Usb 3.0 port works with slow speed

i have hp 15r-007tx laptop
when i try to use usb 3.0 port it works with usb 2.0 speed i have inserted in correct usb port and  installed all the drivers but still speed is very slow 

vibhors wrote:
using transcend hdd 500 gb just movies getting 20-25 mbps speed same as usb 2.0
Hi,
What is the model of your transcend ? Is it USB 3.0 drive ? How big each movie ? Many smaller movie files will slow  them down.
Regards,
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Similar Messages

  • External USB HD does not work with HAL:

    External USB HD does not work with HAL:
    From the last 10 days the HAL auto-mount with ntfs-3g file system of my external hard drive  does not woks.
    But the manual mount procedure with the command mount -t ntfs-3g /dev/sdb* /mnt/XYZ works.
    I've followed the instructions in the wiki: http://wiki.archlinux.org/index.php/HAL and the system has worked up to the last kernel or HAL update.
    My fat32 usb-stick works without any problem.
    If I try to open the device with KDE it appears an error popup wit this message:
    TODO: have to rethink extra options
    Error: kio_media_mount_helper
    The log from the kernel.log is
    Nov 6 22:03:16 myhost usb 5-1: new high speed USB device using ehci_hcd and address 4
    Nov 6 22:03:16 myhost usb 5-1: configuration #1 chosen from 1 choice
    Nov 6 22:03:17 myhost Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
    Nov 6 22:03:17 myhost ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
    Nov 6 22:03:17 myhost Initializing USB Mass Storage driver...
    Nov 6 22:03:17 myhost scsi6 : SCSI emulation for USB Mass Storage devices
    Nov 6 22:03:17 myhost usb-storage: device found at 4
    Nov 6 22:03:17 myhost usb-storage: waiting for device to settle before scanning
    Nov 6 22:03:17 myhost usbcore: registered new interface driver usb-storage
    Nov 6 22:03:17 myhost USB Mass Storage support registered.
    Nov 6 22:03:22 myhost scsi 6:0:0:0: Direct-Access WDC WD32 00JB-00KFA0 0811 PQ: 0 ANSI: 0
    Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
    Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Test WP failed, assume Write Enabled
    Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Assuming drive cache: write through
    Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
    Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Test WP failed, assume Write Enabled
    Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Assuming drive cache: write through
    Nov 6 22:03:22 myhost sdb: sdb1
    Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Attached SCSI disk
    Nov 6 22:03:22 myhost sd 6:0:0:0: Attached scsi generic sg2 type 0
    Nov 6 22:03:22 myhost usb-storage: device scan complete
    and the error.log is
    Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Assuming drive cache: write through
    Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Assuming drive cache: write through
    Do you have some idea ....
    Bye.

    I have done the following:
    Downloaded the patched hal version.
    used makepkg in /abs/local/trunk/ to create a pkg for pacman
    used sudo pacman -U pkgname to install it.
    used sudo nano /etc/hal/fdi/policy/preferences.fdi to create the fdi file with the following content:
    saved the file and removed my ntfs entryes from fstab and rebooted. and still there is no automount off ntfs partitions.
    have i done something wrong?
    br fjodork
    WARNING: what follows is a guide of what did work for me, I'm still in an early stage of learning linux, so please correct me if anything of what follows is wrong/dangerous/stupid. As I said, this worked for me, it's not pretty, since I was learning each step on the fly and I'm sure there are better ways to do this.
    So fjodork, you seem to have done the the necessary steps, though i couldn't get it to work until i first removed hal without dependencies
    pacman -Rd hal
    it will give you some warning about the dependencies, ignore  it since we are reinstalling hal in a few steps.
    First i tried to follow Raymano's link, obviously it showed me nothing in the browser so I thought it might be a broken link.
    So I downloaded the source tarball from here http://hal.freedesktop.org/releases/hal-0.5.10.tar.gz
    unpacked it changed the /tools/hal-storage-mount.c as per Milfadoodle's instructions.
    at first I tried to compile directly from source, the process would finish without a glitch though after reboot nothing changed, as if hal weren't
    installed, i guess there were issues with paths. anyway read on
    Then repacked the source in tarball, copied it to /var/abs/extra/system/hal and modified the PKGBUILD as follows
    makedepends=('pkgconfig' 'gperf')
    options=('!libtool')
    install=hal.install
    source=(${pkgname}-${pkgver}.tar.gz #removed url so makepkg looks in the current directory for the tarball
        hal
        hal-policy.patch
        cryptsetup_location.patch
        hal-0.5.9-hide-diagnostic.patch
        ntfs3g-valid-options.patch)
    md5sums=('6641c30a27c00485c6accac5110ff911' # replace with md5sum of your package's sourceball (run md5sum filename)
             '882f67668cb14a0a9e4a27ef22278027'
             '5ba8b610aa9763a5f42b9f7cbd7a86ad'
    then makepkg (i had to add --asroot, don't ask why
    and finally pacman -U hal-0.5.10-1-i686.pkg
    another reboot and everything worked without a glitch!:D (yeah i know i still haven't got rid of the reboot mentality )
    I have also put the policy files as per the wiki instructions.
    PS: I know this is a dirty way to getting things done but as i said, I'm just starting
    If anyone could comment/correct/explain this post I'd be more than happy, the automount issue was bothering me for about a month now (you'll say why do I need ntfs in the first place? well, I only recently switched for Linux as my primary OS, these are some relics of the M$ era

  • Looking for a way to get my Product ID and Vendor ID so I can enable my Radium 49 USB MIDI keyboard to work with Labview 7

    Looking for the Product ID and Vendor ID for my Radium 49 USB MIDI keyboard to work with Labview 7
    Is there a tool to find out the Vendor ID and Product ID for a USB device?
    Example: of what I'm looking for
    The Product ID for National Instruments DAQPad-6020E is 0x12C0. The
    USB vendor ID is 0x3923. This is a 16-bit hexadecimal number(1093)
    (that is decimal 4243).
    Thanks for all the fast responses this newsgroup RULES!!!!!!!!!!!!

    http://digital.ni.com/public.nsf/allkb/335A90747734097886257070006415B9
    How To Find The Vendor and Product ID for USB Devices?
    Primary Software: Driver Software>>NI-VISA
    Primary Software Version: 3.3.1
    Primary Software Fixed Version: N/A
    Secondary Software: N/A
    Problem:
    I want to make an NI-VISA driver that requires the vendor and product ID?
    Solution:
    There is a utility called USBView,
    free from Windows, attached below, which you can use to view what is
    connected to your computer's USB ports. It is necessary to load this
    program and connect the USB device in development. Upon selecting the
    device in USBView, one can then look on the right side of the
    application window to obtain the Product ID and Vendor ID. This will
    allow you to enter in the correct IDs when creating a driver .inf file
    when using the VISA Driver Development Wizard. For more information
    about how to use the VISA Driver Development Wizard see the related
    links below.
    Note: It is necessary to keep the hexadecimal
    (0x####) format. Do not remove the "0x" hexadecimal format preceding
    the ID number. 

  • Can Minidisplay Port work with the new Thunderbolt Display?

    I have a 2009 MBP 15 inch with Mindisplayport.
    Can Minidisplay Port work with the new Thunderbolt Display?
    If not, is there any adaptor i can use to make it work.
    I also have the new MBA with thunderbolt socket.
    Cannot decide which display to get.
    Thanks.

    Here's a new article that basically covers and clears up all the new Thunderbolt display questions (same things I previously stated).
    Enjoy!!
    http://www.tuaw.com/2011/09/18/thunderbolt-display-daisy-chaining-spec-cleared-u p/

  • My firewire port works with ext hd but not with audio interface

    2010 Imac 21.5 running 10.8.5. My firewire port works with ext hd but not with audio interface. The local authorized Apple tech said that I need a new motherboard, but my firewire ext drive works perfectly. I don't understand. Thanks.

    You must go to the website of the audio interface manufacturer and look for, download and install updated drivers for the audio device you are using.
    This is not, neccessarily, an Apple issue.

  • Why has my USB Superdrive suddenly stopped working with my MacBook Pro?

    Why has my Apple USB SuperDrive suddenly stopped working with my MacBook Pro?
    Normally I plug it in and insert a CD or DVD and it is immediately recognised, but today it took the DVD, made a 'whirring' noise for a few seconds and then stopped without being recognised.

    Try the options on this list:
    Credit Kappy.
    Try 1 and 5.
    Ciao.

  • Is there such a thing as a USB WIFI adapter that works with OS X 10.9?

    Is there such a thing as a USB WIFI adapter that works with OS X 10.9? I have tried 3 different models, none of which were compatible. The built-in WIFI card in a 2012 Mac Pro is absolutely crap (0/10 on the performance scale). Any recommendations?

    Hey everyone, yes I have installed the drivers properly. I've used an ASUS, Bolse, and EDIMAX adapter. Some had a 10.8 driver, some had 10.9. After reaching out to customer support for each and every one of these companies for help, and through multiple returns, I have not gotten anywhere with any of the drivers or products.
    It's getting ridiculously hard to stay an Apple customer when the quality of their products are getting worse and worse, which leaves me no choice but to go to third parties to replace the faulty hardware.
    And honestly I'm just sick of calling India every day to get my issues resolved.

  • USB webcam microphone not working with Starcraft 2 voice chat

    =USB webcam microphone not working with Starcraft 2 voice chat?Windows 7, X-fi Fatalty Pro
    I have a webcam with ?a built in microphone (Ps3 eye). ?It is connected by USB. ?The drivers are the CL-Eye drivers; a third party driver set since Sony does not directly support the eye for PC.
    in the windows audio device management, the microphone appears as normal and is set as the default device. ?I can use the windows sound recorder to record me speaking just fine. ?However if I use any other applications it doesn't seem to work at all. ?I can select the device as the default recording device in Starcraft 2 as well as Teamspeak 3 but no sound is detected. ?The USB microphone does not show up as a selectable device in recording options in my Creative Control Panel. ?Disabling the default creative microphone does nothing.
    I think the problem is in that windows can directly detect the microphone and so software that uses the windows audio device manager works fine, but anything that talks directly with my sound card software does not properly detect the microphone. ?Basically, I can select the device as a default device but it does not work.
    Any thoughts on this or am I SOL and have to find myself a shiny new headset?

    I had the same problem. You need to check the device index of your USB mic.
    In my case. I'm on a Mac OSX 10.6 system. I had four devices cataloged. With the last one being the USB mic.
    Then set like so in your AS code audioPub.microphoneManager.micIndex = 3;
    Remember, that the indexing is 0 based.
    The sound framework make the assumption that the index is 0.
    Hope that helps.

  • Which usb 3 hubs really work with a 2012 Mac mini?

    Which usb 3 hubs really work with a late 2012 Mac mini?

    http://www.amazon.com/gp/product/B00ADM79N6?gclid=CNr-ta3hnLkCFcdxQgodLH0AGg
    I use that one - 2 DVD drives, 2 external HDD, Webcam, keyboard/mouse and 2 flash drives... all really fast.

  • Left most usb port works with usb 3 devices but not with usb 2 devices

    Can someone enlighten me on this issue? I have a MBP mid 12 that seems to have issues with usb 2 devices such iPods, HHDs, etc. The same port works fine with usb 3 devices. I have tried several solutions but not avail such as resetting the SMC, PROM, disconnecting the battery and reinstalling OS X from scratch. Is there anything Im missing? I still don't believe is a hardware issue but something wrong in the firmware...

    Can someone enlighten me on this issue? I have a MBP mid 12 that seems to have issues with usb 2 devices such iPods, HHDs, etc. The same port works fine with usb 3 devices. I have tried several solutions but not avail such as resetting the SMC, PROM, disconnecting the battery and reinstalling OS X from scratch. Is there anything Im missing? I still don't believe is a hardware issue but something wrong in the firmware...

  • Apple USB keyboard does not work with one internal usb port

    Hi everyone,
    hope someone can help me to solve my problem. I have a MPB13 retina late 2013 since something like 3 months. I have additional screen (dell), usb wired keyboard (apple) and BT magic mouse.
    Since a few days, my usb keyboard does not work well. It only want to work properly when plugged to the rights side usb port internal port and not anymore on the left one. It also work on a usb external concentrator. Before, I had no problem, it worked perfectly. There was no problem such as cofee on it...
    After searching the web on such problem, I tries a few things such as:
    I tried the keyboard on another computer (windows): works fine
    I tried usb stick and external DVD reading on the left internal usb ports: works fine
    I switch the MPB off and turn it back on: the usb keyboard still does not work on the left usb port
    I tried the SMC and PRAM reset : nothing
    Any idea ??
    Thanks
    Guillaume

    I'm facing the same problem, found any solutions ?

  • My Apple USB mouse is not working with Mac OS X 10.6.8

    Any ideas?
    My USB Mighty Mouse is no more working with my Mac (OS X 10.6.8). I haven't used it for long, but now it doesn't work anymore.
    When I plug it into the USB port, Mac does recognize it but it seems like frozen. Red light under the mouse is on, but no signs from the mouse.
    I checked in the system profiler and the mouse appears among the USB hardware, as
    Mouse Apple Optical USB Mouse
    Product  ID:          0x0304
    Supplier ID:          0x05ac (Apple Inc.)
    Version:           1.10
      Speed:          Until 1,5 Mb/sec
      Produttore:          Mitsumi Electric
      ID posizione:          0x04100000 / 2
      Corrente disponibile (mA):          500
      Corrente necessaria (mA):          100

    I am sorry, but to get your issue more exposure I would suggest posting it in the commercial forums since this is a commercial product. You can do this at: http://h30499.www3.hp.com/t5/Printing-and-Digital-Imaging/ct-p/bsc-412
    I hope this helps!
    R a i n b o w 7000I work on behalf of HP
    Click the “Kudos Thumbs Up" at the bottom of this post to say
    “Thanks” for helping!
    Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

  • USB Camera does not work with iChat

    Hello,
    I'm having a terrible time getting my ToUcam Pro II to work with iChat. I downloaded the iUSBcam program. That didn't work. I downloaded the program Macam, and copied the proper file into the Quicktime Library (as suggested) and that didn't work. I downloaded IOXwebcam, and got an error stating that it wouldn't run due to the fact that it didn't have the proper security settings. Sigh.
    So... what am I to do?
    I'd like to buy a webcam that does, actually, work with my 8 month old Mac Pro 4 core mac desktop, but the iSight camera is ridiculously expensive. Any other suggestions would be appreciated.
    Brad

    An X-box 360 cam will do it although not in that list.
    Anything that is USB 2.0 and marked UVC compliant or Vista Certified.
    Be Aware some Mac Keyboards do not have USB 2.0 ports.
    11:57 PM Tuesday; September 8, 2009

  • PCI USB Card Does NOT Work With Mass Storage Devices

    I have a StarTech PCI card with 6 USB 2.0 ports that I inserted in my 500 MHz (overclocked) B&W Power Mac G3. It works great for any USB device EXCEPT for any hard drive or DVD/CD-RW drive. I checked the system.log file for errors. Nothing shows up in System Profiler or Disk Utility, obviously. Here's what it consistently says:
    Dec 16 23:33:28 Geoff-Myers-Power-Mac-G3 kernel[0]: USBF: 674.997 [0xf9c000] The IOUSBFamily is having trouble enumerating a USB device that has been plugged in. It will keep retrying. (Port 6 of hub @ location: 0x62000000)
    Dec 16 23:33:33 Geoff-Myers-Power-Mac-G3 kernel[0]: USBF: 679.977 [0xf9c000] The IOUSBFamily was not able to enumerate a device.
    I'm running the latest version of Mac OS X Tiger 10.4.3. What is wrong? StarTech doesn't have a driver, but nothing should be necessary. Is there a 3rd party USB Mass Storage Device driver that might work better than the Apple generic driver? PLEASE HELP ME! I cannot live with USB 1.1.

    Some users have reported problems with certain brand cards and their controller chipsets, so trying a different card may resolve the problem. Keyspan and Macally are often mentioned as being more "Mac-friendly" than some other lessser-known brands or generic cards. Does the card have a mini-power port to supplement the power requirements? With USB 2.0, each port is on a separate bus, so a card with six ports should have one. To minimize the overall draw on the available power, I prefer to install USB cards with as few ports as are needed.

  • HP Laserjet USB Connection Does Not Work with Gigabit Airport Extreme

    I have set up my Airport Extreme Gigabit edition. It works well for wireless internet. BUT, I connected my HP Laserjet 1300 via a working USB cable, and it doesn't print properly at all. This Laserjet uses the HP Universal Drivers in Vista, which should work with the Extreme if anything should. I have set up and located the printer in Bonjour as instructed.
    With the PCL6 driver, I get one page that prints out portions of the test page text, but with most of it missing, and then a second page saying:
    PCL XL error
    Subsystem: KERNEL
    Error: UnsupportedProtocol
    Operator: 0x0
    Position: 0
    The PCL5 driver prints out "a" page, but the text comes out as solid black lines instead.
    I have tried turning the printer on and off, the router on and off, and deleting the printer and re-creating it in Bonjour, as suggested by Apple's technical support document. Nothing works. I have downloaded the latest Windows software and router firmware for this product, both of which were released recently. Same result. I also tried connecting my laptop via a Gigabit port instead of wirelessly to see if that would help. Nope.
    I have seen a few postings in other forums (not here) saying that the Airport Express (Gigabit) firmware has problems with HP printers connected via USB, which seems hard to believe given their ubiquity. If that is the case, I'd appreciate a straight answer from somebody on when it will be fixed. Some have suggested just using Ethernet, but I purchased this product (and therefore paid extra) for the USB print server, and expect to get that working.
    Thanks very much.

    I have an HP laserjet 4L with a usb adapter connected to the airport via a usb hub, and have had little trouble, except for last night it kept printing 1 partial page over and over. I printed multiple pages at once, I figured the printer just OD'd, after all its an old printer. I have one laptop that uses Vista, and its always giving me grief. Vista

Maybe you are looking for