Usb 3.0 harddisk not accessible via usb 3.0 port

Hey guys,
When I connect my iomega usb drive to my usb2 port, it works fine. However – though it used to work before – when I connect it to my usb 3.0 port I get the following errors:
Feb 28 10:59:13 elefant kernel: [ 219.390214] scsi 22:0:0:0: Direct-Access OEM Ext Hard Disk 0000 PQ: 0 ANSI: 5
Feb 28 10:59:13 elefant kernel: [ 219.548833] usbcore: registered new interface driver uas
Feb 28 10:59:13 elefant kernel: [ 219.598091] sd 22:0:0:0: [sdd] 244188086 4096-byte logical blocks: (1.00 TB/931 GiB)
Feb 28 10:59:14 elefant kernel: [ 219.746744] sd 22:0:0:0: [sdd] Write Protect is off
Feb 28 10:59:14 elefant kernel: [ 219.746749] sd 22:0:0:0: [sdd] Mode Sense: 10 00 00 00
Feb 28 10:59:14 elefant kernel: [ 219.793651] sd 22:0:0:0: [sdd] Cache data unavailable
Feb 28 10:59:14 elefant kernel: [ 219.793655] sd 22:0:0:0: [sdd] Assuming drive cache: write through
Feb 28 10:59:14 elefant kernel: [ 219.891832] xhci_hcd 0000:02:00.0: WARN: babble error on endpoint
Feb 28 10:59:14 elefant kernel: [ 219.891967] xhci_hcd 0000:02:00.0: WARN Set TR Deq Ptr cmd invalid because of stream ID configuration
Feb 28 10:59:14 elefant kernel: [ 219.892062] xhci_hcd 0000:02:00.0: ERROR Transfer event for disabled endpoint or incorrect stream ring
Feb 28 10:59:44 elefant kernel: [ 249.909031] sd 22:0:0:0: uas_eh_abort_handler tag 0
Feb 28 10:59:44 elefant kernel: [ 249.909038] sd 22:0:0:0: uas_eh_device_reset_handler tag 0
Feb 28 10:59:44 elefant kernel: [ 249.909042] sd 22:0:0:0: uas_eh_target_reset_handler tag 0
Feb 28 10:59:44 elefant kernel: [ 249.909045] sd 22:0:0:0: uas_eh_bus_reset_handler tag 0
Feb 28 10:59:44 elefant kernel: [ 250.026458] usb 3-1: reset SuperSpeed USB device number 2 using xhci_hcd
Feb 28 10:59:44 elefant kernel: [ 250.142147] xhci_hcd 0000:02:00.0: WARN: short transfer on control ep
Feb 28 10:59:44 elefant kernel: [ 250.142278] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff8802dadf2300
Feb 28 10:59:44 elefant kernel: [ 250.142282] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff8802dadf2340
Feb 28 10:59:44 elefant kernel: [ 250.142286] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff8802dadf2380
Feb 28 10:59:44 elefant kernel: [ 250.142289] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff8802dadf23c0
Feb 28 10:59:44 elefant udevd[223]: worker [884] timeout, kill it
Feb 28 10:59:44 elefant udevd[223]: seq 2338 '/devices/pci0000:00/0000:00:02.0/0000:02:00.0/usb3/3-1/3-1:1.0' killed
Feb 28 10:59:44 elefant kernel: [ 250.373859] usb 3-1: URB BAD STATUS -108
Feb 28 10:59:44 elefant kernel: [ 250.373877] sd 22:0:0:0: Device offlined - not ready after error recovery
Feb 28 10:59:44 elefant kernel: [ 250.373950] sd 22:0:0:0: rejecting I/O to offline device
Feb 28 10:59:44 elefant kernel: [ 250.373959] sd 22:0:0:0: rejecting I/O to offline device
Feb 28 10:59:44 elefant kernel: [ 250.373964] sd 22:0:0:0: [sdd] READ CAPACITY(16) failed
Feb 28 10:59:44 elefant kernel: [ 250.373967] sd 22:0:0:0: [sdd] Result: hostbyte=0x01 driverbyte=0x00
Feb 28 10:59:44 elefant kernel: [ 250.373971] sd 22:0:0:0: [sdd] Sense not available.
Feb 28 10:59:44 elefant kernel: [ 250.373975] sd 22:0:0:0: rejecting I/O to offline device
Feb 28 10:59:44 elefant kernel: [ 250.373980] sd 22:0:0:0: rejecting I/O to offline device
Feb 28 10:59:44 elefant kernel: [ 250.373984] sd 22:0:0:0: rejecting I/O to offline device
Feb 28 10:59:44 elefant kernel: [ 250.373988] sd 22:0:0:0: [sdd] READ CAPACITY failed
Feb 28 10:59:44 elefant kernel: [ 250.373990] sd 22:0:0:0: [sdd] Result: hostbyte=0x01 driverbyte=0x00
Feb 28 10:59:44 elefant kernel: [ 250.373993] sd 22:0:0:0: [sdd] Sense not available.
Feb 28 10:59:44 elefant kernel: [ 250.373997] sd 22:0:0:0: rejecting I/O to offline device
Feb 28 10:59:44 elefant kernel: [ 250.374001] sd 22:0:0:0: rejecting I/O to offline device
Feb 28 10:59:44 elefant kernel: [ 250.374007] sd 22:0:0:0: rejecting I/O to offline device
Feb 28 10:59:44 elefant kernel: [ 250.374011] sd 22:0:0:0: rejecting I/O to offline device
Feb 28 10:59:44 elefant kernel: [ 250.374015] sd 22:0:0:0: [sdd] Asking for cache data failed
Feb 28 10:59:44 elefant kernel: [ 250.374017] sd 22:0:0:0: [sdd] Assuming drive cache: write through
Feb 28 10:59:44 elefant kernel: [ 250.374021] sdd: detected capacity change from 1000194400256 to 0
Feb 28 10:59:44 elefant udevd[223]: worker [884] terminated by signal 9 (Killed)
Feb 28 10:59:44 elefant kernel: [ 250.374103] sd 22:0:0:0: [sdd] Attached SCSI disk
Feb 28 10:59:44 elefant ata_id[2039]: unable to open '/dev/sdd'
Anybody an idea, what I could do about that?

The always on is not a USB 3.0, it is just a regular 2.0 port.
Regards,
Jin Li
May this year, be the year of 'DO'!
I am a volunteer, and not a paid staff of Lenovo or Microsoft

Similar Messages

When Using iOs 7.1.2 OSX 10.9.4 notes are not syncing via USB. When will this be fixed. Not interested in iCloud or IMAP solution.

When Using iOs 7.1.2 with mac OSX 10.9.4 mavericks notes are not syncing via USB.
When will this be fixed ? Not interested in iCloud or IMAP solution. it worked before, I can't really
understand why apple would change one of my favorite features. I use the notes feature to
capture quick ideas on the road and having it synched on my computer and my phone was very useful.
Previous blog posts elsewhere indicated this would be fixed in the latest rev of iOS, OSX and iTunes.
But alas after the recent update it's not. Really Annoying.

poweruser_art wrote:
When Using iOs 7.1.2 with mac OSX 10.9.4 mavericks notes are not syncing via USB.
When will this be fixed ? Not interested in iCloud or IMAP solution.
Then you won't be syncing your notes anymore.
Contacts and Calendars are the only things they restored.
iOS: How to transfer or sync content to your computehttp://support.apple.com/kb/HT1296

Usb composite device is an older usb device and might not work in USB 3

I recently bought one Lenovo Yoga 2 11 laptop running Windows 8.1 (64 bit).
When I try to connect my old Brother MFC-3240C printer using USB (2.0), it doesn’t work.
Below are the steps performed:
Connected the printer to USB 2.0 port on laptop (on the right side). Automatically installed the printer driver (no exclamation mark beside printer icon)
When the printer didn’t print, I tried to use troubleshoot as below:
Control Panel->Hardware and Sound->Devices and Printers->Right Click on Printer Icon->Troubleshoot.
It came up with USB composite device is an older usb device and might not work in USB 3.0
Removed the printer and re-installed the driver. It is all the same.
Any help will be greatly appreciated.
FYI – the same printer works fine with my older laptops running Windows 7.

Already checked Brothers website for the printer drivre for Windows 8.1 (64 bit).
It says ... The built-in driver is already included with Windows® Operating System or is available through Windows® update.
So, installed the default driver for the printer that is available with Windows 8.1.
Even connected the printer with USB 3.0 port on the laptop, but it is all the same.

HT5634 I already install bootcamp 5 on my Macbook Pro MD101 (Mid 2012). But when I plug the USB, my Mac can not recognize the USB or any Storage device. Pls help

I already install Bootcamp 5 on my Macbook Pro MD101 (Mid 2012) but when I plug the USB, my Mac can not recognize the USB, also any storage device. Pls help !!! I am using Window 7

I ran an Apple Hardware Test, says ''No trouble found'.

Personal Hotspot on iPhone 4s not working via USB cable

In the last couple of weeks, I have not been able to use the Personal Hotspot on my iPhone 4s via the USB/sync cable to either of two 2011 Macs, both running the latest version of Lion, with all relevant software updated, including Flashback removal & Java updates. The connection via Bluetooth & wi-fi is unaffected.
Opening the Network System Preference pane, the connection is shown as iPhone USB, but it is not connected, even with all other internet access methods either deactivated or disconnected.
This issue is related to Lion, as the G4 & G5 PPC Macs running 10.5.8 which I either use or administer are not affected by this problem. The iPhone is running on iOS 5.1 and is not jailbroken.
Is it possible that the Flashback/Java issues and Apple's interpretation of their prevention/removal has affected this aspect of internet access via Personal Hotspot?

Hey, where did that "I have this problem too" link come from?
I have this problem too.

HP Officejet Pro 8500A 910A, Vista 32-bit, will not connect via usb to my PC!!!

I used to have this all in one connected to my pc, until I was experiencing a few printing issues, so I decided to uninstall it! When I tried to reinstall it, the pc will not connect it. I have tried different ports and have replaced the cable, also downloaded the latest software and drivers all to no avail. I can connect wirelessly to my laptop, but unfortunately this isn't a solution for my desktop as it's not wireless, therefore it has to be connected via usb. At my wits end, please help me!!!!!
This question was solved.
View Solution.

Hello,
Can you try inserting a flash drive into one of the USB ports in the printer, to make sure it reads it?
The port on the printer might be what's giving you the issue. Also, can you try connecting the printer USB to a different PC?
Let me know the outcome.

Ipad 1 suddenly does not appear in iTunes and down not load via usb

All of a sudden my ipad1 is not recognised by itunes.
Also no loading activity via usb.
I use Imac with lion.
My ipad3 runs prefectly.

Try something very simple .... quit iTunes, reboot the iPad and then restart the Mac and try again.
Reboot the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons.

N9 not detected via USB connection

Since last few months I have observed that my Nokia N9 is not detected via any PC if connected via USB cable. The USB cable is OK because my other devices are easily detected through same cable. Can anyone suggest solution. I have already try to "Clear device" under settings->Reset.
Please help.

@girishpadia
Presumably your N9 still charges when connected to PC USB?
Does this apply to both Nokia Suite and Mass Storage mode presupposing that Nokia Suite is installed upon PC?
Happy to have helped forum with a Support Ratio = 42.5

E72 - Calendar not syncing via USB data cable (Out...

PROBLEM:
Syncing the E72-2 Calendar to Outlook over USB Data cable returned synchronization errors.
HISTORY:
Previously was using MfE and Google Calendar as a go-between from Outlook 2003 to my E72. It worked OK for a couple of weeks, but then turned to **** (appointments disappearing from phone, duplicates that couldn't be deleted, sending tons of 'decline' messages to work colleagues from my personal Gmail account...etc. etc.) It is abundantly clear that MfE and Google Calendar were not meant to play together at this point in time.
Next strategy was to use PC Suite to sync with the Outlook calendar directly via cable. This was not successful either. The default Sync profile on the phone only offers Data Bearer of Bluetooth or GPRS, no cable. Sure enough, PC Suite would fail immediately with 0 events synced, saying to check the Idle status of the phone.
SOLUTION that worked for me:
Overview:
- Delete all calendar entries on the phone, even those that are 'stuck'. (Note: you DON'T need to wipe your phone for this - that is Nokia's lazy solution but there are easier ways.)
- Run PC Suite Cleaner from Nokia
- Reinstall PC Suite
- Run PC Suite, connect the phone via USB only when prompted
- Configure the Sync profile on the phone
- Configure the Sync application on the PC
- Sync!
Details:
0a. Clean off all calendar entries from the phone. To get rid of stubborn ones, you can try to sync the phone via bluetooth or internet to an empty Google or other calendar to remove all entries. (I did this by syncing to an empty iCal calendar on my Mac) Alternatively, you can also connect the phone to PC Suite, then open the phone calendar in PC Suite and delete all appointments using the trash can button. (Recurring series will only need to be deleted once.)
0b. Exit PC Suite. Ensure it is not still running in the Taskbar.
1. Run the Nokia PC Suite Cleaner, downloadable from Nokia's support site. Restart when prompted.
2. Re-install PC Suite version 7.1.40.6
3. Run PC Suite before connecting the phone.
3a. Select Cable connection, then connect the phone when prompted.
3b. PC Suite should install the necessary drivers and software (if this is working, you will see several USB device popups in your taskbar.)
4. On the phone, go to Ctrl Panel --> Phone --> Sync.
4a. If you have been messing around with MfE or other sync methods, delete those extraneous sync profiles from the phone. Go to "Change Active Profile" - if you see anything besides 'PC Suite', select it and then choose 'Delete' from the Options menu.
4b. After any extra Sync profiles are gone, the phone will default back to 'PC Suite.' Ensure the PIM data you wish to sync (Calendar, etc.) is selected with a red X.
4c. It does not seem to matter what you select for Data Bearer - I am using Bluetooth and that's working even though the target PC does not have it.
4d. 'Allow sync requests' should be set to 'Automatically accept'
4e. For 'Synchronization type' select the value that works for you. ('To phone only')
5. Run the Sync application in PC Suite.
5b. Ensure the phone has not automatically locked itself.
5c. Click the 'Sync' button in the PC Sync app.
5d. You should see Connecting....Waiting....Reading.....etc. while the content is syncing.
5e. If it stops after Waiting and returns a communication error, you may need to try the above steps again, and/or do a clean install on your phone. :-(
Hope this helps someone out there. Note that this is mostly from memory, so if I inadvertently skipped any steps or if anything needs further clarification, please respond to this thread to help future readers.

Herve55 I can confirm that the DC-6 (remember to buy the the one with USB-micro connection) works.
However the only reason for me wanting to use the supplied USB to USB-micro cable in the car (with 3rd party cigarette adapter) was to first, get rid of that annoying spiral cord and second to have the data cable with me at all times.
Sad to say that I´eve by now definitely tried all possible solutions for the data cable "CA-101" without any luck.
My N97 witch I was very satisfied with at start started to burn battery,reboot,loose memory, become sluggish and then after 8 months of aggravation i sent it on a flyer in the wall.
I have now after 15 years changed brand.
Conclusively the guys at Nokia seems to carry to many models for any possibility of making further great phones! in other words they´v gone sloppy.

6303i classic not connectes via USB

My new 6303i will not connect to the PC via USB. Is there a special driver for my WIN7 installation? OVI Suite is installed.
What else can I do?
Regards for help.
Helmut - Germany
PS Screen says No connection possible

You are correct, charging is using the charging port and also using a USB cable. It is strange that the accesories page for the 6720 only lists chargers that plug ionto the charging port. See link below.
http://europe.nokia.com/find-products/accessories/all-accessories/power
Maybe someone with a 6720 can confirm this.
I just checked the phone spec here and it only says "2mm charger connector". It normally says "usb charging" if usb charging is possible.
Message Edited by cjlim on 06-Nov-2009 09:50 AM

IPhone not charging via USB

I just got this weird problem today. I have a 2G iPhone running 2.2
1. iPhone is not charging with the USB cable to my MacBook and not recognizing by iTunes, thus I can't sync anymore.
2. I can use the same USB cable to charge the iTouch from my MacBook
3. I can use the same USB vable to charge the iPhone charges via the wall adapter, so this can not be the USB cable.
4. I can use the same USB cable for the iTouch and I see it in iTunes
So, this is not the USB cable nor iTunes. However, if this is hardware issue with the iPhone with charging, how come I can charge it using the wall adapter??
This is very very strange indeed. Would it help if I do a hard reset on the phone? If so, how do I do that as I can not find anything on hard reset in the manual.
help!

I have two USB cables, one for the iPhone and one for the iTouch. Both cables do not work for the iPhone but they work for the iTouch.
Also, I can use both cables to charge the iPhone from the wall charger. My problem is the iPhone does not seem to charge with the same cable plugging into my MacBook and iTunes does not see the device.
My last sync with iTunes was yesterday. This problem just started today. I did a hard reset on the iPhone, no luck.

Code 31 Error / Playbook not connecting via USB

My Setup:
Windows 8 Pro x64
AMD FX 3.1Ghz
I'm trying to connect my 64gb Playbook running OS version 2.1.0.1526 to my computer via USB.
So, I've tried atleast 3 different things from various other posts.
- Updating drivers ( I bought the driverupdate.net package last night )
- Allowing ports 80 and 443 then again by disabling 80 and 443
- Uninstalling device manager / reinstalling / rebooting / restarting the PB
- Turned off wireless connections on the PB
The worst part is, is that the Desktop Manager software sees that the PB is connected to the computer. It shows up with my PIN # etc. but it still says Connect the device. Also the Playbook itself says that it is connected to the computer. So frusterating!!!
I click connect the device and in about 10 seconds the program goes into (Not Responding) and 10 seconds after that I get the error - "Blackberry desktop software can't communicate with the connected device"
I have had the PB connect wirelessly with my computer but the file transfer speeds are terrible and inconsistent. Thank you for taking the time to read this and hopefully lend any information or tips.
Cheers

I FOUND THIS, TRY IT:
http://forums.crackberry.com/blackberry-playbook-os-f228/driver-error-blackberry-desktop-windows-8-p...

N80 PC Suite not-connecting via USB

Connected once via USB cable (CA-53), but won't connect again.
N80
PC Suite version 6.80.53.3
Windows XP Pro version 2002
Service Pack 2
No anti-virus running or firewall upon installation.
Phone data cable mode-"PC Suite"
No USB connection "beep" on laptop.
No error message, just the typical "working" icon.
Did spend some time searching the discussion site, but couldn't find anything.
Appreciate any suggestions or help out there in cyber...
Thanks

I do not recognise the PC Suite version ? If there is no bleep sound, if indicates that the physical connection does not happen, so pressing the connector firmly to its place might help, also changing the usb port in your pc

EliteDisplay s231d not connecting via USB

I have an EliteDisplay S231d. I cannot connect via USB to my laptop. I can see the display in connected devices, but cannot switch to it and use the built in hub.
I have downloaded the latest drivers and software for your site.
I have Windows 8.1pro and am connecting via the out port of the screen using the included USB cable to a USB3.0 port.
The serial number of my screen is 6CM4380VDW.
Cheers,
James

The mini usb plug goes into the centre port at the bottom on the PlayBook. The RIM symbol must be up if you will damage the connection if inserted the wrong way. I put a white dot onto the correct side of the plug to make sure I get it right.
You may have a firewall setting on your computer that keeps you from connecting to the PlayBook .
If you go back to the top section of this forums home Page, there are several sticky notes. One deals with the BlackBerry Knowledge Base articles. Go there and enter some info into the search box. It will list some articles which may help you further.

New Officejet Pro 6830 will not print via USB connection. It scans great to PC. It copies.

New HP Officejet Pro 6830 for user to have local USB printer/scanner at desk. User runs win 7 64 bit on a network. Raninstall through setup.exe. Followed steps, connected printer via USB when it said to and it detected it and finished install.You can use HP Scan software and it scans to the PC perfectly. It will not print from any application or even a testpage from the Printer Properties page. If you go to the maintenance application it will print status and test page. If you run HP Scan and Print doctor it does it's thing, gives all Green Check marks and lets you print a test page fine, but it stillwill not print even a test page from the printer properties page (start/Devices and Pritners/right click on Officejet Pro 6830, select Printer Properties for Officejet Pro 6830 (not the Fax 6830), and click print test page. It does not seethe printer. It is a networked PC and has network defined HP network printers as well but user wanted a printer/scanner at his desk. I actually took the unit and connected to my laptop which is same win 7 64 bit platform and it does the same thing. I disable the virus protection to do the install so that is not an issue. It clearly sees and installs the printer, andlike I said the HP Scan works fine so it is connected via the USB to the PC, but it will not print. I have tried to install from the CD, and removed device and tried to install from the new downloaded drivers as well and it just does not want to print.I have conected to different USB ports, and like I said actually tried it on a different PC and had same results. Guidance certainly would be appreciated.

Hi , I see by your post that you can scan, but are unable to print over the USB connection. I would be happy to help you.
I have provided a document for setting Security permissions for printing to see if that will help. If the issue persists, reinstall the printer on the Administrator Account to see if you have the same results.Unlock Hidden Administrator Account and install the printer on this account: Go to your Start menu and under the 'search programs and files' box type CMD. CMD will populate as a search option above, just right click on it and 'run as administrator'. Once CMD (Command Prompt) opens, type net user administrator /active:yes and hit enter. Next, close CMD and restart your computer. When your computer comes on log into the new account that should show. It will be called Administrator and will not have a password on it. If your computer automatically logs into your account after restart than go to your start menu click the arrow beside 'shutdown' and choose 'switch user'. Now log into the Administrator account we just unlocked.Under the Administrator account, install the printer software. Test the printer. To turn off the Admin account start back at step 1 and type in net user administrator /active:no.Please let me know the outcome. If you appreciate my efforts, please click the 'Thumbs up' button below. Thank You.

Usb 3.0 harddisk not accessible via usb 3.0 port

Similar Messages

Maybe you are looking for