USB-6255 OEM Connector Pinout

USB-6255 OEM を使用して入出力ボックスを作成し、動作確認を行いましたが正常に信号取得できませんでした。
"USB-622X/625X OEM User Guide"の"Connector Pinout"のBank0とBank1を逆にした配置で作り直したところ、
正常に動作するようになりました。
このマニュアルの記載が間違っているということはありませんか？
解決済！
解決策の投稿を見る。
添付:
USB6255OEM_ConnectorPinout.JPG ‏83 KB

nagaoka 様
平素より弊社製品をご使用いただき誠に有難うございます。
日本ナショナルインスツルメンツ技術部の星と申します。
ご指摘有難うございます。
また、本件に関しましてご迷惑をおかけしたことを深くお詫び申し上げます。
こちらの問題は既に報告されており、2008年6月版のマニュアルでは修正されております。
下記リンクに修正されたマニュアルが添付されておりますのでよろしければご確認ください。
NI USB-622x/625x/628x OEM User Guide
http://digital.ni.com/manuals.nsf/websearch/011F1546F2BA881F8625746C007888E2
宜しくお願いします。
日本ナショナルインスツルメンツ株式会社
星　大輝

Similar Messages

DAQ Signal Accessory ve USB-6255 Bağlantısı

Selamlar,
Elimdeki DAQ Signal Accessory'yi USB-6255 Screw Term Tipi M serisi DAQ cihazına bağlamak istiyorum (sadece analog input kanallarını kullanacağım).
ni.com/manuals'te yer alan 1996 tarihli DAQ Signal Accessory manual'inde "SH68-68 kablonun bir ucunu DAQ Signal Accessory'e diğer ucunu E serisi
DAQ cihazına bağlayın" bilgisinden başka bir bilgi yer almıyor. buradan yola çıkarak DAQ Signal Accessory üzerindeki "68 pin device (Diff mode)"
connectorüne ait pinout bilgisinin 6036E E serisi DAQ kartına ait pinout dağılımı ile aynı olduğunu söyleyebilir miyiz veya bu connector'ün pinout
bilgisine sahip olan birileri var mıdır?
Not: M series manual'inin "M series and E series pinout comparison" bölümünde gördüğüm kadarıyla sadece dijital kanallar arasında farklar bulunduğu
için DAQ Signal Accessory M serisi bir DAQ cihazıyla haberleşebileceğini düşünüyorum...
Teşekkürler

Selamlar,
Sanırsam talebim yanlış anlaşıldı:
DAQ signal accessory'den çıkan SH68-68'in diğer ucuna bir ucu kesik SCSI 68 pin kablo takarak bağlantı yapmak istiyorum.
Ekteki resimde görüldüğü şekilde bazı pin'lerin bağlantılarını yaptım. Ancak DAQ signal accessory'nin tüm pinoutunu bilemediğim için tüm pin'leri bağlayamadım:
E serisi 68 pin'li DAQ kartlarında örneğin 20 no'lu pin 6036'da "NC" iken 604x serisinde aynı pin "AO Ext Ref" sinyali tarafı için kullanılıyor. Yanlış bağlantı yapıpta
cihazlara zarar vermemek için DAQ signal accessory'e uygun pinoutu öğrenebilirsem, 6255 ile pin bazında eşleştirme yapabilirim.
Kolay gelsin...
Attachments:
DAQ.jpg ‏151 KB

IDEA: add a USB Standard-B connector to use any laptop as an external hard disk

Hello Lenovo,
Here is an idea for you:
Add to your laptops a USB Standard-B connector with the following functionality:
When the power of the laptop is OFF,
you can connect the laptop to another laptop using this connector,
and use the internal harddisk of the laptop as an external harddisk for the other laptop.
Regards
Bogdan

From a normal external drive, no, it's not possible. The only device that would approximate this sort of functionality that I've heard of would be the Seagate GoFlex Satellite:
http://www.seagate.com/www/en-us/products/external/external-hard-drive/goflex-sa tellite
Regards.

Acquisition sur USB-6255

Bonjour,
J'utilise un boitier USB 6255 avec deux connecteurs 68 pins et les cables correspondant de chez NI. J'ai besoin de contrôler 24 voies en analogique et une 25e voie (somme des 24 précédentes) qui sert de trigger. Normalement chaque voie déclenche individuellement et la voie somme (la 25e) me permet de déclencher l'acquisition. Après analyse des voies, j'ai des voies en doublon (même signal dupliqué sur 2 voies). J'ai cru lire un truc sur le forum anglais au sujet de voies ghosts. Mais je suis en differentiel non référencé et j'utilise une masse qui fonctionne très bien lorsque j'utilise une carte PCI 6071E. Est-ce que cela pourrait être lié à la qualité de la connectique ? Comment faire pour contourner ce problème ?

Bonjour Greub,
je ne suis pas sûr d'avoir saisi. Avec la 6071E la mesure multivoie se passe -t-elle bien ?
Voici une doc qui t'aidera si tu ne l'as pas déjà consultée:
ghosting
Cordialement,
Romain DUVAL || Application Engineer Specialist ||Certified LabVIEW Architect (CLA) || Certified TestStand Architect (CTA)
National Instruments France

HP Omni 10 5600US - Is there a USB to barrel connector charging cable?

As we all know, the power cable for the Omni10 5600US leaves much to be desired.
Barrel connector. Fine
Cant use the USB port to charge. Fine
BUT...Is there a USB to barrel connector charging cable? Arent USB cables just basically wires arranged in a certain sequence so it should be possible yes? I do not want to carry around the little mini power brick around with my tablet and the option to be able to charge from a portable battery, my laptop, a usb cigarette lighter, or even a buddies phone charger where the USB cord can break away would really make quite a difference.
Even if I did bring my power brick to work , its still isnt long enough to plug into my power strip and up through the desks cable management.

Yes you can. You'll need to purchase a USB OTG (on-the-go) cable. I recommend using a drive that has its own power supply but I've successfully used small USB powered drives also.

Low pass filter of DAQ USB 6255

Hi there
I am using USB 6255 data acquisition board. The cutoff frequency of the internal low pass filter is 1.7 MHz, therefore, the background noise with frequencies below 1.7 MHz cannot be eliminated. The multiple channel signals I am measuring have 10 KHz frequency and the amplitude from 2 mV to 20 mV, but the accurate measurement cannot be achieved even I set the AI measurement range is 100 mV. Could you please guide me to add a extra analogue or digital low pass filter and keep the fast response time if possible? Thank you.
Regards
Jiabin

Hi Jiabin,
Are you using LabVIEW to record your acquisition? If so you can use our 'Filter express vi' to achieve this. The configuration window is shown below:
Let me know if this helps,
John McLaughlin
Insides Sales Engineer Team Leader
National Instruments UK & Ireland

I bought a camera connection kit. First time it worked fine, using the USB connector, but now neither the USB or SD connector works. The iPad shows a connector is attached, but Photos doesn't open. Any ideas? thanks

I bought a camera connection kit. First time it worked fine, using the USB connector, but now neither the USB nor SD connector works. The iPad shows a connector is attached, but Photos doesn't open. Any ideas? thanks

If you have not done so, try exiting the Photo app (and maybe more apps if you have a lot open) from the Open Apps List and see if a discount/reconnect opens the app. If that does not work, try powering down the iPad and test. If it is still not working try a hard reset by pressing both Home and Sleep/Wake buttons at the same time until the Apple graphic appears, ignoring the Slide to Power Off button.

I want to buy a cheap usb/sd card connector

I want to buy a cheap usb/sd card connector for my iPad for the very rare occasions when I may need it so don't want to spend any more than I have to - any recommendations please ? Roger

Hi, this one may be what you need: http://www.pickegg.com/wholesale/5-in-1-sd-tf-ms-m2-mmc-flash-card-reader-usb-ca mera-connector-kit-for-ipad-white.html.
Hope it helps.

USB 3.0 connector

I just purchased a MSI P67A-C43 B3 mainboard and a MSI NightHawk ATX Black Mid Tower Case. Does the usb 3.0
connector on the case also connect the top usb 2.0 ports?

If the USB 3.0 case connector is like the one on my Lian-Li, yes, it has a splitter built into it that connects to the mainboard USB 3.0 header & it enables one USB 3.0 & one USB 2.0 case port.

Error Code 88709 Reading NI USB-6225 OEM

We have an issue that exists on one of two nearly identical systems that use NI USB-6225 OEM cards. We are reading 75 channels at 1 kHz once per second. On one of two systems the Error Code -88079 occurs intermittantly and when this happens the DAQ measurements stop though the code does not freeze. We do not write to the 6225 card, the only thing we are doing is reading the AI channels.
Our LabVIEW version is 2013 SP1 f2 and NI-DAQmx is version 14.1. NI MAX is v14.0.0f0.
The first system runs on a Windows 7 desktop workstation and has serial mass flow controller software with timers to change flow and concentrations based on a control file as well as a MODBUS TCP NDIR interface. This system is complex but works perfectly.
The second system runs on a Windows 8 laptop. The mass flow software, timers, and NDIR interface were removed from the code of the first system to simplify the software for the second system.
It is only the second system that produces the Error Code -88079. This can happen once a month or several times a day.
I've removed all the 'bloatware' from the Windows 8 laptop and ensured that nothing is set to hybernate or sleep and also turned off the Windows and other automatic updates because these systems must run 24/7 for a year.
So, what is the best resolution for the Error Code -88079 problem with the second system?
The DAQ card was calibrated and tested ISO-17025 through NI by an independant agency so it is not likely to be faulty but we could replace it with another (not ISO-17025) card we have on hand for diagnosis
The USB cable is a possibility. We could obtain a high quality USB cable and make sure the ends fit tightly. Disconnecting the USB cable when the code is running produces Error Code -88079...
Any other suggestions?
Warm Regards,
Lloyd

Hi Saturn233207,
Could you give more detail about the error that you are getting? What are the steps to reproduce the error? Is there any descriptive text at all in the error dialog box - maybe post a screenshot of the error?
Also, as you mentioned I believe it would be a good idea to ensure that you are using a quality USB cable.

USB-6251 OEM Device ID

USB-6251 OEM版　NI-DAQmx8.5を使用して　Visual C++.NETでプログラムを作成しています。
DAQmxGetDevProductNumで得られたDevice IDは"0x729e"でした。
NI-DAQmxヘルプの"Supported Device ID Numbers"のリストには載っていませんでしたが、
この数値は正しいのでしょうか。
解決済！
解決策の投稿を見る。

いつもお世話になっております。
日本ナショナルインスツルメンツ技術部のサハと申します。
デバイスのIDは問題なく得られたということはデバイスが正式に認識されて
正常に動作しているということになります。得られたIDはリストにはないことに
関してですが、おそらくこのリストは通常のデバイス用のリストでありまして、
OEMデバイスはこのリストには入ってないと思われます。この番号を使って
プログラムを作成し、何か問題がありましたら、ご連絡ください。
以上の内容で何かご不明な点がありましたら、ご連絡願います。
サハ｜技術部｜日本ナショナルインスツルメンツ

Usb 2.0 connectors - jusb1

hey just wondering my msi P67a GD55 B3 only comes with 1 on board usb 2.0 connector (internal I/O connector) but i have 4 usb hubs on my front panel and only 1 slot for the two cables needed.
not sure if that makes sense but just in case;
4 front usb connectors each 2 usb has 1 jusb1 cable, so in total 2 cables
the mobo has one usb 2.0 and one usb 3.0 (internal I/O connectors)
is it possible to get around this? like a 2-1 adapter or a usb 3.0 to usb 2.0 internal I/O connector?
thanks!

Quote
is it possible to get around this? like a 2-1 adapter or a usb 3.0 to usb 2.0 internal I/O connector?
I believe there are gender changers available that will do that.

Lenovo J Desktop - K8m800-M3 motherboard front USB connectors pinout

HI!
I've got a Lenovo Desktop with K8m800-M3 Motherboard. I need the pinout of the two front USB connectors: they are 13 pins disposed in 3 lines ad below:
|-||| |-|||
||||| |||||
||||- ||||-
USB1 USB2
USB3 USB4
I can't find out the user manual, then I don't know how to connect front USB ports...can you please help me?
Thanks in advance.

hi robyone69,
Welcome to the Lenovo Community.
If you have the Lenovo J105 (types 8458, 8459, and 8460), you can find the connector layout under page 118 on the Hardware Maintenance Manual.
Spoiler (Highlight to read)
If the layout is different, you can find the user guide / maintenance manual on the lenovo suport.site (http://support.lenovo.com). Sample search:
Spoiler (Highlight to read)
Hope this helps.
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Need DV6000 USB Power board cable pinout for mainboard connector

I have a DV6000 and the connector in the mainboard broke. what is the pinout of the connector, I can put the connector on 2 ways, 180 degrees around.

Wb8wbn.
I would check to see if this is what you want.
The DC jack is mounted on a small board not the mother board???
http://www.ebay.com/itm/HP-Pavilion-DV6000-DC-Power-Jack-USB-DDAT8APB2000708-/261165970123?pt=LH_Def...
Just replacing the board would be much easier.
That is not to say that another DV6000 has the DC jack on the motherboard.
Not 100% sure.
REO
HP Expert Tester "Now testing HP Pavilion 15t i3-4030U Win8.1, 6GB RAM and 750GB HDD"
Loaner Program”HP Split 13 x2 13r010dx i3-4012Y Win8.1, 4GB RAM and 500GB Hybrid HDD”
Microsoft Registered Refurbisher
Registered Microsoft Partner
Apple Certified Macintosh Technician Certification in progress.

Freezing MBP when inserting USB or Thunderbolt connector

I have quite new MBP Retina, it was working very well in the beginning but now, without any reason, it is not working that well. When I connect any USB connector (printer or external HDD), thunderbolt with ethernet adapter etc. - the cursor freezes for 5-10 sec (just now when connecting the ethernet adapter, the computer has frozen completely and I had to do a force restart). The same when opening the lid - it often takes quite long time before the laptop awakes (there is a grey and then light blue screen) and often the cursor freezes too for some time.
This is very strange and unwelcome and certainly not as I would expect "the best Mac ever" to behave - for such a price. As I said - it was not doing like that from the beginning, but was spoilt like this some time ago. What can be the reason and how to bring it back to normal functioning ?

It's new and it seems as if you are having hardware problems - take your machine to your local Apple Store or an AASP and have them diagnose and fix the problems. Could be logic board related since it's happening with both ports.
Good luck,
Clinton

USB-6255 OEM Connector Pinout

Similar Messages

Maybe you are looking for