Usb 6341 counter number of buffer

Hi
I will use usb 6341 to measure digital pulse.
What is maximum buffer when i use 25Mhz sample clock with buffered mode?
(It shown error when i set 25Mhz clock, N sample mode, 1M sample)
Is there any fast edge measerement with usb 6341?
(I want ns time scale with long time)
Thx

25 MHz is a very large sample rate for a counter... can you elaborate on your application? There really shouldn't be any reason to sample the counter this quickly. If you're trying to timestamp your external pulses with the highest possible precision, I would instead use the external pulse as a sample clock and count the internal timebase (assuming the external pulse isn't also 25 MHz...). Doing this would actually get you 10 ns resolution (instead of 40 ns that you are hoping for with a 25 MHz sample clock) and the required throughput would be based on the rate of your external signal (which is presumably less than 25 MHz, which is the highest frequency that you can connect through the PFI lines anyway...)
To answer your question though...
The on-board FIFO is 127 samples per counter. If your task is measuring more samples than this, you would need to be able to read data off of the device at least as fast as it is coming in. On USB that is going to be highly system dependant (one benchmark here reported 8 MHz). If you really need the higher throughput you are asking for you will probably want to switch to the PCIe version of the 6341 (20 MHz on a single channel mentioned here, I'm not sure if higher rates were tested but I wouldn't be surprised if 25 MHz is sustainable as well).
Best Regards,
John Passiak

Similar Messages

Is it possible to maintain the last AO value after the DAQmx task is done on device DAQ USB-6341 ?

Hi all,
I use the device DAQ USB-6341 to generate the desired voltage waveform by the "finite samples" sample mode.
I notice that the channel resets to zero volts after the DAQmx task is done and the DAQ USB-6341 does not have
the property AO.idleOutputBehavior to select "Maintain Existing Value".
How can I maintain the last AO value after the DAQmx task is done on device DAQ USB-6341 ?
Thanks.
Godel

How many computers do you have in the network?
What is the IP address and default gateway number on your computer?
In order to connect to the wireless network, WVC80N should get valid IP address from the access point.
If the access point has capacity to assign a private IP address to the computers and devices then I think you can use WVC80N.

SCXI with USB-6341

From a hardware standpoint, can a USB-6341 be used to capture data from an SCXI chassis (ignoring the connector/wiring situation)? I would like to use this scenario and program in C++ but the device access is controlled through MAX and MAX doesn't allow the USB device to be selected as a chassis communicator. It is my understanding that M-series USB mass terminated devices could be connected to SCXI so I'm wondering if it is just a list of compatible devices MAX uses and the USB version of the 6341 isn't on the list for whatever reason (which I would be curious to know).
In this note mass termination is called out specifically (for the M-series USB). What is the difference between mass termination and the wiring pin to pin?
I realize I can communicate with the SCXI in other ways but going through MAX would be much simpler for me (especially for calibration/troubleshooting) and I could use the NI provided DAQmx C examples.
Thank you

Unfortunately this is for work I do at home so I'm in the usual predicament of having to spend more time doing things myself where I can't afford to do it otherwise. I thought the device did have the APFI capability when I purchased it. Accuracy isn't a concern for me because I just need to see the signals (for example: high channel count temperatures where most devices are +/- 1°C on the spec sheets and I just need to know if heat transfer is working properly). I am trying to move away from a DAQcard that I was using for the SCXI to something USB that I can use with any computer in the future.
By the way, I'm only using bare wires inside the X-series enclosure. The cable is an EPM cable and I wired everything per the pinout diagram provided by NI for that cable. The BNC breakout I have wired to the SCXI chassis was working properly so I assumed it was good to go but couldn't get the device to show in MAX. Now I realize it is just the feedthrough on the 1349 that is working and communcation with the chassis won't work.
Thank you

USB 6341 versus 6215

I was using a USB 6215 OK. It worked great. However I needed to controll my valves by hardware I/O. I just installed the new USB 6341. I am trying to control 1 line at a time. I am currently sending a binary or hex value to control the valve. It does not act the same way as the USB 6215 DAQ. Does anyone have a simple approch to control one bit at a time. I am not familur as yet with the DAQ USB 6341.
Philip
Solved!
Go to Solution.
Attachments:
6341.JPG ‏42 KB

Dennis Knutson wrote:
tbob wrote:
Put the write function before the start function. The write function simply writes data to the DAQ card buffers. The data does not get generated until the start function is called. So in your code, you were telling the DAQ to write an empty buffer before you filled it with data. Try reversing the order and see if it works.
Sorry, putting the Start Task first is normal. Just look at one of the simple examples such as Write Dig Chan.
Normal, maybe, but not always so. Look at the example called Write Dig Chan-Ext Clk. It has the write before the start. I guess it works both ways. I have always put the write before the start because I have sometimes used external triggers. That lead me to believe that you have to write to the buffer before you start the task. I do the same with Analog Outputs also.
- tbob
Inventor of the WORM Global

How to count number of sales orders generated in a month in SAP SD

Hi SD Gurus,
I have a very strange query from client. I have to count the number of sales order created in a month for a z report. For example 30 in Jan, 25 in Feb etc. Could anyone suggest me How to count number of sales orders generated in a month in SAP SD.
Regards
Vinod Kumar

Hi,
Goto the T.Code "SE16" or "SE16n" or "SE11".
Enter the table name as VBAK
Enter the created on date as the starting date of the period and to date as the end date.
Enter.
Click on "Number of Entries".It will tell you the number of entries created in a particular period.
If you want a report,goto the T.Code "VA05n".
Regards,
Krishna.

How to Count Number of completed line items in past 6 months / 12 months ?

How to Count Number of completed line items in past 6 months / 12 months ?
Hi,
I am trying to count "Number of Completed Line Items in Purchase Order Document" for my Key Figure ZPO_CNT.
Purchase Order document = ZEBELN
Line Item = ZEBELP.
I need to find and count if the Line Item has been received in the past 6 months from today and similarly in the past 12 months.
I have "Delivery Completed" field, ELIKZ.
So, based on this would I be able to calculate it in Query Designer?
If so, Please let me know how

Hello Deva
If youe want to calculate the completed line item for last 6 or 12 month then i think u will be displaying the query data for these montrhs...create a customer exit to give you date range and restric it in filter area....
Now Choose any of the below option
1. I would suggest to implement an additional key figure "counter" in cube and fill values with one for which delivery is completed.
Now use calculated key figure in Query Designer based on logic
IF counter = 1 THEN counter ELSE 0
OR
2. create a formula variable based on ELIKZ and use replacement path variable, it will display you no. of docs for which delivery is completed....
Award points if it solves your problem
Revert back in case of further assistance...
Thanks
Tripple k

How to Count number of words in a file....

Hi Experts,
I have uploaded the text file, from the application server, like this:
call function 'GUI_UPLOAD'
exporting
    filename = LV_ip_FILENAME
tables
    data_tab = LT_FILETABLE.
The text file contains some number character words.... like "sap labs india..... "
Now, I wanted to count number of words in an internal table LT_FILETABLE.... can anybody help me?

Hi,
Special Characters in Regular Expressions
The following tables summarize the special characters in regular expressions:
Escape character
Special character Meaning
Escape character for special characters
Special character for single character strings
Special character Meaning
. Placeholder for any single character
C Placeholder for any single character
d Placeholder for any single digit
D Placeholder for any character other than a digit
l Placeholder for any lower-case letter
L Placeholder for any character other than a lower-case letter
s Placeholder for a blank character
S Placeholder for any character other than a blank character
u Placeholder for any upper-case letter
U Placeholder for any character other than an upper-case letter
w Placeholder for any alphanumeric character including _
W Placeholder for any non-alphanumeric character except for _
[ ] Definition of a value set for single characters
[^ ] Negation of a value set for single characters
[ - ] Definition of a range in a value set for single characters
[ [:alnum:] ] Description of all alphanumeric characters in a value set
[ [:alpha:] ] Description of all letters in a value set
[ [:blank:] ] Description for blank characters and horizontal tabulators in a value set
[ [:cntrl:] ] Description of all control characters in a value set
[ [:digit:] ] Description of all digits in a value set
[ [:graph:] ] Description of all graphic special characters in a value set
[ [:lower:] ] Description of all lower-case letters in a value set
[ [:print:] ] Description of all displayable characters in a value set
[ [:punct:] ] Description of all punctuation characters in a value set
[ [:space:] ] Description of all blank characters, tabulators, and carriage feeds in a value set
[ [:unicode:] ] Description of all Unicode characters in a value set with a code larger than 255
[ [:upper:] ] Description of all upper-case letters in a value set
[ [:word:] ] Description of all alphanumeric characters in a value set, including _
[ [:xdigit:] ] Description of all hexadecimal digits in a value set
a f
      v Diverse platform-specific control characters
[..] Reserved for later enhancements
[==] Reserved for later enhancements
u2192 More
Special characters for character string patterns
Special character Meaning
Concatenation of n single characters
{n,m} Concatenation of at least n and a maximum of m single characters
{n,m}? Reserved for later enhancements
? One or no single characters
Concatenation of any number of single characters including 'no characters'
*? Reserved for later enhancements
+ Concatenation of any number of single characters excluding 'no characters'
+? Reserved for later enhancements
| Linking of two alternative expressions
( ) Definition of subgroups with registration
(?: ) Definition of subgroups without registration
1, 2, 3 ... Placeholder for the register of subgroups
Q ... E Definition of a string of literal characters
(? ... ) Reserved for later enhancements
for more details please refer the following,
[http://help.sap.com/abapdocu_70/en/ABENREGEX_SYNTAX_SIGNS.htm]
[http://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/902ce392-dfce-2d10-4ba9-b4f777843182?QuickLink=index&overridelayout=true]
Thanks,
Renuka S.

How to count number of edges using PXIe-6363 Counters

Hello,
I am trying to count number of edges in a test signal in a 50 ms duration. I am using PXIe-6363 card and connecting the test signal to CTR 0 SRC (PFI 8). Is it a correct connection? What else do I need hardware-wise to make a correct set up for this application?
Thanks
Jeet
Solved!
Go to Solution.

Hi Jeet,
When you say interrupt signal, do you mean a pulse that will pause your counter task? If that is the case, and you want to pause your task with a digital pulse, you need to use the DAQmx Trigger Property Node and set that to Pause, Trigger Type. As you said, you can connect that signal coming from the chip to any PFI line and then set that line as the source of the property node.
There is an example that you can use that does exactly what I just described. This example is called Count Digital Events-Pause Trig.vi, and you can find it by going to Help>Find Examples..., then on the NI Example Finder window go to the Browse tab and navigate in the folders to Hardware Input and Outpout\DAQmx\Counter Measurements\Count Digital Events.
Regards.
Jorge
Applications Engineer
National Instruments
Certified LabVIEW Associate Developer (CLAD)

How to count number of raw & put result top of page?

I try to count number of table raw it work fine but when I wont to put result top of page it dose not work
only count one table raw
REPORT ZTEST.
DATA: it_sflight TYPE TABLE OF Sflight WITH HEADER LINE .
DATA counter TYPE i VALUE 0.
start-of-SELECTION.
SELECT-OPTIONS: carID for it_sflight-carrid.
SELECT-OPTIONS: connID for it_sflight-connid.
SELECT * FROM Sflight INTO CORRESPONDING FIELDS OF TABLE it_sflight
WHERE carrid IN carID and connID IN connid.
loop at it_sflight .
counter = counter + 1 .
write: /5 it_sflight-carrid,sy-vline,
           30 it_sflight-connid,sy-vline,
              45 it_sflight-fldate,sy-vline,
                60 it_sflight-currency,sy-vline.
ULINE.
endloop.
end-of-SELECTION.
TOP-OF-PAGE .
*START-OF-SELECTION.
WRITE: 'Total Rows : ', counter.
ULINE.
WRITE: /5 'Carrid',sy-vline,
        30 'Connid',sy-vline,
        45 'Fldate',sy-vline,
          60 'Currency',sy-vline.
ULINE.
how can I solve this problem ?

Hi
Instead of using counter in a loop use describe statement.
Describe it_sflight.
the no of rows will get populated in the system variable sy-tfill.
DATA: it_sflight TYPE TABLE OF Sflight WITH HEADER LINE .
DATA counter TYPE i VALUE 0.
start-of-SELECTION.
SELECT-OPTIONS: carID for it_sflight-carrid.
SELECT-OPTIONS: connID for it_sflight-connid.
SELECT * FROM Sflight INTO CORRESPONDING FIELDS OF TABLE it_sflight
WHERE carrid IN carID and connID IN connid.
DESCRIBE TABLE it_sflight.
loop at it_sflight .
counter = counter + 1 .
write: /5 it_sflight-carrid,sy-vline,
           30 it_sflight-connid,sy-vline,
              45 it_sflight-fldate,sy-vline,
                60 it_sflight-currency,sy-vline.
ULINE.
endloop.
end-of-SELECTION.
TOP-OF-PAGE .
*START-OF-SELECTION.
WRITE: 'Total Rows : ', sy-tfill.
ULINE.
WRITE: /5 'Carrid',sy-vline,
        30 'Connid',sy-vline,
        45 'Fldate',sy-vline,
          60 'Currency',sy-vline.
ULINE.
Thanks
Rahul jain
Edited by: Rahuljn on Feb 2, 2011 10:58 AM

Using USB 6341 device for frequency generation but level is droped when conect

i am using USB-6341 Daq Device for frequency generation. The desired frequency is generated correctly but when i connect to other device the voltage level i means the Peak to Peak voltage of the frequency dropped to 0.6, 1 Volt and also the frequency fluctuated. As I disconnect it from the load or the device the frequency becomes constant and peak to peak voltage becomes 5.
Please some help me to resolve my problem.
Thanks
Best Regards
Naseeb
Solved!
Go to Solution.

Hi Nasib,
I just wanted to clarify a few more things. Can you answer the following questions?
What frequency are you trying to generate?
When there is no load connected do you see the desired frequency?
When the load is connected, does the frequency always change to the same value or does it fluctuate within a certain range? If it fluctuates, what is the range?
Also, what microcontroller are you using?
Can you provide any images?
Regards,
Travis Ann
Applications Engineer
National Instruments
Applications Engineer
National Instruments

How to count number of ones in table

Hello,
i created one table 16x32 each cell is updating 1 byte of data,how to count number of one in all cell,and is it right way to calculate check sum??
thank you

The simplest way is to call GetTableCellRangeValues with VAL_ENTIRE_TABLE as the range, next summing array elements.
But I don't understand your comment on checksum, so this may not be the more correct method for your actual needs: can you explain what do you mean?
Proud to use LW/CVI from 3.1 on.
My contributions to the Developer Zone Community
If I have helped you, why not giving me a kudos?

Number range buffer is full

Hi,
During the creation of customer in customer master data, we encountered an error that says Number range buffer is full. Now, we cannot proceed with the saving. How can we correct this.
Thank so much.
Rachelle

Have you checked OSS? There are a number of notes regarding number range buffers (not necessarily BCS related). For example, 964929 and 633980.
If you know the offending number range, you can change the buffer settings through t-code SNUM....just make sure you know what you are doing relative to your instance name, number of application servers, requirements for continious numbering, etc.
- Chris

URGENT HELP NEEDED: counting number of particles from image

this image on the left is showing particles
hello i want to create a small VI that can count number of particles from a image that i load up. please see the attached image of particles and the VI printshot.
I have used the tutorial "counting number of particles" but still the above VI does not work. it shows the number of particles = 1.. I do not know why it is doing so??
I am not an expert in Labview so please can someone tell me where the problem is. sorry i could not attach the VI file itself but i have given an image of it..
after anyone has solved this problem, i have to create a live system that will get live images from the camera - four frames every sec and the above VI has to count the
number of particles for each frame and output to the user?? is this possible can anyone do it for me???
p.s. in the above VI i read the image from file and count the number of particles. i do not do it to the binary image becuase the binary image is only a black screen
when i run it
thankyou

Hi Farhan,
Vision Assistant would be the best option to create some steps which you can then export to LabVIEW. You should try using the IMAQ Find Circles.vi. The attached image helps you find the number of circles of an image acquired from a camera. I have used the IMAQdx VIs in this example.
Adnan Zafar
Certified LabVIEW Architect
Coleman Technologies
Attachments:
vision.vi ‏59 KB

What is a best practice for counting number of payments in Payroll Run?

I'm trying to get a feel for what people are using as a means for counting number of payments being created during a payroll run. I would like to get a total number of checks, direct deposits, wires and zero net checks. My initial thought is to use the Pre-DME number "Selected and Evaluated Persons". This number seems to always match the number of persons "Selected" and "Evaluated" in posting to FI/CO.
Since many companies are restricting use of SE16 and access to many of the BT tables is locked down, I would like to use something that the end user has access to and can easily use. I don't believe the spools from RFFOUS_C and T are appropriate since it would have overflow pages (2 page REM Statements) in that number and thus would not be an accurate reflection of total number of payments.
I would appreciate your insight and thoughts on this topic.
Thanks!

Hello Jennie,
This is what we do every payroll:
1. After running live payroll and before exiting our users run wage type reporter /559 to get the payroll net pay. They also run Postings to FICO simulation run to check payroll net pay GL account. This match all the time. So this is the first pass.
2. They finish all subsequent activities in PRD run upto RFFOUS_T.
3. We have developed a custom report which almost looks like REGUH which gives the net pay details by every payment method and amount to be deposited or paid. We match this report from the output we received from step 1.
4. Run postings to FICO live and check the payroll net pay GL account for final validation.
The steps might sound tedious but of a great use.
Arti

Count number of records in a internal table

hi
i want to count number of records in internal table
pls let me know how to count the number of records in a internal table.
regards
Arora

hi
one way is
data field type i.
Decribe table itab lines field.
write: / field.
displays the no of records in tha internal table
or if u want to write logic.
data:
w_count type i.
loop at itab.
w_count = w_count + 1.
endloop.
write: / w_count.
displays the no of records.
reward points if useful.

Usb 6341 counter number of buffer

Similar Messages

Maybe you are looking for