USB external portable HD for use with FCE and MBP ???????

I've seen a 120 GB USB portable external Seagate HD for $117. Would this be usable as a scratch disk for use with my MBP 2.0 and final cut express HD 3.5. Are there problems with using USB externals? FW external hd's seem to be a good deal more expensive.
Thanks.
Maurice

I bought one recently very cheaply to use for general storage.
I found that FCE 3.0 worked perfectly and have been using it ever since instead of my FW HD.
HOWEVER, before you dash out and buy one take note that I have only been tinkering around and experimenting with comparatively short projects of no importance.
I strongly suspect that if I made a long and complicated film I might suffer - so pay the extra and get a FW HD !
Incidentally for normal storage purposes the USB2 HD takes over twice the time to move files back and forth. So even for non-FCE use the Firewire HD is twice as fast.
Ian.

Similar Messages

  • I'm sorry, I have to convert the mov file. for use with fce and / or imovie11, better ProRes422 or intermediate codec?

    I'm sorry, I have to convert the mov file. for use with fce and / or imovie11, better ProRes422 or intermediate codec?

    FCE only used AIC for HD.
    Al

  • Can someone suggest an affordable external hard drive for use with FCPX and video editing on my Macbook Pro Retina

    I have a Macbook Pro Retina from 2012 and I only got the 250GB hard drive.  I'm getting ready to purchase a Panosonic HC-X920 to use with Final Cut Pro X already installed on my laptop.  Since I know the file sizes are going to be so big, can anyone suggest an affordable external drive fast enough to keep up with editing the video?  I'm not a pro and use it for family and personal projects. 
    I prefer some thunderbolt options since I haven't had a chance to use the inputs since I got my macbook pro. I just don't know what is necessarily too little or too big and too cheap and too expensive for my needs.  Thank you.  

    OWC is a Mac specialist and a very trustworthy vendor.  I have dealt with them and their technical stall on many occasions.  Hence you may look at what they offer and be assured that they will stand behind what they sell:
    http://eshop.macsales.com/shop/Thunderbolt/
    I suspect that for your needs, a 1 TB drive is going to be the minimum.
    Ciao.

  • Recommend an External Floppy Drive for use with G5 and Leopard?

    I need to pull some data off a number of floppy disks I used with my old Mac. Can anyone recommend a brand and/or source. Speed is unimportant. Can use USB.

    Any USB floppy will work. Apple store sells Smartdisk.

  • What is a good external hard drive for use with a macbook air?

    I am looking at purchasing a macbook air 13". What is a good external hard drive to use with it? Should I look for an external hard drive with its own a/c power or is the usb 3.0 capable of powering the external drive.

    Have a look here for the sizes and prices.
    It is however, much better to get a USB external drive that comes with it's own power adapter to avoid issues when or if your USB port can't supply enough power to your external drive.
    That issue however does happen rarely but it does happen.  Especially when connecting other devices to your other USB port while your external hard drive is connected to your other usb port.

  • Partitioning an External 320gb drive for use with Time Machine and...

    I want to be able to use my Western Digital 320GB external drive for use with Time Machine and to use as extra storage space on both my Mac and when I boot into Windows Vista.
    Is this possible?
    I was playing around in Disk Utility and would I partition the part I want to use for Time Machine with the Mac OS Journaled, and whatever I want as space for windows, use a MS - DOS format?
    Has anyone done this before?
    Cheers-

    Unless you are using 64 bit version of MSWindows (64 bit XP/Vista), it won't be able to handle a disk with GUID partition table (GPT). Disks with Apple Partition Map (APM) or GUID partition table are the only ones that Time Machine will work with (not MBR disks). Note also that the MBR/APM/GPT are at the DISK level and not the partition level, so don't mix the format with partitioning scheme. Time Machine disks are meant to live in the Mac universe (for now, anyway) and sharing with the MSWindows 32-bit universe is not possible.
    See http://img87.imageshack.us/my.php?image=macpcdiskdd06sv8.png for some additional background.

  • External Touch Screen for use with x220 running Tablet PC for XP

    I've been tasked to purchase an external touch monitor for use the the x220 running Tablet PC for XP but the monitor specs typically show "Windows Vista/Win7" supported. Will any touch monitor correctly work with this OS? Any recommendations?

    Hello,
    I would imagine you would need to find a touch-enabled screen that has device drivers for Microsoft Windows XP available for it.
    Regards,
    Aryeh Goretsky
    I am a volunteer and neither a Lenovo nor a Microsoft employee. • Dexter is a good dog • Dexter je dobrý pes
    S230u (3347-4HU) • X220 (4286-CTO) • W510 (4318-CTO) • W530 (2441-4R3) • X100e (3508-CTO) • X120e (0596-CTO) • T61p (6459-CTO) • T43p (2678-H7U) • T42 (2378-R4U) • T23 (2648-LU7)
      Deutsche Community   Comunidad en Español Русскоязычное Сообщество

  • Switching to AT&T Cingular - best phone for use with Mac and iSync

    Dear Friends,
    I am finally about to be free from Sprint's poor customer service. I will be switching to AT&T / Cingular. (Not quite ready to buy an iPhone, but don't want to be locked into a 2 year contract with another provider).
    I want to use Apple's iSync. I have reviewed the list of compatible devices and scanned the forums for related topics.
    I'm still left wondering:
    What is the best phone to get with AT&T for use with iSync?
    I would like to sync contacts both ways. If possible, syncing cal events and to-dos would be nice, but not as important as contacts.
    I prefer small flip phones. I don't plan to buy the Media pack service that includes text, web, etc. Instead, I will use the phone for calls and occassional text messages.
    Sound quality and the ease of use are the most important features for me. I prefer raised keys to the flat keypads, but could give on this if need be.
    Finally, using the phone as a modem with my laptop would be nice, but is not essential.
    Thanks so much for any help you can offer.
    David

    I am facing the exact same question regarding, e.g., the Nokia 6126. There are several references:
    1. Go to the Nova Media web site and look at their new product, Fone Link. Or their iSynch Plugins
    2. One of the forum threads references, http://www.macosxhints.com/article.php?story=20060915154526806
    3. Another link I found http://soapbox.co.nz/past/2007/4/9/nokia-6126-and-isync-revisited/
    But what I don't yet understand is whether or not any of these suggestions/solutions are affected by the carrier. My understanding is that the 6126 is the North America Version of the 6131. But I talked to ATT/Cingular support yesterday and they make some modifications to the phone software. They don't know if the ATT 6126 will synch with a Mac. Of course they know the answer if synching with a PC (!!)

  • Min max lot size time based for use with SNP and PPDS

    Hi all, Is there anyway to set up time based min and max lot sizes? ie we want to have a Max lot size which is small for use with the first 3 months of our plan which starts life in SNP and then converts to PPDS and into blocks for block planning, but months 4 to 36 we want to leave as large max lot sizes as there is no need to have the small max lot sizes for the different horizon.
    As far as I can see there is only a material/plant lot size  and Max lot size and no way to have a different setting in a different time period.
    Thanks
    j

    Hi John,
    As you know, in the product master, the lot size maintenance is time-independent, so that obviously can not be used for your scenario. As per my understanding, to meet this using standard functionality, you can maintain multiple product specific t-lanes (for STRs) and PDSs (planned orders) with required lot size ranges and validity dates (for short or long term horizon). But, again since the validity of t-lanes and PDSs will not be automatically rolling forward so the updating the validities will be a challenge.
    The other option could be to enhance the heuristic functionality at lot size selection step while creating order.
    Regards,
    Umesh

  • HT3529 How can I get dictation for my iPad for use with email and messaging

    How can I get dictation to use with messaging and email?

    Apple's dictation requires Siri, which requires a 3rd or 4th generation iPad (or iPad Mini).  See:
    http://support.apple.com/kb/HT5457
    Your post says you have a second generation iPad, so it will not have dictation.
    There are third party apps available that might help you.

  • Quiet external hard drive for use with Time Machine?

    Few questions related to Time Machine:
    1- what external hard drive that would be good to use with Time Machine, that also runs relatively quietly? Since TM runs 24/7, am looking for one that is quieter than my current G-tech.
    2- Please confirm what size is optimal relative to the size of the internal hard drive.
    3- I currently use a separate external hard drive as my bootable disc.  Is it possible/preferable to have these be on one and the same drive?
    Thank you.

    1. I like these (have three of them) - literally whisper quiet:
    http://eshop.macsales.com/shop/firewire/1394/USB/EliteAL/eSATA_FW800_FW400_USB
    2. You should allow 2 - 3 times your internal drive's size for TM.
    3. No, it'd be best to be on another drive - you can create separate partitions, but if/when the drive fails, both of your backups would be gone. So, keep your clone on a separate disk. In fact, it's good to have two different backups.

  • Is there a preferred Video Camera in the forum for use with FCE?

    I am on the hunt for a new HD camcorder in the 800 to 1200 US dollar range. Is there a preferred recording format or anything specific to look for that will help my camera work best with FCE or better yet are there things I should try to avoid?
    I am looking for something compact so that I can carry it with me on trips easily, but still give a good quality HD image. Thanks

    The main consideration is that AVCHD is a hard drive based format whereas HDV is tape based. The nature of tapes is that they're relatively inexpensive so it's not such a big deal to save your tapes as backups in case you ever need to restore your project from the original footage. For AVCHD on the other hand, you'd need to make a backup by copying the whole file directory to an external drive for safe keeping, and if the drive fails or gets corrupted then you are out of luck.
    There are other less important things to keep in mind. AVCHD can reach a maximum resolution of 1920x1080, whereas HDV by comparison reaches its peak at 1440x1080. I've heard some say that AVCHD cameras generally work less well in low lighting conditions, but I personally haven't noticed too much of a difference. Finally, the market seems to generally be moving away from a tape based workflow. Not that AVCHD is exactly the format of the future (and you'll certainly be able to purchase DV tapes for a while to come), but it's something to keep in mind. FCE deals with the two formats differently as well, and it might be wise to skim over both the section in the User Manual about capturing and the one about the "Log and Transfer" process.
    As far as bugginess is concerned, I wouldn't say that one format is prone to more problems than the other. As long as you read up on the capture or ingest process before attempting anything you should be fine.
    Finally, keep in mind the fact that FCE transcodes both HDV and AVCHD into the Apple Intermediate Codec upon capture or ingest. AIC usually runs at about 41-50GB per hour, so you'll want to make sure that you have a fast external firewire drive to use as a scratch disk when editing to store your media.
    Sasha

  • Format external hard drive for use with macbook pro

    I have an old external drive that has been used with a pc.
    Now I have formatted the disc on the pc, but seemingly, I need to format it for the MacBook Pro, as well.
    How to?
    Rgds Jan

    Go to disk utility
    Format it in Mac OSX extended journaled
    Warning-- doing so will erase all data on the drive

  • External hard disk for use with quicksilver 2002 and intel imac 24"

    i am wanting to purchase an external hard disk to be used with both a g4 and an intel imac 24".
    i am considering a seagate barracuda 500gb or 750gb and purchasing an external case separately.
    interfaces - usb2, firewire 400 and 800.
    Do I need a case with the "oxford chipset" to have it work.
    Are all seagates compatible these days.
    I was looking at a ultra ata100 hard disk. Will this disk connect automatically to the enclosure or will additional cables be required
    Is the Ice Cube Generation II Ide enclosure ok to use.
    Appreciate any help given
    dual 1 gig G4, Intel 24" Imac   Mac OS X (10.4.8)  

    Hi-
    The Ice Cube uses an Oxford chipset, (part of the external housings onboard controller) so it should be fine. The Oxford chipset has been shown to give the best compatibility and performance, thus being an desirable feature.
    http://www.pccasegear.com/prod2307.htm
    Using a Seagate Ultra ATA 100 drive should give you good, quiet, reliable service. There are no problems with the Seagate ATA drives.
    Using the drive and housing with firewire will give you the best results, and firewire will allow you to use a bootable backup on the external drive, should the need be.
    The housing comes with all the necessary cables to connect and use your external drive.
    Insert the hard drive into the housing, connect the power and the firewire, format the hard drive, and you are ready to go..........
    G4AGP(450)Sawtooth, 2ghz PowerLogix, 2gbRAM, 300gbSATA+160gb HD, ATI Radeon 9800   Mac OS X (10.4.8)   Pioneer DVR-109, LaCie 160gb, 23"Cinema Display, Ratoc USB2.0, Nikon Coolscan

  • NAT / cant select my external Ethernet Card (for use with PPPoE)

    Hi i'm experiencing difficultys in setting up my server with a public IP adress on my external ethernetcard through PPPoe (xDSL). This setting is described as a sample setup in "ServerAdministrationv10.5.pdf" The following problems com up:
    - When i try to settup trough Server Assistant and i come to Network settings both (external (WAN)& internal (LAN)) Ethernetcards show up. As an necessery information there is asked for "PPPoE Servicename" (besides accountname and password). My ISP doesnt require a PPPoE Service name and when i query (?) what is asked for Server Assistant tells me that except i get the information from my ISP i have to leave the field blank. Now, i cant continue with the setup when leaving the field blank . The information is required. When i just supply some information and continue with setup the setup ends with a long pause and an errormessage.
    - Second try, after initial clean installation i Setup the server again localy with the default Serverassistant. When asked to post IP-Adress and Subnetmask for the first listed Ethernetcard i just leafe it with DHCP and continue. After initial Setup is complete i try to reconfigure the external (WAN) Ethernetcard with PPPoE. By doing that(in Systemettings / Networksettings) a get something like a new virtual Interface on my External EthernetCard. I enter the necessary information (accountname, password and leave the field for "PPPoE Servicename" blank. I connect to my ISP and get a perfect connection. No problem to brouse the Web or make FTP connection.
    Now when i continue to finish the setup of my new leopard-server i'm asked to select the external Ethernetcardin NAT. Unfortunally i have know three Ethernetinterfaces (External with DHCP, External with PPPoE and the internal one for my LAN). The 2 externel EthernetInterfeces have both the same Name (in NAT)
    and somehow i cant select the one where i have setup my PPPoE.
    Now, i go back to Networksettings and delete the initial Externalcardsetting (leaving with only my working PPPoE setting on the External Ethernetinterface). As the result of this manipulation i cant select the external Ethernetinterface in NAT anymore. Only the internal (LAN) Ethernetinterface shows up.
    Can anybody help me with to above discribed Problem? Somehow i have to be able to select my working PPPoE Setting (on my external Ethernetinterface) in NAT.

    I have this exact problem on my new Intel Xserve. During setup I configure ethernet 1 with a manual IP address and try to set up ethernet 2 for PPPoE (it will connect to my ISP via the ADSL modem/bridge) but despite the help screen saying do NOT type anything in PPPoE Service Name unless requested to do so by the ISP (they don't), if I leave it blank it complains because that field is empty and returns to the same screen.
    This brings the entire installation to a halt. Seems to me like it's a big bug - I cannot see any way around it. Someone please tell me I'm being stupid here and the solution is obvious:-)

Maybe you are looking for