USB Drive Doesn't Appear Anywhere
This flash drive isn't visible on the desktop, in the finder, in Disk Utility. I know if I eject it by just pulling it out, I will get the message that it may have been damaged. I don't know what to do. Any ideas?
In Finder, Finder menu, Preferences, General, Show these items on the desktop. Put a check mark in External Disks. (And the others, if you also want them visible.)
...in Disk Utility...
If it isn't visible in Disk Utility, then you may have other issues with the flash drive. Have you tried a different flash drive on the same computer? The same USB port? Have you tried the non-mounting flash drive on a different Mac? (Or PC, if it's in a compatible format.) If it's not showing up at all, you may have no choice except to pull it out. If you're really worried, then you can shut down your Mac before pulling out the flash drive. (Shut down, not sleep.) That will ensure that the Mac will close and unmount the drive as best it can.
Similar Messages
-
External usb drive doesn't appear correctly connected via usb to Time Capsule
After using it successfully for months over my home LAN by connecting it via FW800 (and suing filesharing) to a stationary MacBook Pro, I'm attempting to connect a 2 TB Hitachi Deskstar 7K2000 hard drive (in a Rosewill quad-interface enclosure with Oxford semiconductor bridge chip) via USB cable to my third-generation Time Capsule. It is formatted as HFS+ with a GUID partition table.
It appears in Airport Utility and mounts correctly, but none of its folders appears. Have tried two different USB cables with the same results.
Any ideas as to what could be wrong?So do I. I have a 350 GB Maxtor One Touch external harddrive. When I boot the mac, the drive doesn't show. And if I run the AirPort Disk Utility, it shows by name. But no matter what settings I chose, it doesn't mount and it says "No Disk Found" in the menu.
But here comes the interesting bit: If I turn off the harddrive, and turn it back on again, AirPort Disk Utility finds it. So I think the problem has to do with the harddrive spinning down and going into sleep-mode. For some reason it seems to become invisible to the Extreme-box when doing so. But if that's correct, what the heck do I do about it? -
Often when I plug my USB drive (Seagate) into the USB port, it does not appear in the Finder. I have to reboot the computer for it to appear. Is there a reason why this happens, and is there anything I can do besides reboot?
thanks
ScottUSB and FireWire Quick Assist
http://support.apple.com/kb/HT1151?viewlocale=en_US
Common fixes for USB device issues (unrecognized, etc.)
http://www.macfixit.com/article.php?story=20070824012114701
Cheers, Tom -
When I press "select backup location" in the Time Machine section of System Preferences, my external hard drive doesn't appear as an option. How do I change this? My external hard drive is a FreeAgent GoFlex Drive.
Hi, what Format is the external Drive?
They usually come PC Formatted for Fat32/MSdos, or NTFS... is there anything on it now?
How to format your disks...
http://www.kenstone.net/fcp_homepage/partitioning_tiger.html
(To Install OSX on an IntelMac the Drive it needs the GUID Partitioning scheme mentioned at the bottom.)
Thanks to Pondini, Formatting, Partitioning, Verifying, and Repairing Disks...
http://Pondini.org/OSX/DU.html -
When I install Windows 8 on my MacBook Pro(13-inch,Early2011),the Super DVD Drive doesn't appear in Windows 8 and installing Boot Camp 5 drivers doesn't solve my problem,what can I do?
Go into your system preferences and click the startup disk icon then select your Mac HD.
-
With the new update of iTunes I can't sync the iPhone, it doesn't appear anywhere, how can I solve this?
Pages 5 now uses the system-level auto-correction in System Preferences > Keyboard > Text. Unfortunately, a lot of the options available in previous versions of Pages no longer exist.
Leave feedback for the Pages team using the link in the Pages menu. Also leave feedback for Mavericks. -
How can i take off the CD when it doesn´t appear anywhere??
there is a cd inside de computer and i try to eject it out and i can´t. it doesn´t appear anywhere.
I can´t record anything, and when i try to record any song it is said that the capacity is full.Hi Andere
The CD could be hidden on your desktop
Click on the desktop and press command-,
Where it says "Show these items on the desktop" make sure that "CDs, DVDs, and iPods" is checked.
Open disk utility and see if the disk is recognized.
If it is select it and click eject. -
My screen had a black out and since then, my ipod touch is not getting started. it just shows ' connect ipod to itunes'. Even after doing that, my Itouch doesn't appear anywhere in Itunes. Help !! ??
Try:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Reset all settings
Go to Settings > General > Reset and tap Reset All Settings.
All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
- Restore from backup. See:
iOS: How to back up
- Restore to factory settings/new iOS device.
- Make an appointment at the Genius Bar of an Apple store.
Apple Retail Store - Genius Bar -
when I put an appointment in the calendar on my iPhone, the appointment doesn't appear anywhere on my computers. iphone is
turned on everywhere, but the new appointment isn't showing up.Check the calendar you are creating events in on your phone is an iCloud calendar, only iCloud calendars will sync.
-
External Hard Drive doesn't appear!
Hey guys,
Wondered if you could help me out with this problem.
I have a Maxtor One Touch III drive and when I plug it in it doesn't appear on the screen. I go to disk utility and can't find it there either.
However, when I plug it into other computers - mac, p.c. etc it shows up.
Initially it did work for me but then mysteriously this problem surfaced..
I've called Seagate/Maxtor and still no luck...
Any idea of what I can try?
Duane GibsonOne option is to connect it through a powered USB hub. The additional power the drive will get from the hub may make all the difference.
-
External Hard Drive Doesn't Appear and Makes a Beeping Sound
I have a Mobile XXS external hard drive from Freecom (approx 460 GB) that works fine on my father's G3 iBook, but when I plug it into my G4 Aluminum Powerbook (OS 10.5) it runs, but doesn't appear on the desktop. It also makes a continuous beeping sound. I want to back up all my music projects. As far as I know the USB ports work because I'm able to use my iPod. This isn't an Apple product but the Freecom website doesn't have a very active forum. I was wondering if anyone had any experience with something like this. I appreciate any help.
It sounds like a USB-only hard drive, and the Powerbook G4 is notorious for not providing enough power for many external USB drives.
The usual suggestions are:
-Try a double (Y-style) USB cable to draw power from two ports for the drive
-Add a mains power adapter to the drive, if possible
-Try using the drive through a powered USB hub
Firewire drives don't seem to suffer from this problem. -
External hard drive doesn't appear in /dev/sd*
My 7 month old external hard drive (http://www.newegg.com/Product/Product.a … 6822136471) doesn't seem to work anymore. It doesn't appear in /dev/sd* nor 'sudo lsusb'. It used to work fine. I've tried multiple usb ports, multiple computers, and multiple OS (linux and windows). Any ideas what I could try next? Are there any tools to diagnose the problem further?
My last resort options are
1) take the drive apart and plug it into a desktop computer (probably invalidates warranty)
2) pay for data recovery (it's a personal hard drive. i'm not sure if this is overkill or expensive)
Any advice?Using a data recovery service might get a little expensive, it all depends on how important the data is and how much it will cost you to generate it again or replace it.
If the recovery job is simple as in just taking the disk out of the enclosure and copying the data to another disk then I guess it might not be too expensive. Some data recovery companies do provide a (free?) quote on how much it will cost you and others even state how much the more common data recovery tasks cost. If the data recovery company has an agreement with the disk manufacturer then the warranty will not be void and you can claim it and get a new disk.
If you plan to do it yourself be ready to make a full disk image and then copy your data out of the image (look into ddrescue and sparse disk images, works wonder if the disk is not too full), you don't know the cause of the controller failure and it might be that the hard disk is not in good shape too and will only live long enough to reliably extract all the data or do a full disk image a couple of times. -
Hi all,
Are anybody maybe encounter with problem after installation of imaq usb driver, the usb imaq palet doesn't appear :-(
Outside the Labview I succeed to connect by Vision Assistant but in VI Vision Assistant doesn't see usb camera.
Thank you in advance fore help.
YanHi Yan,
This happened to me also. I have two versions of LabView, 8.5.1 activated and 8.6 Evaluation. I installed the driver like three times but I only tried with LabView 8.6 and no palet appeared. Finally, i tried in 8.5.1 activated and it was fine and working properly. If you have more than one version of LabView, my advice is to check them all and see in which one the palet is visible. Other than that, i can't really think of anything else.
Hope this helps,
Sabin -
Hi
I've installed arch in the last few days, everything is almost fine.
The only problem is about the usb devices (like my pen and mobile modem). The system finds them, but they doesn't appear in /dev/sdX
lsusb shows me that the usb is there, but nothing else happens.
dmesg shows me this:
usb 2-2: new high speed USB device using ehci_hcd and address 2
usb 2-2: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
scsi2 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usbcore: deregistering interface driver usb-storage
lsmod | grep usb
btusb 9768 0
bluetooth 44621 1 btusb
usbserial 27170 0
usbcore 118921 6 uvcvideo,btusb,uhci_hcd,ehci_hcd,usbserial
My user is in storage group.
And i can mount CD and DVD.
If anything else is needed i will post here.
Can anyone help me?
thnaksif you run
udevadm info
in a terminal and then insert a usb drive, what is displayed?
I just tried on my computer, and I got the following:
[rene@ArchLounge ~]$ udevadm monitor
monitor will print the received events for:
UDEV - the event which udev sends out after rule processing
KERNEL - the kernel uevent
KERNEL[1264631862.534890] add /devices/pci0000:00/0000:00:02.1/usb1/1-1 (usb)
KERNEL[1264631862.535070] add /devices/pci0000:00/0000:00:02.1/usb1/1-1/1-1:1.0 (usb)
KERNEL[1264631862.535281] add /devices/pci0000:00/0000:00:02.1/usb1/1-1/1-1:1.0/host10 (scsi)
KERNEL[1264631862.535306] add /devices/pci0000:00/0000:00:02.1/usb1/1-1/1-1:1.0/host10/scsi_host/host10 (scsi_host)
UDEV [1264631862.545583] add /devices/pci0000:00/0000:00:02.1/usb1/1-1 (usb)
UDEV [1264631862.545810] add /devices/pci0000:00/0000:00:02.1/usb1/1-1/1-1:1.0 (usb)
UDEV [1264631862.545897] add /devices/pci0000:00/0000:00:02.1/usb1/1-1/1-1:1.0/host10 (scsi)
UDEV [1264631862.546004] add /devices/pci0000:00/0000:00:02.1/usb1/1-1/1-1:1.0/host10/scsi_host/host10 (scsi_host)
KERNEL[1264631867.534455] add /devices/pci0000:00/0000:00:02.1/usb1/1-1/1-1:1.0/host10/target10:0:0 (scsi)
KERNEL[1264631867.534481] add /devices/pci0000:00/0000:00:02.1/usb1/1-1/1-1:1.0/host10/target10:0:0/10:0:0:0 (scsi)
KERNEL[1264631867.534492] add /devices/pci0000:00/0000:00:02.1/usb1/1-1/1-1:1.0/host10/target10:0:0/10:0:0:0/scsi_disk/10:0:0:0 (scsi_disk)
KERNEL[1264631867.534502] add /devices/pci0000:00/0000:00:02.1/usb1/1-1/1-1:1.0/host10/target10:0:0/10:0:0:0/scsi_device/10:0:0:0 (scsi_device)
KERNEL[1264631867.534655] add /devices/pci0000:00/0000:00:02.1/usb1/1-1/1-1:1.0/host10/target10:0:0/10:0:0:0/scsi_generic/sg5 (scsi_generic)
KERNEL[1264631867.534680] add /devices/pci0000:00/0000:00:02.1/usb1/1-1/1-1:1.0/host10/target10:0:0/10:0:0:0/bsg/10:0:0:0 (bsg)
UDEV [1264631867.534920] add /devices/pci0000:00/0000:00:02.1/usb1/1-1/1-1:1.0/host10/target10:0:0 (scsi)
UDEV [1264631867.536591] add /devices/pci0000:00/0000:00:02.1/usb1/1-1/1-1:1.0/host10/target10:0:0/10:0:0:0 (scsi)
UDEV [1264631867.536612] add /devices/pci0000:00/0000:00:02.1/usb1/1-1/1-1:1.0/host10/target10:0:0/10:0:0:0/scsi_disk/10:0:0:0 (scsi_disk)
UDEV [1264631867.536623] add /devices/pci0000:00/0000:00:02.1/usb1/1-1/1-1:1.0/host10/target10:0:0/10:0:0:0/scsi_device/10:0:0:0 (scsi_device)
KERNEL[1264631867.537005] change /devices/pci0000:00/0000:00:02.1/usb1/1-1/1-1:1.0/host10/target10:0:0/10:0:0:0 (scsi)
UDEV [1264631867.538299] add /devices/pci0000:00/0000:00:02.1/usb1/1-1/1-1:1.0/host10/target10:0:0/10:0:0:0/scsi_generic/sg5 (scsi_generic)
UDEV [1264631867.538721] add /devices/pci0000:00/0000:00:02.1/usb1/1-1/1-1:1.0/host10/target10:0:0/10:0:0:0/bsg/10:0:0:0 (bsg)
UDEV [1264631867.538933] change /devices/pci0000:00/0000:00:02.1/usb1/1-1/1-1:1.0/host10/target10:0:0/10:0:0:0 (scsi)
KERNEL[1264631867.540308] add /devices/pci0000:00/0000:00:02.1/usb1/1-1/1-1:1.0/host10/target10:0:0/10:0:0:0/block/sdd (block)
KERNEL[1264631867.540365] add /devices/pci0000:00/0000:00:02.1/usb1/1-1/1-1:1.0/host10/target10:0:0/10:0:0:0/block/sdd/sdd1 (block)
KERNEL[1264631867.540578] add /devices/virtual/bdi/8:48 (bdi)
UDEV [1264631867.540589] add /devices/virtual/bdi/8:48 (bdi)
UDEV [1264631867.628087] add /devices/pci0000:00/0000:00:02.1/usb1/1-1/1-1:1.0/host10/target10:0:0/10:0:0:0/block/sdd (block)
UDEV [1264631867.668981] add /devices/pci0000:00/0000:00:02.1/usb1/1-1/1-1:1.0/host10/target10:0:0/10:0:0:0/block/sdd/sdd1 (block) -
I recently purchased my iPod touch with no issues. After updating to iOS 8.1.1 I found that my iPod would no longer appear in the latest version of iTunes and when I searched for Apple Mobile Device usb driver in the device manager, it was nowhere to be found. I've already uninstalled and re-installed ALL components of iTunes and read every single help article. I've tried everything. What went wrong?
See
iOS: Device not recognized in iTunes for Windows
- I would start with
Removing and Reinstalling iTunes, QuickTime, and other software components for Windows XP
or
Removing and reinstalling iTunes and other software components for Windows Vista, Windows 7, or Windows 8
However, after your remove the Apple software components also remove the iCloud Control Panel via Windows Programs and Features app in the Window Control Panel. Then reinstall all the Apple software components
- Then do the other actions of:
iOS: Device not recognized in iTunes for Windows
paying special attention to item #5
- New cable and different USB port
- Run this and see if the results help with determine the cause
iTunes for Windows: Device Sync Tests
Also see:
iPod not recognised by windows iTunes
Troubleshooting issues with iTunes for Windows updates
- Try on another computer to help determine if computer or iPod problem
Maybe you are looking for
-
Error while running batchdiagnostics.sh for AIA for Comms 2.0.1 installed
I read while going through a document that to check whether AIA installation was successful 1. User should run the $AIA_HOME/diagnostics/bin/batchdiagnostics.sh script. When completed the output can be reviewed in $AIA_HOME/diagnostics/logs/BatchDiag
-
Is there a downloadable PDF of the Flash (Or and other application) help files? If so where can I get them? Thank you, R.
-
Hi I have an Internal Order Settlement Error. Incident Details: P2P order No xxxxxxxxxx was booked into SAP in period 09 (lines 10 /20 & 30) This P2P Order was linked to an Internal Order (No xxxxxxxxx) and the cost was moved to the Asset Module when
-
Login password character limit?
Is there a limit to the number of characters you can use for a login password in OS X 10.4x? The Mac login screen can display 14 characters, but it seems that you can keep typing after 14 (you just can't see the additional characters). Thanks, Kevin
-
I've got a hp cp 1215. is that an eprinter ?????
i've got a hp cp 1215. is that an eprinter ?????