Usb 3 Device is not responding

I'm given to understand USB 3 devices will work in a USB 2 port, however it is strangley difficult to find information about this online, and my USB 3 128gb device does not even register whatsoever in the USB 2 port on my Asus Notebook K52F/K62F. The ports do work for other devices.Was the information I was told untrue, or is there another step I need to undergo? Perhaps a driver installation?

What do you mean "the measurement failed"
Can you please provide more details.  Like an error code.

Similar Messages

  • Hi I recently dropped my ipod touch and now it wont connect to itunes. Everytime i plug it in, i get an error message saying that the usb device is not recognized

    hi I recently dropped my ipod touch and now it wont connect to itunes. Everytime i plug it in, i get an error message saying that the usb device is not recognized

    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try another cable
    - Try on another computer                            
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar                                     

  • PCI DIO 32HS (6533) Suddenly giving "The device is not responding to the first IRQ level" error, and no longer functioning.

    Greetings NI folks,
      I'm an oceanographer, and have an sidescan sonar data aquasition computer running Windows XP SP2, and NiDAQ 7.0 (Legacy). For several years, this machine has worked flawlessly, but today, I booted it up to test the system for an upcoming job, and I got some strange errors in our sonar program. I tranced the problem to our NI-6533 PCI-DIO-32HS card. I launched NI Automation Explorer to test that the card was responsive, and when I click the "test panel", I get an error: "The device is not responding to the first IRQ level." Continue (yes/no). If I click yes, I can test the digital i/o's, but nothing happens, and all the tests fail (nonresponsive). I tried moving the card to another PCI slot, tried forcing it to have a specific IRQ that was unused by anything else, and finally tried moving it to another computer that had never been used with the DIO card. I'm still getting the error, and the card is nonresponsive. I'm at the limit of my abilities, and would like to know if there's anything else I can do, or should we send the card back to NI for repair/diagnosis.
    Thanks.

    Duplicate Post
    Best Regards
    Hani R.
    Applications Engineer
    National Instruments

  • AT-MIO-16XE-50 device is not responding to the selected base address

    I'm trying to install my AT-MIO-16XE-50 DAQ board onto my Windows NT desktop computer, but I'm having trouble.
    Here's what I've done: I've installed LabView 5.1 and the NIDAQ 7.0 software onto my computer first. Then I've physically installed the DAQ board into my computer. After starting the computer, the plug-and-play system seems to recognize the new hardware and install drivers for it. It then says I need to reboot the computer, so I reboot the computer.
    When I then look at my device manager, it lists AT-MIO-16XE-50 twice. Under the properties/resources tab, one of them lists "input/output range", "interrupt request", "direct memory access", and "direct memory access" (i.e., 2 "direct memory access"s). The second one only lists "direct memory access" once and nothing else under the properties/resources tab. Also, the first one says that it is working properly while the second one says that it is not working properly (Code 10). I've played around with chaging the "direct
    memory access" numbers and after rebooting the computer have gotten both AT-MIO-16XE-50's in the device manager to say that they're working properly. So, now the DAQ board appears to be installed correctly, because the device manager reports no problems with it. However, there are still 2 of them. My first question is this: should there be only 1 entry in the device manager list, or are there supposed to be the 2 that I see? The entries do appear to be different from each other, but they're for the same device, so that's a little confusing.
    When I open my Measurement and Automation explorer, only one AT-MIO-16XE-50 device is listed (so this looks good), and under "properties" all 3 "direct memory access" numbers are listed. So, this all seems good. But, when I click on "test resources" or "test panel", I get an error message saying that "the device is not responding to the selected base address". Considering that this device was plug-and-play, and I did not set the base address manually, I don't understand why I'm getting this error message.
    What I've tried is to change the "input/output range" number by using the device manager. I've tried a few different settings (rebooting the computer after each change) and none of the different "input/output range" settings seem to work.
    I'd appreciate it if you could give me any help on figuring out how to resolve this "not responding to base address" problem. The info on your web site
    appears to suggest flipping dip-switches on the DAQ card, but my card does not have any dip switches because it is plug-and-play. So, right now I'm
    clueless! Thanks for reading this, and I hope that you have more insight than I do.

    Smaria,
    The AT-MIO-16XE-50 shows up twice in the Device Manager because it reserves three DMA channels, and the ISA bus only allows two DMA channels per ISA slot. You mentioned that you were able to get both devices working properly in the Device Manager. Below is a link to a KnowledgeBase that describes the proper procedure to successfully accomplish this. You should verify that this is the procedure you followed:
    Exclamation Mark Appears with Error Code 10 on Windows XP/2000/98 After Installing AT-MIO-16E-10
    Spencer S.

  • MTP USB Device did not install

    New PC, Windows 7, Office 2010, My Blackberry desktop software does not see my 9530 Storm  I've downloaded new desktop software, but keep getting an error that my MTP USB device did not install when I connect my 9530 to the USB Port.

    BACK UP YOUR REGISTRY!!! Editing the registry can be (read: IS) dangerous and can cause no end of pain if done incorrectly.
    - To Back Up your Registry: Click START menu and click RUN. Type REGEDIT. Click File, then choose Export and type a name for the Registry Backup, something like REGBACKUP012015 or whatever works for you.
    - Click Export and let it export the registry to a file.
    - To fix the issue: Follow the folder tree on the left to: HKeyLocalMachine > System > Current Control Set > Control > Class
    - Find {EEC5AD98-8080-425F-922A-DABF3DE3F69A} down the LEFT hand side and click on it.
    - Under the list on the RIGHT hand side find UpperFilters
    - Right-Click UpperFilters and click Delete
    - Close the registry editor and restart your PC (without the iphone attached).
    - Once restarted and logged back in, plug in your iphone and voila!  Windows will actually choose the correct driver.

  • If my device does not respond in MAX does it mean it is damaged?

    I was using an example vi to acquire digital data, however the output LEDs on the vi front panel started to show random results.  So I closed the vi down and tried again but nothing happened at all?  So I went to check acquisition in MAX and the following error message was displayed:
    The device is not responding to the first IRQ level.
    Does this mean I have damaged the PCI card?  If it does,  will it cost a lot to get fixed and how long will it take to get it back in working order as I have to complete my labview project by early december.
    cheers

    Hi Hannah
    I'm using PCI-6034.  I was able to acquire data in MAX and LabView vi's for the last couple of months so I am presuming that it must have been set-up correctly, although I could be wrong.  I am also concerned by the fact that I could smell a hint of burning coming from the PC when I was performing the last acqusition before MAX could no longer acess the card. 
    I am guessing that this means the card is fried?  Can it be repaired or will it have to be replaced?
    cheers  

  • The device is not responding to the first IRQ level

    I am using a DAQCard 700 with a NIDAQ 6.9.3 driver on a windows XP. When I install the card and run the configuration uitillity (MAX) and push the test resources button, the computer hangs and responds to no input (not even ctrl-alt-del). When I push out the PCMCIA card the error message: The device is not responding to the first IRQ level. Anybody that has an answer?

    Hi PhilV,
    It looks like you had an old AT board in a computer and then the power supply went out and you evidently also changed computers to a device with Windows NT.  Now that you're in the new computer there appears to be some sort of IRQ conflict that is preventing the board from working.
    In the past when I've seen this issue and all of the proper steps have been taken to troubleshoot it, the problem is often that the board died between the last use and the current use.  However, it's not always the case, so here are a few other options.
    First make sure that you have Traditional DAQ 7.4.1 (if you have LabVIEW 7.0-8.0 or are doing text-based programming) or Traditional DAQ 6.9.3 (if you are using LabVIEW 5-6.1).  Then make sure that you followed the installation procedure outlined here: Product Manual: AT E Series User Manual (Chapter 2)
    I did a quick search on ni.com for "device not respond base address" and "irq isa" and found some of the following KnowledgeBases and links that should help you properly troubleshoot the device.
    "Not Responding to the Selected Base Address" Error
    Troubleshooting Plug and Play Devices for Windows NT 4.0
    My PC Doesn't Have Enough Interrupt (IRQ) and DMA Channels to Support the Hardware I Want to Install
    There have been a lot of advances in DAQ boards since the old AT days, so with newer devices and computers issues like this are rarely seen.  Hopefully though, the device you have is not broken and we will be able to find out what is wrong with it right now.
    Regards,
    Otis
    Training and Certification
    Product Support Engineer
    National Instruments

  • I have a new Nano and I get a message that says the USB device is not recognized by my computer and I cannot set it up.

    I have a new IPod Nano and when trying to connect to my PC for the first time I get a fault message that says the "USB Device is not recognized by my computer. I have several other IPod devices and have never had this problem. When I go to windows explorer, the device does not show at all, so I cannot manually open it.

    Hello JETaylor2015,
    Congratulations on your new iPod nano!  I would be concerned too if my iPod was not recognized by iTunes or my computer.  I recommend reviewing this article for steps to take when your iPod is not recognized:
    iPod not appearing in iTunes
    http://support.apple.com/kb/TS3716
    Thank you for using Apple Support Communities.
    Best,
    Sheila M.

  • The device PCI 6036E: Analog Input error:"the device is not responding to the base address",Output :No signal

    I am using PCI 6036E DAQ card, DAQ 6.9.2. , I have not connected to any external device.
    When I tested card(in Test Panel of MAX2.2,DAQ 6.9.2) an error appearing �the device is not responding to the base address� � then I pressed Yes, Then TestPanel window appearing�
    In analog Input Tag, there is an error �-10805�. This error also appearing when I run the standard analog input samples (use Delphi 6.0).
    I tested analog output functions in TestPanel, Delphi Examples, LabView 6.1. There are not error appearing but there is not output signal (using Oscilloscope to see).
    Output, Input digital functions are working correctly.
    Next I try to foll
    ow all the instruntions as recommended:
    -Changing TO another slots PCI
    -Reinstall Os WinXP,98SE�
    -Use another Computer�
    But all of the cases are still not working.(the above error still appeared, no output signal)

    Nvd,
    I'm sorry to hear about the problems that you are running into with your DAQCard. I can understand your frustration with the errors that you are seeing. You mention that you have tried to do some troubleshooting, I was wondering if you have tried all the troubleshooting techniques listed in this KnowledgeBase:
    http://digital.ni.com/public.nsf/websearch/DCFCDB240788F8D486256D6A00834D80?OpenDocument
    If you have tried all of those things, I would suggest one additional thing to try. I would suggest updating your NI-DAQ drivers to version 7.0. These drivers are the newest versions of our Data Acquisition Drivers, and can be downloaded from our website here:
    http://digital.ni.com/softlib.nsf/webcategories/85256410006C055586256BBB002C128D?OpenDocument&
    node=132060_US
    If you have tried all of the above troubleshooting options, please post a detailed description of what you have tried. This may help to clarify what is going wrong.
    Jed R.
    Applications Engineer
    National Instruments

  • " device does not respond to is base address, do you want to continue ?" OR " Le périphérique ne répond pas à l'adresse de base"

    Environment :
    NI-DAQ 6.9.3
    PCI-6025 E Card
    LabPC1200 Card
    PCI serial interface card
    AGP video Card
    Measurement & Automation explorer 2.0
    After using the PCI-6025 E during an hour with the Measurement & Automation explorer 2.0 software, the message :�Le périphérique ne repond pas à l�adresse de base, voulez vous continuer?� or « the device does not respond to is base address, do you want to continue ? »
    All the informations , even in the System Configuration Panel, seem to be in order. It seems that the problem occurs after I have tried to use also the Lab PC 1200 by the way of the Measurement & Automation explorer 2.0.
    I have tried to:
    � restart the software,
    � stop the PC and restart it after a while,
    � uninstall NI-DAQ 6.9.3 and all NI softwares
    � Install NI-DAQ 7
    The same problem was always here.
    � stop the PC remove all the Cards except the video card
    � restart the PC
    � stop the PC and put only the PCI-6025E Card
    The same problem was always here.
    � uninstall NI-DAQ 7 and all the NI softwares
    � stop the PC and remove the PCI-6025E Card
    � Install NI-DAQ 6.9.3
    � Stop the PC and install the PCI-6025E Card in another PCI Slot.
    The same problem was always here.
    I have each time try to change the number of the card by the use of Measurement and automation explorer 2.0 but with no success.
    How can I do to use again this card?
    I really thank you for any response.
    NICOLAS Gabriel.

    Hey Nicolas,
    Try opening up the Reset Device.vi inside of LabVIEW and execute the VI. All you have to do is set the correct device number and check that the error returned is 0 and not another error number. In many cases a crashed program can cause the devices to enter into an unsafe state that they need to be reset from.
    It is possible that you damaged the device and that it will need to be sent in for repair, but in most cases a reset will fix the issue. Also, try opening up MAX and right-click on Traditional NI-DAQ Devices under Devices and Interfaces and click on reset Traditional NI-DAQ. If that doesn't work try the Device reset under DAQmx as well.
    I hope this helps out.
    Joshua P.
    National Instruments

  • HT201263 my iphone is stuck in the connecting to itunes screen, i can not restart my phone the top power button is broke? any ideas? it wont let me connect to itunes either, usb device can not be detected

    my iphone is stuck in the connecting to itunes screen, i can not restart my phone the top power button is broke? any ideas? it wont let me connect to itunes either, usb device can not be detected

    Hello Alex_boi941,
    Thanks for using Apple Support Communities.
    I'm sorry to hear that your iPhone's power button is not functioning correctly.  To be able to get full functionality of your phone, it would need to be repaired.
    Apple - Support - Service Answer Center
    http://support.apple.com/kb/index?page=servicefaq&geo=United_States&product=ipho ne
    Take care,
    Alex H.

  • Are mobile internet USB devices still not working on Snow Leopard?

    Are mobile internet USB devices still not working on Snow Leopard? I actually had to go back to my previous operating system to get this to work. I would however prefer to use Snow Leopard...if Apple & HUAWEI have finally got their act together!

    There appears to be a problem with drivers for USB wireless modems with 10.6. I upgraded from Leopard to Snow Leopard and now can't connect to the internet with my wireless modem. I hope Apple sort this out soon. Or maybe it's Huawei that needs to put a 10.6 driver into its software.

  • W520: Unable to boot from USB - device does not show up in boot menu

    I have a W520, and I am trying to boot from a USB key. The USB key is bootable, my old T61p boots just fine from it, and so does another computer I tried.
    The W520, after pressing F12 on power on, immediately shows the Intel PXE agent and then some blue boot menu, which only shows hard drive and LAN as available boot options.
    I have tried all three USB ports but the results are always the same - the USB device does not show up. Is there any trick or BIOS setting to enable boot from USB?
    Thanks,
        CS 

    Hello Neil
    Thanks for getting back to me
    The issue was that the usb drives were disabled in the bios from the  Startup menu.
    To enable
    1. Enter bios
    2. Select boot
    3. If you do not see the boot device you require use the down cursor key until the "Excluded from boot priority order" becomes visible.
    4. Select the device you require (in my case USB HDD)
    5. Save and exit.
    You can now boot from a usb stick and install the Linux distro of your choice :-)
    Cheers

  • What do I need to do to get my cannon camera to upload pictures into iPad . When I plug it in system comes up connected USB device is not supported?

    What do I need to do to get my cannon camera to upload pictures into iPad . When I plug it in system comes up connected USB device is not supported?

    Use the camera's SD card instead.
    Another way. You can use a USB flash drive & the camera connection kit.
    Plug the USB flash drive into your computer & create a new folder titled DCIM. Then put your movie/photo files into the folder. The files must have a filename with exactly 8 characters long (no spaces) plus the file extension (i.e., my-movie.mov; DSCN0164.jpg).
    Now plug the flash drive into the iPad using the camera connection kit. Open the Photos app, the movie/photo files should appear & you can import. (You can not export using the camera connection kit.)
    Secrets of the iPad Camera Connection Kit
    http://howto.cnet.com/8301-11310_39-57401068-285/secrets-of-the-ipad-camera-conn ection-kit/
     Cheers, Tom

  • HT1430 I do a hard reset of my iPhone every so often because I feel it improves performance, but Apple states 'Reset ONLY if the device is not responding'. Forget about my OCD on this, but is their any reason my Apple stresses the ONLY DO THIS if not resp

    I do a hard reset of my iPhone every so often because I feel it improves performance, but Apple states 'Reset ONLY if the device is not responding'. Forget about my OCD on this, but is their any reason my Apple stresses the ONLY DO THIS if not responding?

    deggie wrote:
    Because it is more far-reaching than just turning the phone off and back on, it completely takes out anything in volatile memory, etc. I do reset mine if I notice problems such as no email coming in, text message issues, etc. but the same thing could probably be accomplished by just turning the phone off and on in your case.
    Thanks deggie, I think I get it now. Volatile memory (I had to look it up!) is memory that is lost on loss of power, so it's as you say... I'm not achieving anything on a normally functioning iPhone as on-off achieves the same result!... Thanks

  • Hi guys,whenever I try to upload music on to my iPad,it's telling me that the device is not responding,are it has been disconnected

    Hi guys,whenever I try to upload my music on to my iPad,it's telling me that the device is not responding,are it has been disconnected,can any one help me thanks

    10.5 is NOT software for your ipad.  It is the itunes software for your computer.

Maybe you are looking for

  • IPod touch aps open and close on their own and iTunes player starts up

    I have done four complete wipes and re-installs and aps are continuing to open and close at random even if iPod touch isn't being used. Random tracks begin playing while screen is locked and aps open and close randomly throughout. I've completely wip

  • FI HELP TCODE: FBL5N

    Hello Friends. Let me give u a brief what is to be done. Run transaction FBL5N for any customer and company code: Next screen will be 'Customer Line Item Display' Double Click on any line item , Click on Header button--- Next screen is Document Heade

  • Slow bootup and kernel panic on every shutdown

    2.8GHz Core 2 Duo - Mid 2009 4GB Ram 10.5.8 / 10.6.8 Computer takes about 10 minutes to start up, once it is up it runs noramlly. When I go to shutdown, i get a slow window shade effect followed by a kernel panic message. This process runs like clock

  • Light room Modules

    why do i keep getting this message "An error occurred when attempting to change modules.

  • Needed all the details about BC SETS

    HI, THIS IS BALAJI.T AND MY EMAIL ID IS [email protected] WHAT DO U MEAN BY "BPIA".  THEN IF YOU KNOW ABOUT THIS ALSO YOU CAN SEND TO MY EMAIL ID.  PLZ.......... I NEED ALL THE INFORMATION RELATED TO BC SETS AND IF IT IS ALREADY AVAILABLE IN ECC 6.0