USB ports and cable; S5-1554

The 2 front USB ports on my Slimline Desktop S5-1554 do not work. I noticed that a 5-wire cable (female connector with 3 holes on the top row and 2 holes on the bottom row) from there leading toward the motherboard is disconnected. Where/how does it connect? I see available 10-pin (male) F_USB1, 10-pin F_USB2, 11-pin LPC_DEBUG, and 2-pin Flash Overdrive male connections are available. The wire colors in my 5-wire cable are green, orange, red, yellow and white.
Thanks.

The standard USB header(motherboard) is 5x2 with pin 9 missing. The view. What your describing is not USB.
I am a volunteer. I am not an HP employee.
To say THANK YOU, press the "thumbs up symbol" to render a KUDO. Please click Accept as Solution, if your problem is solved. You can render both Solution and KUDO.
The Law of Effect states that positive reinforcement increases the probability of a behavior being repeated. (B.F.Skinner). You toss me KUDO and/or Solution, and I perform better.
(2) HP DV7t i7 3160QM 2.3Ghz 8GB
HP m9200t E8400,Win7 Pro 32 bit. 4GB RAM, ASUS 550Ti 2GB, Rosewill 630W. 1T HD SATA 3Gb/s
Custom Asus P8P67, I7-2600k, 16GB RAM, WIN7 Pro 64bit, EVGA GTX660 2GB, 750W OCZ, 1T HD SATA 6Gb/s
Custom Asus P8Z77, I7-3770k, 16GB RAM, WIN7 Pro 64bit, EVGA GTX670 2GB, 750W OCZ, 1T HD SATA 6Gb/s
Both Customs use Rosewill Blackhawk case.
Printer -- HP OfficeJet Pro 8600 Plus

Similar Messages

Hy won't my ipod touch 5G connect to my computer or itunes? I've tried new USB cables, different USB ports and uninstalling itunes and reinstalling.

Why won't my ipod touch 5G connect to my computer or itunes? I've tried new USB cables, different USB ports and uninstalling itunes and reinstalling.

See
iOS: Device not recognized in iTunes for Windows
- I would start with
Removing and Reinstalling iTunes, QuickTime, and other software components for Windows XP
or
Removing and reinstalling iTunes and other software components for Windows Vista, Windows 7, or Windows 8
However, after your remove the Apple software components also remove the iCloud Control Panel via Windows Programs and Features app in the Window Control Panel. Then reinstall all the Apple software components
- Then do the other actions of:
iOS: Device not recognized in iTunes for Windows
paying special attention to item #5
- New cable and different USB port
- Run this and see if the results help with determine the cause
iTunes for Windows: Device Sync Tests
Also see:
iPod not recognised by windows iTunes
Troubleshooting issues with iTunes for Windows updates
- Try on another computer to help determine if computer or iPod problem

Accidentally switched off iMac at mains. Now only goes to grey sceen when switched on. Have removed all USB's from ports and cable from screen rear but still grey screen. What next?

Accidentally switched off iMac at mains. Now only goes to grey sceen when switched on. Have removed all USB's from ports and cable from screen rear but still grey screen. What next?

I would reset the PRAM
http://support.apple.com/kb/HT1379
or
I would try and reset the SMC
http://support.apple.com/kb/ht3964

I have an Apple MacBook Pro with 2 USB ports and a MiniDisplay Port. I also have an HDTV with a HDMI port. How can I use the TV as a display without any tethering wires between my computer and the TV?

I have an Apple MacBook Pro with 2 USB ports and a MiniDisplay Port. I also have an HDTV with a HDMI port. How can I use the TV as a display without any tethering wires between my computer and the TV? I have a MiniDisplay Port to VGA adapter, but there are two issues with it: The new display doesn't have a VGA port, and even if it did, I wouldn't want to have my mac constantly attached to the display by a cable. I was looking for a way to use the TV as a display without any wires. Is there some type of bluetooth setup I could use? Please let me know if you have any suggestions.

As I wrote above, I think you should look into the Apple TV yourself. The best place to find information about what it can and can't do and to ask your own specific questions is probably in the Apple TV forum, here:
https://discussions.apple.com/community/appletv/appletv

The iTune cannot detect my iPhone. I have already tried all methods suggested, including re-installling iTune, re-activating Apple Mobile Device, plugging in various USB ports, and etc. I use windows 7. How can I solve this?

The iTune cannot detect my iPhone 4S. I have already tried all methods suggested, including re-installling iTune, re-activating Apple Mobile Device, plugging in various USB ports, and etc. I use windows 7. How can I solve this?

The new cable is completely new, and my computer can detect the phone as a drive, and battery charging is ok. So I believe the USB cable works properly. It is so weird that just iTune itself cannot detect the phone, and it is of the most updated version. What else can I do? Thanks.

USB Ports and AGP Video Card on same IRQ

I've got a tough one. I have 6 USB ports. Call them 1,2,3,4,5,6. Ports 1 and 2 work fine with my new USB 2.0 80GB External Harddrive. This pair of ports 1 and 2 are direct into motherboard.
However system crashes when I plug USB 2.0 External Drive into ports 3,4,5,6. These are Dports with cables that plug into the MB. One of these Dports has the four error lights which are all green. Western Digital has cautioned against sharing this drive with other IRQs. Says that the video card and the WD harddrive require dedicated IRQs...but I have no control of how W XP assigns them.
Ports #3-6 work fine with mouse, scanner, and printer etc. However they fail when trying to use WD External Hardrive.
I also checked IRQ settings and IRQ 16 is used for a USB Port and for my MSI AGP video card. I believe this conflict is the cause of the problem.
So help..how do I fix this dilemma?
I have Windows XP and see no way to change IRQs.
BIOS does not even show IRQ as a choice..only 1-15. Also BIOS is latests version for my MSI 845G Max L MS-6580 mother Board. USB drivers are all Intel. Video Card Is MSI AGP MS-8878 G4Ti/MX 420 w TV out. Bios and Drivers are current.
How can I run the USB 2.0 External Harddrive in Ports 3-6?

I did load new Intel INF Drivers and AGP drivers yesterday.
No luck USB Ports 3-6 still fail with External Hard Drive.
I'm not clear on how to turn back on AICP or ACIP. BIOS?
Also not IRQs 16-23 are listed with active devices on the Device Manager
16 has a USB Controller at 24c2
16 also has AGP video card
17 has Audio '97
17 also has Fast Eternet.
18 has USB Controller at 24c7
19 has USB Controller at 24c4
23 has PCI to USB Interface.
Port 3-6 do work fine with mouse, dig cam, Scanner, printer. These ports only fail with External Harddrive plugged in. Ports 1and2 work fine with external HD??
So question is how do I check on the IRQ ports using AIPC or APIC...or whatever the name is...thanks folks.

Hi guys well huge issue my Ipod 4th generation shuffle died and I tried to chrge it I plugged it into the USB port and the red light came on and after 5 seconds turned off the whole Ipod is dead and I've tried in wall chargers as well that doesn't charge

Hi guys well huge issue my Ipod 4th generation shuffle died and I tried to chrge it I plugged it into the USB port and the red light came on and after 5seconds turned off the whole Ipod is dead and I've tried in wall chargers as well that doesn't charge what should I do is there a solution or should I claim my warrenty and have it fixed??

Also my Itunes and computer won'r reconize it

Hi skydiver, I have ios7.4, I tried two different USB ports and it still doesn't show,up on my desktops in my computer as iPad so I can't click it. If it was there I would open and see all my photos, and YES it ask me DO I trust this computer! several tim

Hi skydiver, I have ios7.4, I tried two different USB ports and it still doesn't show,up on my desktop in my computer as iPad so I can't click it. If it was there I would open and see all my photos, and YES it ask me DO I trust this computer! several times.
The apple tech on the phone, went to my control,panel
Went to my devices. Original iPad showed up,there In red and then he had me go,to apple website, download something and it said it could configure to my computer.
Is,finally answer,to me was go to the apple care,one on one appointment, and it's my "software"
A man I know told me "Apple at store, won't be able to do,anything for me"
That's not very positive.
What else? Can't I download iPad drivers,into my computer?

iPad not appearing in iTunes
http://www.apple.com/support/ipad/assistant/itunes/
iOS: Device not recognized in iTunes for Mac OS X
http://support.apple.com/kb/TS1591
iOS: Device not recognized in iTunes for Windows
http://support.apple.com/kb/TS1538
iTunes for Windows: Device Sync Tests
http://support.apple.com/kb/HT4235
IOS: Syncing with iTunes
http://support.apple.com/kb/HT1386
Apple - Support - iPad - Syncing
http://www.apple.com/support/ipad/syncing/
iTunes 10.5 and later: Troubleshooting iTunes Wi-Fi Syncing
http://support.apple.com/kb/ts4062
 Cheers, Tom

I have hp laptop dv9009us one day all the USB ports and webcam camera stopped working

I have hp laptop dv9009us one day all the USB ports and webcam camera stopped working, I had windows XP and tried all solutions posted on online forums didn’t work, I upgraded to windows 7 and still not working, please note that the USB is detected in device manger and it says working properly but he webcam is not detected at all, also when I connect any device to USB it gives it power and I even can charge my cell phone but it doesn’t detect any device. Is there any genius out there that can help me?
Also after I installed windows 7 I went o system information----software environment--- system drivers, and I found all USB drivers stopped by the way this was the case in windows XP as well
usbccgp            Microsoft USB Generic Parent Driver   c:\windows\system32\drivers\usbccgp.sys         Kernel Driver   No            Manual Stopped           OK      Normal No       No
usbcir   eHome Infrared Receiver (USBCIR)    c:\windows\system32\drivers\usbcir.sys Kernel Driver   No       Manual            Stopped           OK      Normal No       No
usbehci Microsoft USB 2.0 Enhanced Host Controller Miniport Driver c:\windows\system32\drivers\usbehci.sys            Kernel Driver   No       Manual Stopped           OK      Normal No       No
usbfilter            AMD USB Filter Driver           c:\windows\system32\drivers\usbfilter.sys          Kernel Driver   No            Manual Stopped           OK      Normal No       No
usbfltr   Razer Copperhead Driver         c:\windows\system32\drivers\copperhd.sys       Kernel Driver   No       Manual            Stopped           OK      Ignore No       No
usbhub Microsoft USB Standard Hub Driver    c:\windows\system32\drivers\usbhub.sys           Kernel Driver   No            Manual Stopped           OK      Normal No       No
usbohci Microsoft USB Open Host Controller Miniport Driver c:\windows\system32\drivers\usbohci.sys          Kernel Driver   No       Manual Stopped           OK      Normal No       No
usbprint            Microsoft USB PRINTER Class           c:\windows\system32\drivers\usbprint.sys          Kernel Driver   No            Manual Stopped           OK      Normal No       No
usbstor USB Mass Storage Driver        c:\windows\system32\drivers\usbstor.sys           Kernel Driver   No       Manual            Stopped           OK      Normal No       No
usbuhci Microsoft USB Universal Host Controller Miniport Driver         c:\windows\system32\drivers\usbuhci.sys            Kernel Driver   No       Manual Stopped           OK      Normal No       No
uwbusb            UWB Bus Control USB-Miniport Driver          c:\windows\system32\drivers\usbuwbmini.sys    Kernel Driver   No       Manual Stopped           OK      Normal No       No

Did you ever get this resolved? I am having the same problem and have tried just about everything for my dv9000.

So I stuck a key into one of the USB ports and then a message came up and it crashed straight away and now it won't turn back on.(the message was to do with the USB port taking to much power when there wasn't anything besides the key) help?

Please help! My mac is about 6 months old and I was just playing with my keys and stuck it in the USB port and then it crashed and won't turn on, it's not picking up the charger (the little led light isn't on) and pressing the power button does absolutely nothing

Don't be so surprised, people have stuck worse things in worse places before and it was on purpose
+1
How am I meant to get the the apple menu if the laptop won't then on
Reset the SMC first. If this doesn't work, reset PRAM. Move down troubleshoot with links below. First, SMC reset for MBP models 2009 and later:
Shut down the computer.
Plug in the MagSafe power adapter to a power source, connecting it to the Mac if its not already connected.
On the built-in keyboard, press the (left side) Shift-Control-Option keys and the power button at the same time.
Release all the keys and the power button at the same time.
Press the power button to turn on the computer.
Note: The LED on the MagSafe power adapter may change states or temporarily turn off when you reset the SMC.
Intel-based Macs: Resetting the System Management Controller (SMC)
Resetting your Mac's PRAM and NVRAM
Resolve startup issues and perform disk maintenance with Disk
Troubleshooting: My computer won't turn on

If I already have an Airport Express Base Station, can i hook an external hard drive into it's USB port and use that hard drive with Time Machine?

If I already have an Airport Express Base Station, can i hook an external hard drive into it's USB port and use that hard drive with Time Machine?

No, and that shouldn't be done with an AirPort Extreme or Time Capsule.
(66017)

Lost the keyboard backlight, use of my USB ports and camera shows as disconnected. How do I fix this?

Please help. I'm still a MAC rookie.
I unplugged my Pedometer from one of the USB ports on my Macbook Pro. Ever since then, I lost the backlight to my keyboard. I did some troubleshooting on these discussion boards and found a few with similar issues, but most of the discussions were old and the solutions were out of date. As one of them advised, I checked to see if my Isight Camera was still connected and it wasn't. I also tried plugging a few different things into both USB ports and neither of them worked either. So whatever caused this, it's affecting all 3 of these things. I don't know if my Pedometer is old/bad and it "short-circuited" the USB port and everything else along with it when I unplugged it or if something coincidentally went bad at the same time that I removed it.
I read some old answers from the discussion boards where they suggested a Command (R) system recovery reboot. But I also read that that really doesn't help on newer operating systems. I am on OS X. Here is my Hardware Overview:
Model Name:          MacBook Pro
Model Identifier:          MacBookPro5,4
Processor Name:          Intel Core 2 Duo
Processor Speed:          2.53 GHz
Number Of Processors:          1
Total Number Of Cores:          2
L2 Cache:          3 MB
Memory:          4 GB
Bus Speed:          1.07 GHz
I did recently purchase a backup drive and I THINK I previously backed everything up properly. But, I can't even plug that into the USB port now to see if I
can somehow use that to fix this since the ports aren't working. I have no idea what to do. Does anyone have any suggestions? Please!?
Thanks in advance!

Reset PRAM. http://support.apple.com/kb/PH4405
Reset SMC.     http://support.apple.com/kb/HT3964
Choose the method for:
"Resetting SMC on portables with a battery you should not remove on your own".

Updated OS X Mavericks and now USB ports and MS Office apps won't work. How do I fix this?

I updated my MacBook Pro (mid 2012) to OS X Mavericks 10.9.4 and now my USB ports and MS Office apps won't work. What do I do to fix this?

What system version were you running before you updated to 10.9.4? Another 10.9.x or something earlier?
What version of Office? 2004, 2008, or 2011?
Were you aware that Office 2004 does not run on recent versions of the system?
When you say your USB ports do not work, on what are you determining that?
Were you aware that Mavericks does not display external disk volumes by default?

After downloading itunes, I hooked my iphone up to my computer and told it to restore. Got an error message, 1015, and it wouldn't restore my phone so now all I get on the screen is a pic of a usb port and an image of itunes. Anyone know what I can do??

can anyone tell me how to restore my iphone? Itunes will not let me and now my screen just has a usb port and itunes on it?

Error 1015: This error is caused by attempts to downgrade the iPhone, iPad, or iPod touch's software. This can occur when you attempt to restore using an older .ipsw file. Downgrading to a previous version is not supported. To resolve this issue, attempt to restore with the latest iPhone, iPad, or iPod touch software available from Apple.
What this means is you have to delete your .ipsw file (it may be corrupted or old) and attempt to restore your iPhone again.
Where the .ipsw file is found:
Mac                         - ~/Library/iTunes/iPhone Software Updates
Windows XP           - C:\Documents and Settings\[username]\Application Data\Apple Computer\iTunes\iPhone Software Updates
Windows Vista/7     - C:\Users\[username]\AppData\Roaming\Apple Computer\iTunes\iPhone Software Updates

HT204384 USB Port and SD card port not working

My USB ports and my SD card port do not work. They have both worked previously, but now do not read anything on my new Mac Book Pro.

If you are still under warrantee, take advantage of it and go to the Apple store.
Ciao.

USB ports and cable; S5-1554

Similar Messages

Maybe you are looking for