USB and sound problems on a P10-221

Hi! I'm portuguese and I don't write to good.
I have a problem with my bluetooth, after installing Windows Service Pack 2 and a Bios update.
I have installed the Version 1.90 , after activating my bluetooth, the Notebook shut's down.
After rebooting of the laptop, the sound and usb connections were gone to, what can I do ?
The Notebook is a Satellite P10-221
[Edited by: Forum Moderation]

Hi,
At first I would re-install the chipset drivers for your Notebook.
After that Uninstall the Bluetooth Stack and re-install it also.
There is also a Information Sheet for download available to get information about new drivers for Service Pack 2. Look at http://eu.computers.toshiba-europe.com
Config free (4.90.57) and PC Diagnostic Tool (3.0.6) are available for Windows XP Service 2 Users.
Have a look at http://eu.computers.toshiba-europe.com to get the updates for download.
Keep me posted about your results
Bye

Similar Messages

Neo platinum case issues? usb and sound

Hi first time on the board..
now I just built my first comp and it boots up without a hitch everything fine i think then low and behold I have no sound or front usb support so i search thru the forum and find the article on the usb problems and I think what if thats my problem so i un plug the front usb and sound connect and my rear sound starts working but now i have rear sound and usb but no front also my hdd led and my power led will not work. I want to keep my case but i need my hdd led and my power led to work or the case is worthless i have a cool master cavaliver case. PLEASE help a n00b get this working thanks

Quote
my hdd led and my power led will not work
Means you dont have then on the right way round.
The switch / reset can go on any way, but leds have to be correct.

Satellite L750D - BIOS update 2.1 and sound problem

Hello
I have little problem. I have been downloaded from your website BIOS 2.1 for Toshiba Satellite L750D (PSK32E).
I have been updated BIOS to 2.1 and start problem with sound. When I start game, music or something other only 2 first minutes sound plays properly but then it stops for no reason. No sound at all. I have been reinstalled op system but the problem is still there.
Sound works for 2 minutes only then is completely off. Every start application with sound plays 2 minutes and stop all quiet is. I have made a probe on my mother laptop its a twin laptop. I have been updated bios same problem 2 minutes and then no sound. My operating system is win 8 pro 64 my mother laptop is with win 7 x64 premium.
Two BIOS updated 2.1 ver on L750D and the problem is same. Please fix BIOS.

The BIOS seems to be very old. I was released nearly 1.5 years ago so to be honest I doubt its and BIOS issue.
I had the similar issue with my other notebook equipped with an Realtek sound card.
The sound appeared again after plugging and removing the headphone jack
But i could solve this installing the newest sound driver update from Realtek driver page.
But it seems that your Satellite does not support Realtek sound chip but Conexant sound chip.
Therefore the solution might not be useful for you.
However, I think you need to update the sound driver.I recommend you to google for Conexant SmartAudio HD driver and to test the newest available driver version.
In internet I could found the Conexant SmartAudio HD Driver version 8.65.9.51 for Win 7/ Win 8 / Win 8.1
Not quite sure if this is the newest version but you can test it.
In order to manually update your driver:
1. Go to Device Manager (right click on My Computer, choose Manage and then find Device Manager in the left panel)
2. Right click on the hardware device you wish to update and choose Update Driver Software
3. Choose to select the location of the new driver manually and browse to the folder where you downloaded the driver

Blue Screen and Sound Problems, In Desperate Need of Assistance

About a week and a half ago, my computer officially stopped showing anything on the display when I tried to start it up. It had been doing it on and off for a long time, but I would eventually get it to display. Not this time...
My husband and I took our 30" Cinema Display and G5 tower to the iStore. The display was tested, and it worked fine. The associate said the problem was the video card.
After doing much research, I decided upon the flashed GeForce 7800 GS, per the suggestions of japamac on this forum. After I received and installed it, the display worked again and everything seemed great! It came with a CD with a patch on it, saying it was for *10.4.9 or later*, so I installed the patch and ran the permissions command. I had to go on a business trip immediately as the permissions command was running, so I left the computer to do it's thing, knowing it would sleep after a while.
When I got back home from my trip, I eagerly hopped on my computer. I attempted to awake it from sleep, however it froze. I was not able to tell if the permissions command ever finished completely.
I restarted the computer and everything seemed fine. A few hours later, my husband hopped on the computer about to test the new card on a game, but it froze before he could do anything. We restarted the computer, and that's when the blue screen issue started.
I tried resetting the PRAM, starting it up on the install disc (which didn't work), I tried holding down the S key (which also didn't work), and I tried holding down shift for Safe Boot.
The Safe Boot works, in fact I'm on my G5 right now. I did the permissions command again, thinking that it must've not ran all of the way and the permissions were broken. When it finished it gave me a massive list of "permissions differ"s with 10 "Warning: SUID file "____" has been modified and will not be repaired" messages at the end.
I contacted the seller on ebay, who ended up telling me the patch was only for Tiger, despite the file saying "or later". I really thought I messed up the permissions badly from that and tried running the permissions repair, but that did not help.
Thinking I had no other choice, I backed everything up and I reinstalled Leopard (choosing to Archive). After it finished reinstalling, the computer restarted and it booted up normally. I thought my problem was solved! However, once I let it sleep and came back later, it was frozen. I restarted and had the blue screen problem all over again, to my disappointment.
I tried restarting, the PRAM, the permissions (which did not list those SUID warnings anymore)... There was once that I restarted and it gave me the blue screen, I tabbed twice, hit enter, and entered my password though I couldn't see anything. I heard the computer moving like it was logging in. I pushed the power button on my display, and magically the screen displayed my desktop with the "Are you sure you want to put your computer to sleep?" window.
However, this only happened once, and afterward I noticed an issue when I tried to wake the computer from sleep. It would try to wake up, then go back to sleep, try to wake up, go back to sleep... So I contacted the ebay seller again, explaining what had happened and that it made me think it is an issue with the card itself, not permissions. (Fearing that if it is permissions, I would have to reinstall the OS again, but choose to erase the disk this time.) I asked if the seller knew anything about this.
The seller contacted me back saying, "Hello again, yes, wake from sleep is a common issue of many modified cards for Mac , so you better turn it off if you are not use it, its better for both the video card and power supply of your G5,
hope you understand about it , thanks". Well, that really would have been nice to know in advance... but regardless, the more important issue is the blue screen on startup.
On top of all of this, when I tried to watch a video tonight I noticed the sound was not working. I made sure it wasn't muted, I made sure the optical cable was connected, nothing. I restarted, nothing. I did not have any problems whatsoever with the sound before this, and I'm not sure if it has anything to do with the card (I wouldn't think so), or that something needs to be reinstalled since I reinstalled the OS. The System Prefs > Sound, Is not finding any devices.
I've restarted the computer so many times since the initial failing of the video card, I really hope all of the restarting hasn't damaged anything. As old as my Mac is, it's been working perfectly normally until the graphics card went out. After that, it's seemed like everything is falling apart. Thank you for reading my long history of difficulties, and I hope someone (maybe japamac?) can help me!

Hi-
I understand why you would suspect the latest hardware addition, and the conflicting/misunderstood advice given by the seller isn't helping.
I don't know of any cards that have "known" issues with sleep from the flashed realm.
Of the 10 different makes and models that I use or have used, flashed by myself or others, I have never seen an issue with sleep.
This includes 2 different Geforce 7800 GS cards.
The most common reason for a blue screen at boot is an incompatible Login or Startup item.
These are disabled during a Safe Mode boot.
http://www.thexlab.com/faqs/startupitems.html
As for the Geforce 7800 GS, there was a patch for OS 10.4.9 only. This was to allow for the proper reporting and use of the appropriate OpenGL engine.
After 10.4.11, and in Leopard, the OpenGL engine is properly selected for the card.
Since this is simply a reporting issue, and not a performance issue, the patch is not a mandatory thing.
There is an issue with the ROMs used in some Geforce cards that causes a boot delay (a blue screen) for up to 6 minutes.
Most guys don't use those ROMs anymore, but I guess that someone may not have bothered to get the new ROM.
Removing the AppleHWSensor.kext from /System/Library/Extensions will correct this issue.
This, however, is historically a G4 issue only.
There are a couple possible scenarios that I think may apply to you:
1- The card is overheating, thus the occasional success or Safe mode only boots.
Check that the fan is spinning.
2- The auxiliary power is not connected, or has a poor connection.
Sometimes the pins on a Molex adapter (the female side) are so tight that they push out, rather than allowing the male pin in.
Conversely, a stretched out female pin would not properly contact the male pins of the graphics card.
Double check connections at the optical drive and at the graphics card.
While inside, reseat the graphics card.
3- If the card was prepared for use in a G4 by cutting the traces of pins #3 and #11, this can cause problems in the G5.
Most cards work fine, but some Geforce cards complain.
As well, if the pins were taped, the tape should be removed for use in a G5.
http://themacelite.wikidot.com/pins-3-and-11
If the traces are cut, return the card.
If the pins are taped, remove the tape.

SOLUTION to video and sound problems

I know this seems like a very long process, but it actually doesn't take too long (at least with music videos), and it's well worth having the audio and video ligned up properly. So hope it works for you all, let me know how it goes :)
i know a lot of people around are having problems with the video and audio not being together when using converters with mpg files. i've been trying different settings all day and i've come up with the conclusion that muxed mpg files WILL NOT have the audio in sync no matter what settings you use.
HOWEVER, you can download a small, FREE program VirtualDub (which can be downloaded at http://virtualdub.sourceforge.net/). (it requires NO INSTALLATION, which is brilliant)
so, once you've got this program opened:
1. first put your muxed video into there (drag it or "file>open file")
2. then go to "video>compression" and select "microsoft MPEG-4 Video Codec V2" and then press "OK".
3. after that, go to "file>save as AVI", select where you want to save it and then press OK.
NOW you have a non-muxed video file, that you can convert using any of the regular converters (Xillisoft, Videora.. etc.) Personally i use Xillisoft's IPod Video Converter, and ta da, you know have a correctly sync'ed audio and video file compatible with the ipod.
hope it helps everyone else
P4 Windows XP Pro
EDIT: oh yeah, and after you have your converted file using Xillisoft or Videora, you can delete the AVI file and keep the original if you want.

hmm.. ok.. well perhaps you might need the codec installed on your computer.. this is strange i thought it was default..
can you try telling me what options you do get in there? and i'll search to see if you can download it.. OR you can try just selecting another one, i think at this point it doesn't really matter which one, as long as you use one, because an uncompressed AVI is absolutly HUGE. so try another one from the list (preferabley one that says 'no known restrictions' i think) and let me know if the sound is still good after youthen convert again using videora or xillisoft

USB and audio problem on a 975x P PU editon

Hello all,
I would like to say first off that this is my first build so please go a little easy on me. I am computer literate and i ave searched around trying to find the answers but for some reason they elude me. I am a Apple person at heart but when it comes right done to it windows is better for the HTPC side of things (not to mention the room mate agreed to pay for most of the computer). The specs are in the sig but if anything else is needed let me know.
I am having problems with the USB ports on the motherboard and the front of the case. I have the Antec P150 which has a connector for the front 2 USB prots. They are pinned out as follows:
pin 1: USB Power 1
pin 2: USB Power 2
pin 3: Negative Signal 1
pin 4: Negative Signal 2
pin 5: Positive Signal 1
pin 6: Positive Signal 2
pin 7: Ground 1
pin 8: Ground 2
pin 9: Key (no pin)
pin 10: Empty Pin
The motherboard is:
pin 1: VCC
pin 2: VCC
pin 3: USB0-
pin 4: USB1-
pin 5: USB0+
pin 6: USB1+
pin 7: Ground
pin 8: Ground
pin 9: Key (no pin)
pin 10: USBOC
Now the problem is kinda weird as the ports seems to work just fine if the USB thumb drive is plugged in, then i restart the computer. But if i start the computer up and then plug in the thumb drive i don't get any popup. In hardware manager it sees the thumb drive but it has a yellow "!".
The front Audio is somewhat the same way. I know the connection for the audio on the motherboard is HD and my front port are not. The pin setup for the case is:
pin 1: Mic
pin 2: Mic power
pin 3: Ground
pin 4: Front right
pin 5: Front left
pin 6: Rear right
pin 7: Rear left
On the motherboard it is:
pin 1: Analog port 1 - left channel
pin 2: Ground
pin 3: Analog port 1 - right channel
pin 4: Active low signal (unused for me i believe)
pin 5: Analog port 2 - right channel
pin 6: Jack detection return from front panel (jack 1)
pin 7: Jack detection senseline
pin 8: Connector Key
pin 9: Analong port 2 - left channel
pin 10: Jack detection return from front panel (jack 2)
They are connected like the ones here https://forum-en.msi.com/index.php?topic=103220.0.
Right now i have it connected and i can get audio from headphones plugged in but only from the left ear.
I believe I have the correct driver and stuff installed but if anyone has some suggestions please try to post instructions/links to instructions/or links to drivers you think i might need.
Thanks

Quote from: Maesus on 04-February-07, 02:41:18
For USB, do not connect the pin-10.
The audio is a tough one. The 10 pins on the motherboard actually only gives 2 ports. But your chassis has 3 ports. So no matter how you connect them, you only have 2 ports functional. Use the Realtek HD Audio Manager, sort of like the audio control panel. Enable the front ports, and start testing your speakers/mic and see if they work fine. I expect you to come back and tell us how to configure the pins later.
Thats the thing about the USB. I don't have a wire or anything going to the 10 pin. It seems like it should just be a matter of connecting the block and being done with it. I don't get why it is not working.
As for the audio. I will messa with it a little more but i don't really much care it is works or not. While it would be nice I don't really plan on using it.
Thanks
SOME EXTRA INFO: I have been messing around with this and it seems like my USB ports are not working at all. after booting up. As long as i have the USB thumb drive plugged in when i boot the computer i can see it (in the front or back panel) but as soon as i pull it out and try ot put it back in then that is when nothing happens.
So i guess it is not really a connection problem as the front USB do work but only when the thumb drive is plugged in when the computer is booted.
Any help is greatly appreciated!!!

Windows 7 and Wireless Mighty Mouse, Wireless Keyboard and sound problem

Hi,
I just installed Windows 7 x64 Ultimate on my iMac 24" white ( OS X Leopard 10.5 ). Surprisingly, it installed without any problems. The only problems I have now are the Wireless Mighty Mouse and the Wireless Keyboard ( alu ).
After I installed Windows I inserted the Leopard Instal DVD and installed Boot Camp. I got a message right away saying that: "This program has known compatibility issues...". I clicked Run program and continued. Soon I got the same warning, but this time not for Boot Camp, but Intel Chipset Device Software. I clicked Run program yet again and it continued installing. Then I got a different warning: "Service KeyAgent' failed to start. Verify that you have sufficient privileges to start system services." I clicked Ignore and installation continued. I got another "Service Mac HAL' failed to start. Verify that you have sufficient privileges to start system services." warning, clicked Ignore again and after that it finished soon and I restarted the computer.
When I came back into Windows there was no Apple folder anywhere or any sign that I have just installed Boot Camp ( should there be? )
I installed Boot Camp Update 2.1 for Windows XP ( because Vista x64 version wouldn't start ) and basically I got the same warnings I did when I installed Boot Camp from the Leopard DVD ( described above ). I also tried to instal Boot Camp Update 2.2 for Windows, but it didn't start. I also downloaded Bluetooth Update 1.0, but all I got was a message saying: "This update is not intended for this computer and will not be installed.".
There is also no sound.
This is basically it, I really hope some of you who run Windows 7 with wireless keyboards and mice can help me, because I desperately need this to work ( I use a Windows only program for school ).
PS. I have a 2007 iMac 24" white and while it is not on the we're-not-supporting-that list for the infamous Windows 7 Boot Camp update, all other iMacs from its generation are. Any ideas?

Found a solution for the "Boot Camp x64 is unsupported on this computer model" message. Here is the link: http://www.techulous.com/hardware/how-to-apple-boot-camp-64-bit-for-windows-7-on -unsupported-macs.html
Everything works ( for ) now. Yay!

Curve 8330 Voice dialing and sound problems, Please help!

I got this black berry curve 8330 from a friend on the weekend to replace my broken Pearl. He said it worked fine but it sometimes had a voice dialing problem. After wiping all the personal data and activating the phone the voice dialing went nuts. Every 6 to 9 sec the voice dialing would activate with no sound. meaning you don't hear the lady voice say, "say a command". After reading many forums posts I download memmax and removed all VAD files. But I will still left with no sound. I went and did a test on the hardware and the speaker and microphone both worked fine. Puzzled I tried playing a ringtone, , it plays maybe the first second of the file and then the sounds goes away but I am able to get it back by press the Speaker/$ key. I then tried making a phone call and the phone was working just fine. About an hour later I tired calling someone and the issue had raisin again. This time I was unable to get the sound back. (I tried resetting many times with no success.) I could still play media files, but was unable to get sound making or receiving calls (this includes the other party not being able to hear me as well.) I tired changing profiles with no success. I then did some more reading and tried updating the OS. Once that was done and voice dialing had been reinstalled and started acting up again. SO I removed it and basically everything happened all over again. So right now I have a phone that I can’t make calls on but I can still text and use the internet. Does anyone know a solution to this problem? Should I try wiping the OS and reinstall or is this phone toast?

The msi nforce package 2.29 fixes the NVMCP.SYS error and turns it into a very rare system freeze. 8o
Very rare!
been waiting almost 9 months for this fix so i could pull the damm soundblaster out! :O

IMovie 11 export unsync, transition problem, and sound problem

Hi all. I have done a 1 hour and 36 min long movie on my weeding and it's made of around 80 "clips", where in some places the original sound is used and in some places external sound is placed instead. In some places iMovie text boxes is used and in some places the video has filters and slow motion (so a lot of random filters, effects, etc and chapters).
So my problem? 3 weeks ago I wanted to just test the video before doing everything done and exported it as mov HD1080 and it worked good on other devices. When improvements done I tried to export it again. But as it is now, when I export is, regardless if its to iDVD, iTunes, MOV HD720 or 1080, and regardless if its "finilized" first or not, or if its shared to "media library", the transitions is not working (un sync) and the sound is fading out to 0% during all the transitions before up to the original level.
I have for real exported the film more than 25 times and average export time is 6 hours due to the high quality and the time duration.
When just in the project view looking and listening, everything is just perfect. As soon as I finilize the project, or export it, even in the project preview it doesnt work. I also tested to install miDVD pro (10$) and WonderShare DVD Creator (39$) to just sharing the project to them, but the result was the same.
I just want to be able to export it as it is in the project.
I have macbook 13, moutain lion, iMovie 11
Any suggestions?
Thanks in advance!

I have iMovie '11 and cannot create a HD 1080p movie. I've got a 27" iMac with a 2.93 GHz Intel Core i7 processor (I purchased this computer last month). I tried like crazy to export the HD movie last night (it's one of the new trailers -- the one that looks like Indiana Jones & it's less than 1 minute long) but no dice due to a "HEAP" error. I tried to export the movie a couple of times this morning. It went a little further in the rendering until the HEAP error popped up again (this was from a fresh reboot). The really odd thing is that when I render it in HD 720p, my movie clips are black. No video. The built-in trailer stuff from iMovie '11 is there, just none of my clips show up (they're all black).

Viewing and sound problems

I am unable to use vision as any programme I try to watch freezes every 30 secs. The sound also goes at the same time. If I try to watch anything on You tube the same thing happens. I am unable to watch a video on email. My own recorded videos are fine. My broadband supply has become very on/off with regard to speed and quality. I have a constant orange status light and a flashing green ethernet light and no AP light on the box nearest the computer and home hub 2.0. In another room I have a constant orange light, flashing green ethernet and a constant green AP light. I have made no changes to warrant all the problems. I have filters on all necessary plugs. I have also spent hours checking, changing and swapping leads. I first contacted BT on the 12th April, the problems appeared to cease for a couple of days and then began again. I was subsequently informed that there is a problem locally.
As a hard working, night shift staff nurse I normally enjoy the programmes on catch up and i.player etc. I feel that this has gone on for long enough now. Can someone please advise me.

Welcome to this customer to customer forum.
To enable forum members to help you, please could you look at Helping forum members to help you which asks you to do a few checks first, and has some helpful hints.
When you have done that, please post the results here, so members can offer advice. Thank you.
There are some useful help pages here, for BT Broadband customers only, on my personal website.
BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones.

P45 platinum boot up usb and oc problems

greetings
i m using a 1.0 rev A2, e5200, corsair ddr1066, antec ea500, galaxy 250
its running 333*11.5(3831mhz) with memory at 1:1.6 (533mhz)
voltages are all at auto except 2.10 for the ddr1066
it is all stable however during booting up it freezes at "initializing usb.." message if i have my printer or game controller plugged(both usb)
cap lock and num lock dont flash and i have to hold the power button to turn it off.
i always have mouse and wifi modem connected via usb but they are not affected.
the problem doesnt exist if its not overclocked.
it sometimes doesnt freeze if its a restart.
the bios was 1.6 and ive tried the beta 1.7b9 which didnt solve, neither did upgrading to the current power unit
also tried disabling usb legacy but didnt help. disabling usb helped but obviously i m not able to use the devices.
besides this, i cant get higher fsb than 350 with both bios, didnt change voltage for northbridge(which i doubt if its needed for 400ish), i did lower multiplier and memory ratios to previous working clocks.
any experience related will be appreciated, let me know if further information needs to be provided
thanks

OK, you have a different CPU and that may be the limiting factor here. You can of course request the latest beta BIOS from MSI. I suggest you do that as it did wonders for my board.
Also can you check on your PSU there should be a label with the full PSU power specifications. Please check the 12V1 and 12V2 rails amps and the max combined amps for the 12V rails.

CRC Errors and Sound Problems

Everytime I try to install something from my CD drive I get CRC errors. I sometimes get sound distorsions when I'm playing but those are not permanent and the original sounds come back after a couple of minutes. Can you help me fix this.
Intel P4 2.6
MSI 865PE Neo2
Radeon 9800 Pro
OCZ EL DDR PC-3200 / 400MHZ / Platinum / Dual Channel (2x512)
Maxtor SATA 80 Gig
CD Rom Creative 52X
LG DVD / CD Writer Combo 16X / 52X

Quote
Originally posted by Starscream
I'm using Slow performance and I just bought my computer. The problems started the first time I tryed to install XP Pro and never stopped after that.
No offence.....
Gen copy of XP Pro???????
This does not sound like a MainBoard issue............???? But will help all I can.
Del

Mac Volume and Sound Problem in newly installed Windows

Hi Friends,
I intalled the Windows 8 Developer Edition using Bootcamp 4.0
My Mac Volume/Hard Disk is not displayed in "My Computer". I read it will display the Volume in read-only mode. Can anyone help in making the Volume show on Windows?
The sound is also not working. Any work-around?
Thank you.
Regards,
Ragu

You are familiar with beta testing? Ever?
It is ah, "normal" for audio to not work on Mac running Windows until YOU install an audio driver.
AppleHFS.sys and AppleMNT.sys were buggy with Windows 7 3.0 and 3.1
If you want, see what Paragon HFS 9.5 $19 and ask Paragon-Software about whether you can beta test their HFS driver.
Their CampTune 9.5 was just updated to support Lion.
I would also call Lion 7.1 still in the "early" stage and not fully ready - give it a couple updates like every other OS X release - in the 'final candidate+' stage too. The Boot Camp 4 drivers for Windows are better now than they were in July but still some rough spots and things missing.
And there was a firmware update for the MBP just this week, and that model has been through 3-4 minor chip revisions to the motherboards, some of which deas with support and bugs with SATA 3 affecting SSD support.

Connecting Mac Air to TV and sound problems

I have a Mac Air 13, 2011 and have connected it to my Sharp Aquos TX using the Mac HDMI adapter, I get picture on TV and computer but sound only on computer. What do I need to do in the settings?

Select your TV as the output device in System Preferences > Sound > Output tab > click on the TV.
You can also hold OPT as you click on the sound icon in the menubar to select the output device.
Regards,
Captfred

Windows driver for "Multimedia Controller" and sound problem

Hi
I installed Windows 8.1 using Bootcamp on my Macbook Air (Early 2014, Intel i5).
Then I downloaded Bootcamp drivers from http://support.apple.com/kb/dl1720 and installed couple of them (wifi, intel chipset).
When I check the Device Managmer I still get "Multimedia Controller" in "Other devices" without drivers.
Beside that I think the sound is not working. I installed the Realtek sound driver. When I play sound file the volume bar in taskbar mixer is blinking but no sound is coming out : ).
Please help.

for multimedia controller if its onboard sound card use this drivers:
http://download.nvidia.com/Windows/nForce/4.62/4.62_nforce_audio_winxp2k_international_whql.exe
but based on both:
multimedia controller
multimedia video controller
think its external PCI device like TV tuner.
get this one to ID the device: http://www.zhangduo.com/UnknownDeviceIdentifier.exe

USB and sound problems on a P10-221

Similar Messages

Maybe you are looking for