USB problem with msi (nforce 1)k7d420

USB problem with msi (nforce 1)k7d420
i encountered problem when using my apacer audio steno mp3 player with my nforce(which i don`t hav any problem when using with any VIA chipsets)
it detects and install the device automaticly but when i want to access it,it just gives me error msg
windows xp pro service pk1
nforce nvidia drver v2

http://www.nforcershq.com/forum/viewtopic.php?t=30003
may be ive not loaded it yet

Similar Messages

Problems with msi p35 neo 2

Default problems with msi p35 neo 2
pc works fine when using windows and the net and emails
only when using 3d mark or games do i ever get problems
just help in getting the hole story 6 months ago got a msi neo2 install all my old components core 2 duo 4 gig ram form a diffrent board works fine but never used it playing games just used for the net and email shoping seamed to work fine but
tryed playing a game 2 months later command and conquer 3 pc was some times freeze or graphics artefacts on screen assumed vga card faulty got another graphics card geforce 8600gts installed still the same in the last month got round to playing with the pc again and installed new g7 780 watt power supply and ati hd 4870 graphics card
now i can use 3d mark some times it will go through once or just freeze or 3d mark stops the test
temps on the board (from msi dual core center temps cpu 33oc system 47oc)
memory voltage 2.1
any one know the settings for the ram
more details you need
System Details
MotherboardEdit Value
msi p35 neo2 fr
Motherboard BIOSEdit Value
latest
CPUEdit Value
core 2 quad 6600
CPU Overclock SpeedEdit Value
none
CPU HeatsinkEdit Value
standard intel that come with cpu
CPU Idle TempEdit Value
N/A
CPU Load TempEdit Value
N/A
MemoryEdit Value
******* xms2 2x2 gb ddr2 part no cm2x2048 6400c4dmx
Memory VoltageEdit Value
N/A
Video Card(s)Edit Value
ati hd4870
Video Card SpeedEdit Value
N/A
Sound CardEdit Value
onboard
PSUEdit Value
g7 780 watt power extreme
Hard Drive(s)Edit Value
mator dimondmax 21
Optical Drive(s)Edit Value
N/A
Other CoolingEdit Value
3 80mm fans 1 frount 1 back 1 side
ModsEdit Value
N/A
Operating SystemEdit Value
windows 7

Quote
******* xms2 2x2 gb ddr2 part no cm2x2048 6400c4dmx
Quote
memory voltage 2.1
Make sure that the memory timings are not set to 4-4-4-x but that they are set to the defaults values (5-5-5-x). Also ensure, that the memory clock speed is not set to anything higher than 400 MHz (=DDR2-800). The voltage at these settings should not need to exceed 1.95V. So please lower it accordingly. In case the freezes still occure, please run memtest86+ to check your memory for errors.
Quote
msi dual core center
Please get rid of that tool for all further tests. Uninstall it completely from your system as it is known to cause crashes and freezes on its own terms when running.

I have a small problem with MSI GF4 MX 420

Hi,
I have a small problem with MSI G4MX420-T(S+C) ( MS-8878 ). Exactly with nVidia WDM Video Capture (universal), which " can't be turned on " by Windows XP.
I have also new drivers ...
Could someone help me?
Asus A7V333
Athlon 1700+
128 MB RAM
Thanks !!!

If you only have 10 seconds of content in a 15-second composition, then you need to either add more content or shorten your composition.
You can shorten the composition by changing the duration in the composition settings.
Since you're obviously very new to After Effects, I very strongly recommend that you start here to learn After Effects.

USB problem with K7T266-Pro

I have an USB problem with Logitech Cordless Wingman Gamepad. I have dowloaded the newest version of logitech gamepad, and the VIA drivers for motherboard K7T266-pro. I also tried to install the USB filter rc1, but the problem remains.
Here is how the problem occur:
1. On start up, the gamepad is detected and ready to use.
2. While I am playing a game, the usb device is reconnecting a lot. I turned of the "Allow this device to turn off to save power" in device manager under all USB root hub. But the problem remains.
3. After a while, when I have been playing for a while, the gamepad turns off, and the usb device is not recognized error message appears. Under device manager I now have a Unknown Device under USB.
4. To get it function again I have to restart the computer.
Anybody who knows the answer for this ?

I have a similar problem but with my Logitech optical mouse. It's also using the usb port and it keeps disconnecting and reconnecting the device in Win XP. I use to have Win2000 and I experienced the problem but not as often as now. Also in Win2000 there wasn't an annoying sound when a device would connect and reconnect, and not to mention when your playing a game and the mouse quits for 1/2 a second, really annoying! Sometimes it will quit completely and I have to either physically reconnect it or reboot to get it working again.
I have recently tried fixing the problem:
a) I flashed my old Bios and put in ver 1.9 from this site
b) I've updated the Via 4in1 drivers
c) I've updated the mouse drivers that come from Logitech.
None of these updates helped. I've taken my mouse to work to see if it does the same thing, but so far so good. My pc at work is running Win2000 but different MB. I don't think there is anything wrong with the mouse. Although I haven't tried using the PS/2 adapter that came with it and see if it behaves the same way. I have a feeling the mouse will work fine, but kinda sucks cause I have usb and I have to revert back to PS/2 just so it works properly.
I've read on the Via Hardware forum some people having the same problem but with an Abit board. They changed something in their Bios to resolve it. If anyone has any ideas, maybe changing something in the Bios that has to do with the usb ports, I would greatly appreciate it.

[Athlon64] Problem with MSI RS480M2-IL

Hi all,
I have problem with MSI RS480M2-IL. My problem is My temperature is very high... around 55-60c ... i am using AMD 3000+ Venice and no OC... and SpeedFan unable to detect my Voltage usage... Aida32 also same... 1 more thing is when i tried to run SiSoft Sandra 2005... it will take alot of time to load, sometime will just hang. i Test PCMark04 and found only got 3k for average mark... my friend getting 4k+ and we are using same spec... Below is my Spec:-
MSI RS480M2-IL
AMD 64 3000+ Venice E3
Bios Version 3.8
Geil PC3200 DDR400 2.5-3-3-6
Maxtor 60GB HDD 7200RPM 2mb
Verudium Power Vortex 420W
Hope some one can advised me what to do... my score too low and my board detect temperature and voltage is not accurate... Hope MSI Engineer will look thought and help me... Thank for Viewing !

the underlying "Who's fault is it?" question: AMD64 VENICE CORE (E3) PROCESSORS? or MSI RS480M2-IL MOBOS?
so far, ALL users with this proc/mobo combination HAVE the high (or incorrect) temperature issue. replacing the mobo obviously will not resolve the issue but replacing the proc with one that is NOT a Venice E3 core, does the trick. but of course, not everyone will have the privilege of exchanging their damned proce via the retailer specially if it's beyond the first 21 days of purchase.
in my case, my retailer refused to have the E3 proc replaced with the 'corrected' E6 version no matter how hard you explained the known issues with the E3. no chance of AMD recalling the E3 cores since problems with are only isolated to the particular MSI RS480M2 boards.
so for users that are and will be stuck with this combination, what is the solution then to the temperature issue? in my opinion, it's up to MSI to perhaps release a bios update that will correct this. another important thing to consider is the question: IS MY VENICE CORE INDEED OVERHEATING OR IS IT JUST THE MSI MOBO SHOWING INCORRECT READINGS? the proc overheating in actuality is obviously a lot different thatn just having an incorrect bios temp readings.
based on what i have observed, my Venice core displays the correct cpu temps (33-35*C) when being used on a MSI K8 Diamond mobo. placing the proc back to the R2480M2 board shows a very unusual 61-63*C bios cpu temp. furthermore, if i touch the stock heatsink/fan cooler that i have (for both motherboards), it really does NOT seem to be extremely hot to think that the cpu is actually overheating. in addition, my system using the RS480M2 performs well and has no spontaneous shutting down problems whatsoever. of course, my sense of touch is not as accurate as a thermometer but more or less, if you consider all the points i mentioned, most of us can say that the whole issue is just a matter of incorrect cpu reading.
perhaps the ATI chipset is the one to blame since i have notices as well that the Venice core processors do not seem to have this high temp problems with MSI's K8 mobos with the NVIDIA chipsets.
one last question: so do you guys think that this problem can be resolved by a simple bios revision? (as a dell tech guy, i do know for a fact that bios updates resolves overheating error messages in Inspiron/Latitude laptops)

Usb problem with VirtualBox 4.1.2.

Hello all
I have a usb problem with my VirtualBox 4.1.2.
I installed VirtualBox 4.1.2 with VirtualBox Extension Pack 4.1.2. on vista 64 bit host
but when I run Win 2003 guest I get the following :
Failed to access the USB subsystem.
Could not load the Host USB Proxy Service
(VERR_FILE_NOT_FOUND). The service might not be
installed on the host computer.Can any one help on how to resolve this ?

I too an facing the same problem.
if u have some solution then plz mail it to me.
regards
Dinesh Singh
Nucleus Software Exports Ltd
[email protected]

USB Problem with iMac

I have a USB problem with a 2007 iMac.
It appears that 1 of the usb ports is faulty, when in OS X 10.6.2 I constantly get "because a usb device is drawing too much power" popup. Usually 3-5 popup eventually.
I used Boot Camp to boot into Windows 7 and Device Manager can see the ICH8 Family USB Universal Host Controller - 2832 as a problem. I can disable it without an problems.
The question is: Is there any way to either disable that pop-up warning in Os X or disable that specific port so I don't get the pop-ups.
I performed all updates and things like PRAM reset and SMC reset.
Its not under Apple Care if your wondering.
Thanks,
Message was edited by: DrWickman

So does that mean all the ports work properly, even after getting that message?
If you start up from your Mac OS X installation disc (a different Mac OS X system), do you still get this error message? You can do so by inserting the disc and restarting with the C key held down. When you get to the Installer screen, you can do things like run Disk Utility from the Utilities menu. Does that message still appear?
Also, you said you reset PRAM and SMC, but make sure you followed these procedures
http://support.apple.com/kb/HT1379
http://support.apple.com/kb/HT3964
Apple recently changed the procedure a bit. While going through it disconnect ALL cables. If you have been connecting the iMac to a crowded or old power strip, connect to directly to a wall outlet, at least during this test. Power it up initially with nothing connected, except the power cord. Note if that message appears. If it does not, connect just your keyboard/mouse, use it that way for a while, and note if that message appears. If all is well, connect the remaining peripheral devices.
I don't know of a way to disable that message without disabling all the USB ports.

Problems With MSI K8N Neo Platinum

Posting some probems I have face and wondering if you folks have experience similar problems. I bought 2 and bot hahve same problems (sold both of it). Another friend of mine have also same problems with the board.
1. SATA 1/2 don't work properly. I have detection problems using SATA ports 1/2. The comp will not detect my IDE devices and hang at POST screen. Reboot/reset don't solve the problem. I have to turn off and on to get it to work. Problem is only sovled after switching to SATA 3/4.
2. Network disconnection problem. The NIC will auto disconnect and reconnect back by itself, esp. when under overclocked conditions.
3. Cannot overclock much using DIMM slot-1 esp. when mem is over 230MHz. Must change to slot 2/3. Even so, I do face BSOD stating an USB driver is the cause of the issue.
4. Comp will sometimes unable to reboot at FSB between ~210-240MHz. 250Mz and above seems OK.
Now, I am using Abit KV8 Pro 1.1 and it works fine though. No FSB reboot issues. I am using 1.1 with latest BIOS, thus not AGP/PCI lock issues. Hope MSI will fix those problems mentioned ASAP cause my Abit don't work with mobile A64s. :(

Seriously, I have absolutely no idea. It may be a QC problem, it may be a design problem, its may be BIOS or others. The only thing I know that after I jump ship to Abit KV8 Pro 1.1, all these problems are gone. Only problem is that Abit don't support mobile A64s.
BTe, just another problem or maybe over conservative restrictions. When using DDR333 RAMs, the BIOS will not allow you to manually set it to 400. Thus at 200MHz FSB/HTT, your RAM is stuck at 166MHz. Pretty stupid restriction I have to say.

Problems with msi - G41M-P28

Hi, I've problem with my new msi G41M-P28 mainboard. My computer freezes when I plug out usb flash drive when I'm into bios. In windows it's ok .. I hope.. but when I'm into bios and when I plug out usb flash drive the main problem (computer freezes) remains. With usb mouse computer not freez at all .. I''ve tried to test it with different usb sticks and it freezes .. not only in bios .. it freezes in dos too. Any solutions? :(

Hardware list of my pc:
CPU: Intel Pentium Dual Core E5700 3.0Ghz
RAM: 2GB Kingston KVR1333D3N9, PC3 - 10600 CL9 240
HDD: Seagate Barracuda 7200.12 500GB
PSU: Fortron FSP350-60APN, output: 350W, AC Input: 200-240V, 2.5A, 50-60Hz
Mainboard: msi G41M-P28, Bios version : v26.6
OS: Win 7 Pro 32Bit
DVD-ROM: SpeedPlus SuperWritemaster SH-S223

Problem with MSI X58 Platinum SLI - IOH temperature !

Hi guys.
I have this PC configuration:
- MSI X58 Platinum SLI ( Bios Version 3.8 - http://img822.imageshack.us/img822/6707/161020101249.jpg )
- Intel Core i7 930 2.80 GHz box ( with Intel Turbo Boost running sometimes at 3.06 Ghz )
- MSI GeForce GT240 1GB DDR5 128-bit HDMI
- Corsair 6GB DDR3 1333MHz CL9 XMS3 Triple Channel Kit ( sets to AUTO and running at 1066 Mhz )
- Corsair CMPSU-750TXEU
- Ordinary case ( http://img828.imageshack.us/img828/4200/161020101246.jpg & http://img29.imageshack.us/img29/8480/161020101247.jpg ).
- Windows 7 Ultimate 64 bit.
I bought my PC components 2 months ago, so they are new.
Now, guys I think that is a problem with my motherboard. When I turn on the computer in Bios I have this temps: CPU – 30 C (86 F); IOH – 71 C (159 F); System 30 C (86 F) - http://img687.imageshack.us/img687/394/161020101242.jpg. After 2 minutes the temperatures are: CPU – 34 C (93 F); IOH – 82 C (179 F); System 41 C (105 F) and 2 more minutes later the temperatures are: CPU – 34 C (93 F); IOH – 84 C (183 F); System 43 C (109 F). After 30 minutes of doing nothing I have this temps: CPU – 35 C (95 F); IOH – 85 C (185 F); System 42 C (107 F) -
Guys it is normal with IOH temperature ? I am a little worried about it ( to be honest I am more than “a little” … I am worried a lot ).
Ok, I know I don’t have a good case but in 3 weeks I should receive this Thermaltake Spedo Advance Case (http://www.thermaltakeusa.com/Product.aspx?C=1121&ID=1829) and I will buy a new CPU cooler ( I don’t know yet wich one – maybe Corsair CWCH70 or Noctua NH-D14 but I have to see the case first … to be sure there is a plenty of space for those coolers ).
Pls help me with that IOH temperature. It is normal ? What if I intend to make a little OC ( lets say CPU to 3652 Mhz and RAM to 1333 Mhz … but also I will ask for your support ! ) my motherboard will burn ?
If it is necessary I will contact my retailer and send him back the motherboard but … I like MSI a lot.
Thx guys for your support !

Hey guys,
Here is a nice cheap alternative.
Here is my story about the same issue. I found it after looking at why my computer freezes sometimes. Not very often but enough for me to do some investigation. I noticed my IOH temp was a whopping 117 degrees Celsius. lol. Surprised my mobo didn't burn out by now. I wanted to evaluate the situation with the heat sink and decided to take it off. After taking it off I found extremely crusty purple compound on board the chipset and the heatsink. I took me FOREVER to scrape it off. it was almost like a cement which I found odd. After scraping and cleaning the surfaces with alcohol, I placed some silver compound on and proceeded to put it back on.
Well, upon hooking everything back up I was still at 95 to 103 degs. Now I started to really look at the options to replace this. I had SLI config which means I had to do something clever with the southbridge as well. A nice thermaltake chipset solution w/fan and a low profile copper southbridge with shipping was about 45 bucks. Hmm ... This is a sure fix from the threads I have read and its really kid of expensive to fix a simple defect. the problem is not necessarily with the heatsink not being sufficient. Its the combo of the compound used vs the amount of pressure applied between the heatsink and chipset. It was completely unacceptable. I knew this right away when I was watching the temp and then I would press on the top of the IOH heatsink and I would watch it drop another 15 degrees in less then 10 seconds. The springs are extremely weak and not effective at all in transferring the heat from the NB.
Here if my fix. Cost me less than a dollar at the hardware store and it works ideal thus far. Do this at your own risk. Doing this will probably void any warranty too. All my problems are solved and I am running at 57 degrees, YES, 57 degrees with the stock heatsink and no additional cooling.
For one scrape all that old crap off like I did. Apply your new compound. But when you go to replace your heatsink, use the following method. The trick is to use metal screws with a mobo washer, original springs from the plastic studs and a nylon locknut. Use screws that are the same diameter and length (maybe a tad bit longer) as the plastic retainer studs. Also grab a few of those red nylon mobo washers too, were gonna need them as well.
After scraping and applying compound, reassemble as follows. Screw with washer inserted into the back of the mobo so the threads are out front. The plastic/nylon washer is betweeen the screwhead and the back of the mobo as a insulator. Put the heatsink on. With the threads thru the heatsink already, put the springs on and start spinning on the locknut. I torqued the nut down on the spring until the spring almost became fully compressed. The purpose of the spring here is really to prevent you breaking something and at the same time using the max force of the spring since it weak to begin with. Thats why we need to compress it down pretty much all the way. There will be little to no room in the spring at this point. The heatsink at this point should be pretty solid to the board as well. I noticed with the plastic studs before the heatsink would wobble if you gave it a little rocking back and forth before. Not this time. Shouldn't move much if at all. Remember not to torque down too much. You don't want to go beyond the springs compression. Even if you did by accident, its better then not using a spring at all. If you feel that it starts to feel tight when torquing, you torqued too far. Stop an backup a 1/4 turn or so. It is also very important to make sure both torques are equal on both sides as well. Alternate sides when torquing down. I could tell by how much thread I had left on both sides and by looking for any uneven sides.
To summarize, the compound is a problem no doubt. After you resolve the compound issue, its all about the adequate pressure between the heatsink and the IOH. Much like the amount of pressure needed between your CPU and your heatsink give or take. And the pressure that would be as an aftermarket solution like the thermaltake chipset cooler. You dont see cheesy springs on that. Wake up MSI. Simpy using a more effective spring could save MSI some cash in the long run. I envision a leafsprin design like the thermaltake chipset one. The heatsink design could be better, sure, but the design itself is not the problem. Replace the heatsinks if you would like to, if your overclocking and stuff. Funny, this board I have is a refurb too and only had it for a few weeks. Figured they would have done something about it.
Sorry the pics are not the best. Here is about as close as I could get to the finished product

Problem with MSI Board and MSI Geforce 4 with Windows XP

I have a MSI 845E Max(MS-6566E)
MSI Geforce 4 - 420
Celeron 1.7 gig
Soundblaster Live
2 Network Cards
and the usual stuff.
I have loaded Windows 98 on my system and it works fine. But then I load Windows XP on and the system starts rebooting. After it reboots my video resets itself and I have to load it back in. I will then reboot and sometimes it will work, sometimes it will not. I try playing a game or even searching the net for awhile, but out of the blue the system will give a very quick blue screen and reboot. And of course when it boots up the video is reset. I loaded all the drivers I could find on MSI's website and used every video driver made by Nvidia and MSI. If I do a Windows XP update to my system the computer will not even boot up. it will just keep rebooting when it is trying to bring up the login screen. Anyone else run into this with Windows XP?

My system sometime freezes. Why ???
P4 1.8A GHz Notrtwood, 256MB PC2700, MSI Geforce 4 TI4400, SB Live 1024
Check my logs:
1)
// Watchdog Event Log File
LogType: Watchdog
Created: 2002-07-23 20:03:27
TimeZone: -60 - Central Europe Standard Time
WindowsVersion: XP
EventType: 0xEA - Thread Stuck in Device Driver
// The driver for the display device got stuck in an infinite loop. This
// usually indicates a problem with the device itself or with the device
// driver programming the hardware incorrectly. Please check with your
// display device vendor for any driver updates.
ShutdownCount: 108
Shutdown: 0
EventFlag: 1
EventCount: 1
BreakCount: 1
BugcheckTriggered: 1
DebuggerNotPresent: 1
DriverName: nv4_disp
DeviceClass: Display
DeviceDescription: NVIDIA GeForce4 Ti 4400
HardwareID: PCIVEN_10DE&DEV_0251&SUBSYS_87111462&REV_A3
Manufacturer: NVIDIA
DriverFixedFileInfo: FEEF04BD 00010000 0006000D 000A0BD6 0006000D 000A0BD6 0000003F 00000008 00040004 00000003 00000004 00000000 00000000
DriverCompanyName: NVIDIA Corporation
DriverFileDescription: NVIDIA Compatible Windows 2000 Display driver, Version 30.30
DriverFileVersion: 6.13.10.3030
DriverInternalName: nv_disp.dll
DriverLegalCopyright: (c) NVIDIA Corporation. All rights reserved.
DriverOriginalFilename: nv_disp.dll
DriverProductName: NVIDIA Compatible Windows 2000 Display driver, Version 30.30
DriverProductVersion: 6.13.10.3030
2)
// Watchdog Event Log File
LogType: Watchdog
Created: 2002-08-12 18:53:23
TimeZone: -60 - Central Europe Standard Time
WindowsVersion: XP
EventType: 0xEA - Thread Stuck in Device Driver
// The driver for the display device got stuck in an infinite loop. This
// usually indicates a problem with the device itself or with the device
// driver programming the hardware incorrectly. Please check with your
// display device vendor for any driver updates.
ShutdownCount: 235
Shutdown: 0
EventCount: 8
BreakCount: 8
BugcheckTriggered: 1
DebuggerNotPresent: 1
DriverName: nv4_disp
EventFlag: 1
DeviceClass: Display
DeviceDescription: NVIDIA GeForce4 Ti 4400
HardwareID: PCIVEN_10DE&DEV_0251&SUBSYS_87111462&REV_A3
Manufacturer: NVIDIA
DriverFixedFileInfo: FEEF04BD 00010000 0006000D 000A0C0A 0006000D 000A0C0A 0000003F 00000008 00040004 00000003 00000004 00000000 00000000
DriverCompanyName: NVIDIA Corporation
DriverFileDescription: NVIDIA Compatible Windows 2000 Display driver, Version 30.82
DriverFileVersion: 6.13.10.3082
DriverInternalName: nv_disp.dll
DriverLegalCopyright: (c) NVIDIA Corporation. All rights reserved.
DriverOriginalFilename: nv_disp.dll
DriverProductName: NVIDIA Compatible Windows 2000 Display driver, Version 30.82
DriverProductVersion: 6.13.10.3082
3)
// Watchdog Event Log File
LogType: Watchdog
Created: 2002-09-07 22:22:41
TimeZone: -60 - Central Europe Standard Time
WindowsVersion: XP
EventType: 0xEA - Thread Stuck in Device Driver
// The driver for the display device got stuck in an infinite loop. This
// usually indicates a problem with the device itself or with the device
// driver programming the hardware incorrectly. Please check with your
// display device vendor for any driver updates.
ShutdownCount: 408
Shutdown: 0
EventCount: 14
BreakCount: 14
BugcheckTriggered: 1
DebuggerNotPresent: 1
DriverName: nv4_disp
EventFlag: 1
DeviceClass: Display
DeviceDescription: NVIDIA GeForce4 Ti 4400
HardwareID: PCIVEN_10DE&DEV_0251&SUBSYS_87111462&REV_A3
Manufacturer: NVIDIA
DriverFixedFileInfo: FEEF04BD 00010000 0006000D 000A0FC9 0006000D 000A0FC9 0000003F 00000008 00040004 00000003 00000004 00000000 00000000
DriverCompanyName: NVIDIA Corporation
DriverFileDescription: NVIDIA Compatible Windows 2000 Display driver, Version 40.41
DriverFileVersion: 6.13.10.4041
DriverInternalName: nv_disp.dll
DriverLegalCopyright: (C) NVIDIA Corporation. All rights reserved.
DriverOriginalFilename: nv_disp.dll
DriverProductName: NVIDIA Compatible Windows 2000 Display driver, Version 40.41
DriverProductVersion: 6.13.10.4041

VCORE PROBLEMS WITH MSI P35 NEO F

To see if I can help or at least explain what's happening, buy a MSI P35 NEO F for using a quad, the topic is as follows handling vcore is rare
First thing I can not put less voltage that the cpu brings default, second what happens next if bios setting 1.3250 vcore for Quad, once in both windows everest, cpuz, like others programs tell me that this placed on 1.40 vcore which is excessive for the speed at which the quad, this is so in this mobo? Their story that was installed version 1.20 bios which handled vcore%, the upgrade to version 1.40 and is now handled in decimals (numbers) vcore, but still the problem
You pull more vcore which setting in bios and if you want to download the vcore eg put 1.26 vcore not let you because it takes the vcore default of cpu minimum.
i'm not crashing or problems with the temperatures, but nobody likes to have more vcore's necessary.
Wonder because being rookie of this mobo, maybe there's some bios version that fixes this bug or someone knows something else, thank you guys
C2Q Q6600
2 X 1GB G.SKILL 6400
PSU 550 MODULAR TOPOWER
-- SORRY FOR MY ENGLISH --

You can slap 1.6v in that CPU and temps won't rise that much.
Core 2 Duo/Quad operates @ 1.250-1.425, anywhere in between those values is perfectly stable for Intel stock cooler and frequency.
Absolutely nothing to worry about. But if you want to complain about >1c I really can't see the sense in that.

Going on week FOUR of problems with MSI NEO-2-S :/

Mainboard: MSI Neo2-S, BIOS Rev. 1.5x (whatever Live Update sent me)
RAM: GeiL 1GB (512x2) PC-3500 Matched pairs
CPU: P4-2.4c
HD: WD 1200JB Special edition
Cooling: Stock intel, lapped @ 800 grit
PSU: 450W
Video: MSI Geforce 4 TI-4200 64MB
O/S: Windows XP Pro SP1A, IE 6.x latest security patches
DX: Direct-X 9b
BIOS setting: Slow
Overclocking: No, system will not even run stable at rated speeds.
Problem:
System just shuts itself down in the middle of gaming.
CPU temperature has a wide range, depending on how cool the night is and if I have my windows open etc the system can be as low as 40c. Under load while gaming I've seen it go to between 59c-62c.
I've gone into Core Center and turned off the dynamic overclocking so it doesn't adjust speed in the middle of playing games, thinking that might be causing issues.
I've also cranked the fans up all the way in Core Center to increase cooling.
Heck I've even turned Core Center OFF thinking it was messing with my system.
No antivirus is running in the background while I'm gaming. I've fresh installed XP Pro. I've re-applied service packs.
I'm worried about the temperature but I don't necessarily know for certain the sudden shutdowns are a cooling issue.
I am going on week FOUR of problems with this new system. I have never purchased an MSI mainboard and seriously, I have just flat out had it. I've already been through one RMA'd board, I am not RMAing another. I have 3 days left on my newegg account before I am stuck with this MSI, forever. If I can't find a solution ASAP (in 24 hours!) I am returning this MSI board and getting a Gigabyte 8KNXP.
Can anyone help me out here with suggestions please. I'm at my wits end. I've never had to do SO MUCH WORK to get a system running stable. I put my P3 with Intel mainboard together 2.5 years ago and I haven't had ONE single issue.
Stability is a BIG factor for me. I can't even think about overclocking when this sytem won't run at rated speeds!
Chris

This is a different problem.. the first board just flat out died after upgrading the BIOS. I never even got to use it.
This new board upgraded the BIOS just fine but I've been experiencing crashes and shutdowns.
I don't have any spare motherboard or CPU to test it in, and if I did I'd still have to run it for several days..and I don't have several days due in part to me having to dink around with it for so long.
I would say I am in game for 30-60 minutes before I see temperatures that high. Although again I have been playing this same game on my P3-1ghz with the same Video card and never once had a shutdown like this. Never once overheated.
I have all the fancy display/graphics options turned off..I have tested in different resolutions (it makes no difference temperature wise)
I do not know what my core temps are, I can check when I get home and post them if it helps.
I'm running everything at stock speeds. I've noticed Core Center ups my speed slowly from 201x4 to 203x4 etc and so I disabled that and finally flat out took Core Center out of startup. I didn't want it modifying anything while I was playing on the chance it was causing the crashes. Still no change even after that.
The temp does seem a bit high, but I have lapped the heatsink and fan and applied a layer of termal paste (silicon based) to both the HSF and the CPU. I removed that old black pad by scraping it off and then cleaning it with some xylene based carburetor cleaner. I spent several minutes rubbing the black melted parrafin goo off the processor and HSF with a coffee filter. I'm very confident there was little to none left when I applied the new thermal paste.
I don't understand why it runs so hot, nothing is overclocked, I'm running low settings in the game. These temps i'm posting are from Core Center. I have the case OPEN (plenty of ventilation) and I have the windows in my room open to the night air!! (i live in san diego, its cool at night right now) I tried with the case closed also just to be sure and I received the same temperature readings.
None of this makes sense...and after 4 weeks and 500 dollars I'm tired of having to make it sense. It should work right away and that's that.

Problem with (MSIE?) Acrobat 8.2.0. Uninstalling/installing

First of all:
Trying to uninstall and re-install Acrobat as it apparently got (messed up) when some fool installed Acrobat Reader 9.3 on the same computer, or at least, so I've been lead to believe. I had been trying to modify a security setting on a couple of PDF's and wasn't able to do it, then noticed that the occasional updates were not installing, so I was told (here and elsewhere) that I was going to continue experiencing problems as long as I had Reader AND Acroat installed.
I managed to uninstall Reader this AM but when trying to either uninstall OR repair Acrobat, I continually get the same message, to wit:
"Windows Installer
This patch package could not be opened. Verify that the patch package exists and that you can access it, or contact the application vendor to verify that this is a valid Windows installer patch package."
OK, so I go looking thru a LOT of KB articles and finally come to understand that the message refers to a WINDOWS (MSIE) installer problem, not a problem with Acrobat, per se. The recommended action was to use the MSIECUU (Clean Up Utility), except that THAT seems to have been deleted by Microsoft as being not the greatest thing to do to one's registry entries.
Sooooo....
I'm stumped, it's hot and I've been futzing with this chazzerai all day.
What do I do now? All I wanna do is change a few security settings, get Acrobat back to where it was, go home and have a martoonie.

Ah, the anti-virus... of course! I will do this next time I'm at the shop
(2 weeks).
Vince Brennan, Artisan
Frayed Knot Arts
416 West Woodlawn St
Philadelphia PA 19144
215-843-7207
http://www.frayedknotarts.com
Serving your knotting and fancywork needs worldwide..

Format problem with MSI 865Neo2-PFISR

I had a problem with my MSI 865Neo2-PFISR, when i was formatting the drive (WD 40GB 7200) format it was not responding... by thw way... i completed the format with the 4th try, and before 2 wks i have format again and everything it was fine. But why it was not responding at the first format?
i have Celeron 2.4Ghz northwood
MSI 865Neo2-PFISR
Kingston 256 DDR400
WD 40GB 7200rpm
Abit ATi 9200SE-DT 128MB
SoundBlaster AudigyES

I had the same PSU noname 350W and i formatted my disk fine, just 3 times it stops to respond at the first time, now i have levicom PSU with 28A on 3.3V and it's ok...

USB problem with msi (nforce 1)k7d420

Similar Messages

Maybe you are looking for