USB Disk hanging my airport extreme

When I hook my Acomdata disk up to my airport extreme, I've had some weird issues. First time, it worked and I could see it without any problems. Second time, I hooked up another acomdata disk, one with firewire and USB connections (and full of iTunes.) That time, it locked up the router immediately. After another hard reset I then plugged the original (empty) USB only disk in, and it wouldn't be seen. I formatted the drive as fat32 ( want to share my iTunes DB with PCs.) When the disk was empty, it worked as expected (but clients wouldn't see it from the utility - i had to mount it manually - that's another issue.) I copied over my 70GB of music, and it worked fine. As soon as I tried to access it, it locked up my router again. The USB drive is OK, as i've used it successfully on several different systems, and it's now sharing my music very well on my lone windows box.
Any suggestions? I've heard the 7.1 firmware causes issues with USB drives. I've also heard that some USB/firewire chipsets cause problems. After each lockup, I had to do a hard reboot - I don't mention it each time. Lastly, I don't remember where in the process above I upgraded my firmware.
Thanks for any advice you might offer.
Greg Cain
[email protected]
Many Mac OS X (10.4.9)
Many Mac OS X (10.4.9)
Many Mac OS X (10.4.9)

run the following terminal command
sudo chflags 0 /Volumes/*
you'll have to enter your admin password (which you won't see). that's normal.

Similar Messages

Setting up USB disks connected to Airport Extreme

I took two different USB drives, formatted one drive with two partitions of Mac OS Extended (journaled) and the other drive formatted NTFS. After attaching the drives to the AE, I established how I wanted to share the devices and set up accounts to access the devices. My intention was to use these drives to backup my devices but have since learned that Time Machine does not support this (stupid and disappointing).
When I log in from my Mac, I see the one drive with two partitions, but I also see a drive with my account name. Performing a "Get Info" on the drives now show their format as AppleShare. What feature did I invoke that automatically established a "third" drive? Where is it established on the physically formatted Mac drive? Does the format of Appleshare just indicate how the partition is accessed?
The other account, established for a Windows machine, does not see the NTFS drive, but when logging in to the AE also has a drive mapped with the name of the account. I also cannot consistently connect to this drive as the airport utility does not display the drive in the system tray. The airport utility doesn't see the AE, yet this Windows device can print just fine to the printers attached to the AE.
I'm dazed and confused. Can anyone explain what is going on? Thanks.

The USB port on the AirPort Extreme will support drive formats of Mac OS Extended (Journaled) and FAT32. NTFS is not supported, so that might explain some of your difficulties.
What feature did I invoke that automatically established a "third" drive? Where is it established on the physically formatted Mac drive? Does the format of Appleshare just indicate how the partition is accessed?
Not sure about this. When I format a drive as Mac OS or FAT 32, I see a single drive when accessed from the Finder.

How do I restrict access to USB Disk connected to Airport Extreme

I have attached a USB HDD to my Airport Extreme Base Station. The drive is divided into 4 partitions, which I did with the HDD connected directly to a MBP before plugging into the AEBS. All the Macs on the network seem to be able to read and write into all 4 partitions. Is there anyway to restrict which Macs can access with partition? Or, if I went to a single partition, is there a way to restrict access on a folder by folder basis?
I've tried searching, but the best answer I've found so far is that the AEBS will only support a single partition/volume.... which doesn't appear to be true anymore.
Thanks in advance

You can put a filter on your wifi or use something like the K9 browser.

Unable to view *certain* folders on a USB disk shared by Airport Extreme

I have a 1 TB FAT32 formatted USB drive shared over an Airport Extreme (firmware 7.4.2).
A few days ago I was reorganising media files on the hard drive. I created a subfolder in a folder called 'Movies' and copied a couple of VOB files into the subfolder. Suddenly, the entire contents of the 'Movies' folder vanished. I unmounted and re-mounted the shared disk on the Mac (browsing to the base station in finder and clicking eject). I am able to see all other top level folders and other files on the shared drive, but the 'Movies' folder is empty. The Airport logs indicated a problem with the volume, so I disconnected the drive from the airport, plugged it into the mac and ran disk utility to verify the disk. No errors were reported.
Here is where it gets interesting.
1) When I plug the USB drive into my Macbook Pro, I am able to mount the drive and browse all the directories, including the Movies folder - all my files are still there.
2) If I plug the disk back into the airport and mount it on the mac, the 'Movies' folder appears empty.
3) The hard disk usage reported (both in the airport utility and in finder) is consistent with the 'Movies' folder still being there, however the Movies folder shows up at Zero bytes in 'Get Info'
4) If I open a terminal window and cd to the mounted hard disk, 'ls -al' reports no files. However, I can 'cd' to a sub-directory of the Movies folder that I know exists, and 'ls' shows all the files in the sub folder!
I can even copy files in the 'Movies' folder to another location if I know then name - but 'ls' cannot see it, and neither can 'du'
5) I attached the drive to a Windows machine and ran chkdsk and even did a surface scan - no problems reported.
I'm stumped. Has anyone seen this wierd behaviour before? The disk is fine when mounted directly on a mac or windows machine - but when mounted and shared via the airport, the Movies folder is not visible, though it is definitely there!
Help appreciated!

Hello nikkjazz. Welcome to the Apple Discussions!
The 802.11n AirPort Extreme Base Station (AEBSn) supports USB storage devices that use a block size of 512 bytes ... and is true whether the device is formatted for HFS+, FAT16 or FAT32. If yours is not, then it may explain why you can see the folders when the drive is directly attached to the Mac, but not so when connected to the AEBSn.

Deleted files from USB Disk attached to Airport Extreme

I deleted files from a USB disk attached to my airport extreme. I then needed to recover them but they are not in the trash can...how can I find and restore these files? I have not emptied the trash. I am just looking in the trash in my bar at the bottom bar. I got the message that asked if I wanted to send them to the trash and I said yes...help, I need the files!
Thanks,
Josh

Unfortunately, as the message clearly states.....the file(s) will be deleted immediately....not moved to the trash.
If you want to experiment, a utility like Disk Warrior might be able to salvage some of the data on the disk....IF....you have not made any changes on the disk since you deleted the files.
http://www.alsoft.com/diskwarrior/
But, it will be much quicker to simply restore a copy of the file(s) from your backups.

Can Time Machine back up a USB Drive connected to Airport Extreme?

If I connect 2 USB drives to an Airport Extreme via a USB hub, can I use Time Machine to back one up to the other? I've found multiple discussions about how to use an Airport Extreme disk as a Time Machine backup disk, but nothing on this. I want to use one disk as network storage (i.e. use the Airport extreme as a NAS), but I need a backup solution for that disk.

That's disappointing. I actually have a separate NAS already, configured for RAID1: a ZyXEL NSA220. Worked fine when I only had windows machines, but isn't reliable with my MACs, and doesn't support extended journaled format, so I need a different solution. I was hoping to just use a USB drive attached to my airport extreme to replace it, but I can't do that if I can't back up that USB drive.
Can anyone recommend a good backup solution? Surely this can't be that uncommon a scenario?

Setup of USB Hard Drive on Airport Extreme for Time Machine

Hi all,
I upgraded to Mountain Lion a while back and am running the latest Airport Utility. Here's the problem: I can't get Time Machine to work anymore with my USB Hard Drive attached to my Airport Extreme. Is this setup no longer possible under Mountain Lion? Do I have to buy a Time Capsule? For the last couple of years I've had two MacBooks backing up with no problem to the USB drive connected to the Airport Extreme. Any advice would be appreciated!
Thanks,
Chris

While you can do this as Kappy points out, there a few details that you might want to consider before you make the move.
1) Time Machine backups to a drive at the USB port of the AirPort Extreme are not supported by Apple. While this does seem to work for some users, others (like me) have difficulty with corruption issues. The bottom line is that this is not a reliable method to back up your important data....and, no support or help from Apple if you do have difficulties.
Reference this Apple Support Document to confirm:
"Time Machine can’t back up to an external disk connected to an AirPort Extreme......"
http://docs.info.apple.com/article.html?path=Mac/10.6/en/15139.html
2) If you move the iPhoto library to the hard drive attached to the AirPort Extreme....your original or master library now resides on that disk.....and you have no backup for the library.....when, not if.....the drive has a problem.
3) You might want to post in the iPhoto forum to ask if it is still an iPhoto requirement that only one user at a time can have iPhoto open with the shared library arrangement.

Cannot connect to USB disk connected to Airport

I have a USB disk connected to the USB port on my Airport Extreme. The disk has a volume label already set and had been previously directly connected to my IMac
I've gone into the Airport utility and updated the 'Disks' information to include "Enable file sharing" and "Secure Shared Disks" "With Accounts". I have the users listed under acounts and have set the passwords, same as login passwords.
But, I can't successfully login to the disk. I've tried the base station password, the network access pasword, the user password: none work.
What am I missing here?

Does the disk appear as a volume when you check using the Disk tab in AirPort Utillity? In the example below, a WD Drive is connected to the USB port of an AirPort Extreme.
If the drive does not appear here first, you will not be able to access it. Check to make sure that the drive is formatted in Mac OS Extended (Journaled). FAT32 will also work as well.
Some other formats like NTFS or exFAT might be able to be read when the drive is connected directly to a Mac.....but these formats are not supported with the USB port on the AirPort Extreme.
If the drive is formatted correctly, try using a powered USB hub. Connect the powered hub to the USB port on the Extreme, then connect the drive to the powered hub.

HT1331 cant see disks in the airport extreme setup

cant see disks in the airport extreme "partions" to set up, tried different disks, cables, restart, etc, bottom line the extreme does not see any attached external hard drives, any ideas?
Cheers
Michael

Checklist:
1) The drive must be formatted in Mac OS Extended (Journaled). Unless the documentation with your drive specifically states this fact, the drive is very likely pre-formatted for Windows, which will not work on the AirPort Extreme. Use Disk Utility on your Mac to reformat the drive.
2) Even if the drive is formatted correctly, the USB port on the Extreme is underpowered....so it is often necessary to use a powered USB hub with the Extreme.....even if your hard drive has its own power supply.
3) The hard drive will not "show up" on the desktop the way that drive that is connected directly to the Mac will do. You must click on the AirPort Extreme icon under the SHARED heading in the Finder, then double click the folder representing the drive to mount it on the desktop.

Can't access my Seagate USB HDD on my Airport Extreme

I can not access my 1TB Seagate Freeagent USB Harddrive over the working AEBS network. Hoping to be able to share and stream files to all remote laptops in the house. I have the HD connected to the AEBS and the AEBS client identifies the HD under Disks by name with the correct information. It's set for file sharing and Share Over the WAN. The workgroup is set to WORKGROUP to match my laptop and I've also gone into Windows and dissabled Windows Search per other suggestions on another discussion.
All that said and done, I still can not see or access the HD via my Win7 laptop. I see there are tons of disscussions on this issue and seams many are frustrated because the meager AEBS instructions that come with the unit simply say "Connect the hard disk to the AirPort Extreme USB port using a USB cable. Open AirPort extreme utility, select your base station, and then click Continue. Follow the onscreen instructions to create a new network, if you have not already set up your network." which I already have. Do I need to do this again? Are there any other settings I can do in my Win7 system or in the AEBS system to be able to access my ext HD? I really don't want to format the HD as some users are talking about.
Any thoughts or suggestions woudl be helpful. This was a main selling point for me deciding to buy this router.
Thank you much.

Update...I've also formated my USB HDD to exFAT and still can not access it via the network. It is still completely visable in the AEBS client software. MAC OS was not an option for formating. I thought that exFAT would work since its the newer type of FAT32. Is there a program I can download to format the drive to a MAC OS format and then be able to acces the drive on my four Win7 PC's?
I'm at my wits end with this AEBS and am ready to pull the plug and take it back for an exchange to a Cisco Linux 4200. Please let me know if there is hope for a fix.

What's the most recent opinion about Time Machine backups to Hard Drives connected to the USB port on the Airport Extreme Base Station (5th generation)?

I have been searching the Apple communities and Internet for a final answer. I just bought an Airport Extreme Base Station (5th generation) and LaCie d2 quadra 1TB external drive as a replacement for TWO failed Time Capsules, neither of which Apple would replace due to failed power supplies. I formatted the 1TB drive using Disk Utility (Mac OS extended (journaled)) from my MacBook Pro, and then plugged into the Airport Extreme Base Station USB port. The Airport Extreme Base Station see the Hard Drive, and my MacBook Pro sees the Hard Drive in my finder under shared resources. Time Machine, however, does not see the drive. Is there a solution for this problem? If Time Machine will not work, is there another software product out there that will work, like Carbon Copy. Having to plug the backup drive into the USB port of your laptop every evening kind of defeats the purpose of having a laptop. Any suggestions would be appreciated.

Keeping in mind that this is not supported by Apple, I have been successful at doing the following:
1) Format the entire drive (1 Partition) as Mac Extended (Journaled). You must click in Options and set it as a GUID Partition Table (first option)
2) Plug drive via USB to AEBS
3) Using Airport Utility, use Manual Setup, then under Disks, select the new Disk and click File Sharing, then Enable File Sharing and Secured Shared Disks (recommended, of course). Other settings are up to you.
4) IMPORTANT: you will NOT see this Disk in Time Machine until you open Finder and double-click on it. You will not need to do this again (hopefully).
5) Now it should appear in Time Machine. Remember to exclude any large files like Virtual Machines, since they will be re-backed-up (is that a word?) every time it changes in any way.
6) Remember that the first backup (over WiFi) is the longest. Leave the computer alone during this period.
Good luck, and let us all know how it went for you!

I have a HP Laserjet P1102w printer hooked up to the USB port of my Airport Extreme. I'm able to print to the printer wirelessly from my MacBook Pro. My iPad (2nd gen) can't find the printer. What do I need to do?

My iPad is on the same network as the Airport Extreme. The HP printer is on the list of Airprint printers but I'm not using it as a wireless printer, per se, as it's hooked up to the USB port on the Airport Extreme.
I installed the HP ePrint app on my iPad. Unfortunately, the app could not find the printer either.
As mentioned earlier, I'm able to print wirelessly to the HP printer via my MacBook Pro.

ApplePearApple wrote:
Since I'm able to print to the HP printer from my MacBook Pro using this configuration, shouldn't I be able to print to the printer from my iPad, especially when all of the devices are on/using the same network?
Not necessarily. AirPrint uses a protocol separate from the communication protocol used for the Extreme's USB port. The HP printer may disable AirPrint when its USB port connected to a valid device, which is my reason for recommending you use it wirelessly.
From AirPrint Basics:
AirPrint printers connected using Bluetooth or shared through a USB port of a Mac, PC, AirPort Base Station, or Time Capsule are not supported.
AirPrint printers connected by Ethernet are supported in OS X.
You may get more competent assistance from HP. See this HP support forum topic: iPhone & iPad can't Airprint to p1102w LaserJet
HP's Mac support has always been miserable though. I have been much happier since I abandoned HP and started buying Brother printers. They just work.

Setting up USB External Drive to Airport Extreme Base Station

I've attached an External Hard Drive to my AEBS. My base computer is connected to the AEBS via Ethernet Cable and can see the external drive under Networked Drive however it shows up twice as Drive Y and Drive Z both showing the exact same capacity.
My desktop computer is running windows vista, and my laptop is also running vista. My Laptop connects to the AEBS wirelessly. The laptop does not see this External Hard Drive. How do I get my laptop to recognize this drive? Shoule my external hard drive display with two different drive letters, or should it only appear as one? I've not had much luck using this feature of the airport extreme and was the basic reason i purchased the AEBS

The USB port on the AirPort Extreme will support drive formats of Mac OS Extended (Journaled) and FAT32. NTFS is not supported, so that might explain some of your difficulties.
What feature did I invoke that automatically established a "third" drive? Where is it established on the physically formatted Mac drive? Does the format of Appleshare just indicate how the partition is accessed?
Not sure about this. When I format a drive as Mac OS or FAT 32, I see a single drive when accessed from the Finder.

Can I connect a 4 TB USB drive to the airport extreme and use it as a network drive for Time Machine

Can I connect a 4 TB USB drive to the airport extreme and use it as a network drive for Time Machine

Yes, if the drive is formatted in Mac OS Extended (Journaled).
The USB port on the Time Capsule is under powered, so you may need use a powered USB hub with the 4 TB drive...even if it has its own power supply.

Can't use my HP Deskjet F4580 Wireless Printer with the AirPort Extreme Base. The printer is NOT connected at the USB port of the AirPort Extreme, and is placed in another room. It worked just fine with my previous router (Linksys WRT54G). Help me!

Hey Guys!
I just got my AirPort Extreme Base, but I can't use my HP Deskjet F4580 wireless printer with it.
The printer is not connected to the AirPort Extreme's USB port. It is placed in another room, and I'd like to use it (the printer) wirelessly (not connected to the USB port os the AirPort Extreme), as I used to. There is no place for the printer close the AirPort Extreme. It worked just fine with my previous wireless router (Linksys WRT54G). I'm very disappointed with the AirPort Extreme Base Station because of that!...
Can you help me? Please?!
Thanks Folks!

This must be a tough one, no suggestions at all.

USB Disk hanging my airport extreme

Similar Messages

Maybe you are looking for