Usb 6009:connecting the sensor and motor

Hi there,
I am new to the labview also the usb-6009. I want to know if I can connect my sensor to the device. The output of the sensor is either analog voltage, pulse width or serial.If I want to use the AN pin, can I just connect the wire to the ADC from the usb or I need to add some circuit before connect it to the usb?also, if I want to control the brushless dc motor with the driver, can I just connect the wire from the motor driver direct to the device? How to connect it?
Thanks

You can connect analog voltages directly to the USB-6009 to be measured as long as they do not exceed the input limits (-10V to +10V).
Connecting the motor directly to the outputs is a bad idea.
Digital output is 0-5V, 8.5mA
Analog output is 0-5V, 5mA
So unless your motor draws less than 5mA (extremely unlikely) you'll blow up your DAQ!
You will need to buffer the outputs somehow unless you are just driving logic gates.
It's all on the datasheet... http://www.ni.com/pdf/products/us/20043762301101dlr.pdf
Message Edited by Troy K on 06-06-2008 02:36 PM
Troy
CLDEach snowflake in an avalanche pleads not guilty. - Stanislaw J. Lec
I haven't failed, I've found 10,000 ways that don't work - Thomas Edison
Beware of the man who won't be bothered with details. - William Feather
The greatest of faults is to be conscious of none. - Thomas Carlyle

Similar Messages

I tried to restore my iPod Touch 2nd generation and now it won't sync to itunes. on the screen it shows the usb end of the cord and the iTunes logo over it. Is it broken?

I tried to restore my ipod touch 2nd generation and now it won't sync to itunes. On the screen is the USB end of the cord and the iTunes logo over it.
I have turned it off and on, held the off button down and the select button down but it still comes up with that picture on the screen. Have I broken it?
Please help.
Mimi

It means the device is in recovery mode. You'll need to reconnect it to iTunes and restore it again.
You may need to connect it in recovery mode manually using the instructions in this Apple support document.
iOS: Unable to update or restore
B-rock

I have a Sony radio in my car. With IOS 4 on my IPhone I could use the docking plug to the usb input on the radio and stream ESPN radio or pandora to the radio. After upgrading to IOS 5 on the phone the Sony radio will not recognize the phone . Any t

I have a Sony radio in my car. With IOS 4 on my IPhone I could use the docking plug to the usb input on the radio and stream ESPN radio or pandora to the radio. After upgrading to IOS 5 on the phone the Sony radio will not recognize the phone . Any thoughts.

I am reading on this site about the error I am getting and it wants me to change some files that I am not comfortable messing with. Mainly because it is like a foreign language. Will the store do this for me or tell me if it is neccessary?

I have connected the adapter and cable from imac to GVA HD tv but nothing seems to be happening.

I have connected the adapter and cable from imac to GVA HD tv but nothing seems to be happening. Any suggestions?

Was that message showing a s dialog when selecting the tv connection as a sound output device? I ask because I don't know the exact context of that message and never heard of it before.
It may be helpful to take a screen shot of both that message and also the list of the sound output devices while the tv is connected.
You never specified your model (year) of your imac so I don't know its limitations. Maybe some version doesn't support sound through the mini-displayport (hard to believe any model wouldn't with mini-displayport). But if that is the case you may have to resort to analog stereo from you stereo line out output jack to your tv.
One final thing. The mini-displayport adapter you have may not support audio. That was a possibility a few years ago. That is why most places that sells these things also explicity specify whether the adapter supports audio. For example, monoprice's adapter:
Mini DisplayPort | Thunderbolt® to HDMI® Adapter w/ Audio Support
or even the Moshi adapter sold through the apple store.
Moshi Mini DP to HDMI Adapter with Audio Support
Note both these adapters explictily say they have audio support.

I have ipod touch 4th generation and i face problem as i connect the handsfree and i haveto adjust it for proper sound so somebody guide

i have ipod touch 4th generation and i face problem as i connect the handsfree and i haveto adjust it for proper sound so somebody guide

See:
iOS: Device not recognized in iTunes for Windows
I would start with:
Removing and Reinstalling iTunes, QuickTime, and other software components for Windows XP

I had 5 videos that I could see in videos apps. But after your last OS update I can't find them on my iPhone. I can see them on the pc in itune when I connect the iPhone and go to videos directory.

I had 5 videos that I could see in videos apps. But after your last OS update I can't find them on my iPhone. I can see them on the pc in itune when I connect the iPhone and go to videos directory.

When syncing, check the Movies/TV Shows Tab in the iPhone menu, and make sure ALL movies are synced (or select the ones you want to sync)

HT4437 I've bought an airbook and apple tv. I'm trying to connect the pc and my home tv. I've installed apple tv on my tv. What do I now have to do to be able to see my pc screen on the tv screen ? thanks - Bob

I've bought an airbook and apple tv. I'm trying to connect the pc and my home tv. I've installed apple tv on my tv. What do I now have to do to be able to see my pc screen on the tv screen ? thanks - Bob

Bob,
Just to confirm you have a macbook air right? If so and it is mid 2011 or later running OS X 10.8 Mountain Lion or newer you can mirror it. If home sharing is on and ATV and MBA are on same id and network you should get the airplay icon near the clock on the mac and that should mirror your screen.
If you have an older mac or pc a third party app called airparrot can do it for you.
Jules

Problems with "Background Eraser Tool" and "Blur". The tools don't affect the whole area but just connect the start and the last points.

Hello!
I have some issues with Photoshop CC 2014. The tools "Background Eraser Tool" and "Blur" won't work correctly. When I’m holding down the left mouse button and trying to erase or blur some area, the tools don’t affect the whole area but just connect the start and the last points – like drawing a line. These troubles exist with mentioned tools only, other tools work correctly.
I’ve restored each tool separately, restored all the tools together, installed new drivers for tablet, re-installed Photoshop and even Windows. Nothing helped. These tools worked correctly earlier with the same adjustments, but one day something went wrong.
How can I make the tools work correctly?
Some information about my computer:
• Notebook Lenovo Y560
• Windows 7 Home Basic SP1 x64
• Intel Core i5 2.53 GHz
• 4Gb RAM
• ATI Mobility Radeon HD 5730 1Gb
• Tablet Wacom Bamboo CTL-470

Hi,
I have a similar problem with the Background Eraser tool as well. It's the same both on my PC and on my laptop, both running Win 8.1 and PS CC2014. Would be great to have a solution for this. Did you managed to find a fix?

HT1766 i have backed up my iphone 5 and have a 5s I want to set up from that backup file. I have gone through the process once, and when I next connect the new AND the old phone to the mac and open itunes, restore or create new phone comes up not synch??

i have backed up my iphone 5 and have a 5s I want to set up from that backup file. I have gone through the process once, and when I next connect the new AND the old phone to the mac and open itunes, restore or create new phone comes up not synch?? Tried starting the whole process over once but same result. Seems not to recognise the phone and just synch as it should. Help?

Hello CosK,
The following guide can step you through the process of using a backup of your iPhone 5 to transfer your content to your iPhone 5s.
Transfer content from an iPhone, iPad, or iPod touch to a new device
http://support.apple.com/kb/HT2109
Should one or both of your phones fail to appear in iTunes, the following article provides troublesooting steps that can assist.
iOS: Device not recognized in iTunes for Windows
http://support.apple.com/kb/TS1538
Cheers,
Allen

HT1766 I have an I phone 4S and I usually back it up threw I Cloud but since my phone is pretty old and has been shutting off on me I decided to back it up in I tunes. I connected the phone and clicked Back Up Now. When it was done I picked up the phone

I have an I phone 4S and I usually back it up threw I Cloud but since my phone is pretty old and has been shutting off on me I decided to back it up in I tunes. I connected the phone and clicked Back Up Now. When it was done I picked up the phone and tried to open an app and discovered that all of my apps have been restored as if I had just down loaded them from the app store. So I lost all progress on them. Is there anything I can do to change it back? And I don't understand what I did wrong.

This means the iPhone has not been connected or synced with your computer since the passcode lock was enabled on the iPhone and too late now.

If there is no driver for iphone S4, how do I connect the phone and PC?

If there is no driver for iphone S4, how do I connect the phone and PC?

With the special cable that came with the phone. You must install iTunes on your PC in order to access the phone, sync it, and back it up.

Arctic Silver between the sensor and the bottom of the CPU

"Temp sensor inside the Socket is flat, it offer some resistance, applying some Arctic Silver between the sensor and the bottom of the CPU will increase accuracy of the obtained temperatures."
I read this information at http://www.madshrimps.be/?action=getarticle&number=2&artpage=879&articID=216
Is it correct?

dont forget, the bottom of your processor is also full of resistors. Flooding them in *CONDUCTIVE* grease maybe more than what you are asking for.
The Temp sensor in the socket is usually correct enough for static temperatures, but suck to track quick changes.
Moreover, the embedded sensor is here for a reason

HT1212 my niece has locked herself out of her ipod touch. when i plug the usb cord into the ipod and the computer, the ipod says ipod is disabled connect to itunes. itunes has a message on the computer sayiing i need to wnter in the passcode. im not able

my niece has locked herself out of her ipod touch. when i plug it into the computer with the usb cable, a message on itunes says i have to enter her passcode. her ipod will not allow me to do so. what next??

Disabled
Place the iOS device in Recovery Mode and then connect to your computer and restore via iTunes. The iPod will be erased.
iOS: Wrong passcode results in red disabled screen
If recovery mode does not work try DFU mode.
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
For how to restore:
iTunes: Restoring iOS software
To restore from backup see:
iOS: How to back up
If you restore from iCloud backup the apps will be automatically downloaded. If you restore from iTunes backup the apps and music have to be in the iTunes library since synced media like apps and music are not included in the backup of the iOS device that iTunes makes.
You can redownload most iTunes purchases by:
Downloading past purchases from the App Store, iBookstore, and iTunes Store

My iPad 4 is stuck on the connect to iTunes screen. Have held the home button down while connecting the USB cable to the iPad and its not doing anything, not even showing up under my computer Please Help

IiPad is stuck in the iTunes connect screen. I have held the home button down while plugging the iPad in and still nothing. Hard reset isn't even doing anything. It's not even showing up under my computer. Please Help

Did you get a message that the iPad is disabled?
iOS: Device disabled after entering wrong passcode
http://support.apple.com/kb/ht1212
Using iPhone/iPad Recovery Mode
http://ipod.about.com/od/iphonetroubleshooting/a/Iphone-Recovery-Mode.htm
Saw this solution on another post about an iPad in a school enviroment. Might work on your iPad so you won't lose everything.
~~~~~~~~~~~~~
‘iPad is disabled’ fix without resetting using iTunes
Today I met my match with an iPad that had a passcode entered too many times, resulting in it displaying the message ‘iPad is disabled – Connect to iTunes’. This was a student iPad and since they use Notability for most of their work there was a chance that her files were not all backed up to the cloud. I really wanted to just re-activate the iPad instead of totally resetting it back to our default image.
I reached out to my PLN on Twitter and had some help from a few people through retweets and a couple of clarification tweets. I love that so many are willing to help out so quickly. Through this I also learned that I look like Lt. Riker from Star Trek (thanks @FillineMachine).
Through some trial and error (and a little sheer luck), I was able to reactivate the iPad without loosing any data. Note, this will only work on the computer it last synced with. Here’s how:
1. Configurator is useless in reactivating a locked iPad. You will only be able to completely reformat the iPad using Configurator. If that’s ok with you, go for it – otherwise don’t waste your time trying to figure it out.
2. Open iTunes with the iPad disconnected.
3. Connect the iPad to the computer and wait for it to show up in the devices section in iTunes.
4. Click on the iPad name when it appears and you will be given the option to restore a backup or setup as a new iPad (since it is locked).
5. Click ‘Setup as new iPad’ and then click restore.
6. The iPad will start backing up before it does the full restore and sync. CANCEL THE BACKUP IMMEDIATELY. You do this by clicking the small x in the status window in iTunes.
7. When the backup cancels, it immediately starts syncing – cancel this as well using the same small x in the iTunes status window.
8. The first stage in the restore process unlocks the iPad, you are basically just cancelling out the restore process as soon as it reactivates the iPad.
If done correctly, you will experience no data loss and the result will be a reactivated iPad. I have now tried this with about 5 iPads that were locked identically by students and each time it worked like a charm.
~~~~~~~~~~~~~
Try it and good luck. You have nothing more to lose if it doesn't work for you.
 Cheers, Tom

Ipod classic not connect the computer and not load, what do I do?

Help me please!

Have you tried plugging the iPod into a different USB port on your PC? Preferably a high powered USB 2.0 port on the back of your PC and not a USB port on the front or via USB hub.
With the iPod still connected to your PC, try a hard reset. To do this, press and hold both the Select (Center) and Menu buttons together long enough for the Apple logo to appear.
Otherwise, see this article for more troubleshooting suggestions.
iPod not recognized in 'My Computer' and in iTunes for Windows
B-rock

Usb 6009:connecting the sensor and motor

Similar Messages

Maybe you are looking for