USB not connecting properly 8800

I can no longer connect using USB to Blackberry Desktop Manager. Although the Device Connected (PIN) is showing correctly I can no longer synchronise or backup/restore etc. The 8800 is charging through the USB OK too. Tried different PCs and different USB cables. Is there a setting on the Blackberry I have inadvertantly changed perhaps?
Solved!
Go to Solution.

Remove the battery and reboot the BB. Leave it powered on for the battery pull.
For the USB cable...
Make certain your USB cable is connected to one of the PC's main rear USB ports. Not a USB hub, nor a monitor USB port, nor a USB port on the front of the PC.
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Similar Messages

HT1386 My iOS isn´t in device on the left hand, how can find it? or is it that is not connecting properly to the computer

My iOS isn´t in device on the left hand, how can find it? or is it that is not connecting properly to the computer

You need to update to 10.6.8 using Software Update.

Step "Start" is not connected properly in Visio

Hi All,
I have designed a workflow with 4 steps like start. process, approve, stop via DM. I am getting the following error while saving the workflow design
: Step start is not connected properly. I could not save the wrkflow design.
Here am giving the start step properties :
Name : Start
Check Out records : No
Duration Timeout : 1 wk
Cc: Notification : [owner]
Send Next step : [Anyone]
Split Job : [Anyone].
I have checked in the DM by selecting the record in the main table and righ clicking on that workflows->Add to job is also disabled.
I have checked the same by closing visio but still "Add to job" is grayed out.
Can anybody guide in the visio why am unable to save the
workflow design and Add to job is disabled?
Please help me out...
Thanks & Regards
Sireesha.

Hi,
Problem 1
Please check if the start step of the workflow is properly connected to the next step.Connect it properly and save.
Problem 2
Add to job is disabled
to resolve this problem go to workflow table in data manager select your workflow name in Records pane then go to Record Detail and check if the Active ="Yes" if not then assign Active="Yes".This will surely solve your problem.
Reward if helpful.
Regards,
Vinay Yadav
Edited by: Vinay Yadav on May 28, 2008 7:42 AM
Edited by: Vinay Yadav on May 28, 2008 7:48 AM

On my photosmart C4200 series printer, error message says USB not connected

I have a hp photosmart C4200 series it's saying the USB not connected. I made sure all connections were secure and still same message. I unplugged it and then plugged back in at tower and printer, still same. I changed out cable, still same problem. Is there anything else I can do aside from buying a new printer? Thanks, Jenn

Hi @jennirvinpest,
Welcome to the HP Forums!
I noticed that you are getting the error message that says your USB is not connected with your HP Photosmart c4200 series.
For further assistance, I will need some more information:
The Product/Model Number of your printer. Follow instructions in this link. Finding Your HP Product Model Number.
If you are using a Windows or Mac Operating System, and the version number. To find the exact version, visit this link. Whatsmyos.
If the printer is able to make copies.
If the power cable is plugged into a surge protector, or directly to the wall outlet. Issues when Connected to an Uninterruptible Power Supply/Power Strip/Surge Protector. This applies to Inkjet printers as well.
Thank you for posting, and hope to hear from you soon!
RnRMusicMan
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to say “Thanks” for helping!

Why does not connect properly macpro my motorola bluetooth headphones S10? I get a connection error message and there is no sound. (I want to use headphones to listen to music via bluetooth from my macpro)

Why does not connect properly macpro my motorola bluetooth headphones S10? I get a connection error message and there is no sound. (I want to use headphones to listen to music via bluetooth from my macpro)
the s10 works perfectly on my ipod touch 4g.

this is
ERROR HAS OCCURRED Bluetooth audio.
It failed to establish connection with their
audio device. make sure it is on and
in the range. you may need to restart the
audio section of the program you were using
STOP USING THE HEADSET WITH MICROPHONE.
ALSO HAVE A MOTOROLA BLUETOOTH SPEAKERS WHICH EQ5 work seamlessly with the Mac

Photosmart c4280 scanner "USB not connected" to Mac running 10.9.5

I've combed this forum and others and tried all the tricks. I can print and copy, so there's no USB problem. I've turned it all off and rebooted, downloaded an update, removed and re-added the printer, plugged, unplugged the USB and power cords. I've tried using image capture but it says it is not connected to a scanning device. I've reset the printer and uninstalled, per the directions in another thread. Now when I add the printer back, the C4200 series is not an option for software, since I deleted it (and software updates on Mac of course detects no updates available) so the default is "Generic PCL Printer" and of course, it still says the USB is not connected. What now? Thank you!

Hi @techtrampled,
Welcome to the HP Forums!
I understand that you are getting a USB not connected error using your HP Photosmart c4280 on Mac 10.9.5. I am happy to help!
I would recommend to go through the steps in this printer is offline guide, 'Printer is offline' Message Displays on the Computer and the Printer Does Not Print: Mac OS X.
Hope this guide helps, and have a wonderful day!
RnRMusicMan
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to say “Thanks” for helping!

I am getting error message on my hpc4280 "usb not connected". Gone through all the steps on HP site. Can anyone help please?

Getting error message on hp c4280 All in One printer when scanning. "USB not connected". Have gone through everything on HP help but reinstall of drivers. We have never been able to scan. Printing and copying are fine and have never been an issue. Can anyone help please?

So, is it connected via USB, or via Wifi/Airport?

PLEASE HELP! ETHERNET CABLE IS NOT CONNECTING PROPERLY WITH FIOS ROUTER

I recently purchased a time capsule to use in conjunction with my mac. When I am prompted to connect the ethernet cable from the lan port on my fios router to the wan port on the tc, the cable will not connect properly to the lan port on the tc. If I connect it from the lan on the fios router to the lan on the tc the green indicator lights up to indicate a connection but this does not help the wan port situation. I am able to locate the network I created from my mac but this tc network is not connected to the internet as indicated by the amber blinking light on the front of the tc. Also since creating this non working tc network, my fios signal is almost non existant! I am new to all of this so any help at all would be greatly appreciated!!!

Don't worry about the cable. For now.
Set the TC to bridge mode.. In bridge there is no wan port.. so you can use any port on the TC.
Test with the TC plugged in FIOS.. use in turn all the ports to see if it will work.
Do not change any setting but bridge the TC from default.. ie do not set extend wireless.. that will totally foul it up. Do not use join wireless, that will triple foul it up. Absolute default.. set TC to bridge... plug into the FIOS.. ethernet to any port that the light goes on.
Do a snapshot of the TC setup from airport utility and post.

Usb not connected 4280

i can copy but when i scan it says USB NOT CONNECTED but it is. i have had this printer FOREVER but recently had windows 8 installed. how can i scan and no im not going to do an uninstall at this point. i scanned manually recently but cant remember how i did it.

Hello @kirksandiego and welcome to the HP Forums, I hope you enjoy your experience!
I see you are experiencing issues scanning. I would like to help!
I'd suggest removing the cartridges and performing a power reset. Disconnect the power cord from the printer and the power outlet, then wait 60 seconds. After 60 seconds, plug the printer back in. Ensure you plug the printer directly to a wall outlet. Make sure to bypass any sort of surge protector or power bar.
I would also recommend downloading and running the HP Print and Scan Doctor.
Good luck and please let me know the results of your troubleshooting steps. Thank you for posting on the HP Forums!
Please click “Accept as Solution " if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks" for helping!
Jamieson
I work on behalf of HP
"Remember, I'm pulling for you, we're all in this together!" - Red Green.

Passport HD not connecting properly to Laptop

I have a passport portable hard drive, which was working fine. Today I connected it to my laptop, the blue power light came on, but it did not register properly in my computer. I didn't hear the normal prompts I usually do either when USB devices are connected to the laptop. It is drawing power because the power light comes on, but the computer does not seem to be able to read it. What can I do to access the hard drive? I tried reconnecting a few times and even used a different computer, with no success. Any advice or help would be appreciated, thanks.

I have a potential solution, but first need to ask what your level of computer knowledge is, as it's not "hard" but you could mess something up if you do it wrong.
If you like my post, or solution to your issue/question, go ahead and click on the little star by my name and/or accept the post as the Solution. It makes me happy.
I'm NOT an employee of Best Buy, or Geek Squad, though I did work as an Agent for a year 5 years ago. None of my posts are to be taken as the official stance that Best Buy will take on your situation. My advice is just that, advice.
Unfortunately, that's the bad luck of any electronic, there's going to be bad Apples... wait that's a horrible pun.

Usb not connecting

my iphone 5 was connected to my windows laptop first but after my laptop restarted it is not connecting it shows usb device not recognized and it shows there might be a problem with the cable but my iphone charges properly with it wagt should i do????

try connecting it with another computer it should show up as a camera so you don't have to sync
this should show if the issue is with the cable or if it's with the install of itunes on your computer that have gon bad

My iPhone 3Gs, after update to iOs 5.1, will not connect properly to the Alpine Bluetooth.

Now My iPhone will send only phonebook via Bluetooth, but not dialed calls or missed calls. Please help me!

touch me wrote:
it says ICCID: unknown
Not a good sign. Try forcing the phone into recovery mode & restoring it. If this fails, make an appointment at an Apple store:
Turn your phone off. Leave the USB cable connected to your computer, but NOT your phone, iTunes running, press & hold the home button while connecting the USB cable to your dock connector, continue holding the home button until you see “Connect to iTunes” on the screen. You may now release the home button. iTunes should now display that it has detected your phone in recovery mode, if not quit and reopen iTunes. If you still don’t see the recovery message repeat these steps again. iTunes will give you the option to restore from a backup or set up as new.

Nokia N70 and Pc Suite 6.6 not connecting properly

I am having problems connecting to my phone from windows xp and pc suite.
Whenever i try to "backup" or use "file manager" i get connection errors. Nokia connection manager is showing connected ok. When i click 'file manager' i can see the N70, but as soon as i try to 'explore' it by double clicking i get an error similar to 'Operation could not be completed'. (sorry not at home at the mo, experiencing parity error in my organic memory! ;-p)
History:
I Previously had Pc suite 5 installed and connected via bluetooth to my Nokia 6600. I believe the problem is the old PC Suite software as I can connect on a works laptop but not from my home pc. I have removed all previous Bluetooth, Nokia software via add-remove programs but still no luck.
I have tried renaming my memory card and even re-formatting and renaming, no luck.
System Details:
Windows XP SP1
PC Suite 6.6 Rev 18
Nokia N70
CA-43 usb cable
v2.0539.1.2 19-10-05 RM-84
Can anyone help? I really don't want to uninstall and re-install windows if i can help it!

sorry, i thought i was replying to a different thread i had allreayd posted my problem in, whihc is...
I had the firmware updated on my N70 today to get rid of the dreaded orange home screen at a nokia dealer, but when I try to connect to my PC it won’t work.
When I first got home and plugged it in via USB windows first told me the USB device was not reqocnised, so I pulled out the cable and put it in as advised. it seemed to be ok then, but just after i went to transfer some music over but it wouldn’t let me (as if my phone was not connected) and PC suit said I didnt have a phone connected, although I could see my phone under 'my computer' but couldn’t transfer any thing over.
So I downloaded PC suite again to make sure I had up to date software and drivers, I already had them it seemed but I unistalled and install them again just in case. But when I come to set up the connection the set up screen simply hangs, although the cable is working as windows makes that noise and it pops up to say N70 found, but then a second later says the install didn’t work, all the time the setup screen still hangs in the background.
I have tried every thing in this thread and others including doing the clean setup from nokia.
My firmware version: 3.0546.2.3.18-11-05RM-84
Windows XP SP2
Please help.
Thanks

Skype Not Connecting Properly

Starting today Skype refuses to connect. (it works fine on Windows, and the password wasn't changed). It just shows the connecting icon, and nothing happens.
Connects properly after around 5 minutes.
Last edited by *vitali* (2012-03-11 04:51:52)

I guess I am kind of glad someone else is having this problem more recently. I think it is tied to a recent update that Skype did. My in bound number stopped working right 2 weeks ago. They managed to fix some of it, so I do get calls now from Verizon and land lines - most land lines. I cannot get a call from a T-Mobile phone to save my soul.
It rings, and when I go to pick it up - it just disconnects in one second.
The party calling doesn't even hear it ring.
Many of them just give up and hang up.
It does also NOT forward nor offer voice mail
And it is not my settings - almost every other caller works just fine.
And I have the problem on multiple computers, multiple gadgets, android, ios, etc.
Skype support - help us out here.
Remember, we're all in this together, and I'm pulling for you.

"USB not connected"

HP Photosmart C4280: Hi, I had some work done on my CPU and the cables were disconnected. They are reconnected, but if I try to scan, it won't work and I get the message that the USB is not connected. Do I have to re-load the whole set-up? The printer is working fine otherwise.

Hello @kirksandiego and welcome to the HP Forums, I hope you enjoy your experience!
I see you are experiencing issues scanning. I would like to help!
I'd suggest removing the cartridges and performing a power reset. Disconnect the power cord from the printer and the power outlet, then wait 60 seconds. After 60 seconds, plug the printer back in. Ensure you plug the printer directly to a wall outlet. Make sure to bypass any sort of surge protector or power bar.
I would also recommend downloading and running the HP Print and Scan Doctor.
Good luck and please let me know the results of your troubleshooting steps. Thank you for posting on the HP Forums!
Please click “Accept as Solution " if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks" for helping!
Jamieson
I work on behalf of HP
"Remember, I'm pulling for you, we're all in this together!" - Red Green.

USB not connecting properly 8800

Similar Messages

Maybe you are looking for