USB Ethernet port not working after ML install

After installing ML I cannot get the USB Ethernet port to work. Have searched for andriod file transfer agent but cannot locate it as previously mentioned.

Same Problem over here. Has anyone a good idea how to fix this problem?
After installing ML i cannot get my original Apple USB Ethernet port to work (Macbook Air 2011).

Similar Messages

  • Usb ports not working after mavericks install

    After installing Mavericks on my mac pro the usb ports are not working for my printer or other usb drives. the only item i can get to be seen via usb is an apple optical mouse. any suggestions would be great.

    Hi there grnded189,
    You may find the troubleshooting steps in the article below helpful.
    OS X Mavericks: If a USB device isn’t working
    http://support.apple.com/kb/PH13876
    You may also want to reset the PRAM and SMC as well.
    OS X Mavericks: Reset your computer’s PRAM
    http://support.apple.com/kb/ph14222
    Intel-based Macs: Resetting the System Management Controller (SMC)
    http://support.apple.com/kb/ht3964
    -Griff W. 

  • Ethernet Port Not Working After 10.6.6 Upgrade

    Hello! Since upgrading to 10.6.6, I have lost my Ethernet port connectivity. AirPort is working fine.
    I have done the following:
    -checked ethernet cable
    -used System Preferences/Network to check connection and try to create a new one
    -used Diagnostic button
    -zapped PRAM
    -reset SMC
    -repaired my disk permissions
    -installed the 10.6.6 combo update
    -booted in Safe Mode and then restarting
    Is anyone aware of an incompatibility with 10.6.6 and the Yukon adapter?
    Any suggestions greatly appreciated!
    Marvell Yukon Gigabit Adapter 88E8053 Singleport Copper SA:
    Name: ethernet
    Type: Ethernet Controller
    Bus: PCI
    Vendor ID: 0x11ab
    Device ID: 0x4362
    Subsystem Vendor ID: 0x11ab
    Subsystem ID: 0x5321
    Revision ID: 0x0022
    Link Width: x1
    BSD name: en0
    Kext name: AppleYukon2.kext
    Location: /System/Library/Extensions/IONetworkingFamily.kext/Contents/PlugIns/AppleYukon2 .kext
    Version: 3.2.1b1
    Hardware Overview:
    Model Name: MacBook
    Model Identifier: MacBook1,1
    Processor Name: Intel Core Duo
    Processor Speed: 2 GHz
    Number Of Processors: 1
    Total Number Of Cores: 2
    L2 Cache: 2 MB
    Memory: 1 GB
    Bus Speed: 667 MHz
    Boot ROM Version: MB11.0061.B03
    SMC Version (system): 1.4f12
    Message was edited by: bhughes2172

    let me reiterate. 27 ' iMac 3.06 GHz Intel Core 2 Duo just updated to 10.6.6 uses AirPort to access the internet. Set up to share it's internet connection via ethernet with PPC Dual 2.3 G5 running 10.5.8. Up until the 10.6.6 update things were fine. After updating the iMac's OS, the PPC lost it's internet connection. On the PPC's network System Prefs, the built in ethernet is connected and green. The iMac is in the finder under Shared. On the iMac, the PPC is in the finder under Shared and in Network settings the ethernet connection has a self-assigned IP with a yellow light. I have reset and rebooted all settings and devises on the network with no resolve.

  • USB Ethernet is not working after upgrade to 10.8

    Hi,
    I am not getting connected to the LAN with my USB ethernet. Anyone with similar situations? Don't tell me to convert to thunderbolt please.

    you dont have wifi?

  • Ethernet port not working after installing Leopard

    All fine when in 10.4.8, after installing 10.5 it no longer works.
    Says cable is unplugged, checked the cable on other devices and the router and cant see any problems on system profiler.
    Any ideas ?

    Cat6 cables are not required or beneficial for most home situations. The purpose of Cat 6 cables is to be able to work around a electronically "noisy" area, or to pinch out a little bit more throughput in a Gigabit network.
    If you change a cable to Cat6 it will still work at the Cat5 or 5e standard if any of your other cables are not Cat6.
    I'm running GB ethernet using hundreds of feet of Cat5e wiring into several rooms. No problems with Leopard.

  • HP G4-2275dx left two usb ports not working after OS install.

    Hi all.
    I had to remove my windows 8(Upgraded to Pro before) install due to compatibility with certain programs and I was not very satisfied with the results.
    So I had an extra cd key for windows 7 x64 home premium.
    Everything went smooth.
    I had all my drivers installed.
    I installed Direct X also.
    But when I tried to use my tutle beach headset it would not install the driver for the headset or even make the sound when a device is mounted.
    So I checked device manager and I saw three yellow excelemation errors.
    two were "Universal Serial Bus(USB) controller"
    one was "SM bus controller"
    I have installed the catalyst drivers multiple times but no dice.
    Any help will be appreciated.
    Happy Holidays.
    This question was solved.
    View Solution.

    Hi,
    Download and install the Chipset driver from the following link.
    http://support.amd.com/en-us/download/chipset?os=Windows%207
    When done, restart the notebook.
    Regards,
    DP-K
    ****Click the White thumb to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    ****I don't work for HP****
    Microsoft MVP - Windows Experience

  • Hp 15-D018TU USB SS PORT NOT WORKS

    Hi, In my HP 15-d018tu Notebook PC the USB SS port not works.Can anyone look into this problem and guide me.
    Thanks in Advance

    Hi:
    Did you install the applicable usb3 driver?
    http://h20564.www2.hp.com/hpsc/swd/public/detail?swItemId=ob_135422_1

  • Flash player does not work after I installed it

    Flash player does not work after I installed it

    I'm using Mac Osx and my browser is Safari
    Date: Wed, 5 Feb 2014 00:41:29 -0800
    From: [email protected]
    To: [email protected]
    Subject: Flash player does not work after I installed
        Re: Flash player does not work after I installed it
        created by Mike M in Installing Flash Player - View the full discussion
    This is a user-to-user forum, NOT 24/7 support. You're "lucky" I happen to be up at 1:40 am to answer you.
    What OS are you using?
    http://mmonlinedesigns.com/images/os.png
    What browser?
    http://mmonlinedesigns.com/images/browsers.png
         Please note that the Adobe Forums do not accept email attachments. If you want to embed a screen image in your message please visit the thread in the forum to embed the image at http://forums.adobe.com/message/6087541#6087541
         Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page: http://forums.adobe.com/message/6087541#6087541
         To unsubscribe from this thread, please visit the message page at http://forums.adobe.com/message/6087541#6087541. In the Actions box on the right, click the Stop Email Notifications link.
               Start a new discussion in Installing Flash Player at Adobe Community
      For more information about maintaining your forum email notifications please go to http://forums.adobe.com/thread/416458?tstart=0.

  • My printers are not working after mavericks install. What can I do to fix - PLEASE HELP! It is my lifeline - we are a print shop!

    My printers are not working after mavericks install.
    The printer just PAUSE and can't be resumed.
    What can I do to fix - PLEASE HELP!
    It is my lifeline - we are a print shop!

    Go to the printer manufacture website and download the drivers for your printer model for OS X v10.9 Mavericks.
    Then open System Preferences > Printers & Scanners > Print
    Select your printer on the left then click -  (minus)
    Then click + (plus) to add the printer.

  • Security and privacy system preferences not working after Lion install.  What to do?

    Security and privacy system preference not working after Lion install.  Not sure if it happen with Lion installer or after updating. What to do?

    Please read this whole message before doing anything.
    This procedure is a diagnostic test. It won’t solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
    Third-party system modifications are a common cause of usability problems. By a “system modification,” I mean software that affects the operation of other software — potentially for the worse. The following procedure will help identify which such modifications you've installed. Don’t be alarmed by the complexity of these instructions — they’re easy to carry out and won’t change anything on your Mac.
    These steps are to be taken while booted in “normal” mode, not in safe mode. If you’re now running in safe mode, reboot as usual before continuing.
    Below are instructions to enter some UNIX shell commands. The commands are harmless, but they must be entered exactly as given in order to work. If you have doubts about the safety of the procedure suggested here, search this site for other discussions in which it’s been followed without any report of ill effects.
    Some of the commands will line-wrap or scroll in your browser, but each one is really just a single line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, and you can then either copy or drag it. The headings “Step 1” and so on are not part of the commands.
    Note: If you have more than one user account, Step 2 must be taken as an administrator. Ordinarily that would be the user created automatically when you booted the system for the first time. The other steps should be taken as the user who has the problem, if different. Most personal Macs have only one user, and in that case this paragraph doesn’t apply.
    Launch the Terminal application in any of the following ways:
    ☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
    ☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
    ☞ If you’re running Mac OS X 10.7 or later, open LaunchPad. Click Utilities, then Terminal in the page that opens.
    When you launch Terminal, a text window will open with a line already in it, ending either in a dollar sign (“$”) or a percent sign (“%”). If you get the percent sign, enter “sh” (without the quotes) and press return. You should then get a new line ending in a dollar sign.
    Step 1
    Copy or drag — do not type — the line below into the Terminal window, then press return:
    kextstat -kl | awk '!/com\.apple/{printf "%s %s\n", $6, $7}'
    Post the lines of output (if any) that appear below what you just entered (the text, please, not a screenshot.) You can omit the final line ending in “$”.
    Step 2
    Repeat with this line:
    sudo launchctl list | sed 1d | awk '!/0x|com\.(apple|openssh|vix)|edu\.mit|org\.(amavis|apache|cups|isc|ntp|postfix|x)/{print $3}'
    This time, you'll be prompted for your login password, which won't be displayed when you type it. You may get a one-time warning not to screw up. You don't need to post the warning.
    Note: If you don’t have a login password, you’ll need to set one before taking this step. If that’s not possible, skip to the next step.
    Step 3
    launchctl list | sed 1d | awk '!/0x|com\.apple|edu\.mit|org\.(x|openbsd)/{print $3}'
    Step 4
    ls -1A /e*/mach* {,/}L*/{Ad,Compon,Ex,Fram,In,Keyb,La,Mail/Bu,P*P,Priv,Qu,Scripti,Servi,Spo,Sta}* L*/Fonts 2> /dev/null
    Important: If you synchronize with a MobileMe account, your me.com email address may appear in the output of the above command. If so, anonymize it before posting.
    Step 5
    osascript -e 'tell application "System Events" to get name of every login item' 2> /dev/null
    Remember, steps 1-5 are all drag-and-drop or copy-and-paste, whichever you prefer — no typing, except your password. Also remember to post the output.
    You can then quit Terminal.

  • IMessage not working after IOS7 install?

    iMessage not working after IOS7 install?

    Yep, it has issues. Word is that Apple is working on an update to fix it but no idea when it'll be rolled out.

  • USB ethernet does not work in left USB port

    My USB ethernet adapter does not work in the left USB port on my MacBook Air, but it works in the right side. Other devices, like my mouse, work fine in both ports.
    Could I have a faulty left-side port with too little power for the ethernet adapter, or is this normal for MacBook Air?

    I have the same problem.
    USB Ethernet doesn't work with the left USB port. It does work with the right USB port, and any other USB device works with the left USB port on my macbook air
    Any solution to this problem?

  • Windows 8.1 64-bit USB 3 ports not working

    I have a T430s computer model 2352CTO, running Windows 8.1, 64-bit version. Prior to upgrade from Windows 8.0 all drivers were updated. The USB 3 ports worked correctly, in particular running an external 1gb hard drive. After update to 8.1, the USB 3 ports still work, but only for about 30 seconds then the hard drive shuts down. The power light is still lit on the hard drive, but it no longer shows in windows explorer.
    In device manager, I went to Universal Serial Bus Controllers -> USB Root Hub ->Properties->(under General it says "This device is working properly)->Power Management->Unchecked the box for "Allow the computer to turn off this device to save power". Unfortunately this does not seem to stop problem. Any ideas?
    Solved!
    Go to Solution.

    Please try this:
    http://blogs.msdn.com/b/usbcoreblog/archive/2013/11/01/help-after-installing-windows-8-1-my-usb-driv...
    Thanks!
    Houman

  • HDMI Port not working after Windows 10 Upgrade

    My HDMI port quit working after upgrading to Windows 10. The VGA port works fine. I have triend many of the fixes for listed for this issue for upgrading from Windows 7 to Windows 8/8.1. Here's whay I've done so far... 1) Downloaded the most recent drivers for my Intel(R) Graphics Card. Outcome: It said the drivers installed were newer than the driver I was installing. Tried anyway, didn't work. 2) Uninstalled the driver and let windows update it.Outcome: Black screen, then it restarted and installed the same driver it had before. 3) Tried installing the Windows 7 Driver for my Intel(R) Graphics Card. Outcome: Black screen, then it restarted and installed the same driver it had before. 4) At this point I tried the last resort. I spun around three times in a circle and spit in the corner.Outcome: Wife yelled at me and kids thought I had a demon.  Please help, I use this computer in the office to connect to a 65" TV and I NEED my HDMI port. 

    Yeah, lot's of people on this forum have stated they have the same issue. It's not just people with Intel/AMD switchable cards either. I have an AMD 8650G + 8670M dual grapgics card and I am having the same issue. 

  • Mountain Lion Mac Mini Server Ethernet Port Not Working

    I have a Mac Mini Server and once I upgraded to Mountain Lion Server the Ethernet port is unresponsive. It worked before upgrading. Is there something with Mountain Lion Server that is causing the Ethernet port not to work properly?

    Make a "Genius" appointment at an Apple Store.
    Back up all data on the internal drive(s) before you hand over your computer to anyone. If privacy is a concern, erase the data partition(s) with the option to write zeros* (do this only if you have at least two complete, independent backups, and you know how to restore to an empty drive from any of them.) Don’t erase the recovery partition, if present.
    Keeping your confidential data secure during hardware repair
    *An SSD doesn't need to be zeroed.

Maybe you are looking for