USB ports no longer charge when PC is off since installing Supercharger

I have an MSI Z77A-G41 (MS-7758) Rev 3.0 running Windows 8 Pro 64 bit - 8GB RAM running the latest BIOS and drivers (used MSI LiveUpdate)
Charging devices with my front USB ports always worked when the PC was off, UNTIL I installed Supercharger from MSI's LiveUpdate utility. Charging does appear to be faster while the PC is on, but it no longer charges my devices when powered off like it did before I installed Supercharger.
I then uninstalled Supercharger, and the PC still will not charge devices when powered off.
I ensured 'EuP 2013' is DISABLED via BIOS ... not sure what else to do and why USB charging while powered off is no longer working. :(

OK, I just figured out what the problem is.
JUSB1 and JUSB2 control the 2 USB ports available to the front of my PC. With my board (MSI Z77A-G41 (MS-7758) Rev 3.0), JUSB1 is NOT red, but it still charges devices connected to it when powered off.
In my situation, the top USB port runs to JUSB1, the bottom runs to JUSB2.
I just realized my device was plugged into the bottom USB port which runs to JUSB2. The top port connected to JUSB1 works fine when the PC is off.   
Issue resolved. Thanks for your replies people, I'm good to go! 

Similar Messages

  • TS2634 When I connect iPad to Macbook Pro through USB Port or even charge my iPad via the apple adapter, it has no response at all. I can only charge my iPad when I totally shut off the iPad. Pls advise.

    When I connect iPad to Macbook Pro through USB Port or even charge my iPad via the apple adapter, it has no response at all. I can only charge my iPad when I totally shut off the iPad. Pls advise.

    Well ... the charger is the original charger and just checked and confirmed it is a 5.1V charger. How come? Next is why when i connect my iPad via original usb cable, no response from macbook pro? used to sync with iTunes now totally dead.

  • HP M8100N pavilion usb ports no longer recognizes external drive

    My Paviilion M8100N USB ports no longer recognizes my external drives. I have VISTA premium operating system.

    The entire document and tutorial can be found here.
    I am a volunteer. I am not an HP employee.
    To say THANK YOU, press the "thumbs up symbol" to render a KUDO. Please click Accept as Solution, if your problem is solved. You can render both Solution and KUDO.
    The Law of Effect states that positive reinforcement increases the probability of a behavior being repeated. (B.F.Skinner). You toss me KUDO and/or Solution, and I perform better.
    (2) HP DV7t i7 3160QM 2.3Ghz 8GB
    HP m9200t E8400,Win7 Pro 32 bit. 4GB RAM, ASUS 550Ti 2GB, Rosewill 630W. 1T HD SATA 3Gb/s
    Custom Asus P8P67, I7-2600k, 16GB RAM, WIN7 Pro 64bit, EVGA GTX660 2GB, 750W OCZ, 1T HD SATA 6Gb/s
    Custom Asus P8Z77, I7-3770k, 16GB RAM, WIN7 Pro 64bit, EVGA GTX670 2GB, 750W OCZ, 1T HD SATA 6Gb/s
    Both Customs use Rosewill Blackhawk case.
    Printer -- HP OfficeJet Pro 8600 Plus

  • HT201412 My iPhone 4S stops charging a few seconds after being connected to the USB, it will, however, charge when it is switched off.

    iPhone stops charging a few seconds after being connected to a USB slot, it will charge when switched off is I think it must be a software issue.

    HAve you tried using a different power chord? If the power chord is not the issue, it could be the power supply inside your mac.

  • Has anyone ever experienced the situation where plugging in the USB connector to the charging source (high-power USB port or Apple charger) halfway, then pressing it in firmly, results in the iPad not charging?

    Has anyone ever experienced the situation where plugging in the USB connector to the charging source (high-power USB port or Apple charger) halfway, then pressing it in firmly, results in the iPad not charging?

    It's highly likely that there is a poor connection in the phone - either a pin in the dock connector or internal wiring harness.  No software fixes or "tricks" would work, but I would recommend restoring in iTunes, first using a backup and if needed restore as a new phone. 
    Otherwise, opening and repairing the phone takes some tech knowledge that can't be relayed here.  Apple doesn't repair phones other than replacing batteries (not inconceivable that you have a bad battery), but offers "out-of-warranty" replacement (refurb) phones for $149 (US).  3rd party iPhone repair centers may be able to fix it for less.  Google to find them,
    Tried soft and hard resets
    FYI, there's no such thing as "soft" or "hard" resets in iPhone terminology.  There is only one phone reset. You'll see those terms thrown around by technically ignorant posters, but they mean different things to different people and are actually archaic, 1980s PC terms that have nothing to do with iPhones.
    See the User Guide, Appendix B.

  • HT201412 my phone will no longer charge, when i plug in the charger the phone says - charging is not supported by this accessory.

    My i phone3GS will no longer charge - when i plug in the charger the phone says "charging is not supprted with this accessory"

    do you have any other chargers? is it the charger that came with the phone? is it giving the same issue when plugged into the computer and into the wall? do you have an apple store near you to try the chargers there? can you buy a new charger at target or something? have you rebooted the phone?

  • My Iphone will only charge when it is off???

    I just got my iphone 4 about around june of this year and ever since two or three days ago I plugged my phone in because it was dead and it would not charge but when i got it home to charge it it charged all the way and not today its doing the same thing it will only charge when it is off and then as soon as the cord powers it back on it will stop charging and say 10 pecent batt left... I bought a new cord and it still does not charge my phone idk what to do this is really annoying i also tried my charger in another iphone 4 and it charged that phone so its not the cable it has to be the phone but the phone is brand new and never has been damaged i am going to verizon to hopefully get a new phone but in the mean time looking for any suggestions or tips or maybe somene is having the same problem too

    Also when i have the charger plugged in after the phone dies it will show the charging batt symbol but as soon as it powers back on it says 10% battery life again and then when i power it off WITH THE CHARGER STILL CONNECTED the phone will not show the charging battery symbol again whihc means i have to take the charger out and put it back on and it dose it all over again charges with off but as soon as it powers on automatically it stops charging

  • My iphone3gs has died, it just started to vibrate and carried on for several minutes, then just stopped . Now I cant switch it on or off I just have a black screen It was fully charged when it happened and since then I have tried holding down the sleep bu

    My iphone3gs has died, it just started to vibrate and carried on for several minutes, then just stopped . Now I cant switch it on or off I just have a black screen It was fully charged when it happened and since then I have tried holding down the sleep bu

    iOS: Unable to update or restore

  • Xperia T doesn't charge when power is off

    My Xperia is not charging when power is off. Normally it showed a battery when I put this phone in the dock for charging, but nothing happens. It will only charge when the power is on....What can I do to make the phone charging with power off?

    http://talk.sonymobile.com/t5/Xperia-T-TX/Sony-Xperia-T-does-not-power-on-most-likely-after-low-battery/m-p/279859#M1938  http://talk.sonymobile.com/t5/Xperia-T-TX/Xperia-T-LT30p-doesn-t-turn-on-no-lights-when-plugged-no/m-p/363892/highlight/true#M6425  

  • Brand new ipod nano will work when attached by cable either to a power adaptor or usb port but stops immediately when disconnected, despite being put on charge with different adaptors. Battery indicator remains constantly on lightning flas symbol and whit

    My Brand New ipod nano (sold to me two days ago by Apple as replacement for previous ipod nano -15 months old and therefore out of warranty - which had suddenly stopped functioning altogether) will operate only when attached by cable to either power adapter, usb port on my laptop or when playing on a docking station. When detached, it stops playing and screen goes dark and it will not respond to any buttons, despite being charged several times for many hours on different chargers. The battery indicator stays on lightning flash symbol on white background and has only momentarily shown fully charged symbol once !
    I am baffled as to why this new ipod has a similar problem to the old ipod.
    Is there a virus out there which can have this effect and which I may have picked up on my Pc and have inadvertently transferred to both ipods when sync-ing ?
    My PC has Norton anti-virus software.
    Any suggestions , please ?

    Sounds like the Nano has a faulty battery.  You should be able to have Apple swap it out again for you at no cost.
    B-rock

  • Restoring Your Nano When The USB Port No Longer Recognizes The Device

    I can't say for certain if its coincidental or not but as soon as the latest update of v9 for iTunes came out, my computer stopped recognizing my iPod (1st Gen Nano) through all the USB ports.
    First, I tried the Nano on a different computer with Windows Vista but the the latest version of iTunes had also been updated on that machine. The laptop also would not recognize the device through any of the USB ports.
    Second, I switched cables. Same problem.
    Third, I reset the device. Same problem.
    Fourth, I tried to update the drivers on the device manager. Same problem.
    Fifth, I uninstalled iTunes per Apple's uninstall instructions and that was to no effect.
    Now my last option is to restore the device, however because I can't get it to be recongized on any computer I own- I don't know how to do this? Do I take it to an Apple store? Is there a manual way to restore the device to factory settings since every computer I have access to won't recognize the device?
    Thanks!

    I have exactly the same problem. After updated to the latest version of iTunes 10, my 5th gen ipod stopped being recognized by my Windows 7 Computer.
    I've tried:
    1. Un/reinstalling Itunes 10, then updating to 10.1 or whatever was the latest one as of 9/30/10.
    2. Using a different iPod USB cable to connect to the computer.
    3. Using a different USB port.
    4. Trying the iPod on multiple computers.
    5. Manually selecting the driver within Device Mananger in Windows 7 from "Unknown USB Device" to "Apple USB iPod Driver".
    6. Restarting my computer, multiple times.
    7. Resetting my ipod "Menu+Select buttons for 6-10 seconds"
    From what I understand I could resolve this problem by restoring the iPod to its factory settings, but since I can't get it to be recognized in a computer I am stumped.
    This will be my third iPod in 4 years that has crapped out (out of warranty of course) If I can't get this fixed I'm buying a Zune.

  • There is a problem with the charging cable that wont let my iPad charge. it is probably the little usb thingy. it does charge when it is out of power, but as soon as it turns on it stops charging. anyone got a fix for it? mail me at simenrognli@hotmail.no

    My chargers little USB port probably is the fail. it lets my ipad charge only when it is completely out of power, but as soon as it turns on, it stops charging. Any tips on what i can do? The charger is new and has worked until today. i cant bring it to the store because it was bought in my neighbour country Sweden. Thanks in advance.

    - Try another cable.
    - Try another charging source
    - Inspect the dock connector on the iPod for bent or missing contacts, foreign material, corroded contacts, broken, missing or cracked plastic.
    - Make an appointment at the Genius Bar of an Apple store. You can still go if your country has Genius Bars
      Apple Retail Store - Genius Bar                 

  • Upgraded to Snow Leopard and USB ports no longer work completely

    Hi!
    So my wife is using my older (from 2007) 15in macbook pro. We just installed Snow Leopard (from Tiger) and the USB ports are no longer functioning correctly.
    Previously, intermittently (between restarts) one of the USB ports wouldn't work well, but restarts always fixed it. This would happen maybe once or twice a month.
    Currently, neither the left or right USB port work well. Both will run a USB mouse and charge an iphone, but neither will recognize the phone or a card reader as plugged in.
    We've tried restarting. Tried turning off, unplugging, removing the battery and holding down the power for 5 seconds and restarting.
    Nothing is working. Does anyone have any tips on how to fix it?
    (The iphone is recognized by my macbook pro, so it's not the wire or the phone, at least as far as we can tell.)
    Thank you kindly in advance.

    I think it's time you upgraded to a newer version of Photoshop.

  • Some USB ports no longer working after installing Mountain Lion?

    Some of my USB ports are no longer working after installing Mountain Lion onto my 21' 2011 iMac. I used to plug in my iphone 4S and charge it, or transfer files onto my iPad but none of the ports no longer work to do this. Funnily enough, other equipment plugged into the works. I have tried changing the cable. Any ideas?

    In my experience, the USB ports on the back of an Apple monitor can be re-enabled simply by unplugging and plugging back in the device in question. You might also check to see that the USB Monitor hub shows up in System Profiler. My Apple monitor USB ports experienced no changes in moving to 10.4.7.
    bd

  • USB ports no longer working after 10.4.7 update

    Hi, I ran the latest update (10.4.7) on my machine which is a G4 Quicksilver PowerPC. I have an Apple 17 inch flat screen display that has two USB ports attached. I had my keyboard plugged into one of the USB ports on my flat screen. After the update both USB ports on the flat panel no longer work! I can use the USB ports directly off the G4 itself and it works fine. Has anyone seen this issue? I guess I am stuck now until Apple decides to fix this?
    Thanks,
    Rob

    In my experience, the USB ports on the back of an Apple monitor can be re-enabled simply by unplugging and plugging back in the device in question. You might also check to see that the USB Monitor hub shows up in System Profiler. My Apple monitor USB ports experienced no changes in moving to 10.4.7.
    bd

Maybe you are looking for