and i have put the RAM voltage to 2.75V after i tried with the default voltage, but to no avail.
To be extra certain i ran Everest Ultimate and it showed the exact timings.
The RAM run fine with StressPrime and Prime95 but i get bad results in SiSoft Sandras RAM benchmarks.
What is going on????

Hi
Yeah, it get slow results.
I have a Intel Prescott 3.2Ghz with FSB800.
I see now that the link uses Java script, its in Corsairs search engine on their site.
Their recomendations for the set of RAM i have is: TWINX2048-3200C2 / DDR-400 (XMS-3200C2) / 2-3-3-6 .
I have tried to set the timings as you said but it still runs at 3-4-4-8 whatever i set it at.
I have it running at 2-3-3-6 on another motherboard so i think it must be some settings in the BIOS that i set wrong on this one, but i cant figure it out.
Could it be that somethings wrong with the Performance Mode (MAT) settings?
I tried it on and off, I have also reseted the BIOS to default and even removed the CMOS battery for a while.
I paste all the info from the Corsair site here:
Facts about the TWINX2048-3200C2
The TWINX2048-3200C2 is a pair of 1024 MByte DDR SDRAM DIMMs designed for extreme speed are some of the fastest 1 GByte modules available. TWINX matched memory pairs are specifically designed for motherboards using chipsets with dual memory channels. This part delivers outstanding performance at high clock speeds. It has been tested extensively in a variety of motherboards commonly used in gaming rigs. This memory has been verified to operate at 200 MHz (DDR400) at aggressive latencies of 2-3-3-6. This module is also available as a single module. This module is available as a single module or a pair of dual-channel tested modules, in both black and platinum heat spreaders.
Facts about this Chipset
The 865PE chipset is a great choice for users who require a complete range of support for the Pentium 4 processor, with high-bandwidth DDR memory and discrete graphics cards. Engineered to optimize Dual-Channel DDR SDRAM memory performance, the 865PE chipset features an 800-MHz system bus, support for the latest AGP8X graphics cards, and high-bandwidth DDR400/333/266 SDRAM memory technology.
Facts about this Motherboard
This 865PE Neo2-V MSI board is flexible and highly scalable solution that meets a broad range of demanding computing needs. The 865PE chipset offers high-bandwidth interfaces such as dual-channel DDR 400 main memory, coupled with an 800 MHz system bus, AGP8X graphics interface, dual independent Serial ATA ports and Hi-Speed USB 2.0 connectivity to ensure the performance you expect.
http://www.corsairmemory.com/corsair/products/specs/twinx2048-3200c2.pdf

Help With 865Pe 6728 neo2-Platinum

In Bios mb the changes of timings for memory not setup manual! All my changes in manual is ignored and take from SPD of memory.
When i wanna overclock CPU, set the memory clock 333, system bus - 240 (result for memory 400), but timings is for 333 state (Cl2.5)
Timings for my mem - 333-2.5-3-3-6, 400-3-3-3-8.
In first run after overclock - is test state of SPD and MEM, and itself choose state.
After change CL2.5 to CL3 mainboard is reset overclock.
PCI/AGP-66/33, MAT is off, DOT is off.
And when i choose manual 3-3-3-8-8 for 400mem without overclock - the mem real work in 3-4-4-8-8.
Sory for my bad English ))
My config now.
Intel Pentium 4
Prescott
stepping C0
CPUID Intel(R) Pentium(R) 4 CPU 3.00GHz
CPUID 00000F33h
3374.9 MHz (исходное: 3000 MHz, overclock: 12%)
15.0x
CPU FSB 225.0 MHz (исходное: 200 MHz, overclock: 12%)
225.0 MHz
DRAM:FSB 1:1
L2 1 Mb (On-Die, ECC, ATC, Full-Speed)
ID 63-3A01-001169-00101111-040201-I865G$1I865XXX_A6728IMS V3.A 092904
MSI 865PE Neo2-PS (MS-6728 v2.0) (5 PCI, 1 AGP, 4 DDR DIMM, Audio)
Intel Springdale i865PE
3-4-4-8 (CL-RCD-RP-RAS)
DIMM2: Samsung M3 68L6423ETM-CCC 512 Мб PC3200 DDR SDRAM (3.0-3-3-8 @ 200 МГц) (2.5-3-3-7 @ 166 МГц)
DIMM4: Samsung M3 68L6423ETM-CCC 512 Мб PC3200 DDR SDRAM (3.0-3-3-8 @ 200 МГц) (2.5-3-3-7 @ 166 МГц)
BIOS:
BIOS 09/29/04
DMI BIOS V3.A
Sapphire Radeon X700
RV410 (AGP 8x 1002 / 5E4D, Rev 00)
398 МГц (исходное: 400 MHz)
250 МГц (исходное: 250 MHz)
mb 31 °C (88 °F)
CPU 43 °C (109 °F)
GPU 50 °C (122 °F)
CPU 1.36 V
+3.3 V 3.31 V
+5 V 4.92 V
+12 V 12.54 V
+5 V res. 5.20 V
VBAT 3.04 V
FSB:
Intel NetBurst
64 бит
225 МГц (QDR)
900 МГц
Dual DDR SDRAM
128 бит
Intel Hub Interface
8 bit
75 Mhz (QDR)
300 Mhz
--------[ SPD ]---------------------------------------------------------------------------------------------------------
[ DIMM2: Samsung M3 68L6423ETM-CCC ]
Samsung M3 68L6423ETM-CCC
SN-060D2B32h (841682182)
512 Мб (2 ranks, 4 banks)
Unbuffered
DDR SDRAM
PC3200 (200 МГц)
64 bit
SSTL 2.5
(7.8 us), Self-Refresh
CAS Latency (CL) 3T
RAS To CAS Delay (tRCD) 4T
RAS Precharge (tRP) 4T
RAS Active Time (tRAS) 8T
Refresh Period (tREF) 7.8 us
Sapphire Radeon X700
128 Мб
1x, 2x, 4x, 8x
AGP 8x
Fast-Write Side Band Addressing

When your FSB is at 240Mhz, you have to set your DDR to "333mhz", so that the effective speed on your DDR is 400Mhz. You need to know that at 400MHz actual speed, achieving CL2.5 is not practical anymore. In fact your DDR is not rated CL2.5 at 400Mhz, but 400-3-3-3-8. So you can't set to CL2.5.

ATA HD for MSI 865PE Neo2-PS

I have this MB: MSI 865PE Neo2-PS (MS-6728 v2.0) and now I have both S-ATA full: one place HD and second place DVD burner.
I ordered now a new HD S-ATA and find out, that I have only this 2 ports for S-ATA
What would you recommend me - send back this new HD or exist any possibility how to connect this HD. I think this is a stupid question sorry.
I mean which HD would you recommend me if I can not use SATA HD?
Thank you

http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_detail.php?UID=528 this your board?
it supports 4 ata devices and 2 sata devices
look here https://forum-en.msi.com/index.php?topic=25959.0

Which MSI desktop board for new INTEL 1270.v3 build

Gents:
Intend replacing faithful legacy AMD965 system with an upgraded version of last years build:
INTEL 1240.v2
MSI Z77a.gd55 BIOS 1.2
NV 660 + 27" Auria
2x 1T HDD + 24-Gig Crucial ram
Running Ubuntu 14.04LTS .. which system supports both simulation & Apache OO software. This newer build listed above has performed flawlessly W/O brickworthy BIOS update.
I have limited finance, non-gamr and am VERY risk adverse. I intend the new build to run an INTEL 1270.v3 CPU. I trust MSI products, but cannot find reference/review to a desktop MSI motherboard to support this CPU and support it OOTB! Any clue appreciated.

I have never understood why BIOS chips aren't all pop-in/pop-out replaceable. Then a screwdriver and $30 check to BADFLASH would update the BIOS with the threat of bricking a system that might take weeks/months to reconstruct. That's just panding to DELL/HP/LENOVA/MS & a bad attitude from the mobo manufactures.
I will take your advise and look for recently manufactured boards, tho getting a serial number from NEWEGG or TIGER DIRECT would be like getting a Lords-prayer from Beelzebub!
Quote from: XFM on 04-November-14, 14:34:22
I can't recommend any particular MB for you but can just say do some research on MSI website for Z87/97 MBs for BIOS vs CPU support. Also keep in mind that recently manufactured MBs will have the later BIOS on them from the factory. You can determine if the MB you decide on has a later BIOS from the serial number if the store you buy it from will provide you the S/N (from date code in S/N) when purchased. Flashing the BIOS if needed isn't quite as bad as it might seem if you ask for help on this forum before attempting to do it. There's a right way and wrong way to do it and using Live Update is by far is the worst way, instant expensive paperweight is the usual result by using Live Update.

MSI 865PE-LS Neo2 Help and Info

Hi
I bought a MSI 865PE-LS Neo2
the motherboard is running Intel 2.8 800mhzFSB cpu
I would like to know what would be the best /fastest memory to run on this motherboard
I need to know why the bios performance setting revert to slow wont run the fast,turbo or ultra turbo settings also no sign of PAT/DOT
I would like to know the current/best bios settings to run the memory/cpu Kingston KVR400X64C25/512
Intel P4 2.8ghz 800FSB
Kingston KVR400X64C25/512 512MB 400Mhz PC3200 DDR Non ECC DIM
Albatron 4800SE
WD 120gb
Audigy2

Hi guys
thanks all for the input
still require best config for this
I have just been email bios VS A6728IMS.161 not sure if I should try it ? ?
exact setup specs please
thanks
tony
IntelP4 2.8ghz 800mhzFSB
WinXP Pro - SR-1 + updates
MSI 865PE LS Neo2 Bios Vs 1.52
2x Kingston KVR400X64C25/512
Albatron Ti 4800SE 128
WD 120gb
Thermaltake Xaser3 (blue)case
420w PSU

URGENT! why msi 865pe(6728) doesnt support intel celleron 1.7 cpu?

Similar Messages

Maybe you are looking for