USB port on Cisco routers to connect 4G datacard

Hello
Can anybody know about the following questions?
1) Which router having USB port on which we can connect 4G datacard for internet connectivity?
2) Is there any inbuild USB port available on 1921-SEC/K9, 2921-SEC/K9, 3925-SEC/K9 routers for connecting 4G datacard for internet connectivity?
3) Is there any WIC card available that will be having USB port for connecting 4G datacard?
Regards,
Mukesh Kumar
Network Engineer
Spooster IT Services

1) Which router having USB port on which we can connect 4G datacard for internet connectivity?
None. USB ports do not have adequate capabilities to power up those kinds of devices.
2) Is there any inbuild USB port available on 1921-SEC/K9, 2921-SEC/K9, 3925-SEC/K9 routers for connecting 4G datacard for internet connectivity?
Cisco Fourth-Generation LTE Wireless WAN Enhanced High-Speed WAN Interface Cards Data Sheet
Q&A: Fourth-Generation LTE Wireless WAN Cards for Cisco Integrated Services Routers Generation 2

Similar Messages

USB port on cisco box

I have the cisco CHS335HDC verizon box .It has a usb port on the front .Is it possible to connect laptop to this to watch movies that are downloaded on laptop . Could you also watch them thru the dvd player in laptop
Thank you ,
Paul

AFAIK none of the VZ boxes (Moto or Cisco) support the USB port. I know for certain that the Moto boxes don't and if anyone knows different regarding the Cisco boxes please feel free to correct my statement.
If a forum member gives an answer you like, give them the Kudos they deserve. If a member gives you the answer to your question, mark the answer as Accepted Solution so others can see the solution to the problem.

I updated to IOS6 on my IPAD 3 and IPad shows a pic of USB port and ITunes but will connect and/or turn on even when I connect to my computer.

I updated to IOS6 on my IPad and the screen went blank then showed a picture of a USB plug and arrow pointing to ITunes but nothing else happens. I cannot restore, recover or sync anything.... Please help!

You will probably need to restore using Recovery Mode. You can read about it here.
http://support.apple.com/kb/ht4097
Or you can follow this.
Recovery Mode Instructions
Disconnect the USB cable from the iPad, but leave the other end of the cable connected to your computer's USB port.
Turn off iPad: Press and hold the Sleep/Wake button for a few seconds until the red slider appears, then slide the slider. Wait for iPad to turn off.
If you cannot turn off iPad using the slider, press and hold the Sleep/Wake and Home buttons at the same time. When the iPad turns off, release the Sleep/Wake and Home buttons.
While pressing and holding the Home button, reconnect the USB cable to iPad. When you reconnect the USB cable, iPad should power on.
Continue holding the Home button until you see the "Connect to iTunes" screen. When this screen appears you can release the Home button.
If necessary, open iTunes. You should see the recovery mode alert that iTunes has detected an iPad in recovery mode.
Use iTunes to restore iPad.

Airport Extreme won't show the WD external hard drive I plugged into the USB port. How do I connect my external hard drive to my network?

I plugged in my WD external hard drive into my Airport Extreme via the USB port. The hard drive will not show up in the disk section in the airport utility... How do I hook an external hard drive up to the airport extreme? I have tried 2 different WD hard drives. I must be missing something!!!
Thanks!

To be recognized by the AirPort for sharing, the WD HDD has to be formatted in either HFS+ (ideal) or FAT32. The easiest way to format the HDD is to use the Disk Utility in OS X.

How do I find the address of my usb ports so that I can connect a telescope to the macbook. I have tried various commands on terminal and all I get is 'directory or command not recognised'.

The telescope instruction says open a Terminal and put in ls/dev/* and other such things and all I get back is that none of them are recognised.
JeffersE

Why don't you call the telescope company for support and let them explain it to you. Usually there is software involved with those types of telescopes and if that software doesn't support Mac, it won't matter how or what USB port you plug it into because no drivers or anything will load for it.

Imac usb ports disabled and nothing is connected

iMac 27inch Late 2007 USB Ports Disabled Again!
Has happened before and took forever to fix it. Nothing specific fixed it last time and nothing I know was the direct cause. Each time different OS, different location, different year, different cables etc etc.
Now, reset everything, moved everything, changed everything - still nothing. No USB ports work. iMac still has pop up "USB devices disabled..."
Taking into Apple unless someone can tell me what 10 pages of google hasn't - what a bloody stress and waste of time!

Disconnect all peripherals from your computer.
Resetting your Mac's PRAM and NVRAM

Iphone no longer recognised by usb ports!

my replacement iphone 4 is not recognised by any of my usb ports now and i cant connect to itunes to sync all my music. ive tried everyting ive come accross on google and here! please help??

Define "everything". If you don't tell us what you've done already, you're going to get a whole lot of responses that you've already tried. If you tell us what you've tried, we can narrow it down to stuff you haven't tried yet.

Help, 10.6.8 update, all usb ports stop working after 10hrs

I've been running 10.5.8 for ever and finnaly tried to update to 10.6.8.. After I did it, the usb ports all kick out any connected devises after around 10 or so hours. I ran of the install disk, using disc utillty, disk repair, and repair permisions a few times and it did not help.
I did the install a few times again to try to see if it would help and didnt.
i tried an erase and install and migrated everything over from my orignal back up external drive that is running 10.5.8 and issue is still there.
My old 10.5.8 back up external drive works fine and does not have this issue, and I have been using that as my start up drive instead and working from there. But that is not really a solution and a temp work around.
Any suggestions would really help. thanks!

I have a early 2008 macbookpro 2.8 duel with silver keys.
I purchaed the 10.6 disk from the apple store. I've had the machine for years and purchased it refurbished from apple.
I did the erase and install and migrated everything over from external drive, then did update to 10.6.8 and the usb ports still would stop working after a few hours.. Then I read on another apple community forus to reset pram, and pull out the power cable, take out the battery and hold power key for 5 seconds, then restart. that seemed to fix usb issue so far..
But overall my computer seems to be running slower then when using just 10.5.8 and it did not wake from sleep once and I had to force power off and restart.. But maybe its just getting used to 10.6.8. we will see..
Also, on another note, my battery is totally dead, and I can only run computer with power cable.. Will this affect things? it never did with 10.5.8..
Oh, on my erase and install, I just did the simplest version and did not do the full erase to zero using he advanced security measures.. I just did the one where it writes on top of everything..

Changing the TCP port on async ports in Cisco router

Hello,
My goal is to replace old terminal servers from a factory environment.
These terminal servers act as a aggregation point of terminal equipment (printers and factory automation).
Software used in this factory writes to these devices using ip-address of the terminal server and TCP-port starting at 10001, where the last number is a port number.
The problem is that in Cisco equipment, I can not find a way to change the tcp port to this 1000x. The only option would be to change the softwares TCP-port to Cisco default 200x, but this is not the solution I am looking for. This is because the switchover should be done when the machines are running, and the time window is to short to make changes in the factory software.
Is there a way to change the logical TCP-port for Cisco routers asyncronous lines (HWIC-16A) to 10001-16?
Marko Tuhkunen

So i figured out that i can use the archive tar /create command:
To copy the entire flash towards TFTP:
archive tar /create tftp://X.X.X.X/flash.tar flash:
Now i will have to insert the new flash and probably format it first towards the correct file systems. Then i will have to use the next archive command:
archive tar /xtract "Here i am unsure of the syntax, i want to be copying and extracting the tar I backed up from the old flash"
After these steps are complete can i just reboot the router with the new flash card, won't there be any issues, since the startup config is on the NVRAM it will load the config properly, and i haven't seen any boot parameters but they shouldn't pose any issues since i'm not changing the flash slot.
Thanks for your assistance

945P internal USB port problem

Power exceeded on USB Port 945P motherboard - NO DEVICES CONNECTED
Part Number: MSI 945P Platinum Socket 775
CPU: Intel Pentium 4 640, 3.2 GHz
Memory: Corsair 512MBx2 PC4300 DDR2 533MHz
Operating System: XP Pro
On the motherboard, I have added more external USB port (case mounted), these ports are connected to the mobo on the connector JUSB2.
Now, Windows gives an error stating that the power has been exceeded and must reset or close the port.
There is no device connected to these USB ports, only the wires that lead from JUSB2 connector to the case mounted USB ports.
Did any of you had the same problem?? Thanks.

Have you checked to see if the USB, that is mounted to the Front of the case has any Shorts?
You might also want to remove the USB that is plugged into the Header on the MOBO.
One more thing you might have hooked up the USB header wrong.

CD/DVD, SD and USB ports aren't usable

Hello, I recently discovered multiple problems with my Satellite M305-4848 laptop running Vista Home Premium Service Pack 2. I hadn't used any of these recently so I am not sure when the problems started or what might have happened to cause them.
First when I put in an SD card which works fine on my other PC's the system responds that the card needs to be formatted. But if I try to format it the system says it cannot be formatted. I have tried multiple cards that work fine on other PC's.
Second when I try to use any of my USB ports the devices don't work. I tried my USB 3 1/2" flex drive and it also says it needs to format the disk which reads fine on a different PC's USB port. I tried my connecting my IPOD (which I have done many times in the past) and the PC says the IPOD data is corrupted and that I need to do a restore to my IPOD.
Lastly, my CD/DVD drive does not recognize the data on a prerecorded disc. For example, when I put in commercially created DVD video disc and double click on the D: drive on My Computer the system opens the drive and shows a popup saying "Please insert a disc into drive D:".
I have tried using the Control Panel Device Manager and doing an Update Driver Software on the obvious drivers but it hasn't helped. I also tried using the F2 Setup and Load Defaults and I ran a newly updated Norton Scan which found no problems.
I'm not sure what to try next. Any ideas? WiFi works and I have no problems with items on my hard drive.

I discovered the answer to my own problem and anyone else out there who needs it here it is: If you have itunes installed on your computer and cd/dvd device is not working do a system restore to a time prior to the dl of itunes. Check to make sure your cd/dvd works again. If it does, then all you need to do is make sure your ipod is NOT connected to your computer while you download itunes again. Should fix the problem.

Faulty USB port message & froozen iPod with picture of dock connector

Hello,
I've got a problem with a faulty USB port. I've been connecting my 3rd gen iPod (2003, touch wheel, dock connector) to my windows using computer for year - but today it doesn't work. I downloaded the latest version of iTunes and was about to syn/upload my iTunes library to my iPod but then computer says I have a faulty USB connection. There is nothing wrong with the USB ports. The iPod shows a picture of the dock connector, and then shuts down. I've tired resetting the iPod but the same thing happens. Does anyone have any suggestions?
Andrea

the new updater is screwing up 3rd and 4th generation ipods. you can buy a new ipod at your local electronics store.
Joe

MBA will not allow me to use both usb ports at the same time.

My MBA will not allow me to use both usb ports at the same time. as soon as i plug the second in the first is disabled. trying to use a modem and printer.

What kind of peripherals are you connecting? Sometimes if an external device is drawing too much power, then it will shut down one of the USB ports. Make a test connecting two usb flash drives, it should work ok.

Does the apple ipad2 have a usb port

Does the ipad2 have a usb port?

Yep the camera connection kit (as per Swebbie and Barry) is the way to go. £26 from Currys Digital. Have not tried for general files but for photos with the SD adapter that comes with it is great.
But as Swebbie says what did you intend to use for?

My USB ports won't recognize any devices. Thoughts?

I am still using Mountain Lion, and I have been warned about updating. My USB ports will not recognize or connect to any external devices. Any thoughts?

Try resetting the SMC. Use the procedure for "a battery you should not remove yourself".
http://support.apple.com/kb/ht3964

USB port on Cisco routers to connect 4G datacard

Similar Messages

Maybe you are looking for