Usb-6211 utilisable avec quelle version de Labview

Bonjour,
J'envisage d'acheter une carte USB-6211, mais je lis que l'on ne peut l'utiliser qu'à partir de LV 7.1.
Or ma version favorite est LV 7.0, pourquoi ne pourrait-on pas l'utiliser avec LV 7.0 ?
Résolu !
Accéder à la solution.

Bonjour,
Parceque la version de LabVIEW est liée à la version des drivers (DAQmx) pour piloter votre matériel.
La dernière version compatible de DAQmx avec LabVIEW 7.0 est la version 8.1 comme montré sur cette page :
Compatibilité entre les versions de LabVIEW et du driver NI-DAQ (Windows)
Et dans la version 8.1 de DAQmx, le périphérique USB-6211 n'est pas encore supporté (et ne devait pas exister à la sortie de ce driver).
Cordialement,
Da Helmut

Similar Messages

  • Problème avec le NI6008 sous LabVIEW (sous Linux)

    Bonjour,
    Je souhaiterai piloter la carte d'acquisition usb ni-6008 sous une machine fonctionnant sous linux à l'aide de labview. Ceci étant, j'ai installé  Ni daqmx et Ni daqmx base, et j'ai aussi changer le firmware de la carte en le switchant sur ni daqmx base, suite à des problèmes avec ni daq mx.
    Notre problème est que sous labview en lancant NI-daq mx base task configuration utility, le système plante, il se bloque aussi lorsque l'on tape les commandes de Ni-daq mx base associés à la carte, comme une acquisition de l'entrée, j'imagine qu'il y a un conflit entre la carte et le système, mais lequel?
    Le second problème est que l'on aimerait  se servir du VI " ni usb 60xx interactive controller " sous labview, mais il y a bien une heure d'installation et de compilation des parties du VI, comment peut on réduire ce temps?
    Merci de vos réponses.

    Bonjour JP,
    Ce temps de chargement est énorme et tout à fait étonnant. Pourriez-vous nous préciser quelle version de LINUX vous utilisez et quelle version des drivers DAQmx base est installée ? Ce phénomène est-il constant ?
    Une manipulation à essayer serait la "compilation massive" du VI (ctrl+shift enfoncés+cliquer sur la flèche de run) sous LabVIEW, puis une sauvegarde totale.
    Cordialement,
    BRAUD Jean-Philippe
    Field Sales Engineer - Nord et Centre France
    LabVIEW Certified Developper

  • Relation entre les versions de LabVIEW

    Bonjour,
    Je souhaiterai savoir si votre dernière version de LabVIEW (LabVIEW 2009 je crois) peut lire des VI de la version 7.1?
    Si non, jusqu'à quelle version de LabVIEW les VIs d'une version 7.1 peuvent être lus?
    Merci d'avance
    Sébastien

    Salut,
    Pour la 1ère question la réponse est Oui.
    Pou la 2ème question: avec LV 7.1 tu peux lire que les Vis compilés avec la version 7.1 et antérieur, si version très ancienne il se peut que tu rencontre des problème de compatibilité
    a+ 
    Reg

  • How to make ROD426 connected to USB-6211 work in Labview

    Hello
    I have a rotary encoder type Hadenhein ROD426 connected to a USB-6211 I/O modul.
    I need to make this work in Labview, so i can read the position for the rotary encoder by angle. I can't find anny tools in Labview that does this.
    Does annyone have anny tips?
    Gøran Steen

    Gsteen,
    There are some examples in LabVIEW's Example Finder (Help menu -> Find Examples...) that might help.  Try Hardware Input and Output -> DAQmx -> Counter Measurements -> Position.  These examples are usually a great place to start.  I looked at "Meas Angular Position-Buffered-Finite-Ext Clk.vi" which looks like it may be of help to you.  You can also limit the example finder to only find examples that pertain to your hardware (USB-6211) by configuring the "Hardware" dropdown in the lower left-hand corner of the example finder.  If you are browsing, check the "Requirements" list in the lower right-hand to see if a particular example works with your DAQ.
    -cb

  • Driver non compatible avec ma version LabVIEW

    Bonjour,
    J'ai un driver LabVIEW de la carte Amplicon PCI-215 compatible avec les versions LabVIEW 6.0, 6.1, 7.0, 8.0 mais pas avec la version que j'ai (LabVIEW 2010). Du coup je n'arrive pas à lancer le fichier Setup.exe du driver pour l'installer.
    Pouvez-vous m'aider s'il vous plait à résoudre ce problème ?
    Merci

    Bonjour Salma,
    Merci d'avoir posté sur le forum National Instruments.
    Le fait de pouvoir lancer ou non le Setup.exe de l'installeur de ton driver
    n'a rien à voir avec LabVIEW. Généralement, cela vient du fait que tu ais
    changé d'OS. Vérifie que ton driver est bien supporté sur ton OS.
    Une fois qu'il est installé il est tout à fait possible de récupérer les VIs
    d'une version antérieure de LabVIEW (8.0 par exemple) et de les mettre au bon
    endroit pour qu'ils apparaissent dans LabVIEW 2010. Un petit MassCompile sur le
    répertoire sera nécessaire.
    Benjamin R.
    R&D Software Development Manager
    http://www.fluigent.com/

  • Usb 6211 and LabView - good for IV characteristic aquisition?

    Hi there,
    I pre-emptively declare my lowest level in using LabView and all the annex tools, so my question won't result too silly.
    I need to automatically acquire the IV characteristics for 4 solar devices, so I am thinking about connecting them to the USB 6211 in order to switch from one device to another one.
    My question is: can I use a LabView Program in order to simulate the Voltage signal to apply (range c.ca -1 to +1 V), and then collect the relative current?
    If so, how??
    Many thanks in advance for any sort of help.
    Laura

    http://zone.ni.com/devzone/cda/epd/p/id/5918
    http://zone.ni.com/devzone/cda/tut/p/id/7229
    LabVIEW has a toolkit available for this.  It uses an SMU card but you could simulate that with your 6211 and a current sensing resistor.
    Using LabVIEW: 7.1.1, 8.5.1 & 2013

  • USB 6211 with 2 Encoders labVIEW Interface

    Hi,
    I am trying to use 2 encoders (780251-01) to measure shaft rotation of 2 shafts to assure that they are rotating at the same velocity.  The encoders I plan on using are 780251-01 with a NI USB 6211.  I am seeking assistance on creating a VI.  Any help would be appreciated as I am a beginner to LabVIEW.  In the futiure, I plan to implement a National Instruments load cell. ( 783212-01)

    We have a great getting started guide for setting up encoders. The following guide will walk you through creating a DAQmx virtual channel for your encoders:
    http://www.ni.com/getting-started/set-up-hardware/data-acquisition/quadrature-encoders
    If you need help implementing the virtual channel into your LabVIEW code, we have a video tutorial for that as well:
    http://www.ni.com/tutorial/5375/en/
    Daniel C.
    Applications Engineer
    National Instruments

  • Compatibilité CompactRIO et NI uSB 6211

    Bonjour à tous,
    voila je cherche à réaliser depuis peu le développement d'un pot vibrant. En naviguant sur le net et en cherchant quelques exemples je suis tombé sur un programme qui réalise exactement mes souhaits. Mais avec "compactRIO" avec un matériel donc différent du mien. Je voulais savoir s'il était aisé de pouvoir modifier ce programme afin de réaliser la commande de mon pot vibrant à l'aide de ce programme.
    Je dispose d'un boitier NI usb 6211 et d'un accélèromètre dont voici les documentations...
    Cordialement
    Pièces jointes :
    Shaker Control Source.zip ‏3005 KB
    ICP 120.pdf ‏145 KB

    Bonjour,
    Les parties sur lesquelles vous vous posez des questions sont de la programmation FPGA et ce n'est pas possible avec votre carte USB.
    Ainsi si vous tenez à garder cet exemple de code.
    Il vous faudra coder avec des foctions DAQmx (driver de votre carte DAQ). Pour ce faire, je vous invite à regarder les exemples fournis avec votre logiciel LabVIEW.
    Vous lancez LabVIEW => Aide => Recherche d'exmples => Matériel E/S => DAQmx
    Je vous invite à tester différents VIs avec votre matériel.
    De plus, je suis persuadé que vous pouvez trouver des exemples sur notre site internet : www.ni.com dans l'onglet recherche, vous tapez Daqmx et analog par exemple et vous aurez pas mal d'information. Il faudra peut être faire attention à ce que vous retourne votre accéléromètre (mV, V?) et ainsi réaliser une échelle adaptée.
    Enfin, vous pouvez aussi bien utiliser le VI express DAQ assistant.
    http://www.ni.com/white-paper/5467/en/
    Cordialement,
    Matthieu RICORD
    National Instruments France
    #adMrkt{text-align: center;font-size:11px; font-weight: bold;} #adMrkt a {text-decoration: none;} #adMrkt a:hover{font-size: 9px;} #adMrkt a span{display: none;} #adMrkt a:hover span{display: block;}
    Été de LabVIEW 2014
    12 présentations en ligne, du 30 juin au 18 juillet

  • I have LV 7.0 and purchased USB 6211 how to install NIDAQmx 8.8

    I have LV 7.0 complete version. I purchased USB 6211 Device. It come with NIDAQmx 8.8. How to install this NIDAQmx 8.8

    You can not install NIdaqMX8.8. But you may download 8.1. This link explains http://digital.ni.com/public.nsf/allkb/97D574BB1D1EEC918625708100596848
    But you are lucky your daq unit is supported by version 8.1 (daqMX)
    Besides which, my opinion is that Express VIs Carthage must be destroyed deleted
    (Sorry no Labview "brag list" so far)

  • Signal generator fo usb-6211

    Hallo, I'm in the process of generating square wave with adjustable duty cycle for my usb-6211. After searching, I find two generators available: IVI FGEN, and DAQ Assistant. The latter seems suitable to my device, but without capability of changing duty cycle. Consequently, I'd love to know whether there exists any kind of signal generator which yields up square wave with adjustable duty cycle and whether it is feasible to connect it to DAQmx Write to feed to the signal to AO0/1 of my usb-6211.
    thanks in advance,
    win2

    Hi win2,
    you are right, the DAQmx functions are what you need. The FGEN drivers are only for the hardware based function generators.
    As you mentioned that you use DAQ Assistant, I guess you use LAbVIEW (which version?) to try to produce the rectangel with adjustable duty size.
    Right? Please let me know, which version of DAQmx you have installed on your PC, too.
    Here you have two links, where you can find an example how to generate a squares with adjustable duty cycle using the analog output.
    This example, i guess, is what you want to achieve:
    http://zone.ni.com/devzone/cda/epd/p/id/5235
    It shows, how to use software timing to adjust the duty cycle.
    The second example shows, how to create a "selfmade" signal:
    http://zone.ni.com/devzone/cda/epd/p/id/1621
    If you want to send TTL signals, please keep in mind that you can use one of the four digital outputs.
    Creating a digital pulstrain allows to set the duty cycle directly.
    I hope, this helps
    regards
    Kilian

  • How to send TTL output AND acquire AI voltage data using USB-6211

    Hello,
    I am relatively new to Labview, so please bear with me.  I have a research application involving 2 pressure transducers and a high-speed camera.  I wish to acquire analog voltage data from the 2 pressure transducers.  However, at the start of the acquisition, I will need to send a single TTL output to trigger the camera.  This TTL pulse must be sent out at exactly the same time that the AI acquisition begins, in order to ensure that my 2 pressure measurements and camera images are 'synchronized' in time.
    Is this possible on the USB-6211 running with LabView 8.20?  I currently have a fairly simple LabVIEW vi that uses a software trigger to start an AI acquisition - I have attached it with hopes that it may help anyone willing to assist me.  I would prefer to be able to simply add something to it so that it will output a TTL pulse at the start of the acquisition.  
    Thank you in advance.
    Regards, Larry
    Message Edited by Larry_6211 on 12-19-2008 11:24 AM
    Attachments:
    USB6211_v1.vi ‏212 KB

    Hi All,
    I'd like to clear a few things up. First, you'll find that if you try to set the delay from ai start trigger and delay from ai sample clock to 0, you'll get an error. Due to hardware synchronization and delays, the min you can set is two. Note that when I say two, I am referring to two tick of the AI Sample clock timebase, which for most acquisitions is the 20MHz timebase. I modified a shipping example so you can play around with those delays if you want to - I find that exporting the signals and looking at them with a scope helps me visualize what is going on. The Manual has some good timing diagrams as well but it looks like you've already hit that. The defaults would give you a delay of  250ns from the start trigger - is this too high for your situation? What is an acceptable delay? I tend to think that "exactly the same time" is a measure of how precise rather than an absolute (think delays in cable length making a difference.)
    With all that in mind, I see a few options:
    Start your camera off of the AI start trigger (an internal signal) and just know it is 250 ns before your first convert. 
    Export the convert clock to use as a trigger. This assumes your camera can ignore the next set of convert clocks.
    More complicated option: Internally you have an ai start trigger, sample clock and convert clock. From your start trigger to the first convert is 250ns but if you export your convert clock you're going to get future convert clocks as well. One option would be to generate a single triggered pulse using a counter (start with the  Gen Dig Pulse-Dig Start.vi example) with the AI start trigger as the trigger for the counter, an initial delay of 250 ns, and a high time of whatever you want it to be. This should give you a singe pulse at very close to same time (on the order of path delays) as your first convert clock. 
    Hope this helps, 
    Andrew S
    MIO DAQ Product Support Engineer
    Getting Started with NI-DAQmx
    Measurement Fundamentals
    Attachments:
    Acq&Graph Voltage-Int Clk.vi ‏37 KB

  • Can you record sound using a USB 6211 and convert the data to a .wav (or other sound) file?

    Hello,
    I am trying to build a system that will use a USB 6211 to record sounds from multiple electret microphones and then save the data as a .wav file or other sound file.  I have already built my mics and hooked the mics up to the USB 6211; the DAQ device seems to do an adequate job recording the signal - I've recorded from 3 mics at a time at 11,025 Hz, although I don't know how good the signals are since I can't save them for playback after the fact, and they aren't going through my sound card. Ultimately, I would like to save the data as a multichannel audio file which I could then open in a program such as Audacity for further editing and analysis. Since Audacity can import a variety of sound files, my file format doesn't need to be .wav if another format would work better.
    Any advice would be appreciated.
    Thanks, Eric

    If you are sampling all three simultaneously, your highest frequency recordable will be (11,025/2)/3, so about 1800Hz and that will pretty coarse (traditionally digital sound recording is at 44Ks/s at the low end). As to converting to a .wav, there are functions on the "Graphics and Sound" palette for saving waveforms to a .wav file.
    Putnam
    Certified LabVIEW Developer
    Senior Test Engineer
    Currently using LV 6.1-LabVIEW 2012, RT8.5
    LabVIEW Champion

  • How to use voltage signals as input signals into USB-6211

    Hello everyone,
    I have a USB-6211 and a PDQ80A -quadrant photo detectot from thorlabs, i am trying to take three voltage signals from the PDQ80A into my PC using USB-6211 from NI. THese voltage signals are X,Y and sum (X+Y).  
    Looking forward to your reply.
    Thanks in advance,
    _Perseus 

    Technically, the question was in the title.  But of course, the answer to that is... Connect them using WIRES.   It's designed for voltage signals, just wire your cell outputs to whatever DAQ input channels you're going to read.
    Using LabVIEW: 7.1.1, 8.5.1 & 2013

  • Une bande indiquant ''Création avec la version d'essai d'Adobe Premiere Elements'' apparaît lorsque j'ouvre mes extraits vidéos... Disparaîtra-t-elle une fois que j'acheterai le logiciel?

    Bonjour,
    J'ai téléchargé sur mon MAC le mois passé la version gratuite de 30 jours d'Adobe Premiere Elements 12. Avec cette version, j'ai pu créer plusieurs extraits vidéos pour mon assistanat de recherche à l'école.
    Maintenant, la version d'essai a expiré et une bande (avec les mots: Création avec la version d'essai d'Adobe Premiere Elements) apparaît à chaque fois que je fais jouer l'un de mes extraits vidéos. Je ne pourrai pas me servir de ces extraits si cette bande ne disparaît pas... et je ne veux pas recommencer tout mon travail! Pourtant, lorsque j'utilisais la version d'essai, aucune bande n'apparaissait lorsque je faisais jouer les extraits....
    Ma question est donc la suivante: Si j'achète la version Adobe Premiere Elements 13... y a-t-il ainsi une chance que cette bande disparaisse et que je puisse à nouveau me servir de mes extraits?
    MERCI!

    saramv
    I do not believe your question has been answered if you are inquiring about how to remove the Adobe watermark from video that you have exported from the Premiere Elements tryout.
    You cannot remove the Adobe watermark from exports from the tryout, be the export a file saved to the computer hard drive or a burn to disc. Does not matter if you purchase the product later.
    You can remove the Adobe watermark from a project file (project.prel) from the tryout Premiere Elements after you purchase the program.
    When you open a project.file (project.prel) from the tryout Premiere Elements in the purchased product, there are two possibilities for removing the Adobe watermark from that project file...
    a. Go to Timeline Menu/Delete Rendered Files...click on that.
    or
    b. Let the purchased program do it for you automatically...some of us have found this to be the case.
    Please see which one works for you.
    Any questions or need clarification, please do not hesitate to ask.
    Thank you.
    ATR

  • Comment je peux récupérer une chaine de caratères d'un fichier(txt par expl) dans une ligne (spécifiée) et une colonne (aussi spécifiée) avec notre adorable software LABVIEW

    Salut à tous,
    Comment je peux récupérer une chaine de caratères d'un fichier(txt par expl) dans une ligne (spécifiée) et une colonne (aussi spécifiée) avec notre adorable software LABVIEW.
    Thx
    Nizar
    Résolu !
    Accéder à la solution.

    Si ton fichier est un fichier tableur ce qu'a dit yohann me parait le mieux. Par contre si c'est un fichier texte qui contient une chaine au format tableur (sepération avec des tabulations) il faut utiliser "lire un fichier texte" + "Convertir un chaine au format tableur en tableau" et ensuite indexer la case qui t'intéresse.
    Maintenant si tu as un simple fichier texte  et que tu veux lire un couple ligne/colonne qui désigne un caractère précis il faut utiliser "définir la position dans le fichier" en connaissant la largeur de ton fichier texte. et la tu n'as plus qu'à rentrer dans offset: indice_ligne*largeur+indice_colonne comme une vieille réminiscence du c.
    Sebastien DEVISSCHER - Nerys

Maybe you are looking for