USB Not working with digital devices
I've been Googling for a couple of hours now, but have not yet found this problem. As of yesterday, digital devices, including two cameras (a Nikon and a Kodak) and a HP Printer individually plugged into the USB port on my Toshiba Satellite 350 are not working. All use different USB cables and I have tried various ports on the laptop.These have all worked in the past and all but he Kodak have the latest downloads from their manufacturers. Oddly, the mouse and tablet work fine. I've plugged the cameras into another computer and they seem to work. Meanwhile, I've rebooted and restarted the problematic laptop several times, I've done all the Windows updates. The machine is running Windows Vista. Your suggestions will be most welcome! Thank you! Jeffrey B
Satellite L350-16A (PSLD8E-008006FR) Satellite L350-16A (PSLD8E-007007DU) Satellite L350-16A (PSLD8E-007004BT) Minor variations of even that model may depend upon the country. According to Ahorton763 in Msg 10, the method that Sublime14 proposed in Msg 2 worked for him/her. Have you tries it? With the battery and AC adapter removed, close the Power switch for half-a-minute. After that, re-attach those, press the Power button to turn the computer on, and then immediately press the F2 key while the Toshiba logo is displayed. Press F9 to restore the BIOS default settings, press F10, and then select Yes (Exit Saving Changes). The computer will restart.
Similar Messages
-
Why do my iPhone cords for my 5 say it is not certified and may not work with this device? It's the same cord that came with my phone. The only difference is the iOS7 update.
Maps took me to the completely wrong side of town for a long standing business in town.Hello margmcarlson,
Thanks for using Apple Support Communities.
For more information on this, take a look at:
Troubleshooting iPhone, iPad, and iPod touch accessories
http://support.apple.com/kb/TS2634
Restore iPhone, iPad, or iPod touch to its factory default state. You should rarely need to use this step with an accessory issue.
Best of luck,
Mario -
Email settings DO NOT WORK WITH iOS Devices
Vz keeps sending these "important" instructions for email port settings, BUT they do not work with iOS devices--iPhones and iPads. Last go around with this I spent over 16 hours trying to reconcile until an Apple Expert discovered "special" instructions for iOS device settings. Get with the program, Verizon.
So what are the special instructions?
-
M-Audio MIDISPORT UNO USB Not Working With Snow Leopard
My Snow Leopard installation worked fine except until I plugged in my MacBook to my Casio Privia with the M=Audio MIDISPORT UNO USB cable to run GarageBand. I'm getting a MIDI error which states it can't work with the latest operating system. It doesn't surprise me though for all the software and hardware driver updates that have to catch up to such a new OSX 10.6. I went to the M-Audio site to download the latest driver, but the drivers only were compatible with OSX10.5.8.
This is an alert at the site
Mac OS X 10.6 Snow Leopard Support Coming Soon
Avid/M-Audio working closely with Apple to offer support for OS X 10.6
Avid/M-Audio is pleased to hear that Apple has released Mac OS X 10.6 Snow Leopard. We’ve been working closely with Apple to bring Snow Leopard support to the M-Audio® product line, as well as the Pro Tools® product line and extended product families. We ask that all existing Mac users please wait to upgrade until we officially announce Snow Leopard support. Stay tuned for more information in the coming weeks.
This is a bit of a concern, because I need to get GarageBand running again with the MIDI hook ups. Is there a work around anyone knows about to get MIDI working with Snow Leopard.
Thanks SteveI ran into a similar problem. I discovered one thing which may help you out though. It works OK with my Yamaha P200 keyboard but it does not work with my Yamaha NP30 keyboard. I looked at the MIDI stream and the only difference seems to be that the NP30 sends a continuous stream of MIDI clock, whereas the P200 does not. My theory is that this clock stream is somehow confusing the driver. I can't seem to disable the MIDI clock on my NP30 but if your Privia has the ability to disable MIDI clock, then it may be worth a try as it will probably fix the problem until they come out with the proper drivers.
-
WRT54GX4 not working with PDA device
I got problem with my WRT54GX4, it can not working with the PDA device, like the Windows Mobile and Nokia E61 cell phone. The computers are ok. I did upgrade the firmware to the newest 1.00.20 but it didn't help at all. Does anyone has same problem or know how to solve it?
You need to check from the PDA Device if it is showing any option for network connection or wireless connection ...
Search for wireless access point & try to connect to it .... -
Devieces used with USB not working with applications
I got an ipod shuffle today and when i put it in it didn't do anything in itunes like it does with my nano.
I got a new camera, and i pluged that in using a USB cable and it connected but didn't do anything in iPhoto like my old camera did.
I wouldn't think this would happen with two devices, but it does.
What can i do?with the ipod no it should mount on the desktop at least. i had a problem with a friends iPod mini. it would mount on the desktop but not in itunes. try the iPod forums
-
USB not working with lion upgrade
I am having the same issues with my Mac mini and MacBook. The USB is not working! Help!
Have you upgraded to 10.7.3? Have you reset SMC and PRAM?
SMC:http://support.apple.com/kb/HT3964
PRAM:
Shut down the computer.
Locate the following keys on the keyboard: Command, Option, P, and R. You will need to hold these keys down simultaneously in step 4.
Turn on the computer.
Press and hold the Command-Option-P-R keys. You must press this key combination before the gray screen appears.
Hold the keys down until the computer restarts and you hear the startup sound for the second time.
Release the keys. -
M-Audio Fast Track USB not working with Mountain Lion
Went trough AVID.COM and M-Audio pages and there is no driver for mountain Lion. My Fast Track USB randomly produce NOISE sound when trying to open the interface to reproduce any sound.
It was working OK with Lion and Snow Leopard.now is working with teh 1.9.2 driver believe me work it!
-
Airport Express Not Working with All Devices
My airport express has been working fine. All of a sudden, it stopped working with iPad and MacBook, but iMac is still working fine. Firmware is updated. What to do? Help~~~!
Which version of Windows and Service Pack is your Dell PC running?
-
USB Ports not working with specific devices
So this one has me scratching my head. My USB ports on the back of my iMac are working except for a few devices. 1 being a logitech USB receiver, and 1 being a usb mp3 player. When I plug the received into the iMac the keyboard won't work, but when I plug my USB hub into the same USB port and the receiver into the hub it works fine. The mp3 player isn't working in any usb/hub (so that's a mook point).
Here's what I've tried to resolve this issue:
1. Reset iMac
2. Reset PRAM
3. Try every usb port on the back of the iMac
None of these have fixed my issue. Plugging it into the hub isn't a huge deal, but I'd like the option to use my USB ports as I wish without having to deal with this. Anyone have advice on a solution?It is not a matter of using your USB ports as you wish, it is a matter of what you are plugging into them and the power demands that what you plug into them makes on the system.
Not all USB ports or devices are created equal. How many ports are you using? What exactly are you plugging into the ports? What is the power demand of each item that you are plugging into each port? Are any of the USB devices self powered from their own separate power supply? Are all of the devices dependent upon the iMac for power?
It sounds to me that you have too many high power devices demanding more power through the ports than the iMac can accommodate. Is the USB hub self powered? If so, that is probably why it resolves your issue with the Logitech Unified receiver. There is very little info on this device on the Logitech website, so I could not ascertain its power demands.
Dah•veed -
Cisco 877 - not working with apple devices
Hello all,
I'm hoping someone can help me with a problem I have with my 877 adsl router.
A bit of background:
I have set this up as my home router to the internet, which is connected to a Linksys WRT54GL as a wireless access point.
My windows & Linux devices/laptops all work fine over this setup and connect without a problem
However, all my apple devices, phones and ipads don't fully work. I can get to google and a handful of pages, but not the store or games or facebook etc. (my daughter thinks its the end of the world - without FB and instagram)
If I take out the Cisco and put a Thompson router in, it all works fine. so I'm assuming it something with the Cisco config.
Below is the config I'm using on the router
Any pointers would be most appreciated.
ddhrouter#sh run
Building configuration...
Current configuration : 2292 bytes
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname ddhrouter
boot-start-marker
boot-end-marker
enable secret 5 mysecret
no aaa new-model
dot11 syslog
ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.1.1
ip dhcp pool CISCODHCP
network 192.168.1.0 255.255.255.0
dns-server 212.50.160.100 213.249.130.100 8.8.8.8
default-router 192.168.1.1
ip name-server 212.50.160.100
ip name-server 213.249.130.100
ip name-server 8.8.8.8
username cisco privilege 15 password 0 mysecret
archive
log config
hidekeys
interface ATM0
description ** adsl interface **
mtu 1452
no ip address
load-interval 30
no atm ilmi-keepalive
pvc 1/50
ubr 288
encapsulation aal5mux ppp dialer
dialer pool-member 1
dsl operating-mode auto
hold-queue 224 in
interface FastEthernet0
interface FastEthernet1
interface FastEthernet2
interface FastEthernet3
interface Vlan1
description ** local lan **
ip address 192.168.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly
hold-queue 100 out
interface Dialer0
no ip address
interface Dialer10
description ** adsl dialer interface **
ip address negotiated
ip mtu 1482
ip nat outside
ip virtual-reassembly
encapsulation ppp
dialer pool 1
ppp chap hostname myusername
ppp chap password 0 mypassword
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 Dialer10
no ip http server
no ip http secure-server
ip http max-connections 4
ip http timeout-policy idle 600 life 86400 requests 10000
ip nat inside source list 1 interface Dialer10 overload
ip access-list extended TerminalAccess
permit tcp host 192.168.1.0 any eq telnet
permit tcp any any eq 22
deny tcp any any
ip access-list extended no_telnet
deny tcp any any eq telnet
access-list 1 remark INSIDE_IF=Ethernet0
access-list 1 remark SDM_ACL Category=2
access-list 1 permit 192.0.0.0 0.255.255.255
access-list 110 permit icmp any any echo
access-list 110 permit icmp any any echo-reply
dialer-list 1 protocol ip permit
control-plane
line con 0
password password
no modem enable
line aux 0
line vty 0 4
access-class TerminalAccess in
password password
login
scheduler max-task-time 5000
end
ddhrouter#
all I'm after is a standard setup for my router. allow any out - deny any in.
Many thanks in advance.
Daveooo, you left your username, password, and enable in in clear text in the config you pasted, as well as not having an outside ACL applied and the VTY ACL allowing ssh from anywhere. Luckily the outside IP address isn't in the config or I'm sure someone would get ahold of your router....:) You should apply an outside access list and a firewall (I prefer CBAC firewall config for ease of use, but there is Zone based) to fix this. I assume ACL 110 was meant to be your outside ACL but it just isn't applied.
That being said Jody is likely right. PPPoE requires you to shrink your packet size (MTU/MSS) to allow room for the encapsulation that gets added to the packet. The command he supplied should fix this.
The 'ip mtu 1482' on the dialer interface may be too large as well. -
USB not work after unplug device
I had a satellite m645-s4050, after unplug a usb device, the USB ports from left side stopped working, the right side port still working, this is the second time it hapend to me, the first time i just update de BIOS and everyting work fine again, but now i can not update de bios again because i had the newest version.
Any help??Satellite M645-S4050
The techniques in this article apply to Windows 7 as well.
USB port may stop working after you remove or insert a USB device
I don't know if the Fix it runs though. If you try it, please let us know.
-Jerry -
SoundBlaster X-Fi Xtreme Audio: mic not working with digital out
I don't know if it is a design problem or a software problem, but with the digital output enabled, I cannot get the front panel mic input to work. Does anyone know the answer to this?
does anyone know since what version this has changed? Seem like the design is going backwards
-
I am reposting this question because I have not received an answer. Can anyone help me????
I have a Macbook pro & all of a sudden it's not reading a usb that was working earlier. I get a message "the disk you inserted was not readable..." I'm new to Mac & dont have much tech knowledge, so simple terms would be appreciated. Thank you.The drive you inserted has failed or was corrupted in some way that OS X can not read it. That error message seems farly clear to me. Drives can fail in a snap of your fingers.
-
Optus Huwaie USB not working with Macbook Air
I have a Macbook Air (mid 2011) running Yosemite 10.10.1
Using an Optus USB Modem (E3276 V2 4G) by Huwaie and it I think there is a compatibility issue. … I tried the modem on my Macbook .. no problem at all.
After launching on the Air, the USB dongle glows Blue which represent connection - status on Optus window says ‘connected' but there is in fact no internet connection at all and no kbps activity either way. I have seen a few similar posts on various forums but haven't so far understood what they are on about. Ideas? ThanksYou should be contacting the technical support of the Internet carrier for assistance. It is their responsibility to be compatible with Apple.
Ciao.
Maybe you are looking for
-
Hey again everybody. Was wondering if anybody else has had this issue that I have been having with my 360 directly connected to the verizon MI424-WR gateway router. The issue I am experiencing is when I turn on my 360 and it's just starting up and si
-
Dashboard prompt issue (Restricting Values in drop down) ????
Hi Friends, In my report I have "days to start" column which list almost 10,000 values ranging from -1000 to 5000. I need to create a prompt for this report on "Days to Start" column. When I create a prompt on Days to start with Operator "Greater tha
-
Abap MDM API query with OR operation
Hi experts, not sure this is the proper section for the thread, anyway; dealing with ABAP MDM API, is there a way to build up a query which involves several clause in OR conjunction? This is the scenario: I've got to extract several items on the basi
-
Can Mac OS be infected with the USPS email scam?
-
I want to make a Graph Drawing Servlet
I need to make line graphs, having days on the X axis and certain values on the Y axis. I need to show this on a JSP. I was thinking of making a servlet returning the image, but I'm not finding any Java solution for the graph drawing part. I would re