Usb (#3) not longer working?

Regardless of what device I plug into the third usb port, nothing seems to work. I just want to make sure I didn't miss something and maybe disable or turn it off. All other ports are working normal. I'm running Lion and Windows 7 in Boot Camp and the port is inactive in both.
Any suggestions would be appreciated.

Reset the SMC > Resetting the System Management Controller (SMC)
1. Shut down the computer.
2. Unplug the computer's power cord.
3. Wait fifteen seconds. a few minutes.
4. Attach the computer's power cord.
5. Wait five seconds, then press the power button to turn on the computer.

Similar Messages

I installed iousb family log release osx 10.5.6 and installed on my mac osx 10.5.8. I am trying to log and rfid reader on the usb. Sadly on restart the usb is no longer working. Happily Windows is still running OK. Is there a way 2 get my usb back?

I installed IOUSB family log release osx 10.5.6 on my mac osx 10.5.8. I am trying to log an rfid reader on the usb. Sadly on restart the usb is no longer working. Happily Windows is still running OK. Is there a way to get my usb back working? And is there a way to navigate in Windows to the file I installed and remove it? Any help appreciated.

BDAqua wrote: Does OSX boot at all, or not?
Yes, it does. Right to where I am supposed to log in, but since the USB is not working (either mouse or keyboard), I'm stuck. I have to shut down and restart and boot into windows.

After software update usb mouse no longer works.

After software update Microsoft usb mouse no longer works. System Profiler "sees" usb mouse. I took my macbook to the Genius Bar at Apple and they were not able to help. Pretty lame....

any ideas on how to solva this?

Apple USB modem no longer works with Mountain Lion

Now that I've upgraded my iMac to Mountain Lion my Apple USB modem no longer works. Does anyone know of a software fix or have I just lost my faxing ability with this item and have to buy something else?

That's a very sad situation as the Official statement link above (http://support.apple.com/kb/ht3152) states that the modem cannot be used with any Windows. So Apple thinks that people investing in the ability to Fax and relying in Apple's good product only deserves to throw out their modems (because now it is useless on any platform)...

Existing Apple ID is not longer working with Face Time and Message on the iPhone after iOS 6

After the IOS 6 update on my iPhone the Apple ID is not longer working with Face Time and Message. Each time I try to log in I receive the message that the password or the user is not right. But they are, because on all other devices and all other parts of the iPhone (iCloud, AppStore, iTunes) they are working. Other Apple IDs are working fine.
What's wrong? Any idea?
Thanks

Blue
It sounds like you restored from an old back-up. Did you back-up just before your software update? It will use your last one and if your last back-up was a ywear old then it will use that one.
In general, if you are getting these messages on your iPhones select logout (when you get that Apple Id request) and then log back in with your newer ID.
Sorry for your losses.
Cheers

PhotoshopCS6 file is not longer working, error message reads unreadable

PhotoshopCS6 file is not longer working, error message reads unreadable. PLEASE HELP!!!!!! I've spent so many hours, the copied that I do have are in JPEG. and PNG and they arnt as clear.

And what exactly? You have neitehr provided proper system info nor the exact error message nor told us anything about your documents. If you are referring to PSD files suddenly registering as damaged, you might wanna check the forum. This has been discussed quite a bit. and of course you might want to read some primer on the big Internet why people use versioning/ incremental saves and backups to avoid critical files being lost...
Mylenium

App download and up dates are not longer working

Since two days the up date and download of apps is not longer working on my iPad

SELECT from SQL (Sql Manager) gives f.ex. "2010-11-27 00:00:00
Similar SELECT from the old ACCDB, linked to a MDB (query in ACCDB) gives "27-11-2010"
Similar select in new ACCDB, linked to SQL (query in ACCDB) gives "2010-11-27 00:00:00"
In linked table in new ACCDB the date is "2010-11-27 00:00:00"
In linked table in old ACCDB the date is "27-11-2010"
In form in new ACCDB is date seen as "2011-11-27 00:00:00"
When I do a AddNew (by VBA-code) the field change into "16-02-2011" and error while trying to update (wrong date format, I guess)
The update in this case is done by f.ex. doing a "DoCmd.GoToRecord , , acPrevious", which gives error code 2105 "You can't go to the specified record."
Another way that worked before is to go to another record by using a value from a Find-Record-form and do a "DoCmd.FindRecord <newrecordname>". This gives error 3146 "ODBC--call failed. [Microsoft][ODBC SQL Server Driver][SQL Server]Conversion failed
when converting date and/or time from character string. (#241)". Other functions (filling in other values in the form, based on a chosen name f.ex. is working, - but the record is never written to the Table).
In form in old ACCDB the date is seen as "27-11-2010"
When I do a AddNew (by VBA-code) the field change into "16-02-2011" and update and everytrhing is fine
Another way (than the AddNew) the date is created/changed is by using VBA "[datefield] = Date". The datefield is set to f.ex. "16-02-2011" (where old value could be "2010-11-27 00:00:00"), - and the same problems as described above is present.
Only way to "escape" is to click the ESC-key, to cancel all changes of the record in focus.
I hope this clarify, and I am at your disposal for further investigations any time ;-) almost 24/7, sigh...
Sune

After updating my 3GS with ios5, my BMW usb interface no longer works

After updating my iPhone 3gs with ios 5, my BMW usb interface no longer works. I can no longer see my music on the screen and cannot control my music. I tried my old Nano in my car and that works so I'm thinking it must be something with ios 5. Any suggestions?

Update: I was able to resolve the problem by re-syncing the music on my iPhone in iTunes and then shutting down the phone and restarting it. After that, I connected the usb cable from my car to the phone and it worked.

USB device no longer works after 10.6.5 patch

After installing the patch for 10.6.5 Thursday, my Belkin N52te no longer works. It has previously worked fine, and the system extension for it was able to see it, but now it says "No device connected". I have tried re-installing the driver, and 75% through the installation I get a message that the xxx.kext file was not installed correctly. I get this each time I attempt to re-install it.
This gamepad has worked flawlessly for me since purchase in spring of '09 prior to this.
Please don't tell me to update the driver, as Belkin's "latest" is Feb 09. I have contacted Belkin, and am waiting for a response.
I found a suggestion of finding the old usb.kext file from the system backup I have on a second drive, and replacing the current one with it. If anyone thinks this will work, could they give me the exact name of the file to look for?
It seems odd that Apple, after trying to get the Mac accepted as a viable gaming machine, should put out a patch that breaks one of the most widely used "speedpads" on the market. I have been an avid World of Warcraft player for close to 6 years now. The enjoyment I receive while playing WoW has been the driving reason for me to purchase 2 top of the line Mac Pro's in the past 4 years. Come on Apple, fix this, please!?
Thanks,
Dan K.

February 2009? Snow Leopard wasn't even out yet. It is lucky it has worked for a year and a half.
Come on Apple, fix this, please!?
This is a user to user board. Check the terms of use, if you don't believe me. If you want Apple to fix something, here are the links:
http://www.apple.com/feedback/
http://bugreporter.apple.com/
I found a suggestion of finding the old usb.kext file from the system backup I have on a second drive, and replacing the current one with it. If anyone thinks this will work, could they give me the exact name of the file to look for?
While this may work, that's a jalopy of a solution. It might break in the next update, not being up to date itself, and some other extension might be dependent on it. Best to downgrade until you can get assurance that it will work with 10.6.5, if this is an important feature for you. You can either recover your backup, or if not available, see this tip:
http://discussions.apple.com/thread.jspa?threadID=1308817&tstart=10

[SOLVED] USB 3G no longer works after upgrade to GNOME 3.8

I did the 'big' update today, including upgrading to GNOME 3.8. Unfortunately, NetworkManager no longer picks up my 3G USB modem (which used to work fine before the update). Any pointers as to how I could debug this would be greatly appreciated.
wvdial has never really worked for me, but gnome networkmanager used to pick up my device and the connection, and now simply acts as if it's no longer present. Attempting to follow the instructions on the wiki to re-setup my USB stick (the instructions I followed in the first place) no longer works. Did today's update cause the same problem for anybody else?
**Update: After updating today to modemmanager 0.7.990-4 and running
sudo systemctl enable ModemManager
sudo systemctl start ModemManager
I have full connectivity again with the built-in DW5550 mobile broadband card in my Dell Precision M6600 (including showing signal strength in the GNOME 3.8 top bar, etc). Thanks all for the help, and (most importantly) to whoever fixed up modemmanager!
Last edited by dawid.loubser (2013-04-26 16:57:42)

wvdial might also be a workaround, if one does not like to downgrade. In my case, I had to unset my PIN on the SIM card first. One can do that using a mobile phone, for example.
Then
# pacman -S wvdial
in /etc/wvdial.conf, I put
[Dialer Defaults]
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
Modem Type = Analog Modem
ISDN = 0
Stupid Mode = 1
Dial Attempts = 3
Init1 = ATZ
[Dialer huawei]
Modem = /dev/serial/by-id/usb-ZTE_Incorporated_1_1_Surf-stick_MF19001MOD010000-if02-port0
Baud = 115200
[Dialer voda]
Init3 = AT+CGDCONT=1,"IP","web.vodafone.de"
[Dialer dial]
Phone=*99**1#
Username = umts
Password = umts
You can find out your modem name by looking it up with
ls /dev/serial/by-id/
In my case there were names containing the strings if00, if01 and if02, and if02 turned out to be the correct one. This depends on hardware.
Also, in the "Init 3" line, you may have to replace "web.vodafone.de" according to your provider. The section "dial" seems to be quite universal from what I read on the web, so you may not have to change that.
then
# wvdial huawei voda dial
and hope for the best.
Disclaimer: I do not have a comprehensive understanding of what I did here, but it worked in my case and it might work for you, too.
I noticed that the Defaults section makes a difference, because the one I just edited in above avoids some delay in dialing.
Last edited by tobi-fankhaenel (2013-04-23 08:23:00)

Upgraded to Snow Leopard and USB ports no longer work completely

Hi!
So my wife is using my older (from 2007) 15in macbook pro. We just installed Snow Leopard (from Tiger) and the USB ports are no longer functioning correctly.
Previously, intermittently (between restarts) one of the USB ports wouldn't work well, but restarts always fixed it. This would happen maybe once or twice a month.
Currently, neither the left or right USB port work well. Both will run a USB mouse and charge an iphone, but neither will recognize the phone or a card reader as plugged in.
We've tried restarting. Tried turning off, unplugging, removing the battery and holding down the power for 5 seconds and restarting.
Nothing is working. Does anyone have any tips on how to fix it?
(The iphone is recognized by my macbook pro, so it's not the wire or the phone, at least as far as we can tell.)
Thank you kindly in advance.

I think it's time you upgraded to a newer version of Photoshop.

USB ports no longer working after 10.4.7 update

Hi, I ran the latest update (10.4.7) on my machine which is a G4 Quicksilver PowerPC. I have an Apple 17 inch flat screen display that has two USB ports attached. I had my keyboard plugged into one of the USB ports on my flat screen. After the update both USB ports on the flat panel no longer work! I can use the USB ports directly off the G4 itself and it works fine. Has anyone seen this issue? I guess I am stuck now until Apple decides to fix this?
Thanks,
Rob

In my experience, the USB ports on the back of an Apple monitor can be re-enabled simply by unplugging and plugging back in the device in question. You might also check to see that the USB Monitor hub shows up in System Profiler. My Apple monitor USB ports experienced no changes in moving to 10.4.7.
bd

USB ports no longer working on EliteBook 8560W

I have an EliteBook 8560W notebook running Windows 7 SP1 64-bit. My friendly IT department was trying to fix a webcam driver, installed various sdriver and system updates, and ended up giving it back to me in worse condition than when I gave it to them.
The current state is that the ports on the right side (USB 3.0) both work, but the ports on the left side (USB 2.0) do not, nor do the ports on the dock.
Another point of data is that in the Device Manager, there are two "Unknown Devices" with the same ID: USB\VID_8087&PID_0024&REV_0000
I've tried various combinations of reinstalling drivers as recommended by various websites I've found, but nothing has worked.
Any suggestions?
Thanks!

mek363 wrote:
I've tried various combinations of reinstalling drivers as recommended by various websites I've found, but nothing has worked.
Any suggestions?
Thanks!
This is not advised....you should use your P/N and look on the HP driver site to find the right drivers for your laptop.
HP Support - Software & Drivers
I am a Volunteer to help others on here-not a HP employee.
Replies aren't online 24/7 because of Time Zone differences.
Remember in this Day and Age of Computing the Internet is Knowledge at your fingertips if you choose understand it. -2015-

USB Mic no longer works with Skype after 7.1 updat...

Using a USB headset with skype, worked with previous versions, works with other programs. I can hear people talk but they can't hear me! Skype detects the mic just fine but when I talk nobody can hear me.
I have tried updating drivers, re-installing skype, I have tried deleting my profile/preferences from the skype folder on my PC and starting from scratch, tried restarting my computer, re-installing my headset drivers, and tried restarting or re-plugging in my mic. Nothing works. Skype simply doesn't use my mic properly in the new version, previous versions did not have this problem, as I said mic works fine in all other programs.

Hi pa.elimination, Can you please reproduce the issue and provide logs as described in this link https://support.skype.com/en/faq/FA12321/how-do-i-create-log-files under Skype for Windows Desktop and attach it to your post?
This will help us investigate and solve the problem you are experiencing.
Can you also try with the 7.0 version to see if that version solves your issue?
http://download.skype.com/msi/SkypeSetup_7.0.0.105.msi
Thank you

Mail search using e-mail addresses not longer works after 10.6 update?

I just updated to 10.6 from 10.5. I have also added all the software updates.
The search function no longer works for e-mail addresses. I used to right-click on an address, copy and paste in search. Now, when I do that, it lists like this : NAME <[email protected]> (sample info) instead of just the e-mail address. In this new form, the search function no longer functions. Is there a way to revert to the old way mail copies e-mail address?
I do not want to have to delet ethe name & out of each paste.
input greatly appreciated!

Perfect! Works like a charm.
For others looking for the fix.
In 10.6, it seems someone at Apple decided that Copy Address should really mean Copy Name And Address And Add Angle Brackets Around The Address, because that's exactly what happens when you use Copy Address in Snow Leopard's Mail app. Instead of getting [email protected] on the clipboard, you get Sue Sample <[email protected]>.
Besides now having an incorrect name on the Copy Address contextual menu item (thought admittedly, the alternative is a bit lengthy), this behavior is incredibly irritating if you want only the email address on the clipboard. Thankfully, some engineer somewhere deep within Apple included a hidden preference to change this behavior -- and the fine folks at Mac Daddy World (the Ecamm Network blog site) dug deep and discovered this preference.
To revert to the 10.5-style behavior in Mail, first quit Mail then enter this command in Terminal:
defaults write com.apple.mail AddressesIncludeNameOnPasteboard -bool NO

Usb (#3) not longer working?

Similar Messages

Maybe you are looking for