USB Compressor Mic Problem Help please
I plug in the usb compressor mic. Then I go and select it for my device. Next I select input 1 for my input and Out 1-2 for my out put under 0/l in the Audio 1 thing to the left of the screen. After it is selected I have no audio. As in, If I hit play nothing comes out, but I hit record and the mic records. Although the only way I can listen to what I have recorded is to select the built in mic for device. i need help cuz I cant hear the tempo or the instrumens when I record my vocals either. Please help. It is a MXL-Usb stereo compressor mic .007 if that helps
Try creating a Aggregated device in the Audio / MIDI set up utility. Use the mic as input and built-in for output. Then choose the aggregated device in logic express.
This should work.
Similar Messages
-
Can only sync iPhone/ipad through USB now not WiFi - help please?
can only sync iPhone/ipad through USB now not WiFi - help please?
Hi Iron Tommy,
If you are having issues syncing your devices to iTunes via WiFi, you may find the troubleshooting steps outlined in the following article helpful:
iTunes 10.5 and later: Troubleshooting iTunes Wi-Fi syncing
http://support.apple.com/kb/ts4062
Regards,
- Brenden -
I recently tried updating my iPad and while doing this, my internet connection faulted. since then my PC does not recognise my i Pad when connected through USB. Can anyone help please???
You may have to force your iPad into recovery mode in order to restore the device since the update did not complete. This article explains how to do that.
iPad: Unable to update or restore -
G710 usb 3.0 problem - help!!!
Dear all,
I just bought a Lenovo G710 17inch laptop. I installed Windows 7 Home Premium, and all drivers, all devices in device manager are recognized and claiming to be functioning.
I face a problem with the usb 3.0 port:
- when I plug in my brand new toshiba canvio 3.0 hard drive I receive a message that I need to format the drive before I can use it. This message keeps presenting itself for the whole time the disk is plugged in (like a million times). If I select format disk, then the message keeps re-appearing. The format window at first did not appear at all and an error message appeared. Now after I tried some things, the format window appears but when I try to format there is a message saying that windows was unable to format the disk. The disk is working fine at another pc with usb 3.0 ports and also fine at the 2.0 port of this pc.
-when I plug in my intenso 3.0 hard drive it is recognized okay, but there is ridiculusly slow file transfer. For example, a 98MB file is tranfered in 3secs via the usb 2.0 port but it needs like 5minutes via the 3.0!!! For larger files transfer is almost impossible, and the estimated waiting time keeps getting bigger. The disk is working fine at another pc with usb 3.0 ports.
- the port seems to be a usb 3.0 port, it is blue, disks light up blue when connected but they have the issues I described above
- service guys didn't fix it... :/
I have tried re-installing the drivers, looking for other drivers, and other solutions posted in this forum but the problem remains...I am open to suggestions!!!! Help please!! Thanks!I think the problem still lies in the drivers. Have you ever checked if the drivers you installed are totally compatible with your USB 3.0 or the devices? I've met several users who got the same problem with you. Now the key point is that you need to install the exact drivers for the USB 3.0. If you don't know whether the drivers are best-matched, you can have a try with DriveTheLife. It wil lhelp to automatically find the best drivers for your USB and then install the drivers. This article shows very clearly how to download and install USB drivers: http://www.drivethelife.com/windows-drivers/how-to-free-download-update-install-usb-driver-for-windo....
-
VIRUS PROBLEMS, HELP PLEASE???
I continue to have messages popping up saying my computer is infected. It wants me to cleanup and I have to register with Mac Shield 2.6. Pronograhic websites keep popping up. Anyone having this problem? Did not have this problem yesterday, but it's here today! There is also a Red Sheild on the top of the toolbar where it shows the time, battery life, etc. Right clicking on the sheild drops down Scan Now, Cleanup, Control Center, Scan, System Info, Settings, About, and Register. A pron site just popped up again! Need help Please!!
Fuony wrote:
The Mac Shield malware can come through Firefox too if you allow it to and you click on it!
Your exactly right, it is possible that if you visit a site and need the scripts to run for something that the malware that uses Javascript is on that site, then your going to be presented with it.
The thing is with the Firefox + NoScript combination defeats alot of the web side trickery the malware authors are using to get the malware to appear in the first place.
Also this "MacDefender" isn't the only malware making the rounds. There are some serious Flash vulnerabilities being hosted on hostile/adult websites that are running scripts for no apparent reason other than to try to infect your machine.
By running all scripts all the time, your computer is in a state as if you tried running across a busy highway blindfolded.
As a lifelong "MacHead" I can understand Apple loyalty, but if Apple isn't cutting the mustard on their browser security, rather place their users security at serious risk for the sake of convenience, then I have to think about using and recommending to others something else that is more secure.
As a example, I surf thousands of web pages a day, some on really nasty sites, yet I haven't seen this "MacDefender" appear on my computer. Even when I purposely visited links that people have submitted that had the malware. (I maintain a couple of bootable clones of my boot drive just in case) -
ICloud problems help please!
I have an iPhone 6 and during the setup I must have did something wrong and now I have my old iCloud account on it that I no longer remember the password, security questions, and no longer have the email address to that account. I think I was hacked and my password and security questions changed. I want to log out of iCloud and start using my current iCloud account. I know these are security measures, but how can I get logged out??? My iPhone is having problems since the latest update and now I can't make a call or text. I can't call apple support without a working number HELP Please.
Hello shelbyrecords,
Oh no! That sounds really frustrating. Unfortunately, if iCloud Find my iPhone Activation Lock is enabled on the device we’ll need to gain access to your previous Apple ID account to disable it. Based on the information you have provided, it sounds like you may need a personalized support experience to recover your previous Apple ID:
If you forgot your Apple ID password - Apple Support
http://support.apple.com/en-us/HT201487
Make sure that you’re entering the correct Apple ID. In most cases, your Apple ID is also the primary email address of your Apple ID account. If these steps didn't help you change your password, contact Apple Support.
Thanks,
Matt M. -
Soundtrack problems - help please
Help please. I tried doing a send to multi-track project from FCP with the base layer video option and kept getting the 'error sending selection to Soundtrack Pro' message. I did a search and the suggestion is that I have no disk space but I have over 600GB!
Then I tried a send with the full video and the file saved okay. However when I try to open the .stmp file, Soundtrack Pro starts and then freezes. I've tried opening in various ways.
Help please, I just cannot figure this out! What am I doing wrong?Not sure how much help this is, but since you're having problems with the layout, did you try deleting the layout file? MacintoshHD/users/username/Library/Application Support/Soundtrack Pro/Layouts
BTW, I found a BKiLifeConfiguration.plist in the following path:
MacintoshHD > Library > Application Support > ProApps > Internal Plug-ins > BrowserKit > iLife.bkplugin > Contents > Resources
Do you find it there? -
SQL INSERT problem - help please
Hello,
I'm having a problem with INSERT statement.
There is a "ShowFinal.jsp" page, which is a list of candidates who selected from the second
interview. The user picked some candidates from the list and conduct the 3rd interview. After
he check suitable candidates(who are selected from the 3rd interview) from the list , enter
basic salary for every selected candidate, enter date of interview and finally submit the form.
These data should be save into these tables.
FinalSelect(nicNo,date)
EmpSalary(nicNo,basicSal)
In this "ShowFinal.jsp" page, it validates the following conditions using JavaScript.
1) If the user submit the form without checking at least one checkbox, then the system should be
display an alert message ("Please select at least one candidate").
2) If the user submit the form without entering the basic salary of that candidate which was
checked, then the system should be display an alert message ("Please enter basic salary").
These are working well. But my problem is how to wrote the "AddNewFinal.jsp" page to save these
data into the db.
Here is my code which I have wrote. But it points an error.
"AddNewFinal.jsp"
String interviewDate = request.getParameter("date");
String[] value = request.getParameterValues("ChkNicno");
String[] bs = request.getParameterValues("basicSal");
String sql ="INSERT INTO finalselect (nicNo,date) VALUES(?,?)";
String sql2 ="INSERT INTO EmpSalary (nicNo,basicSal) VALUES(?,?)";
for(int i=0; i < value.length; i++){
String temp = value;
for(int x=0; x < bs.length; x++){
String basic = bs[x];
pstmt2 = connection.prepareStatement(sql2);
pstmt2.setString(1, temp);
pstmt2.setString(2, basic);
int RowCount1= pstmt2.executeUpdate();
pstmt1 = connection.prepareStatement(sql);
pstmt1.setString(1, temp);
pstmt1.setString(2, interviewDate);
int RowCount= pstmt1.executeUpdate();
Here is the code for "ShowFinal.jsp".
<form name="ShowFinal" method="POST" action="AddNewFinal.jsp" onsubmit="return checkEmpty() &&
ValidateDate();">
<%-- Loop through the list and print each item --%>
<%
int iCounter = 0; //counter for incremental value
while (igroups.hasNext()) {
Selection s = (Selection) igroups.next();
iCounter+=1; //increment
%>
<tr>
<td style="background-color:ivory" noWrap width="20">
<input type="checkbox" name="<%= "ChkNicno" + iCounter %>"
value="<%=s.getNicno()%>"></td>
<td style="background-color:ivory" noWrap width="39">
<%= s.getNicno() %> </td>
<td style="background-color:ivory" noWrap width="174">
<input type="text" name="<%= "basicSal" + iCounter %>" size="10"> </td>
</tr>
<%
%>
Date of interview<input type="text" name="date" size="17"></td>
<input type="submit" value="APPROVE CANDIDATE" name="B1" style="border: 1px solid #0000FF">
</form>........................................................
Here is the error generated by TOMCAT.
root cause
java.lang.NullPointerException
at org.apache.jsp.AddNewFinal_jsp._jspService(AddNewFinal_jsp.java:70)
at org.apache.jasper.runtime.HttpJspBase.service(HttpJspBase.java:137)
I have goto the file "AddNewFinal_jsp.java". The line 70 points to the following line.
for(int i=0; i < value.length; i++){ [/b]
Please can someone help me to solve this problem? Please help me to do this task.
Thanks.Hi Casabianca ,
It is clearly that your problem is not on the database end, more like a servlet/jsp issue.
I will not comment on the javascript portion, but rather the 2 jsps.
a simple way to trace what's go wrong is to check the final result (the html code) of the first jsp (showFinal.jsp), and compare against what is expected by the 2nd jsp (AddNewFinal.jsp). Most browser do provide "view source" on the page visited.
the following code
<input type="checkbox" name="<%= "ChkNicno" + iCounter %>" value="<%=s.getNicno() %>">
<input type="text" name="<%= "basicSal" + iCounter %>"
would likely to be "translated" to html code something as follow:
<input type="checkbox" name=""ChkNicno0" value="nicNo>">
<input type="text" name="basicSal0">
the original code in "AddNewFinal.jsp" using
request.getParameterValues("ChkNicno");
which looking for a none exist http request parameter (sent as "ChkNicno0",etc but look for "ChkNicno"), which has explained before.
the second attempt to use String[] value = request.getParameterValues("ChkNicno" + iCounter); give Cannot resolove symbol :iCounter. because iCounter never defined in the 2nd jsp!
Most of the error message do give clue to cause of error... : )
not too sure on your intension, assume you wish to update only those selected (checked) row to db.
some suggestions:
1) <input type="text" name="ChkNicno" size="10"> </td>...
<input type="text" name="basicSal" size="10"> instead.
then use javascript to based on checked element index (refer to javascript spec for more details), for those index not checked, clear off the correspond index "basicSal" field value.
e.g. ChkNicno[1] is not checked, empty basicSal[1] value before submission.
This will give us only selected rows values.
2) retain the code
String[] value = request.getParameterValues("ChkNicno");
String[] bs = request.getParameterValues("basicSal");at 2nd jsp, as now the http request will pass parameters using "ChkNicno" and "basicSal".
3) some change to the code for optimization
for(int i=0; i < value.length; i++){
String temp = value;
for(int x=0; x < bs.length; x++){
String basic = bs[x];
pstmt2 = connection.prepareStatement(sql2);
pstmt2.setString(1, temp);
pstmt2.setString(2, basic);
int RowCount1= pstmt2.executeUpdate();
pstmt1 = connection.prepareStatement(sql);
pstmt1.setString(1, temp);
pstmt1.setString(2, interviewDate);
int RowCount= pstmt1.executeUpdate();
to
pstmt1 = connection.prepareStatement(sql);
pstmt2 = connection.prepareStatement(sql2);
for(int i=0; i < value.length; i++){
String temp = value;
for(int x=0; x < bs.length; x++){
String basic = bs[x];
pstmt2.setString(1, temp);
pstmt2.setString(2, basic);
int RowCount1= pstmt2.executeUpdate();
pstmt1.setString(1, temp);
pstmt1.setString(2, interviewDate);
int RowCount= pstmt1.executeUpdate();
preparestatement created once should be sufficient as we do not change the sql statement throughout the loop.
there are better solutions out there, this just some ideas and suggestions.Do try out if you wish.
Hope it helps. : ) -
Multiselect problem Help please!!
Hi all,
I am currently using Application Express 3.1.2.00.02 I have developed an online questionnaire with a multiselect list for one of the questions. The problem i am having is that i need each choice to be totaled up separately on the report generated.
My table of answers looks like this:
Column name e.g. (Question 9)
Answer "Dog" "Cat" "Mouse" "Snake" (underneath column name Question 9 depending on what is selected).
The reporting page would look like below:
*(Column Question 9)* Count
Dog 1
Mouse 1
Snake 1
and for the question you could have another respondent who chooses similar of items on the multiselect, so their answer looks like this:
Answer
"Question 9" Dog
"Question 9" Snake
This would then start a new row on the reporting page like below which is not what i want:
*(Column Question 9)* Count
Dog 1
Mouse 1
Snake 1
Dog: Snake 1
But the report should look like this:
*(Column Question 9)* Count
Dog 2
Mouse 1
Snake 2
The current SQLquery i am using is below:
select "QUESTION 9",
count(*) c
from "P1 DQUESTIONNAIRE"
group by "QUESTION 9"
Thanks for your help and suggestions,
'S'How to make sure your forum post will never be answered:
1) Make sure your subject line is completely meaningless (i.e. HELP PLEASE!) and describes no part of your actual problem
2) State that you are having "a few problems" but make sure to offer no details whatsoever what those problems are or what the symptoms are.
3) Post large volumes of code instead of distilling the problem down to a compact snippet
4) For extra points, make the code hard to read by refusing to make use of the "code" tag. -
K8N Neo2-fx Ram problem Help please
I have three ram(2x512MB single sided , 1x1GB double sided). Is there any way I can put them all on the motherboard? When I place them all the computer is not starting and it`s making a "beep" every 2-3 seconds. If i connect the 1GB double sided on the Dimm1(green) and the one 512MB single sided on the Dimm3(green) it`s working properly. Is there any way I can use all my ram at the same time. I`m desperate. Help please... thank you
Quote from: wodahS on 09-November-06, 05:55:17
How can I put my computer facts under any post I am posting? I should make it my signature?
That's the rule mate which you need to gives all your component in details including your PSU and Bios revision so that others can help you! Like what BOSSKILLER say it won't works with 3 DIMMS unless you purhased another 1 GB of RAM then it can solve your problem with 4 DIMMS or else with 2*512MB RAM. Make sure that you've lowered your HT to <=800Mhz as default is 1000Mhz. GD luck. -
M-Audio USB + Shure Mic + GarageBand =FRUSTRATION please help!
Hi everyone,
Problem: My new M-Audio Fast Track USB interface isn't working for me. I've got it and a Shure microphone and I work in Garage band.
I installed the M-Audio software and drivers. In system preferences as well as GarageBand's preferences, I set the audio in and out to the Fast Track. I plugged in the Fast Track into my MacBook Pro's USB. The power indicator lit up.
I then plugged the mic into the guitar jack in the back of the interface using the proper fitting. The mic light didn't light up. I turned the mic's gain knob allll the way up and it barely flickered indicating a mic signal. I put my headphones into the FastTrack, created a new real audio track in GarageBand and tried recording. Test, test, test. I played it back and it was just static.
What's going wrong here? There was some speculation that the M-Audio didn't want to work with GarageBand. I tried installing the ProTools free trial that came with the FastTrack to see where the error was (GarageBand and M-Audio working together OR the unit itself.) No luck. Each time I clicked Pro Tools, the black curtain slowly descended and my computer shut down.
I'd really appreciate some help! Thanks everyone!
MacBook Pro Mac OS X (10.4.7) it kinda rules.I then plugged the mic into the guitar jack
You can't do that, it's the same reason as
http://thehangtime.com/gb/gbfaq2.html#micline -
Hi folks - I wonder if anyone can help. I am having real difficulty with USB on my system :O . My modem cuts out, my scanner won't scan and genrally the whole USB thing is getting to be a drag. It appears that the MB is the issue as I have tested the equipment on other machines and they work fine. My MB details are (from Sisoft Sandra)
SiSoftware Sandra
Entire System
Manufacturer : MSI
Model : MS-6195
Unique ID : FFFFFFFF-FFFFFFFF-FFFFFFFF-FFFFFFFF
System Mainboard
Manufacturer : MSI
MP Support : No
Model : MS-6195
Serial Number : 00000000
BIOS ID : 62-1800-001169-00101111-071595-IRONGATE
On-board Devices
Creative ES1373 : Sound Device
Memory Controller
Error Detection Method : None
Error Correction Capability : None
Supported/Current Memory Interleave : 1-way / 1-way
Number of Memory Slots : 2
Maximum Installable Memory : 512MB
Maximum Module Size : 256MB
Supported Memory Types : DIMM, SDRAM
Supported Memory Voltages : 3.3V
Physical/BIOS Memory Banks
DIMM1 M/B (RASL-0 RASL-1) : 128MB DIMM SDRAM double-bank
DIMM2 M/B (RASL-2 RASL-3) : 64MB DIMM SDRAM single-bank
System Chipset
Model : Advanced Micro Devices (AMD) AMD-751 (Irongate) CPU to PCI Bridge
Bus(es) : ISA AGP PCI USB FireWire/1394 SMBus/i2c
Front Side Bus Speed : 2x 101MHz (202MHz data rate)
Max FSB Speed / Max Memory Speed : 2x 100MHz / 1x 100MHz
In Order Queue Depth : 8 req(s)
Logical/Chipset Memory Banks
Bank 0 Setting : 64MB SDRAM 8-1-1-1R 6-1-1-1W 3-2-3CL
Bank 1 Setting : 64MB SDRAM 8-1-1-1R 6-1-1-1W 3-2-3CL
Bank 2 Setting : 64MB SDRAM 8-1-1-1R 6-1-1-1W 3-2-3CL
Bank 4 Setting : 64MB SDRAM 8-1-1-1R 6-1-1-1W 3-2-3CL
Bank 5 Setting : 64MB SDRAM 8-1-1-1R 6-1-1-1W 3-2-3CL
Speed : 1x 101MHz (101MHz data rate)
Multiplier : 1/1x
Power Down Mode : No
Fixed Hole Present : No
Memory Modules
Memory Module 1 : 128MB 16x(8Mx8) SDRAM PC133U-333-542 (CL3 upto 133MHz) (CL2 upto 100MHz)
Memory Module 2 : LGS GMM2649233CTG-7J 64MB 8x(8Mx8) SDRAM PC100-322-611 (CL3 upto 100MHz) (CL2 upto 67MHz)
Memory Module 3 : 128MB 16x(8Mx8) SDRAM PC100-222-622 (CL3 upto 125MHz) (CL2 upto 100MHz)
System Clock Generator
Model : ICS 9248-110
Software Programmable : Yes
Read-Back Support : Yes
Speed Selected By : Hardware
Spread Spectrum Modulated : No
No FSB Speeds : 32
FSB Speed Range : 90 - 150MHz
Environment Monitor 1
Model : Winbond W83782D SMB
Version : 3.00
Mainboard Specific Support : No
Temperature Sensor(s)
Board Temperature : 42.0°C / 107.6°F
CPU Temperature : 48.0°C / 118.4°F
Power / Aux Temperature : 33.5°C / 92.3°F
Cooling Device(s)
Auto Fan Speed Control : No
CPU Fan Speed : 5870rpm
Voltage Sensor(s)
CPU Core Voltage : 1.62V
Aux Voltage : 3.34V
+3.3V Voltage : 3.36V
+5V Voltage : 5.13V
+12V Voltage : 12.22V
-12V Voltage : -12.45V
-5V Voltage : -5.20V
AGP Bus
Version : 1.00
Speed : 67MHz
Current Data Transfer Rate : 1x 67MHz (67MHz data rate)
Max Data Transfer Rate : 2x
Side Band Enabled : No
Side Band Support : Yes
Fast-Writes Enabled : No
Aperture Size : 64MB
PCI Bus(es)
Version : 2.10
No Bridges : 1
PCI Bus 0 : 32-bit PCI (34MHz)
Multiplier : 1/3x
LPC Hub Controller 1
Model : Advanced Micro Devices (AMD) AMD-756 (Viper) PCI to ISA Bridge
ACPI PM Enabled : Yes
Random Number Generator Enabled : No
Speed Multiplier : 1/4x
Speed : 9MHz
DMA Multiplier : 1/2x
DMA Speed : 5MHz
USB Controller 1
Model : Advanced Micro Devices (AMD) AMD-756 USB Open Host Controller
Version : 1.00
OHCI Interface : Yes
Legacy Emulation Enabled : No
FireWire/1394 Controller 1
Model : Creative Labs Audigy IEEE1394 Firewire Controller
Version : 1.10
OHCI Interface : Yes
Enhanced 1394a Support : No
Channels : 64
Speed : 400MHz
System SMBus Controller 1
Model : AMD 75x/76x SMBus
Version : 0.03
Expansion Slot(s)
PCI1 (1h) : PCI 32-bit 5V 3.3V PME FullLength Available (Advanced Micro Devices (AMD) AMD-751 PCI to AGP Bridge)
PCI2 (2h) : PCI 32-bit 5V 3.3V PME FullLength InUse
PCI3 (3h) : PCI 32-bit 5V 3.3V PME FullLength Available
AGP : AGP-2x 32-bit 3.3V PME FullLength InUse
Port Connector(s)
Keyboard : Keyboard Port - None / PS/2
Mouse : Mouse Port - None / PS/2
Mic In : Audio Port - None / Mini-jack
Line In : Audio Port - None / Mini-jack
Line Out : Audio Port - None / Mini-jack
Serial Port 1 : Serial Port 16550A Compatible - None / DB-9 pin male
Serial Port 2 : Serial Port 16550A Compatible - None / DB-9 pin male
Parallel : Parallel Port ECP/EPP - None / DB25 pin female
USB 1 : USB - None / USB
J17 M/B - USB 2 : USB - Proprietary / USB
FDD M/B : None - Floppy / None
IDE1 M/B : None - ATA / None
IDE2 M/B : None - ATA / None
CDIN M/B : Audio Port - CD-ROM Sound Input / None
GamePort/MIDI : MIDI Port - None / DB-15 pin female
Bios is all up to date, drivers for modem and scanner all up to date - any ideas why the USB keeps cutting out?
The real drag is the only way to get USB back is to reboot. Any help gratefully received.
OS details are:
General OS Information
Windows System : Microsoft Windows XP Home Ver 5.01.2600
Full Name & Version : Microsoft Windows XP Ver 5.1 (Build 2600)
Kernel Type : Uniprocessor Free
Max. Licensed Processors : 1
BackOffice Components : No
Small Business Components : No
Terminal Services Components : No
Windows ID : 55285-011-7653275-21956
Registered Owner : Mark and Barbara
Registered Organisation : At Home
OS Properties
Debug Version : No
Security Present : No
Remote Terminal Session : No
GUI Effects Enabled : Yes
Boot Settings
Boot Type : Normal
OS Folders
Windows Folder : C:\WINDOWS
System Folder : C:\WINDOWS\System32
Programs Path : C:\WINDOWS\system32;C:\WINDOWS;C:\WINDOWS\System32\Wbem;C:\Program Files\SiSoftware\SiSoftware Sandra 2002 Professional
Temporary Folder : C:\DOCUME~1\Mark\LOCALS~1\Temp
Regional Settings
Country : United Kingdom
Language : English (United Kingdom)
Time Zone : GMT Standard Time
ANSI Code Page : 1252
OEM Code Page : 850
Rock Ape (UK) ) Thanks in advance.gilgaron is correct. power the hub and place the devices that require over 500ma on it-if the hub supports high power-which it should. look at your periphs you will notice that they have the power requirement listed on the sticker.
each individual root hubs only powers 500ma for all the ports not 500ma for each individual port. so the best bet usually is get a self powered hub and place the 500ma+ devices on it. also you may have the option of self powered device instead of usb power. that is also suggested if they need 500ma or more. -
Can't Upgrade to USB 2.0. Help Please!
I have an K7T266 Pro Version 1.0 motherboard. Have been trying for hours to upgrade the USB port to 2.0. Have followed all instructions from the MSI website.
Even upgrqaded my BIOS to 1.9 and still can't get it to work. When I try to install the USB 2.0 driver, I get a message that says "Driver Can't Start". I have up-to-date windows XP Professional Version with Service Pack 1. According to MSI, I should be able to upgrade but it just doesn't happen.
I remember being able to upgrade to USB 2.0 when the same system was under Win 98 Second Edition but just has not worked with Win XP. This is very important as I bought an external hard drive to use for making backups under Norton Ghost.
Can anyone please help me with this? I am sure some other users out there have had the same problem.
Thank You in advance...I have the same problems with this. THE KT6-Delta cd that came with my motherboard does not have the USB 2.0 drivers. It directs you to microsoft's website to install service pack one for XP or Win 2000. Then you can download an update from Microsoft for the USB 2.0. Is there any way to get around installing SP1? I currently only have access to dial up and that would take forever. Can someone give a link to some place that would have the drivers for USB 2.0?
-
Clean install mavericks failed. No bootable USB drive either. Help please.
HI guys I really would appreciate some help here.
i Saw on apples site how to do a clean install of mavericks. In disk utilities I erased my osx drive and began The download of a fresh copy. I didn't back up my files as I was going to manually install my applications etc. When the download finished and it tried installing mavericks it failed, I restarted as it was the only option and it failed again. I ran disk repair and it said everything was ok. I only have Internet access at the cafe near where I live so only have it during the day. I checked online with my iphone for similar troubles and found everyone mentioning making a bootable USB version but... As it did not say that on the mac website where it showed how to erase and install a clean copy I never made a USB copy. I'm left with my macbook not able to install my os. Please can anyone advise, I have no way of getting to a Genius Bar and there is no mac service repairs in my area.
I'm now using Internet recovery. I rebooted with option-command-r. A globe came up, I am now downloading mountain lion. Is this the right procedure now or am I wasting time as I only have a few hours left in the cafe with my macbook on? Thank you in advance.
Gregg
ps- I had mavericks up and running on my previously but wanted to basically clean my system of preference files, unwanted folders etc etc. Lesson learnt. I just need advice on the steps I must take to have my system working again .What you are doing now is the correct procedure, install the Mac OS X that came on the machine. From that you can have a working machine and then install Mavericks again.
Building a bootable/installable Mac OS X on a USB drive is time consuming and not necessary for most users...it is not difficult but it takes time and precision to get it right. Perhaps something to do in the future when you have the time.
Using a coffee shop internet connection is not a good idea for installing Mac OS X...you need a good, solid internet connection to do that, one that is reliable and offers sufficient bandwidth. But you don't have much option at this point since you say an Apple store and the genius bar is not available to you.
Finish the Mountain Lion install, reinstall your applications, get the Mac up and running well, then do the Mavericks install on top of the Mac OS X you have.
You would do well to get an external hard drive, great ones are available from OWC http://www.macsales.com and make a good backup of your entire system as soon as you are finished installing Mac OS X. If you make the external a bootable copy, such as by cloning with Carbon Copy Cloner or SuperDuper, you can always have a working computer...life will be much easier with that.
Good luck building Mountain Lion, and get the system running again before upgrading Mac OS X -
Shockwave Player 11 - Problem HELP PLEASE!!
I have upgraded to Shockwave Player 11 but I am having big
problems. I have installed it but when going on a Shockwave
supported sites ie; iSketch, it comes up in a white-box with a
message ''Adobe Shockwave Player is now installing.'' ''Installing
compatibility components.'' with a white bar below which is
supposed to fill up but doesnt. Screenshot on Link below. I have
been trying it both on IE7 & Firefox, tried both semi and full
installer but no luck. Please help?
http://i7.photobucket.com/albums/y295/ldndude/others/ShockwaveFlash11Problem.jpgquote:
This worked for me. It will actually let me access the game,
but it is unplayable. The drawings are all just random lines. When
I draw people see this problem, it looks like I am just drawing
random lines on the canvas.
I'm glad 4 helping u.4 me all the games r playable.But the
new ones like....
http://www.miniclip.com/games/power-boat/en/
or
http://www.miniclip.com/games/rally-championship/en/
r very slow.
Maybe you are looking for
-
How to get rid of the line encasing the left hand side of a vertical spry menu?
Hi, I have created a vertical spry menu bar. It all works but there is a line like this [ encasing the left hand side of the menu. Does anyone know how to get rid of this? Thanks!
-
How to divide different pictures into pie pieces so that they fit together in a circle
I have six photos that I need to divide into pie piece shapes so that they fit together in a perfect circle. How do I do this??
-
what is the difference between dedicated server mode and shared server mode.
-
Still have issues in APP CC with captions not showing
I tried to add to a discussion that was posted about this issue and for some reason couldn't. So, please pardon me for starting a new discussion. I've tried everything, read everything, implemented suggestions from others and still I cannot get my ca
-
Problem : REP-1352: The fonts specified for this report cannot be found for the character set specified by NLS_LANG. Secene : I am getting this runtime error after 3 years of usage only in a particular client. (This report works fine with other clien