USB 2.0 not functioning properly after upgrading to 3.10.3-1 kernel

After upgrading to the 3.10.3-1 kernel USB 2.0 is not working anymore on my ASrock ION330 nettop.
I just did a system upgrade (including a kernel upgrade to 3.10.5-1), but the problem remains...
Here's the relevant messages that I extracted with journalctl -b
Aug 07 09:59:11 alcyone kernel: ACPI: bus type USB registered
Aug 07 09:59:11 alcyone kernel: usbcore: registered new interface driver usbfs
Aug 07 09:59:11 alcyone kernel: usbcore: registered new interface driver hub
Aug 07 09:59:11 alcyone kernel: usbcore: registered new device driver usb
Aug 07 09:59:11 alcyone kernel: ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Aug 07 09:59:11 alcyone kernel: ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
Aug 07 09:59:11 alcyone kernel: ehci-pci: EHCI PCI platform driver
Aug 07 09:59:11 alcyone kernel: ohci_hcd 0000:00:04.0: setting latency timer to 64
Aug 07 09:59:11 alcyone kernel: ohci_hcd 0000:00:04.0: OHCI Host Controller
Aug 07 09:59:11 alcyone kernel: ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 1
Aug 07 09:59:11 alcyone kernel: ohci_hcd 0000:00:04.0: irq 16, io mem 0xfae7f000
Aug 07 09:59:11 alcyone kernel: hub 1-0:1.0: USB hub found
Aug 07 09:59:11 alcyone kernel: hub 1-0:1.0: 6 ports detected
Aug 07 09:59:11 alcyone kernel: ehci-pci 0000:00:04.1: setting latency timer to 64
Aug 07 09:59:11 alcyone kernel: ehci-pci 0000:00:04.1: EHCI Host Controller
Aug 07 09:59:11 alcyone kernel: ehci-pci 0000:00:04.1: new USB bus registered, assigned bus number 2
Aug 07 09:59:11 alcyone kernel: ehci-pci 0000:00:04.1: debug port 1
Aug 07 09:59:11 alcyone kernel: ehci-pci 0000:00:04.1: cache line size of 64 is not supported
Aug 07 09:59:11 alcyone kernel: ehci-pci 0000:00:04.1: irq 18, io mem 0xfae7ec00
Aug 07 09:59:11 alcyone kernel: ehci-pci 0000:00:04.1: USB 2.0 started, EHCI 1.00
Aug 07 09:59:11 alcyone kernel: hub 2-0:1.0: USB hub found
Aug 07 09:59:11 alcyone kernel: hub 2-0:1.0: 6 ports detected
Aug 07 09:59:11 alcyone kernel: hub 1-0:1.0: USB hub found
Aug 07 09:59:11 alcyone kernel: hub 1-0:1.0: 6 ports detected
Aug 07 09:59:11 alcyone kernel: usb 2-2: new high-speed USB device number 3 using ehci-pci
Aug 07 09:59:11 alcyone kernel: usb 2-2: device descriptor read/64, error -71
Aug 07 09:59:11 alcyone kernel: usb 2-2: device descriptor read/64, error -71
Aug 07 09:59:11 alcyone kernel: usb 2-2: new high-speed USB device number 4 using ehci-pci
Aug 07 09:59:11 alcyone kernel: usb 2-2: device descriptor read/64, error -71
Aug 07 09:59:11 alcyone kernel: usb 2-2: device descriptor read/64, error -71
Aug 07 09:59:11 alcyone kernel: usb 2-2: new high-speed USB device number 5 using ehci-pci
Aug 07 09:59:11 alcyone kernel: usb 2-2: device not accepting address 5, error -71
Aug 07 09:59:11 alcyone kernel: usb 2-2: new high-speed USB device number 6 using ehci-pci
Aug 07 09:59:11 alcyone kernel: usb 2-2: device not accepting address 6, error -71
Aug 07 09:59:11 alcyone kernel: hub 2-0:1.0: unable to enumerate USB device on port 2
Aug 07 09:59:11 alcyone kernel: usb 2-3: new high-speed USB device number 7 using ehci-pci
Aug 07 09:59:11 alcyone kernel: usb 2-3: device descriptor read/64, error -71
Aug 07 09:59:11 alcyone kernel: usb 2-3: device descriptor read/64, error -71
Aug 07 09:59:11 alcyone kernel: usb 2-3: new high-speed USB device number 8 using ehci-pci
Aug 07 09:59:11 alcyone kernel: usb 2-3: device descriptor read/64, error -71
Aug 07 09:59:11 alcyone kernel: usb 2-3: device descriptor read/64, error -71
Aug 07 09:59:11 alcyone kernel: usb 2-3: new high-speed USB device number 9 using ehci-pci
Aug 07 09:59:11 alcyone kernel: usb 2-3: device not accepting address 9, error -71
Aug 07 09:59:11 alcyone kernel: usb 2-3: new high-speed USB device number 10 using ehci-pci
Aug 07 09:59:11 alcyone kernel: usb 2-3: device not accepting address 10, error -71
Aug 07 09:59:11 alcyone kernel: hub 2-0:1.0: unable to enumerate USB device on port 3
Aug 07 09:59:11 alcyone kernel: usb 2-5: new high-speed USB device number 12 using ehci-pci
Aug 07 09:59:11 alcyone kernel: usb 2-5: device descriptor read/64, error -71
Aug 07 09:59:11 alcyone kernel: usb 2-5: device descriptor read/64, error -71
Aug 07 09:59:12 alcyone kernel: usb 2-5: new high-speed USB device number 13 using ehci-pci
Aug 07 09:59:12 alcyone kernel: usb 2-5: device descriptor read/64, error -71
Aug 07 09:59:12 alcyone kernel: usb 2-5: device descriptor read/64, error -71
Aug 07 09:59:12 alcyone kernel: usb 2-5: new high-speed USB device number 14 using ehci-pci
Aug 07 09:59:13 alcyone kernel: usb 2-5: device not accepting address 14, error -71
Aug 07 09:59:13 alcyone kernel: usb 2-5: device not accepting address 15, error -71
Aug 07 09:59:13 alcyone kernel: hub 2-0:1.0: unable to enumerate USB device on port 5
Aug 07 09:59:13 alcyone systemd[1]: Found device MCP79 Ethernet.
Aug 07 09:59:14 alcyone kernel: usb 1-1: new low-speed USB device number 2 using ohci_hcd
Aug 07 09:59:14 alcyone kernel: usb 1-4: new low-speed USB device number 3 using ohci_hcd
I'm glad that keyboard and mouse are working properly under USB 1.0, but neither my usb-parport printer nor my USB external hard drive are recognised any more :-(
Any ideas how to solve this?? (I'd prefer not to downgrade the kernel)
Last edited by zilverling (2013-08-07 14:28:36)

I've discovered it's not that USB 2.0 is not working. 3 out of 6 usb ports/busses seem to work properly. The other three seem totally dead. Obviously this was not the case under kernel 3.9.9-1. Downgrading to kernel 3.10.2 made no difference.
In practical terms this means that I can use my printer and access my external drive if I use the right port/bus. And I could probably work around the problem by plugging a USB hub in one of the working ports. But I would be happy to get rid of the error messages and have all 6 usb busses working as they did before...

Similar Messages

Wifi is not working properly after upgrading 7.1.1 onmy i4s

Dear Apple
i realy appriciate on your work ..right now i am suffreing from a problem that one i mentioned in subject .sometime my wifi is working good and sometime it shos dead to me ..but now its not working well after upgrading my phone on 7.1.1....
its my humble request please find a solution and provide me as soon as possble..
my totally work on wifi .
and sometime it goes hang in setting when i come on setting folder and clicked on wifi its get hang and also showing wifi is not availabe..please provide me best solution
Thanx & Regards
Sam
+91-92555-04628

settings - general - reset - reset network settings.

Plug and play speakers not working properly after upgrading to Windows 8.1

After upgrading to Windows 8.1, my plug and play speakers do not work properly. I have uninstalled and reinstalled them, and restarted. When I try to play music, nothing comes out. If I turn them off and back on, music will play for approximately 30 seconds, only from one speaker, then it turns off and fades to no sound. They worked fine until I upgraded to Windows 8.1. The manufacturer has not been able to successfully assist me. Has anyone else reported a similar issue after upgrading OS software? Any suggestions? These are fairly new speakers, less than 2 years old, and not used very much. I do have them installed via a K-V switch, and all other devices linked to the K-V switch are functioning properly (monitor and wireless keyboard). Any suggestions would be greatly appreciated.

@sisboldt ,
Hello and thank you for posting on the HP support forums.
So that I can better help you with your sound issue. Please post back with your full model and product number. Use this link to help you find the information.
HP Notebook PCs - How Do I Find My Model Number or Product Number?
Here is another link you may find useful. Please give it a read before posting back with your system information.
Advice for asking the "Very Best Question"
Thank you again for posting and have a great day.
Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
D5GR
I work on behalf of HP

2008 Macbook pro left click not working properly after upgrading to 10.6.8

I have a 2008 Macbook pro and a few months ago after upgrading to 10.6.8 my left click has been wonky.
Using the trackpad the left click eventually gets "stuck" or stops responding and I have to push it multiple times before it does anything. I have tried plugging in a mouse, but when I do so the mouse also behaves the same way. The only way I seem to be able to get the clicking to work properly is to restart the computer with the mouse attached.
I have seen threads about trackpads being messed up by swollen batteries, but my battery is brand new and looks fine, and the clicking problem extends to an external mouse, so I believe it is something with the preferences.
I tried deleting com.apple.driver.AppleBluetoothMultitouchTrackpad.plist and restarting and the problem seemed to be fixed, but then after about a half hour it returned.
Having to keep a mouse plugged into my macbook is driving me crazy, anyone know a solution?

I started having the same issue after update. I'm on a MacBookpro running 10.7.2
ICalled apple and they did a remove battery reboot, a reload lion and a option/command/R/P reboot on startup and then the computer started working. Two days later problem was back. I then did a reboot and the computer was back to working. Today the computer worked fine tell it went to sleep. I had to do a hard reboot to get the Mac up and running and now no left click. Please help. I can not use the Mac with the trackpad, a mouse, a Bluetooth mouse, or a digital pad. All so signs of left mouse click not working. One other item when you go to pick your user at startup the left mouse click works. Help!

ESS is not working properly after upgrade from 4.7 to ECC6.0

ESS Scenario in 4.7
4.7 Scenario:
The IMG configuration u201CWork and Life Eventsu201D is done to map them with the PZM3 service (Home Page) to get them as different folders/links on the home page as given below:
List of Services used to set up ESS:
Sl.No     Functionality     Service/EWT/URL Name     Standard/ Customized     Type
1     Home Page     PZM3                                          Standard                 Service
2     Inbox                     BWSP                                          Standard                 Service
3     Calendar                     BWCA                                          Standard                 Service
4     Whou2019s Who     PZ01                                          Standard                 Service
5     CPF Display     http://192.168.0.2:7070/omcpf             NA                                  URL
6     Payslip Display     ZPAYSLIP_USER                          Customized                Service
7     Section 80C     PZ88                                          Standard                EWT
8     Section 80                     PZ80                                          Standard                EWT
9     Form 16                     HRESSIN_F16                          Standard                EWT
10     Address                     PZ02                                             Standard                EWT
11     Bank Information     PZ03                                          Standard                Service
12     Open Appraisals     Not Available                           NA                                 Service
13     Emergency Address     PZ05                                           Standard                 EWT
14     Family/Dependents     PZ12                                           Standard                 EWT
15     Personal Data     PZ13                                               Standard                  EWT
16     Previous Employers     PZ28                                           Standard                 EWT
17     Apply Leave     WS20000081                           Standard               Service
18     Leave Overview     WS01000109                           Standard              Service
19     Leave Balance     PZ09                                             Standard              Service
20     Loan Application     ZLOAN                                          Customized              Service
ECC6.0 Scenario:
In ECC6.0, flow based services are no more supported by ECC6.0 and Dynpro based services are supported.PZM3 (Home Page) is a flow based service.
There is no replacement provided for PZM3 service, so the IMG configuration is not possible for u201CWork and Life Eventsu201D.
OSS ticket raised, but no solution for IMG u201CWork and Lifeu201D events.
List of Services would be used to set up ESS:
Sl.No     Functionality     Service/EWT/URL Name     Standard/ Customized    Type
1     Home Page     PZM3                                       Standard                           service
1)this service is not available
2)SAP does not provide any replacement.
3)PZM3 is not supported in Integrated ITS. No direct solution proposed.
4)Given reference of few notes.
5) A dynpro (module pool screen) based IAC needs to be created and links need to be provided on that screen. Generated HTML page is modified to access the services via URL or by OKCODE.
Screenshot attached below.
2           Whou2019s Who                 PZ01                                      Standard                             Service
1)this service Available
2)Not Working properly.
3) The problem may be because of the dependency with SAP Query. Either Query is missing in the new system or not having the proper authorization. Needs to be debugged and finalized.
7     Section 80C     PZ88      Standard     EWT     Available
8     Section 80      PZ80     Standard     EWT     Available
9     Form 16                HRESSIN_F16     Standard     EWT     Available
10     Address                PZ02     Standard     EWT     Available     Only EWT Available.          Service needs to be created to access the EWT.
11     Bank Information     PZ03     Standard     Service     Available     EWT Available.           Service needs to be created to access the EWT.
12     Open Appraisals     Not Available     NA     Service          EWT Available.           Service needs to be created to access the EWT.
13     Emergency Address     PZ05     Standard     EWT     Available     EWT Available.           Service needs to be created to access the EWT.
14     Family/Dependents     PZ12     Standard     EWT          EWT Available.           Service needs to be created to access the EWT.
15     Personal Data     PZ13     Standard     EWT          EWT Available.           Service needs to be created to access the EWT.
16     Previous Employers     PZ28     Standard     EWT          Service Available
17     Apply Leave     WS20000081     Standard     Service     Available, but not working                                                                               No solution is proposed yet.
18     Leave Overview     WS01000109     Standard     Service     Available, but not working               No solution is proposed yet.
19     Leave Balance     PZ09     Standard     Service     Available, but not working               No solution is proposed yet.

Ya ramakrishna,
Even easier is for you to send us the mail ID of your client. We will do the work, then send them an idoc of message type INVOICE and for you a post card of course.
Please do the needfull,
Julius

Display as Key and Name Not working properly after upgrade to Bi7.0

Hi Bw Guru's
Recently we have upgrade our BW 3.5 system to BI 7.0 (Only system upgrade not applications ).
after the upgrade we are facing lot of issues with Bex Analyzer. The following are some of the issues
1) In BW3.5 after the execution of Workbook or query ,we can convert to local currency .
Right click on workbook -> Currency translation-> Database currency .
but after upgrade to BI7.0 this is not working ..
2) Characterstic Right click on workbook Dispaly as Key and Name is also not working ..
I know that Currency translation in BI7.0 works in different way compare to BW3.5 .we can use alternate option like By Target Currency from Database currency to convert to local currency and it is working fine in Bex,but businesss users want more friendly way ...because to select the above option they have to enter local currency and rate type ...
Do you we have any notes available for the above solutions ..?Do we need to upgrade Bex version also..?Is there any document which describe how the above things works after system upgraded to BI7.0?
Please suggest me..
Thanks in advance
Shu Moh.

Dear Harita
The first issue Currency translation in query or workbook is solved with SAP note 1119549.For second issue we have not found solution until now ,Once we find the solution we will update you..
Shu Moh

Organize by conversation is not working properly after upgrade to Lion

After upgrading from 10.6 to 10.7 I've figured out that Mail Application is not very accurate with organizing by conversation. Mail from Snow Leopard was pretty nice. But after upgrade it started to make several conversation. This is very annoying especially when I'm working with support tickets.
Here is one of the example:
Mail 10.7 ( Lion )
[xxx.com #14531] Company Ecuador: training/refresh
[xxx.com #14531] Company Ecuador: training/refresh
RE: [xxx.com #14531] Company Ecuador: training/refresh
RE: [xxx.com #14531] Company Ecuador: training/refresh
[xxx.com #14531] Company Ecuador: training/refresh
[xxx.com #14531] Company Ecuador: training/refresh
Mail 10.6 ( Snow Leopard )
[xxx.com #14531] Company Ecuador: training/refresh
[xxx.com #14531] Company Ecuador: training/refresh
RE: [xxx.com #14531] Company Ecuador: training/refresh
RE: [xxx.com #14531] Company Ecuador: training/refresh
[xxx.com #14531] Company Ecuador: training/refresh
[xxx.com #14531] Company Ecuador: training/refresh
I also tried Mozilla Thunderbird. It is organizing by thread very accurate.
Is there any way how to configure this in Mail? May be I'm doing something wrong?
I like all new features of new Mail programm, but it wi very annoying.
Thanks,
Shony.

Hi Sundar & Rakesh
I've followed Sundar's request in the previous thread we worked on together to provide further assistance here:
** Scenario Summary **
The portal Work protect mode value is set to '3' ("Choose action in popup on unsaved data") When we edit a standard ESS java Web Dynpro application and click exit, the portal should show us the Work protect mode popup. Instead, the portal exits to the overview page and when we try to navigate away from the overview page, it shows the work protect mode window. This was working fine before upgrade to SAP NW 7.4 SP 5.
Ok the first point of reference and analysis here is to check and review: Workprotect mode via the following navigation path:
System Admin-> System Configuration -> Service Configuration -> Under one of the services: Work protect mode property.
Now in terms of this popup kindly ensure the configurations are setup accordingly as per the following document:
http://scn.sap.com/docs/DOC-2513
What is the setting of WDPortalWorkProtectMode.setApplicationDirty ?
Work Protect Mode
http://help.sap.com/saphelp_nw04s/helpdata/en/45/b76f4169e25858e10000000a1550b0/content.htm
Lastly have you attempted to change the property value and restarting the service ?
Restart the config by right clicking on com.sap.portal.epcf.loader. Click Administrate ->restart
Kindly update me as per your findings.
Kind Regards
Troy Cronin - Enterprise Portal Support Engineer.

App Store not working properly after upgrading to Yosemite

After upgrading from Mavericks to Yosemite. I checked the App Store's icon to see that I have 6 updates. I launched the App Store and this was my window:
This is my Purchases tab (although I am signed in):
And this is my Updates tab (Although it says 6 updates. They should be iWork and the other new Yosemite updates.):
When I click on Store -> "View my account", it keeps on asking me to sign in forever.
Also when I click on "iCloud" in preferences, I get this error which I think is related:
I tried restarting my mac several times. I tried quitting the storeagent from the Activity Log. But it's still the same.

I am having the same problem since downloading ios6
Almost wish I hadn't
Can't get YouTube as apple removed it
When I go to apps it keeps giving me a blank page too
I type in YouTube and it goes to page with cancel far left. iPad iPhone app in middle and search box for YouTube far right
But it just goes back to beginning when I cancel
Is it corrupted..will apple sort this ASAP
It's not only you tube I want...
Help apple! Or anyone

Anyone else having volume icon on ipod touch 4gen just popping up and not working properly after upgrading to ios 6.1?

Hi, has anyone experienced issues with there volume control icon randomly popping up after upgrading to ios 6.1 from 6.0 .
I have a 4th gen ipod touch which until upgrading to 6.1 from 6.0 was working perfectly.
Minutes after the upgrade I noticed the volume icon just popping up for no reason. I can turn the volume up now, but not down and it randomly appears on screen without anyone touching it. Weird! Can someone shed some light on this issue,I have reset and reloaded to factory several times now to no avail.
thanks!

I am having this same issue on my iPhone 4. The most recent update to iOS 6.1 didn't fix it either. Has anyone found a fix for this problem? It doesn't happen often, maybe every third day or so but requires power off, power on to bring the sound back.

HT1414 Linksys webcam does not view properly after upgrading to ios6

I upgraded my iPad 2 and iPhone 4 to the new ios 6. Now when I go to view my linksys web cams they do not view properly. I see the camera view for a few second, but then it goes blank. I have another iPad 2 which I did not upgrade and am still able to view with the old iOS. Seems like the new iOS 6 did something, but not sure why it will not work with the new iOS.
I access the site through the web browser.

Same problem. I two nights ago I upgraded to IOS6 on my iPad2 and can no longer call up my LinkSys cams in Safari. My iPod Touch 4 is still on IOS5 and no problem viewing cams in Safari.
I am still in Lion on my iMac but last month upgraded to Safari 6. I then lost the ability to view my cams in Safari. I went back to Safari 5.1.7 and then no more problems.
Obviously this is a Safari error. Until this is fixed, I will not upgrade to Mountain Lion.
I spoke to Apple last night and the tech said he will contact engineering. He took detailed notes so let's hope for the best.
If you need to view your cams on your devices, investigate iCam by SKJM or LiveCams Pro by Eggman Technologies. Both apps do way more than just viewing your cams. I have been using iCam for about a year for security reasons. Your cams can be set up to record on motion where images will be stored on your devices AND Dropbox.
iCam, however, is slightly difficult to set up (and sometimes maddening) but lots of info on their site as well as direct response to any problem by email. Some idiosyncrasies but hey it's only $5 and does provide security when you leave your home. Not to mention all your cams on one page if all you want to do is look at them.

Auto Sync not functioning properly after Auto Tone

Auto Sync is functioning as expected, unless I choose Auto Tone first.
I have about 1000 Images that I wish to apply a Preset to. When I created the Preset using New Develop Preset, I left all of the options checked except Exposure.
I want to use Auto Tone to set the exposure for each image automatically, and then apply my preset to all images, leaving their exposures unchanged. If I apply the Preset to all of the images before selecting Auto Tone, everyting works as expected. If I choose Auto Tone first, a small portion of the selected images will be updated, but most will not. The preset will change all settings except those in the Basic Tone area. It's as if Auto Tone has somehow become "sticky" and will not allow itself to be overridden. Even if I choose a single image, apply my new settings to it, and then manually select Sync, it doesn't work for all images. It also won't work if I have have Auto Sync selected, and then make manual changes to individual sliders. It will work for some images near the ones I see in the filmstrip on the bottom, but not all of the images selected.
This is extremely frustrating. Again, everything works exactly as expected, unless I choose Auto Tone first.

kbarre wrote:
Auto Sync is functioning as expected, unless I choose Auto Tone first.
If I choose Auto Tone first, a small portion of the selected images will be updated, but most will not.
Lightroom's handling of auto-tone leaves something to be desired - I have a lot of experience with it, trying to make reliable develop-setting plugins which include auto-toning. Those plugins have a bewildering amount of logic - something like this: initiate auto-toning, check back to see if it has properly settled, issue the auto-toning again if it never seems to be properly settling... - usually it works out after a while, but even sometimes it never does, and generates an error: can't get auto-toning to settle across all photos.
The point of all this is that there are bugs in Lr's handling of auto-toning, as you are growing aware.
Try this:
* do the auto-toning, then let it percolate for a while.
* then visit each photo at 1:1 (to force Lr to finalize settings...), and confirm auto-toning has settled...
Then try auto-syncing that preset (make sure process versions are all the same, and preset does NOT include auto-toning - I would leave process version OUT of your presets).
Better?
I don't expect this is a workflow you'll want to do all the time, but as a test it might help shed some light on the problem.
Rob

BBP_DRIVER_DETERMINE in NOT behaving properly after Upgrade to SRM5.0

The Function Modules mentioned below should be called from
Badi 'BBP_DRIVER_DETERMINE'.But we are unable to call the following
function modules from 'BBP_DRIVER_DETERMINE'.
The Badi is called only once when we click on 'Order SC'.So,as the
result none of that the following function modules are called :
B45A_GOODSMVT_CREATE
B46C_PO_GETITEMS
B46C_ATTACHMENT_CREATE
B46B_CTR_CREATE
B470_PO_CREATE.
As the result of that, we are NOT able to perform the whole cycle of
Backend documents properly.
Before upgrade Scenario:
System : SRM 4.0
The Badi 'BBP_DRIVER_DETERMINE' is called twice when we click on 'Order
SC'.So any one of the following function modules is called for
performing the Subsequent steps :
B45A_GOODSMVT_CREATE
B46C_PO_GETITEMS
B46C_ATTACHMENT_CREATE
B46B_CTR_CREATE
B470_PO_CREATE.
Do we have to add new fields to Table BBP_FUNCTION_MAP?
Waiting for the Solution.

Hi
Incase these entries are missing in the table BBP_FUNCTION_MAP, go ahead and create the entries in the table using SM30 Transaction in order that BBP_DRIVER_DETERMINE BADI can call the required function modules one by one as in Standard SRM Scenario.
B45A_GOODSMVT_CREATE
B46C_PO_GETITEMS
B46C_ATTACHMENT_CREATE
B46B_CTR_CREATE
B470_PO_CREATE
Hope this will help.
Regards
- Atul

DVR not recording properly after upgrade

After the DVR software upgrade, my DVR is now missing shows or recording both the HD and SD version of shows. It's possible it's missing shows because it can't record two shows at once because it's busy recording both HD and SD versions of the same show. There are lots of complaints on the new color scheme which I agree with, but could get used to. But if the DVR isn't going to record properly, what use is it? How do I fix this?

I'm seeing the same thing. DVR tried to record 2 SD and 1 HD broadcast of series set to All Channels, All Types, Any Time, First-Run Only. Old software only recorded HD and was smart enough to not record the concurrent SD broadcast. This is clearly a bug and the resolution is we all need to go change our config to just record the HD type? I got the same rec on twitter just now. There's just not enough people reporting the problem.
Specifics? "Formula One Racing" broadcast 11/8 on channels 90, 590, 1544. Old software only recorded 590. New software recorded 90 and 590, and when I stopped recording 90, it tried to record 1544 (I was watching another channel). Chose Cancel, then 30 seconds later got another conflict warning because it wanted to start recording 90, again. It's just annoying at this point.
BTW, new STB theme is ugly, if you're taking a poll.
*Edit* Just thought of another problem, that I'm pretty sure is happening. When deciding to record all of them, it looks like the sort is ascending channel order. If there's something else being recorded, that means that only the first SD is recorded, not the HD. At least now I understand what happened last week when my show was only recorded in SD.

NI-DAQmx 8.8 does not work properly after upgrade to LabVIEW 8.6

Hi,
I just upgraded to LabView 8.6 from version 7.1 and found out that the NI-DAQmx 8.8 drivers do not install correctly, since there is not Measurement I/O tab in the Functions palette (see attached document). The curious thing is that I can see all my NI-DAQmx devices in the MAX, and they all test correctly, i.e., they are working correctly. The sales representative for my area recommended me to uninstall , and reinstall LV8.6 and then reinstall the NI-DAQmx 8.8 drivers, but it did not work. I still do not see the Measurement I/O functions and my application says that it "cannot compile" the NI-DAQmx vi's. Thanks in advance for your help.
Peter
PS. Someone reported a similar problem back in 2003, but the final solution was not posted. Thanks again.
Attachments:
LV8.6.doc ‏116 KB

Dear Mallori,
Thanks for your help. You are right, I uninstalled and reinstalled LabVIEW 8.6 (update from LabVIEW 7.1) and reinstalled DAQmx 8.8. I still continue to have some problem that seem (to me) beyond compatibility issues. Here are the answers to your questions:
1. Before you reinstalled DAQmx 8.8, did you
uninstall it? If not, then I believe that the installer would see the
driver already present and not actually make any changes.
REPLY: No, I did not uninstall DAQmx 8.8. What do you recommend? Should I uninstall BOTH LabVIEW 8.6 and DAQmx 8.8 and then reinstall everything again?
2. When you say that the VIs are not responsive,
could you describe this a bit better? Perhaps post one of the error
messages about compiling that you mentioned in your first post?
REPLY: I am having a lots of "This SubVI is not executable" error messages in many of the library VI's not even mine. See the attached file.
3. If you open the NI Example Finder (Help»Find
Examples) and the expand Hardware Input and Output»DAQmx»Analog
Measurements»Voltage, are you able to run one of the example programs
and see the correct values that you see in the Measurement and
Automation Explorer Test Panels?
REPLY: I tried to runa couple of the examples for continuous voltage acquisition (internal clock) and both open with errors (see attachement).
Thanks again for your help. I am looking forward to your recommendation.
Regards,
Peter
Attachments:
LV8.6-3.doc ‏43 KB

Bluetooth not working properly after upgrade to iOS4

I upgraded my iPhone 3g to iOS4 the other day. Apart from running stupid slow now, and even though i've done numerous hard resets, the bluetooth doesn't work properly anymore.
If I switch off bluetooth, then switch it on, it connects fine. Once I disconnect though, that's it. I have to restart it again.
Looks like all those complaints about iphone 4 are actually and iOS4 BUG.
I wish I'd never upgraded now. Actually, that's not true. I wish Apple would help me DOWNGRADE my iphone 3g so i can use it again. I will not go and buy and iphone 4 just cos of this. If anything I'll switch to Android just because a) i'm not a fanboy and b) consumers should not be treated in such a belligerent manner.
So, anyone know how to resolve this bluetooth issue? It's got to the point where it's dangerous in the car because my phone rings and I have to recycle the bluetooth to connect it.
Message was edited by: anthonybrooker

The problem you are having following the upgrade to Leopard (10.5.6) from 10.3.9 is similar to those of people who have upgraded from Tiger, and has been covered by the support document at the link below:
http://support.apple.com/kb/TS2537
Your issue will be due to files named to include MessageSorting (which would mean you once have upgraded from a version of OSX earlier than 10.4), remove those, also, but never restore those. You will not have the files named to include MessageRules because you have not used Tiger.
To find the correct location for the Mail folder, open a Finder window, click on the icon of a house in the Sidebar (this is known often as "Home"), click on Library in that Home user directory, and then to open the Mail folder found there.
Ernie

USB 2.0 not functioning properly after upgrading to 3.10.3-1 kernel

Similar Messages

Maybe you are looking for