USB2.0 Install Troubles With WinXP and KT3 Ultra2?

I installed WinXP (Fresh) on my system with the KT3 Ultra2 board in it. I had ACPI (Plug and Play OS Installed) turned OFF in the bios, and I have all 6 USB ports enabled in bios (legacy support off).
Upon installing WinXP and the SP1 full update (~130mb file I believe), I check the device manager to see what was up so far. I had several yellow exclamation marks, but two of the three were expected (onboard audio and my video card had no drivers yet). But the third one threw me... Under "Other devices" I had "USB Host Controller" listed....
So I installed the Via 4in1's version 4.43 using the "quick install" option. Check device manager, same result. Mr. Steveo suggested I try right clicking the controller in the device manager and choosing to "update driver". I did, and it automatically updated the driver and placed it in the USB section of the device manager (with the other USB entries).
The problem is, the device name seems weird: "Enhanced PCI to USB Host Controller" instead of something like "USB2.0 PCI to USB Host Controller" or something like that. The yellow exclamation mark is gone, but I just dont know if this is the correct device setup or not.
Can any of you other Ultra2 owners tell me if this is what you have in your USB controller list, and if not, how did you install WinXP to get to the point where you had the "correct" listing? Maybe it makes a difference whether ACPI is turned on during install or something?
I tried to run the Via USB2.0 driver file (7011Kb) from the MSI site to see if it would help, but it quits the install and says that the SP1 update drivers are newer and should not be updated with this driver.
Any suggestions or comments are very much appreciated.
Kyle
Detroit, MI

Quote
Originally posted by Stevesmith
I have a new 845E Max2 motherboard and installed Windows XP.
I have a similar USB2 problem after installing XP SP1 - yellow question marks in the hardware manager under "Other Hardware"/"USB (Universal Serial Bus)-Controller".
I tried "Uninstalling" the USB controller as was suggested in the forum, but it won't let itself be removed.
When I try "Search for new hardware" it shows a message that an error occurred when installing the hardware, and that the hardware is not properly configured (Code 1). It suggests that I re-install the driver. When I select "re-install driver", I just get another error message. It asks me if I have a CD or disk wit drivers, but I can't find anything appropriate on the driver disk I got with the motherboard.
Does anyone have an idea what's wrong?
Regards Steve
Hi, yours is 845E MAX2 motherboard, you should use Intel USB2.0 drivers .
http://www.msi.com.tw/program/support/driver/dvr/spt_dvr_list.php
And don't use "search for new hardware", instead you manually point the drivers location to where you extracted the downloaded file. Sometimes WinXP drivers search is "blind" 8)

Similar Messages

I downloaded Firefox 4.0 and it says to re-install the toolbar but I have not been successful in doing so. Can I go back to the older version? I had no trouble with that and I do not like this new version at all.

I downloaded Firefox 4.0 and it says to re-install the toolbar but I have not been successful in doing so. I went to the forums and tried all the suggested fixes but none worked. Can I go back to the older version? I had no trouble with that and I do not like this new version at all. I tried a system restore twice and it did not fix the problem.

I would imagine it's the MyWay Searchbar which is classified by most anti-malware scanners as adware, or even worse as spyware. I say that because I see "SmileyCentral" in your list of plugins and that's an add-on for that particular toolbar. You can disable that via Tools | Add-ons | Plugins.
There are a number of toolbars which won't work with Firefox 4 anymore due to the enhanced protection mechanisms in the browser.
Mozilla recommends that you only install add-ons from its own security site @ https://addons.mozilla.org/en-US/firefox/?browse=featured Generally speaking, those have all been tested and approved. The exceptions are those currently under review which are marked with a yellow banner to warn users that they haven't passed Mozilla's labs yet.

I am having all kinds of trouble with itunes and updating my ipad. when I open up itunes, it seems to just sit there, never going to itunes store. when I connect my ipad, I check update and it starts, but then I get this message:backup can't be saved on

I am having all kinds of trouble with itunes and updating my ipad. I open itunes up but it doesn't do anything except open to a blank screen. I try to access the itunes store but it won't go there. When I connect my ipad, and try to update it, it starts and then I get a message that says backup cannot be saved on this computer. I have tried everything suggested to no avail. This is the 2nd or 3rd time I have had problems with itunes. Sometimes I even get a message that I am not connected to the internet.
I have uninstalled and re-installed. Any help?

You might not have enough space left on your hardrive.

Just bought a new iPhone and am having trouble with iTunes and App Store. I can log in to Cloud, iTunes, and app store but once I try to download, it says "Youe apple id has been disabled". I've reset my password three times and have no issue on my Pad.

Just bought a new iPhone and am having trouble with iTunes and App Store. I can log in to Cloud, iTunes, and app store but once I try to download, it says "Youe apple id has been disabled". I've reset my password three times and have no issue on my Pad.

Hi FuzzyDunlopIsMe,
Welcome to the Support Communities!
It's possible that resetting your password multiple times has triggered this security. Click on the link below for assistance with your Apple ID Account:
Apple ID: Contacting Apple for help with Apple ID account security
http://support.apple.com/kb/HT5699
Here is some additional information regarding your Apple ID:
Apple ID: 'This Apple ID has been disabled for security reasons' alert appears
http://support.apple.com/kb/ts2446
Frequently asked questions about Apple ID
http://support.apple.com/kb/HT5622
Click on My Apple ID to access and edit your account.
Cheers,
- Judy

Trouble with Mail and Maverick

Trouble with Maverick and Mail - contacts (groups) will not load into address bar in mail.

Check that the mac's preferences for icloud is still connected to the proper account. Be sure photo stream is turned on.
You haven't described what "trouble" your mail account has.

Several of us have a iPhone 6s and are having trouble with hearing and speaking at the same time when using the phone. ? The speakers seem to be too far apart? Are others having this issue? Solutions?

Several of us have a iPhone 6plus and are having trouble with hearing and speaking at the same time when using the phone. ? The speakers seem to be too far apart? Are others having this issue? Solutions?

Not having the problem, don't personally know anyone who is.

Trouble with export and import

I am having trouble with export and import
here is what I did...
exp "'/ as sysdba'" PARFILE=parfile.txt
PAFILE
TABLES=user1.Table1
file=Table1_1006.dmp
LOG=Table1_1006.log
query="where to_char(processeddate,'YYYYMMDDHHMISS') between to_char(to_timestamp('1911-01-01 00:00:00','YYYY-MM-DD HH24:MI:SS'),'YYYYMMDDHHMISS') and to_char(to_timestamp('2011-10-06 16:46:26','YYYY-MM-DD HH24:MI:SS'),'YYYYMMDDHHMISS')"here is my log from export
set and AL16UTF16 NCHAR character set
About to export specified tables via Conventional Path ...
Current user changed to user1
. . exporting table Table1 16019049 rows exported
EXP-00091: Exporting questionable statistics.
EXP-00091: Exporting questionable statistics.
EXP-00091: Exporting questionable statistics.
EXP-00091: Exporting questionable statistics.
EXP-00091: Exporting questionable statistics.
EXP-00091: Exporting questionable statistics.
EXP-00091: Exporting questionable statistics.
EXP-00091: Exporting questionable statistics.
Export terminated successfully with warnings.Then I started importing
/database2/rdbm15> imp "'/ as sysdba'" file=Table1_1006.dmp fromuser=user1 touser=user1 tables=Table1 log=imp_Table1_1006.log
Import: Release 10.2.0.5.0 - Production on Thu Oct 6 19:57:01 2011
Copyright (c) 1982, 2007, Oracle. All rights reserved.
Connected to: Oracle Database 10g Enterprise Edition Release 10.2.0.5.0 - 64bit Production
With the Partitioning, OLAP, Data Mining and Real Application Testing options
Export file created by EXPORT:V10.02.01 via conventional path
import done in US7ASCII character set and AL16UTF16 NCHAR character set
. importing user1's objects into user1
IMP-00015: following statement failed because the object already exists:
"CREATE TABLE "Table1" ("APPROVALTRACEID" VARCHAR2(64), "REQUESTOR"
"EID" VARCHAR2(9), "EID" VARCHAR2(9), "FIRSTNAME" VARCHAR2(32), "LASTNAME" V"
"ARCHAR2(32), "MIDDLEINITIAL" VARCHAR2(8), "TIER" VARCHAR2(3), "JOBTITLE" VA"
"RCHAR2(64), "JOBCODE" VARCHAR2(10), "EMPLOYEETYPE" VARCHAR2(2), "CONTRACTOR"
"TYPE" VARCHAR2(2), "EMPLOYEESTATUS" VARCHAR2(2), "COSTCENTER" VARCHAR2(10),"
" "COSTCENTERDESCRIPTION" VARCHAR2(50), "CONTRACTENDINGDATE" VARCHAR2(8), "A"
"CCOUNTSTATUS" VARCHAR2(2), "LOGINID" VARCHAR2(70), "APPLICATIONGROUP" VARCH"
"AR2(50), "APPLICATIONNAME" VARCHAR2(50), "APPLICATIONID" VARCHAR2(12), "LEV"
"EL1" VARCHAR2(512), "LEVEL2" VARCHAR2(512), "LEVEL3" VARCHAR2(512), "LEVEL4"
"" VARCHAR2(512), "LEVEL5" VARCHAR2(512), "PROFILECODE" VARCHAR2(50), "PROCE"
"SSEDDATE" DATE, "APPROVERMANAGEREID" VARCHAR2(9), "APPROVERMANAGERDELEGATEE"
"ID" VARCHAR2(9), "APPROVERT4MANAGEREEID" VARCHAR2(9), "APPROVERT4MANAGERDEL"
"EGATEEID" VARCHAR2(9), "APPROVERAPPOWNEREID" VARCHAR2(9), "APPROVERAPPOWNER"
"DELEGATEEID" VARCHAR2(9), "PERFORMEREID" VARCHAR2(9), "NATIONALID" VARCHAR2"
"(30), "COUNTRYCODE" VARCHAR2(9), "PASSPORTID" VARCHAR2(20), "DATEOFBIRTH" V"
"ARCHAR2(15), "CITYOFBIRTH" VARCHAR2(15), "VENDORNAME" VARCHAR2(50), "VENDOR"
"MANAGERNAME" VARCHAR2(50), "VENDORMANAGERID" VARCHAR2(9), "VENDORADDRESS1" "
"VARCHAR2(100), "VENDORADDRESS2" VARCHAR2(100), "VENDORSTATEPROVINCE" VARCHA"
"R2(15), "VENDORCOUNTRYCODE" VARCHAR2(9), "VENDORZIPPOSTALCODE" VARCHAR2(9))"
" PCTFREE 10 PCTUSED 40 INITRANS 1 MAXTRANS 255 STORAGE(INITIAL 4076863488 "
"NEXT 1048576 FREELISTS 1 FREELIST GROUPS 1 BUFFER_POOL DEFAULT) "
" LOGGING NOCOMPRESS"
Import terminated successfully with warnings.but I did not get rows to database2
[server1]database2
/database2/rdbm15> sqlplus / as sysdba
SQL*Plus: Release 10.2.0.5.0 - Production on Thu Oct 6 19:59:17 2011
Copyright (c) 1982, 2010, Oracle. All Rights Reserved.
Connected to:
Oracle Database 10g Enterprise Edition Release 10.2.0.5.0 - 64bit Production
With the Partitioning, OLAP, Data Mining and Real Application Testing options
SQL> select count(*) from user1.Table1;
COUNT(*)
 0
SQL> exit
SQL> select * from v$version;
BANNER
Oracle Database 10g Enterprise Edition Release 10.2.0.5.0 - 64bi
PL/SQL Release 10.2.0.5.0 - Production
CORE 10.2.0.5.0 Production
TNS for HPUX: Version 10.2.0.5.0 - Production
NLSRTL Version 10.2.0.5.0 - ProductionEdited by: user3636719 on Oct 6, 2011 5:23 PM

user3636719 wrote:
Thanks for the reply...
Old EXP IMP doesnt have capability to append the row, since you're using 10g use datapump instead. use option TABLE_EXISTS_ACTION=APPENDso my import should be like this
imp "'/ as sysdba'" file=Table1_1006.dmp fromuser=user1 touser=user1 tables=Table1 log=imp_Table1_1006.log TABLE_EXISTS_ACTION=APPEND
Did you look up the command line syntax and control options for imp?
You should make it a habit that whenever anyone - especially a stranger on the web - gives you a bit of code or references a command or init parm or any some such, the VERY FIRST thin you should ALWAYS do is look it up for yourself and see exactly where and how it is used and what it means. That is how you grow beyond having to be spoon fed every little thing and become more self-sufficient.
If you had, you would have seen that there is no TABLE_EXISTS_ACTION option for imp and seen that it is an option for impdp. And realized that exp and imp are NOT the same thing as expdp and impdp.
=================================================
Learning how to look things up in the documentation is time well spent investing in your career. To that end, you should drop everything else you are doing and do the following:
Go to tahiti.oracle.com.
Drill down to your product and version.
BOOKMARK THAT LOCATION
Spend a few minutes just getting familiar with what is available here. Take special note of the "books" and "search" tabs. Under the "books" tab you will find the complete documentation library.
Spend a few minutes just getting familiar with what kind of documentation is available there by simply browsing the titles under the "Books" tab.
Open the Reference Manual and spend a few minutes looking through the table of contents to get familiar with what kind of information is available there.
Do the same with the SQL Reference Manual.
Do the same with the Utilities manual.
You don't have to read the above in depth. They are reference manuals. Just get familiar with what is there to be referenced. Ninety percent of the questions asked on this forum can be answered in less than 5 minutes by simply searching one of the above manuals.
Then set yourself a plan to dig deeper.
- Read a chapter a day from the Concepts Manual.
- Take a look in your alert log. One of the first things listed at startup is the initialization parms with non-default values. Read up on each one of them (listed in your alert log) in the Reference Manual.
- Take a look at your listener.ora, tnsnames.ora, and sqlnet.ora files. Go to the Network Administrators manual and read up on everything you see in those files.
- When you have finished reading the Concepts Manual, do it again.
Give a man a fish and he eats for a day. Teach a man to fish and he eats for a lifetime.
=================================

TO ALL THOSE HAVING TROUBLE WITH ICHAT AND AIM ON MACBOOKS

I've had a lot of trouble with AIM and iChat on my new Macbook, but I believe I've figured out the answers to all the problems I and others have encountered.
Firstly, for those who's AIM continually crashes and displays the message "The application AIM unexpectedly shut down," my answer to your problem is too many sent messages. Watch the bar in the bottom left of your chat window, when it reaches red, your application will probably shut down.
Secondly, for those experiencing difficulties with iChat, it's most likely a problem with communitcation between your wireless router and your computer. Try these steps:
1. From the Apple menu, choose System Preferences.
2. From the View, choose Sharing.
3. Click the Firewall tab.
4. Click New.
5. From the Port Name pop-up menu, choose Other.
If you have a Macbook, you'll probably have a TCP Port Number Bar and a UDP Port Number Bar. Try these steps:
1. In the TCP Port Number(s) Bar, type: 5190, 5298
2. In the UDP Port Number(s) Bar, type: 1024-5219, 5221, 5223-65535
3. In the Description Bar, type: iChat AV
4. Click OK
5. Click Start above the window with your firewall settings, and make sure the box next to iChat AV is checked
6. Relaunch iChat
Good Luck! I hope this solves some of the problems that people have been encountering.

Rob
My Linksys is the WAG54G, which might be different from your WRT54G. Currently, UPnP is disabled and the Router ports are a bit of a mystery, because they're forwarded to an IP address that's outside of the current DHCP Address Range! Once I got it working, I was reluctant to change it even though it looked anomalous.
The Firewall is on, with the iChat ports open that I listed in the previous post.
My two regular buddies are my sons, who both use Trillian Pro on a Windows machine. Works pretty well despite occasional freezes or garbled sound.
Hope you get sorted soon.
Dave

I am having trouble with safari and most apps shutting down when I'm in the middle of stuff what do I need to do to resolve this?

I am havering trouble with safari and apps shutting down on me all the time what can I do to resolve this problem. Thanks :-)

Make sure you have enough free space on your iPad. With iOS 7 it is recommended that you have 15-20% of the storage space on the device free. For a 16 GB device that is 2.4-3.2 GB free. For a 32 GB device that is 4.8-6.4 GB free. For a 64 GB device that is 9.6-12.8 GB free.
Also try a reset. Press and hold the Home and Sleep buttons simultaneously until the Apple logo appears. Let go of the buttons and let the device restart. See if that fixes your problem.

I'm Having trouble with OWA and Certs after the Rollup 7 for SP3 installation. any idea? update 2961522-

Hi, everyone.
I'm Having trouble with OWA and Certs after the Rollup 7 for SP3 installation. any idea? update 2961522-
after running get-OWAVirtualDirectory or test-OWAConnectivity i'm getting a message that says "OWA it's Orphan, No Metadata information can be found."
I only have the OWA users impacted.- anywhere users, and ActiveSync are working well.-
Thanks,
Fabian Alberto Campo
MCT-MCSA 2012-MCITP365-MCTS
Fabián A. Campo H. Consultor tecnico @ IXO Ltda. MCT MCP MCTS MCSA HP-APS Cra. 67 No. 167 – 61 of 303 Bogotá, Colombia

Hi Fabian,
Is there any error code when user access their mailbox on OWA. Please confirm if there is no results returned in EMS when you run Get-OWAVirtualDirectory cmdlet. Also check whether there is any Event Logs related to OWA in Exchange.
In IIS manager, make sure the OWA virtual directory is listed in the Default Web Site. In EMC, we can navigate to Server Configuration > Client Access, select server and turn to Outlook Web App tab. Then we can click Reset Virtual Directory in the right
Actions pane to reset OWA virtual directory.
Additionally, please restart IIS service by running iisreset /noforce from a Command Prompt window.
Regards,
Winnie Liang
TechNet Community Support

Trouble with edit and develop after november 2013 release?

Hi,
I can not use edit and develop after release November 2013.
I am a user from Sweden and wonder if it only hit European data center?
The language has also changed from Swedish to English in the modules.
I can not access the following in Site Settings:
Admin users
Mobile support
Secure Domain redirect
Beta features
Does anyone have the same problem?
Regards André

Hi Florin
There is no errors in the browser. I tested Chrome, Safari, Firefox.
I sent a video to your colleague Silviu Ghimposanu (Adobe Business Catalyst Support)
He can give you more information. I submit tickets. Ticketsnr 60092, 60085
Maybe you can solve this together.
Regards André
20 nov 2013 kl. 12.17 skrev Florin Carlig:
Re: Trouble with edit and develop after november 2013 release?
created by Florin Carlig in Business Catalyst - View the full discussion
Hi Andre,
Can you please record a quick video with the errors you might have in your browser, in the browser's console?
Here's what I want (a video I did in Chrome): http://screencasteu.worldsecuresystems.com/Florin/2013-11-20_1306.swf
You can use Jing to record this kind of videos: http://www.techsmith.com/jing.html
Thanks and regards,
Florin
Please note that the Adobe Forums do not accept email attachments. If you want to embed a screen image in your message please visit the thread in the forum to embed the image at http://forums.adobe.com/message/5857868#5857868
Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page: Re: Trouble with edit and develop after november 2013 release?
To unsubscribe from this thread, please visit the message page at Re: Trouble with edit and develop after november 2013 release?. In the Actions box on the right, click the Stop Email Notifications link.
Start a new discussion in Business Catalyst at Adobe Community
For more information about maintaining your forum email notifications please go to http://forums.adobe.com/thread/416458?tstart=0.

I have an iPhone and just goy I pad but no computer I'm trying to synch them together but having trouble with iCloud and I can't seem to subscribe for iTunes match from either devise

I have an iPhone and just goy I pad but no computer I'm trying to synch them together but having trouble with iCloud and I can't seem to subscribe for iTunes match from either devise

You first have to subscribe to iTunes Match through iTunes on your computer and have your music library in iTunes uploaded/matched before you can enable it on your iOS devices (see http://www.apple.com/itunes/itunes-match/). Without a computer you won't be able to use iTunes Match.

I'm having trouble with purchased and every time I tried to install something it won't let. Me

I want to know that can I install something with out credit card

Contact iTune Support
https://ssl.apple.com/emea/support/itunes/contact.html

Anyone having trouble with Splashtop and Maverick?

Splash top will not run since installing Maverick. I have uninstalled and reinstalled, but still no go. Anyone else?

I've been having trouble with this since I upgraded to iOS 7.0.2! Logged on tonight to see where I could log the problem with apple to get to fix in the next update! Seen on Facebook that others having same issue.
I've also had a problem that when I put phone in to airplane mode it isn't reconnecting to the network afterwards!

Trouble with Windows7 and Gigabit link on Cisco 3560X switch

Hello,
In my company, we are using Cisco IP Phones 7945G (with 2 gigabit network ports) and Cisco 3560X-48P (1GB ports) switches for our users.
Our client computers are running on Windows 7 SP1 (64bit - Enterprise edition) and are connected behind the IP Phone. We use a "Boradcom
Xtreme Gigabit" onboard network card on the computers. All ports (on the switch site and IP Phone side) and on the network card of the computer are configured in "auto negotiation". Duplex and speed are set to "auto".
We tried now to deploy a new engineering software and we are facing a very strange problem. This means that the engineer software fails to download some files from the server. We are using a flat network, all the servers and computers are on the same network segment with no firewall inbetween.
The firewall and Anti-virus on the computers are configured to allow all incoming/outing connections.
To troubleshoot, I tried to change all the network cables but I still get same result --> download fails.
I connected the client computer directly to the Cisco 3560X switch, without the IP Phone and I get the same result.
I installed a separate network card from INTEL (Intel PRO1000 PT) but I get the same result.
As last test, I have connected to same client computer directly to a Cisco 2960-8TC switch (100Mbit; auto negotiate) and here is working fine. The software successfully downloads all the files from the server.
If I connect the computer behind the Cisco 7945 IP Phone, set the speed and duplex of the PC-Port on the Cisco IP Phone 7945G to "100MBit/full duplex" is also working fine.
Is there any know issue with Windows7 and Gigabit network connections?
Do I need to set any Registry key on my Windows 7?
The firmware version of my Cisco 3560X-48P switch is 12.2(53)SE2; do I need to update it?
The firmware version of the IP Phone 7945G is 9.2.1.
Thanks in advanced for your help.
Marc Hoffmann

Hello, Thanks for your answers. First of all, I have updated the firmware of my Cisco Catalyst 3560X-48P switch to the version 12.2(55)SE5. Unfortunately, this did not solve my problem. As second step, I ran an TDR test on my 3560X switch but I do not get any result. The "Pair status" always says "not completed". Even if I wait for 5 minutes, the status remains at "Not completed". Am I doing something wrong ? To do the TDR test, I use the commande "test cable-diagnostics tdr interface gigabitEthernet 0/XY". For your information, the port gigabitEthernet 0/XY is in a "Connected" status when I run the "show int status" command. Jeff, I think there is no issue on the server side, because if I connect my workstation on a 100MB switch (example Cisco Catalyst 2960-8TC-L) the application works absolutely fine. Also, if I run the application locally on the server, it works fine. As next step, I will connect the workstation directly on our backbone switch and try the same test. Is there perhaps any Registry key in our Windows7 which could cause this trouble? If you have any other ideas or options, please let me know. Thanks a lot, Marc Hoffmann

USB2.0 Install Troubles With WinXP and KT3 Ultra2?

Similar Messages

Maybe you are looking for