USB - Ethernet adapter

Anybody know if this adapter works on a Powebook G4 12'' 1.33Mhz with Tiger on it ?
EtherFast¨ 10/100 Compact USB Network Adapter
http://www.linksys.com/servlet/Satellite?childpagename=US%2FLayout&packedargs=c% 3DLProductC2%26cid%3D1115416833872&pagename=Linksys%2FCommon%2FVisitorWrapper
I blew up my Ethernet jack so need an alternative.
Thanks

No, it doesn't seem as though it does. I gathered this from the line of text below:
'The EtherFast® 10/100 Compact USB Network Adapter from Linksys allows you to instantly connect to a network from a USB-enabled desktop or notebook PC running any version of Windows that supports USB.'
You could contact LinkSys directly and see what they say.
Does your PowerBook have an in-built Airport Extreme card? If yes, you could purchase an Airport Extreme Base Station and use that as an alternative to connect to your network.
Stu

Similar Messages

  • USB Ethernet Adapter Stopped Working On Mac Mini Server Running 10.6.6

    Is anybody out there successfully using the Apple USB Ethernet adapter on a Mac Mini Server running 10.6.6? They have stopped working for me.
    The boot disk in the 2009 Mac Mini Server in my classroom failed and after Apple replaced the disk and I reinstalled SLS and ran Software Update to bring the machine up to 10.6.6 the USB Ethernet adapter that was the interface to the outside world no longer recognized when a cable was plugged in. The cable was good and worked just fine if plugged into another machine or the built-in interface. At first I thought that the USB Interface had failed but after trying two new ones (graciously exchanged by Apple) and finding that none of them worked I'm coming to the conclusion that perhaps the warning on the package that the USB Ethernet only works with the MacBook Air finally became true.

    Douglas Urner wrote:
    Is anybody out there successfully using the Apple USB Ethernet adapter on a Mac Mini Server running 10.6.6? They have stopped working for me.
    The boot disk in the 2009 Mac Mini Server in my classroom failed and after Apple replaced the disk and I reinstalled SLS and ran Software Update to bring the machine up to 10.6.6 the USB Ethernet adapter that was the interface to the outside world no longer recognized when a cable was plugged in. The cable was good and worked just fine if plugged into another machine or the built-in interface. At first I thought that the USB Interface had failed but after trying two new ones (graciously exchanged by Apple) and finding that none of them worked I'm coming to the conclusion that perhaps the warning on the package that the USB Ethernet only works with the MacBook Air finally became true.
    Only the specific build of Mac OS X that comes with a MacBook Air includes the kernel extension to run the Apple USB Ethernet adapter, however there are no hardware issues preventing it being used on other Mac models if you have a suitable driver.
    Generic USB drivers can be downloaded for free from http://www.sustworks.com/site/newsusbethernet.html and this worked for me.

  • Can't reach network video server on Mac Mini's USB Ethernet Adapter.

    I am trying to connect an IP video server to my Mac Mini's USB>Ethernet adapter. The server works fine on the built in Ethernet "en(0)", but is unreachable on the USB>Ethernet adapter network"en(3)".
    Is this a subnet issue? I don't know much about networking obviously, but I think I just need to find a way to designate the proper port to look on, because the Mac is looking on the built in Ethernet only when I specify http://192.168.0.90:80/
    The en(3) is configured for DCHP.
    I could just hook the server up to the built in Ethernet, but then I'll have to run new and very long cat 5 cable.
    I'd love to hear any ideas on how to get this working.

    The Network Settings for the USB>Ethernet port are:
    IPv4: Using DHCP
    IP Address 169.254.33.152
    Subnet Mask: 255.255.0.0
    Router: (none)
    DNS Server: (none)
    Search Domains: (none)

  • Does the Apple USB Ethernet Adapter work with a MacBook Air that's been updated to Lion?

    I saw a comment at the online Apple store that the USB Ethernet Adapter didn't work with Lion. Anyone else have experience with the adapter?

    Just point the tech rep to the apple website that lists the Ethernet to USB system requirements as:
    "Overview
    The Apple USB Ethernet Adapter is a simple, one-piece external adapter that plugs into the USB 2.0 port of your MacBook Air to provide 10/100BASE-T performance. Simply plug your Ethernet cable into the RJ-45 connector — no external power is required. It’s small, light, easy to install, and even easier to use.
    Technical Details
         USB 2.0 with bus power
         10/100BASE-T (RJ-45 connector)
    What's in the Box
         Apple USB Ethernet Adapter with built-in 4.6-inch USB cable
    User's Guide
    System Requirements
         MacBook Air computer with available USB 2.0 port"
    Note that there is no mention of a specific OS requirement.......Cut and pasted from apple.com.

  • MacAir - Apple USB Ethernet Adapter Drive

    Hi,
    im using macair, and trying to install bootcamp for windows Vista / XP. however, im having difficulties to download driver for Apple USB Ethernet Adapter. if anyone know where to download this driver, please advise me..

    Welcome to Apple Discussions!
    There doesn't seem to be a clear-cut answer to this. If you read the reviews on the Apple site, some people have been able to make the ethernet adaptor work on some PowerPC Macs, and others can't even get it to work on a different Intel Mac. I know this isn't much help, but a perusal of these reviews might be the best resource unless someone else has actually done this with the same iBook that you have.
    I assume you have tried a different ethernet cable?
    Good luck!

  • Apple USB Ethernet Adapter and VLAN??

    Bought the Apple USB Ethernet Adapter today because my built in ethernetport on my MBP stopped working. What I know I need to replace the motherboard to have it fixed, so I thought the USB adapter could be useful until then.
    But, it didn't work! I only got a "Self assigned ip-address". No matter what I do. I also entered an ip-address manually with no success.
    Later at home I tested again, and Voila!! It worked perfectly!
    Back at the office, same problem... I only get a "Self assigned ip-address"...
    My conclusion of this is that the Apple USB Ethernet Adapter doesn't support VLAN?? Could anyone confirm that or better of, suggest a solution??
    Would appreciate it a lot!
    PS. Yes we do have Wi-Fi, but it's restricted and is not a solution for me. DS.

    Create a new network location and try again.
    https://discussions.apple.com/thread/2624518?threadID=2624518&tstart=45

  • Will Apple's USB-Ethernet Adapter Work on iMac

    One of the pins in the ethernet port of my iMac were bent. The second I attempted to bring the pin up, it broke. So I haven't been able to use ethernet for over a year.
    Will the Apple USB Ethernet Adapter work on my Late 2006 2Ghz Intel Core 2 Duo iMac? It is loaded with Leopard 10.5.5. I've read these adapters would only work for MBAir but will it work on my iMac?
    I'm not looking to get back Gigabyte Ethernet capability, I generally want to use ethernet again.

    I do have a Base Station the current base station.
    All my stuff except my iMac & iBook is packed deep in a storage facility since I'm on a move to someplace else. Meanwhile I'm staying in a place that doesn't have Wi-FI but offers wired ethernet connection.
    I have my iBook but I want to use my iMac again & that adapter is all I need to get it connected. I just want to know if it would work since it's intent is for the MacBook Air.

  • Can you determine link status with USB Ethernet adapter?

    I'm wanting to replace an old G4 PowerBook with a 11" MacBookAir. I install networks, and I often need to determine link status of an Ethernet connection. With the built-in Ethernet port on most Macs, you can check the Network Status to see if there is link on an Ethernet connection (either the green or yellow status signs).
    If I am using the Apple USB Ethernet adapter, do I get similar feedback from the Network preference panel? If not, perhaps a terminal command that would do the same?

    Yes - the Network Panel under System Preferences works the same as with a regular Mac, showing USB Ethernet status (connected, disconnected, etc) and with the updated connected IP address, etc.

  • After i updated to mavericks, my usb ethernet adapter stopped working.

    I'm not sure why, but when I updated my software to mavericks, my USB ethernet adapter stopped working.

    I'm using that adapter:
    http://www.edimax.com/en/support_detail.php?pd_id=445&pl1_id=5&pl2_id=26
    After I updated to Mavericks, I installed the driver in this page, but it didn't work. Then I googled "AX88772" which is my adapter's part no. or something like that, and I installed that one:
    http://www.asix.com.tw/download.php?sub=driverdetail&PItemID=97
    I wasn't expecting that work but that did work. So, I think the solution of the problem is finding the right driver. I hope you solve your problem too.

  • I get the following error message when I connect a usb ethernet adapter to my new MacBook Pro: Unsupported - You cannot use an Apple USB Modem with this computer. I live were we only have dial-up and the Apple Store said this is what I need.

    I get the following error message when I connect a usb ethernet adapter to my new MacBook Pro: Unsupported - You cannot use an Apple USB Modem with this computer. I live where we only have dial-up and the Apple Store said this is what I need. In addition, when I connect the phone to the connecter it falls out, it will not click in.

    Why are you using a usb ethernet adaptor? Just plug the modem into the usb port.

  • MBAM Client moves to Recovery mode on removing USB Ethernet Adapter.

    We have deployed MBAM 2.5 Stand Alone topology in one of my Customer environment. All the laptops in my customer environment doesn't have Ethernet port and they are using USB Ethernet adapter to connect the Ethernet cables. On the encrypted laptops, when
    a user BOOT a machine without having this USB Ethernet adapter connected to laptop, machine is forced to recovery mode each and every time the machine BOOTS up. 
    Appreciate any help to get this fixed.
    Thanks
    Jegath Rakshagan

    Take a look at Scenario 1 in
    Issues Resulting in Bitlocker Recovery Mode and Their Resolution on the Ask the Core Team blog. The issue may be occurring due to a change in the boot priority when the ethernet adapter is removed, try setting the HDD to the first boot device.
    Brandon
    MDOP for IT Professionals on TechNet

  • I cant not get my USB ethernet adapter to work with my new Macbook Air.

    So this is the second adapter I have bought and it seems to not work still. I didnt check System info on the first adapter but on the second one i noticed this. The current required mA is unknown.  Is there a fix for this or should I try and get another adapter. I have the 2011 MacBook Air running lion.
    Apple USB Ethernet Adapter:
      Product ID:          0x1402
      Vendor ID:          0x05ac  (Apple Inc.)
      Version:          0.01
      Serial Number:          15069A
      Speed:          Up to 480 Mb/sec
      Manufacturer:          Apple Inc.     
      Location ID:          0xfd120000 / 4
      Current Available (mA):          500
      Current Required (mA):          Unknown (Device has not been configured)

    Check System Preferences > Network > verify the Ethernet service is defined.   If not, click the "+" icon below the services list and add it.
    Regards,
    Captfred

  • Usb ethernet adapter, create network

    I'm trying to use the usb ethernet adapter to create a network notebook wi-fi.  I've had major headaches getting usb ethernet adapter to work, but when it is working and I try to create a network, problems reoccur with the adapter.  Can I expect to create a network while using the apple usb ethernet adapter?

    Did it do this on 10.7.3? We have this: plugging in a USB card reader drops the USB ethernet. It does it on 10.7.4, 10.7.5, 10.8.2 and 10.8.3 but not 10.7.3 ?!?

  • Can't get my mail when use the USB Ethernet adapter

    I can't get my mail when use the Apple USB Ethernet Adapter. If I use a wireless connection, there is no problem. The LAN which I'm trying to connect is behind a proxy server but the Internet is working 100%.

    Hi ViK,
    This sounds like a question for the network administrator of the location. Without knowing how the proxy is set it's impossible to know what it's blocking (incoming/outgoing). It sounds like it might be filtering the incoming mail server.

  • Hp usb ethernet adapter

    Does anyone know what chipset is in the hp usb ethernet adapter MFG# XZ613AA#ABA?
    OR, where I can find a usb ethernet adapter with an intel chipset?
    Any help greatly appreciated! I have a Twincat x64 program that only supports intel NICs, and it only works sporadicaly in virtual mode.
    Oh yea, HP 630 notebook, Windows 7, Realtek ethernet adapter.
    Thanks again!

    If the adapter works with the printer, and you can get a recent and proper
    driver from the HP support or downloads page, it should be able to print.
    And there may be alternative drivers from gimp-print open source.
    There also are powered ethernet hubs you can get, so all things ethernet
    can be run from the main port on the computer and not be underpowered.
    In fact, I have one in a box I don't use just yet because I can run my Epson
    printer via USB over my AirPort Express (or AirPort Extreme) base station
    and then the other printer, an all-in-one HP OfficeJet something, can run by
    wire; since it won't work as a Bonjour printer and isn't seen as an option.
    Some are supported and others may be conditionally able to work in these
    different situations; so you may have to change your plans if a powered
    Ethernet bridge, or whatever, becomes a second option; or other ideas fail.
    The options include using the printer as USB, ethernet, or wireless; and
    the latter may include the need to choose a compatible wireless bridge
    or a wired Ethernet powered hub. And then seeing if you can get the
    printer setup to see the printer when configured in whatever selection
    or setup you've chosen to use can be equally ufn (unfun.)
    If I wanted to run the HP I have by ethernet, it could do it; but you have to
    note these things get an ID like the internet, sort of, if you use Ethernet.
    Some adapters work and others may not; so it could be a hit & miss trial.
    And some say there are advantages to the Ethernet if used on a network.
    Good luck & happy computing!

  • Can I use any USB-Ethernet adapter, or do I need to buy the Apple part?

    I'm about to get an Air and do the migration from my old PowerBook.  Can I use the Netgear USB-Ethernet adapter for the Air, or do I need to buy a new Apple part?

    Little update for the usb to ethernet adapter is in order. Both adapters are producing Gigabit ethernet max. Keep in mind that new macbook air has the usb 3 version ports at 5 Gigabit internal speed where Thunderbolt has 10 Gigabit per chanel internal capacity. In ether case more than suficient to provide Gigabit ethernet output. Nither one will push more than that out to the ethernet. In my case the decission was made by availability. I wanted the thunderbolt adapter for the sake of keeping up with the technology but there was none on the shelf.
    Just my two cents
    Zoran

Maybe you are looking for