USB wifi adapter sometimes won't work properly after reboot [solved]
Sometimes it (WPN111) boots and everything is working. Other times I boot and it isn't working. Reloading ndiswrapper results in this error.
ndiswrapper (NdisWriteErrorLogEntry:190): log: C0001391, count: 4, return_address: f86d3e8c
ndiswrapper (NdisWriteErrorLogEntry:193): code: 0xf687fe00
ndiswrapper (NdisWriteErrorLogEntry:193): code: 0x1
ndiswrapper (NdisWriteErrorLogEntry:193): code: 0x0
ndiswrapper (NdisWriteErrorLogEntry:190): log: C0001391, count: 4, return_address: f86d3e8c
ndiswrapper (NdisWriteErrorLogEntry:193): code: 0xf687fe00
ndiswrapper (NdisWriteErrorLogEntry:193): code: 0x1
ndiswrapper (NdisWriteErrorLogEntry:193): code: 0x0
ndiswrapper (NdisWriteErrorLogEntry:193): code: 0x0
ndiswrapper (mp_init:219): couldn't initialize device: C0000001
ndiswrapper (pnp_start_device:435): Windows driver couldn't initialize the device (C0000001)
ndiswrapper (mp_halt:262): device f69fa440 is not initialized - not halting
ndiswrapper: device eth%d removed
ndiswrapper: probe of 1-6:1.0 failed with error -22
If it isn't working after boot it'll work only if I remove it, reload ndiswrapper, then plug it back in. Has anyone seen something like this before? Is there any way I can mess around w/ the order the uhci_hcd and ndiswrapper modules load?
Edit- Found the problem. Whenever linux restarts the device doesn't have the power cut and it won't reinitialize. If I shutdown, and then restart, the power is cut and it's fine.
Last edited by omgwtfbyobbq (2010-08-17 06:09:56)
Wonder if you have a conflict between two audio cards ... for example, I have a friend with some PulseAudio problems caused by conflict between the HDMI audio from his graphics card and his onboard sound. Something would switch PulseAudio to the wrong card and it would just quit after getting itself into a twist. Unsolved, I'm afraid, but have a look at commands such as:
aplay -l
pactl list sinks
pactl stat
(Latter two will need PulseAudio coaxed into life first)
and of course, the Arch wiki.
If there is a conflict, blacklisting kernel modules might also be needed.
Similar Messages
-
My USB external hard disk won't work anymore after I updated to 10.4.10
As I said in title since it's quite urgent to me. ALL of my files is in my external hard drive. It's format as FAT or FAT32 I can't remember since I use it between mac and PC. More than that IT IS WORKING FINE UNDER PC. Before updating to Mac 10.4.10 I used my hard disk fine till I updated to this version. I plug in my usb port and after a hours it still won't be detected. I can find my hard disk in finder or desktop. I have tried plug my hard disk to other MacBook or Mac Pro but still won't work anymore. However it's working fine under PC or when I started my MacBKPRO as WindowsXP under bootcamp, my hard disk is working fine, too.
I have search this forum and seems someone have got the same problem as I face. I don't know what to do...and I feel so disappointed to Mac.As Mac OS X has no known viruses in the wild, that leaves you with one of three possibilities.
1. When connected to the Windows machine, a virus has written over a critical boot block area which allows the drive to become crossplatform. Get the latest Windows virus detection software and make sure the drive is clean of Windows viruses.
2. The firmware that allows it to communicate driverless has become corrupted on the drive case. Replacing the drive case itself will eliminate that problem, as suggested earlier.
3. The directory damage is just enough that the boot block itself is damaged. Backup any critical data from the drive onto the Windows machine first, and run Alsoft Disk Warrior 4.0 to repair the directory and see if that works.
The fact that Mac OS X 10.3.9 won't read it basically eliminates this as a 10.4.10 problem. Only a boot block or firmware issue like this could make a drive not readable on one platform, but readable on another.
P.S. please note the nomenclature of Mac, versus MAC on this user tip, as it appears you haven't learned it:
http://discussions.apple.com/thread.jspa?threadID=503342&tstart=10 -
Mail.app won't work properly after installing Yosemite
My "new viewer window" in Mail.app won't work after installing Yosemite. I can not access the viewer window and thus none of my email.
How can I fix this?
Mail.app v 8.0some updates on this issue, Mail application uses the same proxy that has been set on your system (system preferences==>Network==>Advanced==>proxies). People usually use HTTP/HTTPS proxy for surfing the web. You should make sure to set SOCKS proxy as well. Mail application works with SOCKS proxy. Note that port number for SOCKS proxy is usually different from the port number for HTTP and HTTPS but the IP address of your server (apparently) is the same.
Hope this helps -
My appstore 'install' button won't work properly after being tapped. How do I fix this?
After I tap the button displaying the price, it moves to the right and becomes a small square/rectangle, then stutters and moves to the lft, become green and saying 'Insta...'. Assuming this is the Install button, I press it, but it just becomes blue again. No matter how many times I try, it doesn't install. Anyway to fix it that doesn't involve restoring or deleting any of my previously downloaded apps?
Disclaimer - For me the Apple Support Communities are an international user to user technical support forum. As a man from Mexico my first language is Spanish. I do not speak English, however I do write in English with the aid of the Mac OS X spelling and grammar checks. I also live in a culture very different from that found in most 1st world nations, such as that in the two dominant North American countries. Written language has no tone. When offering advice in the ASC, my comments are not meant to be anything more than helpful and certainly not to be taken as insults.
Try a reset. Press & hold the Power and Home buttons simultaneously, ignoring the red power off slider, until the Apple logo appears. Then release both buttons. This should not affect any content on the iPad, it is similar to rebooting your computer. -
Is there such a thing as a USB WIFI adapter that works with OS X 10.9?
Is there such a thing as a USB WIFI adapter that works with OS X 10.9? I have tried 3 different models, none of which were compatible. The built-in WIFI card in a 2012 Mac Pro is absolutely crap (0/10 on the performance scale). Any recommendations?
Hey everyone, yes I have installed the drivers properly. I've used an ASUS, Bolse, and EDIMAX adapter. Some had a 10.8 driver, some had 10.9. After reaching out to customer support for each and every one of these companies for help, and through multiple returns, I have not gotten anywhere with any of the drivers or products.
It's getting ridiculously hard to stay an Apple customer when the quality of their products are getting worse and worse, which leaves me no choice but to go to third parties to replace the faulty hardware.
And honestly I'm just sick of calling India every day to get my issues resolved. -
USB wifi adapter can only handle one request or socket at a time
I have a usb wifi adapter that I bought recently. The strange thing is that if I'm doing only one thing that is using the network (e.g. downloading a file) it works good and fast. But say I'm downloading a file and I do ANYTHING else that uses the network (e.g. just opening a browser at google.ca), the download comes to a stop. Then if I close the browser, the download starts up again a couple seconds later, good and fast.
Another example is, say I'm in a Google Hangouts (video chat) session. As long as that is the only thing I have running, the chat works fine. If I open a second browser window, then the chat gets super choppy and pretty much un-usable until I close the second window.
So basically it seems like I can have only one open socket at a time, or else it can handle only one request at a time. Also, most webpages open very slowly as a result because the browser only seems to be able to download one static file at a time (e.g. js and css files needed by the page).
I'm sure it's a problem with the usb wifi adapter because I didn't have these problems when I was on a wired connection, and I have other devices using wifi (e.g. laptops and tablets) that don't have this problem either.
Rather than paste a bunch of output from commands, please kindly tell me what to run in order to gather any useful info.
Thanks,
Edit: The adapter is an ASUS USB n-53 (N600).
Last edited by Pacopag (2014-07-18 14:36:20)I was exploring the CD that came with the device. Turns out there are Linux drivers on it. I didn't install any drivers, as wicd detected it automatically. I'm wondering if changing drivers might help. Can someone help me interpret the installation instructions?
Here are the instructions
* README
* Ralink Tech Inc.
* http://www.ralinktech.com
=======================================================================
ModelName:
===========
RT3572 Wireless Lan Linux Driver
=======================================================================
Driver lName:
===========
rt3572sta.o/rt3572sta.ko
=======================================================================
Supporting Kernel:
===================
linux kernel 2.4 and 2.6 series.
Tested in Redhat 7.3 or later.
=======================================================================
Ralink Hardware:
===================
Ralink 802.11n Wireless LAN Card.
=======================================================================
Description:
=============
This is a linux device driver for Ralink RT2870 USB ABGN WLAN Card.
=======================================================================
Contents:
=============
Makefile : Makefile
*.c : c files
*.h : header files
=======================================================================
Features:
==========
This driver implements basic IEEE802.11. Infrastructure and adhoc mode with
open or shared or WPA-PSK or WPA2-PSK authentication method.
NONE, WEP, TKIP and AES encryption.
=======================================================================
Build Instructions:
====================
1> tar -jxvf 2011_1003_RT3572_Linux_STA_v2.5.0.0.DPO.tar.bz2
go to "./2011_1003_RT3572_Linux_STA_v2.5.0.0.DPO" directory.
2> switch to super user.
** for Fedora
$su
** for Ubuntu
$sudo su
3> in Makefile
set the "MODE = STA" in Makefile and chose the TARGET to Linux by set "TARGET = LINUX"
define the linux kernel source include file path LINUX_SRC
modify to meet your need.
4> in os/linux/config.mk
define the GCC and LD of the target machine
define the compiler flags CFLAGS
modify to meet your need.
** Build for being controlled by NetworkManager or wpa_supplicant wext functions
Please set 'HAS_WPA_SUPPLICANT=y' and 'HAS_NATIVE_WPA_SUPPLICANT_SUPPORT=y'.
=> #>cd wpa_supplicant-x.x
=> #>./wpa_supplicant -Dwext -ira0 -c wpa_supplicant.conf -d
** Build for being controlled by WpaSupplicant with Ralink Driver
Please set 'HAS_WPA_SUPPLICANT=y' and 'HAS_NATIVE_WPA_SUPPLICANT_SUPPORT=n'.
=> #>cd wpa_supplicant-0.5.7
=> #>./wpa_supplicant -Dralink -ira0 -c wpa_supplicant.conf -d
5> compile driver source code
$make
=======================================================================
Install Instructions:
================================
1> load driver
$make install
2> plug in USB dongle.
=======================================================================
Note:
================================
Under Fedora 15 or 16, after you install the driver, if there is "firmware missing" issue occurs, please follow the following steps:
1> remove driver
$rmmod rt2800usb
$rmmod rt2800lib
$rmmod rt2x00usb
$rmmod rt2x00lib
2> enter /etc/modprobe.d and edit blacklist.conf. Add one line (ususally add it in the buttom of the file):
blacklist rt2800usb
3> reboot system
$reboot
=======================================================================
Uninstall Instructions:
================================
1> go to "./2011_1003_RT3572_Linux_STA_v2.5.0.0.DPO" directory.
2> switch to super user.
$sudo su
3> unload driver
$make uninstall
4> reboot system
$reboot
=======================================================================
CONFIGURATION:
====================
RT2870 driver can be configured via following interfaces,
i.e. (i)"iwconfig" command, (ii)"iwpriv" command, (iii) configuration file
i) iwconfig comes with kernel.
ii) iwpriv usage, please refer to file "iwpriv_usage.txt" for details.
iii)modify configuration file "RT2870STA.dat" in /etc/Wireless/RT2870STA/RT2870STA.dat.
Configuration File : RT2870STA.dat
# Copy this file to /etc/Wireless/RT2870STA/RT2870STA.dat
# This file is a binary file and will be read on loading rt.o module.
# Use "vi RT2870STA.dat" to modify settings according to your need.
# 1.) set NetworkType to "Adhoc" for using Adhoc-mode, otherwise using Infrastructure
# 2.) set Channel to "0" for auto-select on Infrastructure mode
# 3.) set SSID for connecting to your Accss-point.
# 4.) AuthMode can be "WEPAUTO", "OPEN", "SHARED", "WPAPSK", "WPA2PSK", "WPANONE"
# 5.) EncrypType can be "NONE", "WEP", "TKIP", "AES"
# for more information refer to the Readme file.
#The word of "Default" must not be removed
Default
CountryRegion=5
CountryRegionABand=7
CountryCode=
SSID=Dennis2860AP
NetworkType=Infra
WirelessMode=9
Channel=0
BeaconPeriod=100
TxPower=100
BGProtection=0
TxPreamble=0
RTSThreshold=2347
FragThreshold=2346
TxBurst=1
WmmCapable=0
AckPolicy=0;0;0;0
AuthMode=OPEN
EncrypType=NONE
WPAPSK=
DefaultKeyID=1
Key1Type=0
Key1Str=
Key2Type=0
Key2Str=
Key3Type=0
Key3Str=
Key4Type=0
Key4Str=
PSMode=CAM
FastRoaming=0
RoamThreshold=70
HT_RDG=1
HT_EXTCHA=0
HT_OpMode=1
HT_MpduDensity=4
HT_BW=1
HT_AutoBA=1
HT_BADecline=0
HT_AMSDU=0
HT_BAWinSize=64
HT_GI=1
HT_MCS=33
HT_MIMOPSMode=3
IEEE80211H=0
TGnWifiTest=0
WirelessEvent=0
CarrierDetect=0
*NOTE:
WMM parameters
WmmCapable Set it as 1 to turn on WMM Qos support
AckPolicy1~4 Ack policy which support normal Ack or no Ack
(AC_BK, AC_BE, AC_VI, AC_VO)
All WMM parameters do not support iwpriv command but ¡¥WmmCapable¡¦¡¦,
please store all parameter to RT2870STA.dat, and restart driver.
syntax is 'Param'='Value' and describes below.
@> CountryRegion=value
value
0: use 1 ~ 11 Channel
1: use 1 ~ 13 Channel
2: use 10 ~ 11 Channel
3: use 10 ~ 13 Channel
4: use 14 Channel
5: use 1 ~ 14 Channel
6: use 3 ~ 9 Channel
7: use 5 ~ 13 Channel
31: use 1 ~ 14 Channel (ch1-11:active scan, ch12-14 passive scan)
@> CountryRegionABand=value
value
0: use 36, 40, 44, 48, 52, 56, 60, 64, 149, 153, 157, 161, 165 Channel
1: use 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140 Channel
2: use 36, 40, 44, 48, 52, 56, 60, 64 Channel
3: use 52, 56, 60, 64, 149, 153, 157, 161 Channel
4: use 149, 153, 157, 161, 165 Channel
5: use 149, 153, 157, 161 Channel
6: use 36, 40, 44, 48 Channel
7: use 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 165 Channel
8: use 52, 56, 60, 64 Channel
9: use 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 132, 136, 140, 149, 153, 157, 161, 165 Channel
10: use 36, 40, 44, 48, 149, 153, 157, 161, 165 Channel
11: use 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 149, 153, 157, 161 Channel
@> CountryCode=value
value
AG, AR, AW, AU, AT, BS, BB, BM, BR, BE, BG, CA, KY, CL, CN, CO, CR, CY, CZ, DK, DO, EC, SV, FI, FR, DE,
GR, GU, GT, HT, HN, HK, HU, IS, IN, ID, IE, IL, IT, JP, JO, LV, LI, LT, LU, MY, MT, MA, MX, NL, NZ, NO,
PE, PT, PL, RO, RU, SA, CS, SG, SK, SI, ZA, KR, ES, SE, CH, TW, TR, GB, UA, AE, US, VE
"" => using default setting: 2.4 G - ch 1~11; 5G - ch 52~64, 100~140, 149~165
@> SSID=value
value
0~z, 1~32 ascii characters.
@> WirelessMode=value
value
0: legacy 11b/g mixed
1: legacy 11B only
2: legacy 11A only //Not support in RfIcType=1(id=RFIC_5225) and RfIcType=2(id=RFIC_5325)
3: legacy 11a/b/g mixed //Not support in RfIcType=1(id=RFIC_5225) and RfIcType=2(id=RFIC_5325)
4: legacy 11G only
5: 11ABGN mixed
6: 11N only
7: 11GN mixed
8: 11AN mixed
9: 11BGN mixed
10: 11AGN mixed
@> Channel=value
value
depends on CountryRegion or CountryRegionABand
@> BGProtection=value
value
0: Auto
1: Always on
2: Always off
@> TxPreamble=value
value
0:Preamble Long
1:Preamble Short
2:Auto
@> RTSThreshold=value
value
1~2347
@> FragThreshold=value
value
256~2346
@> TxBurst=value
value
0: Disable
1: Enable
@> NetworkType=value
value
Infra: infrastructure mode
Adhoc: adhoc mode
@> AuthMode=value
value
OPEN For open system
SHARED For shared key system
WEPAUTO Auto switch between OPEN and SHARED
WPAPSK For WPA pre-shared key (Infra)
WPA2PSK For WPA2 pre-shared key (Infra)
WPANONE For WPA pre-shared key (Adhoc)
WPA Use WPA-Supplicant
WPA2 Use WPA-Supplicant
@> EncrypType=value
value
NONE For AuthMode=OPEN
WEP For AuthMode=OPEN or AuthMode=SHARED
TKIP For AuthMode=WPAPSK or WPA2PSK
AES For AuthMode=WPAPSK or WPA2PSK
@> DefaultKeyID=value
value
1~4
@> Key1=value
Key2=value
Key3=value
Key4=value
value
10 or 26 hexadecimal characters eg: 012345678
5 or 13 ascii characters eg: passd
(usage : "iwpriv" only)
@> Key1Type=vaule
Key2Type=value
Key3Type=vaule
Key4Type=vaule
value
0 hexadecimal type
1 assic type
(usage : reading profile only)
@> Key1Str=value
Key2Str=value
Key3Str=vaule
Key4Str=vaule
value
10 or 26 characters (key type=0)
5 or 13 characters (key type=1)
(usage : reading profile only)
@> WPAPSK=value
value
8~63 ASCII or
64 HEX characters
@> WmmCapable=value
value
0: Disable WMM
1: Enable WMM
@> PSMode=value
value
CAM Constantly Awake Mode
Max_PSP Max Power Savings
Fast_PSP Power Save Mode
@> FastRoaming=value
value
0 Disabled
1 Enabled
@> RoamThreshold=value
value
Positive Interger(dBm)
@> HT_RDG=value
value
0 Disabled
1 Enabled
@> HT_EXTCHA=value (Extended Channel Switch Announcement)
value
0 Below
1 Above
@> HT_OpMode=value
value
0 HT mixed format
1 HT greenfield format
@> HT_MpduDensity=value
value (based on 802.11n D2.0)
0: no restriction
1: 1/4 £gs
2: 1/2 £gs
3: 1 £gs
4: 2 £gs
5: 4 £gs
6: 8 £gs
7: 16 £gs
@> HT_BW=value
value
0 20MHz
1 40MHz
@> HT_AutoBA=value
value
0 Disabled
1 Enabled
@> HT_BADecline
value
0 Disabled
1 Enabled <Reject BA request from AP>
@> HT_AMSDU=value
value
0 Disabled
1 Enabled
@> HT_BAWinSize=value
value
1 ~ 64
@> HT_GI=value
value
0 long GI
1 short GI
@> HT_MCS=value
value
0 ~ 15
33: auto
@> HT_MIMOPSMode=value
value (based on 802.11n D2.0)
0 Static SM Power Save Mode
1 Dynamic SM Power Save Mode
2 Reserved
3 SM enabled
(not fully support yet)
@> IEEE80211H=value
value
0 Disabled
1 Enabled
@> TGnWifiTest=value
value
0 Disabled
1 Enabled
@> WirelessEvent=value
value
0 Disabled
1 Enabled <send custom wireless event>
@> CarrierDetect=value
value
0 Disabled
1 Enabled
MORE INFORMATION
=================================================================================
If you want for rt2870 driver to auto-load at boot time:
A) choose ra0 for first RT2870 WLAN card, ra1 for second RT2870 WLAN card, etc.
B) create(edit) 'ifcfg-ra0' file in /etc/sysconfig/network-scripts/,
edit( or add the line) in /etc/modules.conf:
alias ra0 rt2870sta
C) edit(create) the file /etc/sysconfig/network-scripts/ifcfg-ra0
DEVICE='ra0'
ONBOOT='yes'
NOTE:
if you use dhcp, add this line too .
BOOTPROTO='dhcp'
*D) To ease the Default Gateway setting,
add the line
GATEWAY=x.x.x.x
in /etc/sysconfig/network
Here is the Makefile
RT28xx_MODE = STA
TARGET = LINUX
CHIPSET = 3572
OSABL = NO
#RT28xx_DIR = home directory of RT28xx source code
RT28xx_DIR = $(shell pwd)
RTMP_SRC_DIR = $(RT28xx_DIR)/RT$(CHIPSET)
#PLATFORM: Target platform
PLATFORM = PC
#PLATFORM = 5VT
#PLATFORM = IKANOS_V160
#PLATFORM = IKANOS_V180
#PLATFORM = SIGMA
#PLATFORM = SIGMA_8622
#PLATFORM = STAR
#PLATFORM = IXP
#PLATFORM = INF_TWINPASS
#PLATFORM = INF_DANUBE
#PLATFORM = INF_AR9
#PLATFORM = INF_VR9
#PLATFORM = BRCM_6358
#PLATFORM = INF_AMAZON_SE
#PLATFORM = CAVM_OCTEON
#PLATFORM = CMPC
#PLATFORM = RALINK_2880
#PLATFORM = RALINK_3052
#PLATFORM = SMDK
#PLATFORM = RMI
#PLATFORM = RMI_64
#PLATFORM = KODAK_DC
#PLATFORM = DM6446
#PLATFORM = FREESCALE8377
#PLATFORM = BL2348
#PLATFORM = BLUBB
#PLATFORM = BLPMP
#PLATFORM = MT85XX
#PLATFORM = NXP_TV550
#PLATFORM = MVL5
ifeq ($(TARGET),LINUX)
MAKE = make
endif
ifeq ($(PLATFORM),5VT)
LINUX_SRC = /home/ralink-2860-sdk-5vt-distribution/linux-2.6.17
CROSS_COMPILE = /opt/crosstool/uClibc_v5te_le_gcc_4_1_1/bin/arm-linux-
endif
ifeq ($(PLATFORM),IKANOS_V160)
LINUX_SRC = /home/sample/projects/LX_2618_RG_5_3_00r4_SRC/linux-2.6.18
CROSS_COMPILE = mips-linux-
endif
ifeq ($(PLATFORM),IKANOS_V180)
LINUX_SRC = /home/sample/projects/LX_BSP_VX180_5_4_0r1_ALPHA_26DEC07/linux-2.6.18
CROSS_COMPILE = mips-linux-
endif
ifeq ($(PLATFORM),SIGMA)
LINUX_SRC = /root/sigma/smp86xx_kernel_source_2.7.172.0/linux-2.6.15
CROSS_COMPILE = /root/sigma/smp86xx_toolchain_2.7.172.0/build_mipsel_nofpu/staging_dir/bin/mipsel-linux-
endif
ifeq ($(PLATFORM),SIGMA_8622)
LINUX_SRC = /home/snowpin/armutils_2.5.120.1/build_arm/linux-2.4.22-em86xx
CROSS_COMPILE = /home/snowpin/armutils_2.5.120.1/toolchain/bin/arm-elf-
CROSS_COMPILE_INCLUDE = /home/snowpin/armutils_2.5.120.1/toolchain/lib/gcc-lib/arm-elf/2.95.3
endif
ifeq ($(PLATFORM),STAR)
LINUX_SRC = /opt/star/kernel/linux-2.4.27-star
CROSS_COMPILE = /opt/star/tools/arm-linux/bin/arm-linux-
endif
ifeq ($(PLATFORM),RMI)
LINUX_SRC = /opt/rmi/1.7.0/linux/src/
CROSS_COMPILE = /opt/rmi/1.7.0/mipscross/nptl/bin/mips64-unknown-linux-gnu-
endif
ifeq ($(PLATFORM),RMI_64)
LINUX_SRC = /opt/rmi/1.7.0/linux_64/src/
CROSS_COMPILE = /opt/rmi/1.7.0/mipscross/nptl/bin/mips64-unknown-linux-gnu-
endif
ifeq ($(PLATFORM), RALINK_2880)
LINUX_SRC = /project/stable/RT288x/RT288x_SDK/source/linux-2.4.x
CROSS_COMPILE = /opt/buildroot-gdb/bin/mipsel-linux-
endif
ifeq ($(PLATFORM),RALINK_3052)
LINUX_SRC = /home/peter/ap_soc/SDK_3_3_0_0/RT288x_SDK/source/linux-2.6.21.x
CROSS_COMPILE = /opt/buildroot-gcc342/bin/mipsel-linux-uclibc-
endif
ifeq ($(PLATFORM),FREESCALE8377)
LINUX_SRC = /opt/ltib-mpc8377_rds-20090309/rpm/BUILD/linux-2.6.25
CROSS_COMPILE = /opt/freescale/usr/local/gcc-4.2.187-eglibc-2.5.187/powerpc-linux-gnu/bin/powerpc-linux-gnu-
endif
ifeq ($(PLATFORM),BL2348)
LINUX_SRC = /home/sample/Customers/BroadLight/bl234x-linux-2.6.21-small-v29
CROSS_COMPILE = mips-wrs-linux-gnu-
endif
ifeq ($(PLATFORM),BLUBB)
LINUX_SRC = /home/sample/Customers/BroadLight/UBB/gmp20/linux-2.6.21-small
CROSS_COMPILE = mips-wrs-linux-gnu-
endif
ifeq ($(PLATFORM),BLPMP)
LINUX_SRC = /home/sample/Customers/BroadLight/UBB/pmp16/bl234x-linux-2.6.21-small-v30.2
CROSS_COMPILE = mips-wrs-linux-gnu-
endif
ifeq ($(PLATFORM),PC)
# Linux 2.6
LINUX_SRC = /lib/modules/$(shell uname -r)/build
# Linux 2.4 Change to your local setting
#LINUX_SRC = /usr/src/linux-2.4
LINUX_SRC_MODULE = /lib/modules/$(shell uname -r)/kernel/drivers/net/wireless/
CROSS_COMPILE =
endif
ifeq ($(PLATFORM),IXP)
LINUX_SRC = /project/stable/Gmtek/snapgear-uclibc/linux-2.6.x
CROSS_COMPILE = arm-linux-
endif
ifeq ($(PLATFORM),INF_TWINPASS)
# Linux 2.6
#LINUX_SRC = /lib/modules/$(shell uname -r)/build
# Linux 2.4 Change to your local setting
LINUX_SRC = /project/stable/twinpass/release/2.0.1/source/kernel/opensource/linux-2.4.31/
CROSS_COMPILE = mips-linux-
endif
ifeq ($(PLATFORM),INF_DANUBE)
LINUX_SRC = /opt/danube/sdk/linux-2.6.16.x
CROSS_COMPILE = mips-linux-
ROOTDIR = /opt/danube/sdk
export ROOTDIR
endif
ifeq ($(PLATFORM),INF_AR9)
LINUX_SRC = /root/ar9/xR9_BSP1.2.2.0/source/kernel/opensource/linux-2.6.20/
CROSS_COMPILE = /root/ar9/ifx-lxdb26-1.0.2/gcc-3.4.4/toolchain-mips/bin/
endif
ifeq ($(PLATFORM),INF_VR9)
LINUX_SRC = /home/public/lantiq/VR9/UGW-4.2/build_dir/linux-ifxcpe_platform_vr9/linux-2.6.20.19
CROSS_COMPILE = /home/public/lantiq/VR9/UGW-4.2/staging_dir/toolchain-mips_gcc-3.4.6_uClibc-0.9.29/bin/mips-linux-
endif
ifeq ($(PLATFORM),BRCM_6358)
LINUX_SRC =
CROSS_COMPILE =
endif
ifeq ($(PLATFORM),INF_AMAZON_SE)
# Linux 2.6
#LINUX_SRC = /lib/modules/$(shell uname -r)/build
# Linux 2.4 Change to your local setting
LINUX_SRC = /backup/ifx/3.6.2.2/source/kernel/opensource/linux-2.4.31
#CROSS_COMPILE = mips-linux-
#LINUX_SRC = /project/Infineon/3.6.2.2/source/kernel/opensource/linux-2.4.31
CROSS_COMPILE = /opt/uclibc-toolchain/ifx-lxdb-1-2-3-external/gcc-3.3.6/toolchain-mips/R0208V35/mips-linux-uclibc/bin/
endif
ifeq ($(PLATFORM),ST)
LINUX_SRC = /opt/STM/STLinux-2.2/devkit/sources/kernel/linux0039
CROSS_COMPILE = /opt/STM/STLinux-2.2/devkit/sh4/bin/sh4-linux-
ARCH := sh
export ARCH
endif
ifeq ($(PLATFORM),CAVM_OCTEON)
OCTEON_ROOT = /usr/local/Cavium_Networks/OCTEON-SDK
LINUX_SRC = $(OCTEON_ROOT)/linux/kernel_2.6/linux
CROSS_COMPILE = mips64-octeon-linux-gnu-
endif
ifeq ($(PLATFORM),CMPC)
LINUX_SRC = /opt/fvt_11N_SDK_0807/fvt131x_SDK_11n/linux-2.6.17
CROSS_COMPILE =
endif
ifeq ($(PLATFORM),SMDK)
LINUX_SRC = /home/bhushan/itcenter/may28/linux-2.6-samsung
CROSS_COMPILE = /usr/local/arm/4.2.2-eabi/usr/bin/arm-linux-
endif
ifeq ($(PLATFORM),KODAK_DC)
SKD_SRC = C:/SigmaTel/DC1250_SDK_v1-9/sdk
CROSS_COMPILE = $(cc)
endif
ifeq ($(PLATFORM),DM6446)
LINUX_SRC = /home/fonchi/work/soc/ti-davinci
endif
ifeq ($(PLATFORM),MT85XX)
LINUX_SRC = /home/john/MTK/BDP_Linux/linux-2.6.27
CROSS_COMPILE = armv6z-mediatek-linux-gnueabi-
endif
ifeq ($(PLATFORM),NXP_TV550)
LINUX_SRC = /data/tv550/kernel/linux-2.6.28.9
LINUX_SRC_MODULE = /data/tv550/kernel/linux-2.6.28.9/drivers/net/wireless
CROSS_COMPILE = /opt/embeddedalley/nxp_tv550/bin/mipsel-linux-
endif
ifeq ($(PLATFORM),MVL5)
LINUX_SRC = /home2/charlestu/AP-VT3426/linux-2.6.18
CROSS_COMPILE = /opt/montavista/pro/devkit/arm/v5t_le_mvl5/bin/arm_v5t_le-
endif
export OSABL RT28xx_DIR RT28xx_MODE LINUX_SRC CROSS_COMPILE CROSS_COMPILE_INCLUDE PLATFORM RELEASE CHIPSET RTMP_SRC_DIR LINUX_SRC_MODULE TARGET
# The targets that may be used.
PHONY += all build_tools test UCOS THREADX LINUX release prerelease clean uninstall install libwapi osabl
all: build_tools $(TARGET)
build_tools:
$(MAKE) -C tools
$(RT28xx_DIR)/tools/bin2h
test:
$(MAKE) -C tools test
LINUX:
ifneq (,$(findstring 2.4,$(LINUX_SRC)))
cp -f os/linux/Makefile.4 $(RT28xx_DIR)/os/linux/Makefile
$(MAKE) -C $(RT28xx_DIR)/os/linux/
cp -f $(RT28xx_DIR)/os/linux/rt$(CHIPSET)sta.o /tftpboot
else
cp -f os/linux/Makefile.6 $(RT28xx_DIR)/os/linux/Makefile
ifeq ($(PLATFORM),DM6446)
$(MAKE) ARCH=arm CROSS_COMPILE=arm_v5t_le- -C $(LINUX_SRC) SUBDIRS=$(RT28xx_DIR)/os/linux modules
else
ifeq ($(PLATFORM),FREESCALE8377)
$(MAKE) ARCH=powerpc CROSS_COMPILE=$(CROSS_COMPILE) -C $(LINUX_SRC) SUBDIRS=$(RT28xx_DIR)/os/linux modules
else
$(MAKE) -C $(LINUX_SRC) SUBDIRS=$(RT28xx_DIR)/os/linux modules
endif
endif
endif
clean:
ifeq ($(TARGET), LINUX)
cp -f os/linux/Makefile.clean os/linux/Makefile
$(MAKE) -C os/linux clean
rm -rf os/linux/Makefile
endif
uninstall:
ifeq ($(TARGET), LINUX)
ifneq (,$(findstring 2.4,$(LINUX_SRC)))
$(MAKE) -C $(RT28xx_DIR)/os/linux -f Makefile.4 uninstall
else
$(MAKE) -C $(RT28xx_DIR)/os/linux -f Makefile.6 uninstall
endif
endif
install:
ifeq ($(TARGET), LINUX)
ifneq (,$(findstring 2.4,$(LINUX_SRC)))
$(MAKE) -C $(RT28xx_DIR)/os/linux -f Makefile.4 install
else
$(MAKE) -C $(RT28xx_DIR)/os/linux -f Makefile.6 install
endif
endif
# Declare the contents of the .PHONY variable as phony. We keep that information in a variable
.PHONY: $(PHONY)
Here is the config.mk
# Support ATE function
HAS_ATE=n
# Support ATE NEW TXCONT solution
HAS_NEW_TXCONT=n
# Support QA ATE function
HAS_QA_SUPPORT=n
# Support XLINK mode
HAS_XLINK=n
# Support Wpa_Supplicant
HAS_WPA_SUPPLICANT=y
# Support Native WpaSupplicant for Network Maganger
HAS_NATIVE_WPA_SUPPLICANT_SUPPORT=y
#Support Net interface block while Tx-Sw queue full
HAS_BLOCK_NET_IF=n
#Support DFS function
HAS_DFS_SUPPORT=n
#Support Carrier-Sense function
HAS_CS_SUPPORT=n
# Support for Multiple Cards
HAS_MC_SUPPORT=n
#Support for IEEE802.11e DLS
HAS_QOS_DLS_SUPPORT=n
#Support for EXT_CHANNEL
HAS_EXT_BUILD_CHANNEL_LIST=n
#Support for Net-SNMP
HAS_SNMP_SUPPORT=n
#Support features of 802.11n Draft3
HAS_DOT11N_DRAFT3_SUPPORT=y
#Support features of Single SKU.
HAS_SINGLE_SKU_SUPPORT=n
#Support features of 802.11n
HAS_DOT11_N_SUPPORT=y
HAS_KTHREAD_SUPPORT=n
#Support statistics count
HAS_STATS_COUNT=y
#Support USB_BULK_BUF_ALIGMENT
HAS_USB_BULK_BUF_ALIGMENT=n
#Support for USB_SUPPORT_SELECTIVE_SUSPEND
HAS_USB_SUPPORT_SELECTIVE_SUSPEND=n
#Client support WDS function
HAS_CLIENT_WDS_SUPPORT=n
#Support for Bridge Fast Path & Bridge Fast Path function open to other module
HAS_BGFP_SUPPORT=n
HAS_BGFP_OPEN_SUPPORT=n
#Support MAC80211 LINUX-only function
HAS_CFG80211_SUPPORT=n
#Support RFKILL hardware block/unblock LINUX-only function
HAS_RFKILL_HW_SUPPORT=n
HAS_RESOURCE_PRE_ALLOC=y
HAS_LED_CONTROL_SUPPORT=y
CC := $(CROSS_COMPILE)gcc
LD := $(CROSS_COMPILE)ld
WFLAGS := -DAGGREGATION_SUPPORT -DPIGGYBACK_SUPPORT -DWMM_SUPPORT -DLINUX -Wall -Wstrict-prototypes -Wno-trigraphs
WFLAGS += -DSYSTEM_LOG_SUPPORT -DRT28xx_MODE=$(RT28xx_MODE) -DCHIPSET=$(CHIPSET)
ifeq ($(HAS_RESOURCE_PRE_ALLOC),y)
WFLAGS += -DRESOURCE_PRE_ALLOC
endif
ifeq ($(HAS_KTHREAD_SUPPORT),y)
WFLAGS += -DKTHREAD_SUPPORT
endif
# config for STA mode
ifeq ($(RT28xx_MODE),STA)
WFLAGS += -DCONFIG_STA_SUPPORT -DDBG
ifeq ($(HAS_XLINK),y)
WFLAGS += -DXLINK_SUPPORT
endif
ifeq ($(HAS_WPA_SUPPLICANT),y)
WFLAGS += -DWPA_SUPPLICANT_SUPPORT
ifeq ($(HAS_NATIVE_WPA_SUPPLICANT_SUPPORT),y)
WFLAGS += -DNATIVE_WPA_SUPPLICANT_SUPPORT -DCREDENTIAL_STORE -DPROFILE_STORE
endif
endif
ifeq ($(HAS_ATE),y)
WFLAGS += -DRALINK_ATE
WFLAGS += -DCONFIG_RT2880_ATE_CMD_NEW
ifeq ($(HAS_NEW_TXCONT),y)
WFLAGS += -DNEW_TXCONT
endif
ifeq ($(HAS_QA_SUPPORT),y)
WFLAGS += -DRALINK_QA
endif
endif
ifeq ($(HAS_SNMP_SUPPORT),y)
WFLAGS += -DSNMP_SUPPORT
endif
ifeq ($(HAS_QOS_DLS_SUPPORT),y)
WFLAGS += -DQOS_DLS_SUPPORT
endif
ifeq ($(HAS_DOT11_N_SUPPORT),y)
WFLAGS += -DDOT11_N_SUPPORT
ifeq ($(HAS_DOT11N_DRAFT3_SUPPORT),y)
WFLAGS += -DDOT11N_DRAFT3
endif
endif
ifeq ($(HAS_CS_SUPPORT),y)
WFLAGS += -DCARRIER_DETECTION_SUPPORT
endif
ifeq ($(HAS_STATS_COUNT),y)
WFLAGS += -DSTATS_COUNT_SUPPORT
endif
ifeq ($(HAS_USB_SUPPORT_SELECTIVE_SUSPEND),y)
WFLAGS += -DUSB_SUPPORT_SELECTIVE_SUSPEND -DCONFIG_PM
endif
ifeq ($(HAS_CFG80211_SUPPORT),y)
WFLAGS += -DRT_CFG80211_SUPPORT
ifeq ($(HAS_RFKILL_HW_SUPPORT),y)
WFLAGS += -DRFKILL_HW_SUPPORT
endif
endif
endif
# endif of ifeq ($(RT28xx_MODE),STA)
# Common compiler flag
ifeq ($(HAS_EXT_BUILD_CHANNEL_LIST),y)
WFLAGS += -DEXT_BUILD_CHANNEL_LIST
endif
ifeq ($(HAS_IDS_SUPPORT),y)
WFLAGS += -DIDS_SUPPORT
endif
ifeq ($(OSABL),YES)
WFLAGS += -DEXPORT_SYMTAB
endif
ifeq ($(HAS_CLIENT_WDS_SUPPORT),y)
WFLAGS += -DCLIENT_WDS
endif
ifeq ($(HAS_BGFP_SUPPORT),y)
WFLAGS += -DBG_FT_SUPPORT
endif
ifeq ($(HAS_BGFP_OPEN_SUPPORT),y)
WFLAGS += -DBG_FT_OPEN_SUPPORT
endif
ifeq ($(HAS_LED_CONTROL_SUPPORT),y)
WFLAGS += -DLED_CONTROL_SUPPORT
endif
# ChipSet specific definitions.
ifeq ($(CHIPSET),2870)
WFLAGS +=-DRTMP_MAC_USB -DRTMP_USB_SUPPORT -DRT2870 -DRT28xx -DRTMP_TIMER_TASK_SUPPORT -DA_BAND_SUPPORT
CHIPSET_DAT = 2870
ifeq ($(HAS_DFS_SUPPORT),y)
WFLAGS += -DDFS_SOFTWARE_SUPPORT
endif
endif
ifeq ($(CHIPSET),3572)
WFLAGS +=-DRTMP_MAC_USB -DRTMP_USB_SUPPORT -DRT2870 -DRT28xx -DRT30xx -DRT35xx -DRTMP_TIMER_TASK_SUPPORT -DRTMP_RF_RW_SUPPORT -DRTMP_EFUSE_SUPPORT -DA_BAND_SUPPORT -DSPECIFIC_VCORECAL_SUPPORT
CHIPSET_DAT = 2870
ifeq ($(HAS_DFS_SUPPORT),y)
WFLAGS += -DDFS_SOFTWARE_SUPPORT
endif
endif
ifeq ($(PLATFORM),5VT)
#WFLAGS += -DCONFIG_5VT_ENHANCE
endif
ifeq ($(HAS_BLOCK_NET_IF),y)
WFLAGS += -DBLOCK_NET_IF
endif
ifeq ($(HAS_DFS_SUPPORT),y)
WFLAGS += -DDFS_SUPPORT
endif
ifeq ($(HAS_MC_SUPPORT),y)
WFLAGS += -DMULTIPLE_CARD_SUPPORT
endif
ifeq ($(PLATFORM),RMI)
WFLAGS += -DRT_BIG_ENDIAN
endif
ifeq ($(PLATFORM),BL2348)
WFLAGS += -DRT_BIG_ENDIAN
endif
ifeq ($(PLATFORM),BLUBB)
WFLAGS += -DRT_BIG_ENDIAN
endif
ifeq ($(PLATFORM),BLPMP)
WFLAGS += -DRT_BIG_ENDIAN
endif
ifeq ($(PLATFORM),RMI_64)
WFLAGS += -DRT_BIG_ENDIAN
endif
ifeq ($(PLATFORM),IXP)
WFLAGS += -DRT_BIG_ENDIAN
endif
ifeq ($(PLATFORM),IKANOS_V160)
WFLAGS += -DRT_BIG_ENDIAN -DIKANOS_VX_1X0
endif
ifeq ($(PLATFORM),IKANOS_V180)
WFLAGS += -DRT_BIG_ENDIAN -DIKANOS_VX_1X0
endif
ifeq ($(PLATFORM),INF_TWINPASS)
WFLAGS += -DRT_BIG_ENDIAN -DINF_TWINPASS
endif
ifeq ($(PLATFORM),INF_DANUBE)
ifneq (,$(findstring 2.4,$(LINUX_SRC)))
# Linux 2.4
WFLAGS += -DINF_DANUBE -DRT_BIG_ENDIAN
else
# Linux 2.6
WFLAGS += -DRT_BIG_ENDIAN
endif
endif
ifeq ($(PLATFORM),INF_AR9)
WFLAGS += -DRT_BIG_ENDIAN -DINF_AR9
# support MAPI function for AR9.
#WFLAGS += -DAR9_MAPI_SUPPORT
endif
ifeq ($(PLATFORM),INF_VR9)
WFLAGS += -DRT_BIG_ENDIAN -DINF_AR9 -DINF_VR9
endif
ifeq ($(PLATFORM),CAVM_OCTEON)
WFLAGS += -DRT_BIG_ENDIAN
endif
ifeq ($(PLATFORM),BRCM_6358)
WFLAGS += -DRT_BIG_ENDIAN -DBRCM_6358
endif
ifeq ($(PLATFORM),INF_AMAZON_SE)
WFLAGS += -DRT_BIG_ENDIAN -DINF_AMAZON_SE
endif
ifeq ($(PLATFORM),RALINK_3052)
WFLAGS += -DPLATFORM_RALINK_3052
endif
ifeq ($(PLATFORM),FREESCALE8377)
#EXTRA_CFLAGS := -v -I$(RT28xx_DIR)/include -I$(LINUX_SRC)/include $(WFLAGS)-O2 -Wall -Wstrict-prototypes -Wno-trigraphs
#export EXTRA_CFLAGS
WFLAGS += -DRT_BIG_ENDIAN
EXTRA_CFLAGS := $(WFLAGS) -I$(RT28xx_DIR)/include
endif
ifeq ($(PLATFORM),ST)
#WFLAGS += -DST
WFLAGS += -DST
endif
#kernel build options for 2.4
# move to Makefile outside LINUX_SRC := /opt/star/kernel/linux-2.4.27-star
ifeq ($(PLATFORM),RALINK_3052)
CFLAGS := -D__KERNEL__ -I$(LINUX_SRC)/include/asm-mips/mach-generic -I$(LINUX_SRC)/include -I$(RT28xx_DIR)/include -Wall -Wstrict-prototypes -Wno-trigraphs -O2 -fno-strict-aliasing -fno-common -fomit-frame-pointer -G 0 -mno-abicalls -fno-pic -pipe -finline-limit=100000 -march=mips2 -mabi=32 -Wa,--trap -DLINUX -nostdinc -iwithprefix include $(WFLAGS)
export CFLAGS
endif
ifeq ($(PLATFORM), RALINK_2880)
CFLAGS := -D__KERNEL__ -I$(LINUX_SRC)/include -I$(RT28xx_DIR)/include -Wall -Wstrict-prototypes -Wno-trigraphs -O2 -fno-strict-aliasing -fno-common -fomit-frame-pointer -G 0 -mno-abicalls -fno-pic -pipe -finline-limit=100000 -march=mips2 -mabi=32 -Wa,--trap -DLINUX -nostdinc -iwithprefix include $(WFLAGS)
export CFLAGS
endif
ifeq ($(PLATFORM),STAR)
CFLAGS := -D__KERNEL__ -I$(LINUX_SRC)/include -I$(RT28xx_DIR)/include -Wall -Wstrict-prototypes -Wno-trigraphs -O2 -fno-strict-aliasing -fno-common -Uarm -fno-common -pipe -mapcs-32 -D__LINUX_ARM_ARCH__=4 -march=armv4 -mshort-load-bytes -msoft-float -Uarm -DMODULE -DMODVERSIONS -include $(LINUX_SRC)/include/linux/modversions.h $(WFLAGS)
export CFLAGS
endif
ifeq ($(PLATFORM),SIGMA)
CFLAGS := -D__KERNEL__ -I$(RT28xx_DIR)/include -I$(LINUX_SRC)/include -I$(LINUX_SRC)/include/asm/gcc -I$(LINUX_SRC)/include/asm-mips/mach-tango2 -I$(LINUX_SRC)/include/asm-mips/mach-tango2 -DEM86XX_CHIP=EM86XX_CHIPID_TANGO2 -DEM86XX_REVISION=6 -I$(LINUX_SRC)/include/asm-mips/mach-generic -I$(RT2860_DIR)/include -Wall -Wundef -Wstrict-prototypes -Wno-trigraphs -fno-strict-aliasing -fno-common -ffreestanding -O2 -fomit-frame-pointer -G 0 -mno-abicalls -fno-pic -pipe -mabi=32 -march=mips32r2 -Wa,-32 -Wa,-march=mips32r2 -Wa,-mips32r2 -Wa,--trap -DMODULE $(WFLAGS) -DSIGMA863X_PLATFORM
export CFLAGS
endif
ifeq ($(PLATFORM),SIGMA_8622)
CFLAGS := -D__KERNEL__ -I$(CROSS_COMPILE_INCLUDE)/include -I$(LINUX_SRC)/include -I$(RT28xx_DIR)/include -Wall -Wstrict-prototypes -Wno-trigraphs -O2 -fno-strict-aliasing -fno-common -fno-common -pipe -fno-builtin -D__linux__ -DNO_MM -mapcs-32 -march=armv4 -mtune=arm7tdmi -msoft-float -DMODULE -mshort-load-bytes -nostdinc -iwithprefix -DMODULE $(WFLAGS)
export CFLAGS
endif
ifeq ($(PLATFORM),5VT)
CFLAGS := -D__KERNEL__ -I$(LINUX_SRC)/include -I$(RT28xx_DIR)/include -mlittle-endian -Wall -Wundef -Wstrict-prototypes -Wno-trigraphs -fno-strict-aliasing -fno-common -O3 -fno-omit-frame-pointer -fno-optimize-sibling-calls -fno-omit-frame-pointer -mapcs -mno-sched-prolog -mabi=apcs-gnu -mno-thumb-interwork -D__LINUX_ARM_ARCH__=5 -march=armv5te -mtune=arm926ej-s --param max-inline-insns-single=40000 -Uarm -Wdeclaration-after-statement -Wno-pointer-sign -DMODULE $(WFLAGS)
export CFLAGS
endif
ifeq ($(PLATFORM),IKANOS_V160)
CFLAGS := -D__KERNEL__ -I$(LINUX_SRC)/include -I$(LINUX_SRC)/include/asm/gcc -I$(LINUX_SRC)/include/asm-mips/mach-tango2 -I$(LINUX_SRC)/include/asm-mips/mach-tango2 -I$(LINUX_SRC)/include/asm-mips/mach-generic -I$(RT28xx_DIR)/include -Wall -Wundef -Wstrict-prototypes -Wno-trigraphs -fno-strict-aliasing -fno-common -ffreestanding -O2 -fomit-frame-pointer -G 0 -mno-abicalls -fno-pic -pipe -march=lx4189 -Wa, -DMODULE $(WFLAGS)
export CFLAGS
endif
ifeq ($(PLATFORM),IKANOS_V180)
CFLAGS := -D__KERNEL__ -I$(LINUX_SRC)/include -I$(LINUX_SRC)/include/asm/gcc -I$(LINUX_SRC)/include/asm-mips/mach-tango2 -I$(LINUX_SRC)/include/asm-mips/mach-tango2 -I$(LINUX_SRC)/include/asm-mips/mach-generic -I$(RT28xx_DIR)/include -Wall -Wundef -Wstrict-prototypes -Wno-trigraphs -fno-strict-aliasing -fno-common -ffreestanding -O2 -fomit-frame-pointer -G 0 -mno-abicalls -fno-pic -pipe -mips32r2 -Wa, -DMODULE $(WFLAGS)
export CFLAGS
endif
ifeq ($(PLATFORM),INF_TWINPASS)
CFLAGS := -D__KERNEL__ -DMODULE -I$(LINUX_SRC)/include -I$(RT28xx_DIR)/include -Wall -Wstrict-prototypes -Wno-trigraphs -O2 -fomit-frame-pointer -fno-strict-aliasing -fno-common -G 0 -mno-abicalls -fno-pic -march=4kc -mips32 -Wa,--trap -pipe -mlong-calls $(WFLAGS)
export CFLAGS
endif
ifeq ($(PLATFORM),INF_DANUBE)
ifneq (,$(findstring 2.4,$(LINUX_SRC)))
CFLAGS := -I$(RT28xx_DIR)/include $(WFLAGS) -Wundef -fno-strict-aliasing -fno-common -ffreestanding -Os -fomit-frame-pointer -G 0 -mno-abicalls -fno-pic -pipe -msoft-float -mabi=32 -march=mips32 -Wa,-32 -Wa,-march=mips32 -Wa,-mips32 -Wa,--trap -I$(LINUX_SRC)/include/asm-mips/mach-generic
else
CFLAGS := -I$(RT28xx_DIR)/include $(WFLAGS) -Wundef -fno-strict-aliasing -fno-common -ffreestanding -Os -fomit-frame-pointer -G 0 -mno-abicalls -fno-pic -pipe -msoft-float -mabi=32 -march=mips32r2 -Wa,-32 -Wa,-march=mips32r2 -Wa,-mips32r2 -Wa,--trap -I$(LINUX_SRC)/include/asm-mips/mach-generic
endif
export CFLAGS
endif
ifeq ($(PLATFORM),INF_AR9)
CFLAGS := -I$(RT28xx_DIR)/include $(WFLAGS) -Wundef -fno-strict-aliasing -fno-common -fno-pic -ffreestanding -Os -fomit-frame-pointer -G 0 -mno-abicalls -fno-pic -pipe -msoft-float -mabi=32 -mlong-calls -march=mips32r2 -mtune=34kc -march=mips32r2 -Wa,-32 -Wa,-march=mips32r2 -Wa,-mips32r2 -Wa,--trap -I$(LINUX_SRC)/include/asm-mips/mach-generic
export CFLAGS
endif
ifeq ($(PLATFORM),INF_VR9)
CFLAGS := -I$(RT28xx_DIR)/include $(WFLAGS) -Wundef -fno-strict-aliasing -fno-common -fno-pic -ffreestanding -Os -fomit-frame-pointer -G 0 -mno-abicalls -fno-pic -pipe -msoft-float -mabi=32 -mlong-calls -march=mips32r2 -march=mips32r2 -Wa,-32 -Wa,-march=mips32r2 -Wa,-mips32r2 -Wa,--trap -I$(LINUX_SRC)/include/asm-mips/mach-generic
export CFLAGS
endif
ifeq ($(PLATFORM),BRCM_6358)
CFLAGS := $(WFLAGS) -I$(RT28xx_DIR)/include -nostdinc -iwithprefix include -D__KERNEL__ -Wall -Wstrict-prototypes -Wno-trigraphs -fno-strict-aliasing -fno-common -I $(LINUX_SRC)/include/asm/gcc -G 0 -mno-abicalls -fno-pic -pipe -finline-limit=100000 -mabi=32 -march=mips32 -Wa,-32 -Wa,-march=mips32 -Wa,-mips32 -Wa,--trap -I$(LINUX_SRC)/include/asm-mips/mach-bcm963xx -I$(LINUX_SRC)/include/asm-mips/mach-generic -Os -fomit-frame-pointer -Wdeclaration-after-statement -DMODULE -mlong-calls
export CFLAGS
endif
ifeq ($(PLATFORM),INF_AMAZON_SE)
CFLAGS := -D__KERNEL__ -DMODULE=1 -I$(LINUX_SRC)/include -I$(RT28xx_DIR)/include -Wall -Wstrict-prototypes -Wno-trigraphs -O2 -fno-strict-aliasing -fno-common -DCONFIG_IFX_ALG_QOS -DCONFIG_WAN_VLAN_SUPPORT -fomit-frame-pointer -DIFX_PPPOE_FRAME -G 0 -fno-pic -mno-abicalls -mlong-calls -pipe -finline-limit=100000 -mabi=32 -march=mips32 -Wa,-32 -Wa,-march=mips32 -Wa,-mips32 -Wa,--trap -nostdinc -iwithprefix include $(WFLAGS)
export CFLAGS
endif
ifeq ($(PLATFORM),ST)
CFLAGS := -D__KERNEL__ -I$(LINUX_SRC)/include -I$(RT28xx_DIR)/include -Wall -O2 -Wundef -Wstrict-prototypes -Wno-trigraphs -Wdeclaration-after-statement -Wno-pointer-sign -fno-strict-aliasing -fno-common -fomit-frame-pointer -ffreestanding -m4-nofpu -o $(WFLAGS)
export CFLAGS
endif
ifeq ($(PLATFORM),PC)
ifneq (,$(findstring 2.4,$(LINUX_SRC)))
# Linux 2.4
CFLAGS := -D__KERNEL__ -I$(LINUX_SRC)/include -I$(RT28xx_DIR)/include -O2 -fomit-frame-pointer -fno-strict-aliasing -fno-common -pipe -mpreferred-stack-boundary=2 -march=i686 -DMODULE -DMODVERSIONS -include $(LINUX_SRC)/include/linux/modversions.h $(WFLAGS)
export CFLAGS
else
# Linux 2.6
EXTRA_CFLAGS := $(WFLAGS) -I$(RT28xx_DIR)/include
endif
endif
#If the kernel version of RMI is newer than 2.6.27, please change "CFLAGS" to "EXTRA_FLAGS"
ifeq ($(PLATFORM),RMI)
EXTRA_CFLAGS := -D__KERNEL__ -DMODULE=1 -I$(LINUX_SRC)/include -I$(LINUX_SRC)/include/asm-mips/mach-generic -I$(RT28xx_DIR)/include -Wall -Wstrict-prototypes -Wno-trigraphs -O2 -fno-strict-aliasing -fno-common -DCONFIG_IFX_ALG_QOS -DCONFIG_WAN_VLAN_SUPPORT -fomit-frame-pointer -DIFX_PPPOE_FRAME -G 0 -fno-pic -mno-abicalls -mlong-calls -pipe -finline-limit=100000 -mabi=32 -G 0 -mno-abicalls -fno-pic -pipe -msoft-float -march=xlr -ffreestanding -march=xlr -Wa,--trap, -nostdinc -iwithprefix include $(WFLAGS)
export EXTRA_CFLAGS
endif
ifeq ($(PLATFORM),RMI_64)
EXTRA_CFLAGS := -D__KERNEL__ -DMODULE=1 -I$(LINUX_SRC)/include -I$(LINUX_SRC)/include/asm-mips/mach-generic -I$(RT28xx_DIR)/include -Wall -Wstrict-prototypes -Wno-trigraphs -O2 -fno-strict-aliasing -fno-common -DCONFIG_IFX_ALG_QOS -DCONFIG_WAN_VLAN_SUPPORT -fomit-frame-pointer -DIFX_PPPOE_FRAME -G 0 -fno-pic -mno-abicalls -mlong-calls -pipe -finline-limit=100000 -mabi=64 -G 0 -mno-abicalls -fno-pic -pipe -msoft-float -march=xlr -ffreestanding -march=xlr -Wa,--trap, -nostdinc -iwithprefix include $(WFLAGS)
export EXTRA_CFLAGS
endif
ifeq ($(PLATFORM),IXP)
CFLAGS := -v -D__KERNEL__ -DMODULE -I$(LINUX_SRC)/include -I$(RT28xx_DIR)/include -mbig-endian -Wall -Wstrict-prototypes -Wno-trigraphs -O2 -fno-strict-aliasing -fno-common -Uarm -fno-common -pipe -mapcs-32 -D__LINUX_ARM_ARCH__=5 -mcpu=xscale -mtune=xscale -malignment-traps -msoft-float $(WFLAGS)
EXTRA_CFLAGS := -v $(WFLAGS) -I$(RT28xx_DIR)/include -mbig-endian
export CFLAGS
endif
ifeq ($(PLATFORM),SMDK)
EXTRA_CFLAGS := $(WFLAGS) -I$(RT28xx_DIR)/include
endif
ifeq ($(PLATFORM),CAVM_OCTEON)
EXTRA_CFLAGS := $(WFLAGS) -I$(RT28xx_DIR)/include \
-mabi=64 $(WFLAGS)
export CFLAGS
endif
ifeq ($(PLATFORM),DM6446)
CFLAGS := -nostdinc -iwithprefix include -D__KERNEL__ -I$(RT28xx_DIR)/include -I$(LINUX_SRC)/include -Wall -Wstrict-prototypes -Wno-trigraphs -fno-strict-aliasing -fno-common -Os -fno-omit-frame-pointer -fno-omit-frame-pointer -mapcs -mno-sched-prolog -mlittle-endian -mabi=apcs-gnu -D__LINUX_ARM_ARCH__=5 -march=armv5te -mtune=arm9tdmi -msoft-float -Uarm -Wdeclaration-after-statement -c -o $(WFLAGS)
export CFLAGS
endif
ifeq ($(PLATFORM),BL2348)
CFLAGS := -D__KERNEL__ -I$(RT28xx_DIR)/include -I$(LINUX_SRC)/include -I$(LINUX_SRC)/include/asm/gcc -I$(LINUX_SRC)/include/asm-mips/mach-tango2 -I$(LINUX_SRC)/include/asm-mips/mach-tango2 -DEM86XX_CHIP=EM86XX_CHIPID_TANGO2 -DEM86XX_REVISION=6 -I$(LINUX_SRC)/include/asm-mips/mach-generic -I$(RT2860_DIR)/include -Wall -Wundef -Wstrict-prototypes -Wno-trigraphs -fno-strict-aliasing -fno-common -ffreestanding -O2 -fomit-frame-pointer -G 0 -mno-abicalls -fno-pic -pipe -mabi=32 -march=mips32r2 -Wa,-32 -Wa,-march=mips32r2 -Wa,-mips32r2 -Wa,--trap -DMODULE $(WFLAGS) -DSIGMA863X_PLATFORM -DEXPORT_SYMTAB -DPLATFORM_BL2348
export CFLAGS
endif
ifeq ($(PLATFORM),BLUBB)
CFLAGS := -D__KERNEL__ -I$(RT28xx_DIR)/include -I$(LINUX_SRC)/include -I$(LINUX_SRC)/include/asm/gcc -I$(LINUX_SRC)/include/asm-mips/mach-tango2 -I$(LINUX_SRC)/include/asm-mips/mach-tango2 -DEM86XX_CHIP=EM86XX_CHIPID_TANGO2 -DEM86XX_REVISION=6 -I$(LINUX_SRC)/include/asm-mips/mach-generic -I$(RT2860_DIR)/include -Wall -Wundef -Wstrict-prototypes -Wno-trigraphs -fno-strict-aliasing -fno-common -ffreestanding -O2 -fomit-frame-pointer -G 0 -mno-abicalls -fno-pic -pipe -mabi=32 -march=mips32r2 -Wa,-32 -Wa,-march=mips32r2 -Wa,-mips32r2 -Wa,--trap -DMODULE $(WFLAGS) -DSIGMA863X_PLATFORM -DEXPORT_SYMTAB -DPLATFORM_BL2348
export CFLAGS
endif
ifeq ($(PLATFORM),BLPMP)
CFLAGS := -D__KERNEL__ -I$(RT28xx_DIR)/include -I$(LINUX_SRC)/include -I$(LINUX_SRC)/include/asm/gcc -I$(LINUX_SRC)/include/asm-mips/mach-tango2 -I$(LINUX_SRC)/include/asm-mips/mach-tango2 -DEM86XX_CHIP=EM86XX_CHIPID_TANGO2 -DEM86XX_REVISION=6 -I$(LINUX_SRC)/include/asm-mips/mach-generic -I$(RT2860_DIR)/include -Wall -Wundef -Wstrict-prototypes -Wno-trigraphs -fno-strict-aliasing -fno-common -ffreestanding -O2 -fomit-frame-pointer -G 0 -mno-abicalls -fno-pic -pipe -mabi=32 -march=mips32r2 -Wa,-32 -Wa,-march=mips32r2 -Wa,-mips32r2 -Wa,--trap -DMODULE $(WFLAGS) -DSIGMA863X_PLATFORM -DEXPORT_SYMTAB
export CFLAGS
endif
ifeq ($(PLATFORM),MT85XX)
ifneq (,$(findstring 2.4,$(LINUX_SRC)))
# Linux 2.4
CFLAGS := -D__KERNEL__ -I$(LINUX_SRC)/include -I$(RT28xx_DIR)/include -O2 -fomit-frame-pointer -fno-strict-aliasing -fno-common -pipe -mpreferred-stack-boundary=2 -march=i686 -DMODULE -DMODVERSIONS -include $(LINUX_SRC)/include/linux/modversions.h $(WFLAGS)
export CFLAGS
else
# Linux 2.6
EXTRA_CFLAGS += $(WFLAGS) -I$(RT28xx_DIR)/include
EXTRA_CFLAGS += -D _NO_TYPEDEF_BOOL_ \
-D _NO_TYPEDEF_UCHAR_ \
-D _NO_TYPEDEF_UINT8_ \
-D _NO_TYPEDEF_UINT16_ \
-D _NO_TYPEDEF_UINT32_ \
-D _NO_TYPEDEF_UINT64_ \
-D _NO_TYPEDEF_CHAR_ \
-D _NO_TYPEDEF_INT32_ \
-D _NO_TYPEDEF_INT64_ \
endif
endif
ifeq ($(PLATFORM),NXP_TV550)
ifneq (,$(findstring 2.4,$(LINUX_SRC)))
# Linux 2.4
CFLAGS := -D__KERNEL__ -I$(LINUX_SRC)/include -I$(RT28xx_DIR)/include -O2 -fomit-frame-pointer -fno-strict-aliasing -fno-common -pipe -mpreferred-stack-boundary=2 -march=mips -DMODULE -DMODVERSIONS -include $(LINUX_SRC)/include/linux/modversions.h $(WFLAGS)
export CFLAGS
else
# Linux 2.6
EXTRA_CFLAGS := $(WFLAGS) -I$(RT28xx_DIR)/include
endif
endif
ifeq ($(PLATFORM),MVL5)
CFLAGS := -D__KERNEL__ -I$(LINUX_SRC)/include -I$(RT28xx_DIR)/include -mlittle-endian -Wall -Wundef -Wstrict-prototypes -Wno-trigraphs -fno-strict-aliasing -fno-common -O3 -fno-omit-frame-pointer -fno-optimize-sibling-calls -fno-omit-frame-pointer -mapcs -mno-sched-prolog -mno-thumb-interwork -D__LINUX_ARM_ARCH__=5 -march=armv5te -mtune=arm926ej-s --param max-inline-insns-single=40000 -Uarm -Wdeclaration-after-statement -Wno-pointer-sign -DMODULE $(WFLAGS)
export CFLAGS
endif -
Recommendations for USB WiFi Adapter
I'm wondering if anyone has any recommendations on a specific brand/model USB WiFi adapter that would be compatible with OS X Leopard (10.5.5). Ideally, I'd like it to have the following features:
- USB 2.0
- 802.11b/g
- External antenna/port
I've used a Hawking HWUG1A, which worked great for about a year, then died (actually, now it causes a kernel panic after using it for a while... Hawking Tech Support said it was probably a hardware failure in the card, but I'm out of warranty).
Thanks for any thoughts/suggestions/input.Hello.
So, I have received G54SL USB wireless card. Installation was simple but I still needed to install it twice before it worked. Installation indicated that it was for Tiger even though I choose 10.5 package. Setting parameters was easy enough.
So far I tested it on my MiniMac which is placed in a distant corner of my apartment where reception with AirPort card was not very good.
My impressions: the reception with G54SL was better than with the Mini's airport card. I plugged it directly to the Mini, without extension cable. This suggests that I could have even stronger signal if I move USB around when connected to the computer via extension cable. The signal was stable with time.
When computer waked up from sleep it reconnected fast. However, when I restarted computer I needed to choose my network again. It took some time before the connection was established. I did not read manual yet and I do not know if I can make card remember my network and reconnect automatically.
I would say that if you need to extended range and have stable connection this card is more reliable than the built-in Airport card (at least in my case). I still need to try it with my portable computers and test behavior with networks other than mine. I'll try this during the next week. -
Why AdobePPro CS4 won't work properly with Win7 Ultimate OS
Can u please explain why Adobe PremierePro CS4 won'r work properly with Windows 7 Ultimate?? Is it because of a "bit" differences?? or for any other reason?? I have freezing problems on time line.. I am using Sony XD EX1 clips on the time line. Sometimes it works up to Dynamic LInk Encore and when it starts encoding, after few seconds it gives an error message "Encode failed" My computer config: WIN7 Ultimate/ Xeon 2.4 GHz, 12 GB RAM, Nvidia FX3800 Video card with 1GB RAM, C:\ 1TB SASHDD on RAID 5 system, D:\600 GB SAS HDD (not on RAID) Any thoughts to get it going? Thanks
Read A fix via Virtual XP
http://forums.adobe.com/thread/702693?tstart=0 -
IPOD won't work properly if drive C: is available on your computer
The Windows XP driver for the Apple IPOD USB Device has a bug that makes your system very slow or even hang when you try to connect or eject your IPOD if Drive "C:" is available on your machine. Another symptom is that when you connect your ipod, the computer doesn't automatically launch the ITunes app and it is very slow to open manually.
A typical problem is that if your system has had a hard drive replaced and/or the drive "C" is not assigned for some reason, then the IPOD USB Driver will attach itself as drive "C:" and then it won't work properly seemingly because of conflicts with the Windows OS. Other USB devices never grab drive "C:" but this Apple-supplied device driver appears to think it is OK to use drive C: but then it doesn't work properly.
The fix is to make sure some real (physical) drive is always connected to or mapped to drive "C:" so that the IPOD USB driver attaches to a drive from "D:" and up.
Also try reading: http://docs.info.apple.com/article.html?artnum=93499 for more info.yeah, the ipod normally gets assigned the f, g, or h drive letters. i don't really know though if windows is responsible for assigning the drive letters to usb devices or the ipod driver. to my understanding the ipodservice.exe only makes sure that itunes can comunicate to the ipod through the drive letter that windows assigns to the ipod. windows is the os and therefore responsible for managinig its drive letters.
-
USB WiFi adapter that can replace iMac Airport
After trying all of the workarounds posted in the forums to address the sporadic wifi problems, I've had it. Apple does not seem willing to address it, so I either relegate my 24" iMac to being nothing more than a DVD player in the spare room or I find a meaningful resolution. I've read that some people have started using a separate USB WiFi adapter.
Any consensus on whether some models work better/worse than others?
Anyone had long term success with one they can report?
After 17 years of Macs, this is the first one I have had with widespread problems and I'm quite dismayed that Apple has, thus far, ignored it.Listen... a Mac is a computer like a Windows PC. It's hard drive can have data corruption too. And you may have even installed some third-party software that is causing this problem, such as a custom kernel extension. Or you may have inadvertently deleted or moved some key system component. There are many possibilities, but the solution of last resort (for any computer since personal computers had hard drives) has been to back up personal data, erase the hard drive, and re-install. If you go to the Genius Bar at an Apple Store, they'll do some trouble-shooting and if they can't figure it out with reasonable effort, they'll erase the drive and re-install the OS. If that does not resolve the issue, they'll conclude it is a hardware problem start investigating which component is faulty.
If Macs never failed or had issues related to its hard drive, Apple would not have created Time Machine so users can do ongoing backups without thinking about it.
I have no idea what you have tried, since you have did not specifically state it. You should have already tried these three basic steps
Run Disk Utility and use +Repair Disk Permissions+ on the +First Aid+ tab
Reset PRAM - http://support.apple.com/kb/HT1379
Reset SMC - http://support.apple.com/kb/HT1543
And before doing an erase and install, you should try one more thing as a test. Create a new admin user account in System Preferences Accounts pane
http://docs.info.apple.com/article.html?path=Mac/10.5/en/8235.html
Log out and log in to the new account. Try wireless networking while logged into this new account. Does it work better or is it the same?
If there is improvement, the cause is likely to be confined to your normal user account and not the overall system or hardware. It may be a corrupted user preferences setting or some third-party process that is running in the background. Be sure to check System Preferences Accounts pane +Login Items+ tab (in your normal account) and review the processes that start up automatically at login.
If there is no change, the cause is likely to be related to the overall system installation or to hardware. Backing up your data, erasing the hard drive, and re-installing will serve to either resolve the problem, or rule out a software-related cause (pointing to a hardware-related cause).
If you have questions about doing an erase and re-install, please post back. -
I am trying to capture Wifi signals beyond what the built-in Wifi radio of my T61 can receive. I have a Alfa 500 which uses a Realtek 8187 driver. I would like to continue to use Access Connections instead of another utility. I noticed that under tools in Access Connections, a wireless USB selection is greyed out. Is there a way to activate this optional tool and use a USB Wifi adapter?
svADENA wrote:
Is there a way to activate this optional tool and use a USB Wifi adapter?
Not at this time. It seems to be a feature which is not yet enabled. Presumably Lenovo has some plan for its use in the future, but I suspect that use may be related to USB connected WWAN devices, not WiFi devices.
Tell me more about these WiFi signal you can't access with your T61 internal WiFi?
Cheers,
Bill
Message Edited by billbolton on 02-28-2009 10:06 AM
I don't work for Lenovo -
How can I add Qualcom Atheros USB wifi adapter?
I need to add a Qualcom USB wifi adapter to my 2014 Macbook Pro retina, running latest Yosemite. I need to do this in order for a Parallels virtual machine to use wifi connection, rather than a bridged ethernet connection (the guest VM cannot 'see' the Macbook wifi adapter)
The wifi chipset is Atheros AR9271, but I can't find any Mac OS X drivers. Has anyone added this type of USB wifi adapter?
When I run the command system_profiler SBUSBData_Type the following information is shown, which tells me that the Macbook can see the device, I just don't know how to configure it
Product ID: 0x3327
Vendor ID: 0x13d3 (AzureWave Technologies, Inc.)
Version: 1.08
Serial Number: 12345
Speed: Up to 480 Mb/sec
Manufacturer: ATHEROS
Location ID: 0x14100000 / 7
Current Available (mA): 500
Current Required (mA): Unknown (Device has not been configured)
thanks in advance!Considering the different options that PC could have been ordered with, it might be there is not an empty slot to mount a PCI add-on card to add a USB 3.0 card. It would be advisable to open the case to see if there is an empty slot. If there is, then THIS is a choice to add USB 3.0
{---------- Please click the "Thumbs Up" to say thanks for helping.
Please click "Accept As Solution" if my help has solved your problem. ----------}
This is a user supported forum. I am a volunteer and I do not work for HP. -
COMPATIBLE USB WiFi ADAPTER/DONGLES FOR HP 470 MOBILE PRINTERS???
I've misplaced the HP USB WIFI dongle/adapter (HP Q6274A) to my H470 mobile printer and was wondering if another (Non HP) usb wifi adapter/dongle will work...until I find my original HP Q6274A dongle? Incidentally, I happened to notice Non-HP WiFi USB adapter/dongles are every where, they are very inexpensive and also offer the latest WiFi technology enhancements, ie: b/g/n & 300 Mbp/s, etc. I'm hopeful HP customer support will offer a few suggestions regarding other compatible H470 WiFi dongles... however, I doubt they'll suggest anything other than their hard to find/obsolete HP Q6274A ... any thoughts would be greatly appreciated =)
Hi xxwildbilxx,
Are you still experiencing issues? The adaptors may or may not work. If you have a spare, it is certainly worth a try, however I cannot guarantee compatibility. The specific adaptor for this model is readily available through online ordering systems. You can also contact HP technical support to compare best pricing options for these adaptors. Global contact information can be accessed Here.
Hope this helps!
Also, remember a click on the Kudos star to the left is a quick "Thanks" for a helpful post.
Please select the "Accept as Solution" button on the post that best answers your question.
I appreciate your input !
Thank You,
I work for HP. -
Windows reports that the "USB-IF xHCI USB Host Controller" device is not working properly.
I have been receiving the following error and instructions to fix it for a long time now, prior to updating to Windows 8.1:
A device is not working properly
Windows reports that the "USB-IF xHCI USB Host Controller" device is not working properly.
Recommended solution to the problemUse Windows Update to check whether new device drivers are available. Proceed as follows:
Open Device Manager
Search in the device manager for the device whose driver you would like to update and double-click on the device name. You may first have to enable the "Show hidden devices" entry in the "View" menu.
Switch to the Driver tab, click Update driver and follow the instructions
When I follow the instructions and try to update the driver, I am told "The best driver software for your device is already installed."
How do I update the driver to stop receiving the error?
This question was solved.
View Solution.I have solved the initial problem.
I found the solution on the Forum at http://h10025.www1.hp.com/ewfrf/wc/document?docname=c03926756&tmp_task=solveCategory&cc=us&dlc=en&la... -
Iphoto9 won't work properly in Snow Leopard
On my Macbook (2008) iphoto9 won't work properly in Snow Leopard. What do I do? Upgrade to iphoto 11 or is there another way?
I was happy with iphoto9.Had a look around the message boards and found this link, has solved the problem.
http://www.apple.com/support/downloads/proapplicationsupport31macosx104.html
Maybe you are looking for
-
I can't move an app from one screen to another screen
I can't move an app from one screen to another screen
-
Wrap Up - When i make the call don't appears Wrapup Pop-up
Hello guys, I read this guide: http://www.ciscosistemi.com/en/US/docs/voice_ip_comm/cust_contact/contact_center/ctios/ctios7_5/install/guide/cti75smg.pdf This guide shows that you can change the Wrap Up Mode. But I need to know how can I change the p
-
I am able to type in the address bar, but when I hit enter, nothing happens. And I don't like using Internet Explorer. This happens when I try to acccess my hotmail account. I never had this problem with other versions of Firefox.
-
I got an iTunes gift card for Christmas and I was making an account in iTunes (I had always put music from CDs onto my ipod, rather than purchasing from iTunes, so I'm new to this). I made the account, put in a credit card number, and then clicked Re
-
Unknown error - will not sync with iTunes
My 80gb video iPod worked fine until yesterday. Now every time I try to sync with iTunes an unknown error occurs and it won't update from the Library. Have tried everything suggested, even restoring and have consequently lost all music from the iPod