USBTMC device does not show up in MAX.

I have a USB device that will not show up in MAX.  When I plug the device into the computer, it is recognized as a USBTMC device and Windows chooses NiUsbTmc.sys as the driver.  I believe it also uses niusbtmc.inf and niusbtmc.pnf.  After going through the process and rebooting, the device shows up in the Windows device manager as a USB Test & Measurement device.  When I open MAX, the device does not show up in the device tree, nor can I seem to find a way to communicate with it.  So I uninstalled the device, removed the files above to a temp directory, rebooted, and then created a new inf file using the VISA driver wizard.  After going through that whole process, rebooting and then plugging the device back into the computer, I directed Windows to use the new inf file.  The device now shows up in the Windows device manger as a NI-VISA device and the driver is NiViUsbK.sys.  I open MAX back up and the device is nowhere to be found.  I tried using the VISA Interactive control to find the device, but no luck.  What step or steps am I missing?

Just plugging the instrument in should have made the device appear as USBTMC in MAX and using the driver wizard is not correct. I don't understand why it didn't show up in MAX with either method though. I've only a small amount of experience with USBTMC but have used the wizard a lot for internally developed USB instruments and they have always appeared in MAX. What version of VISA are you using? The latest version is 4.1 that can be downloaded from http://digital.ni.com/softlib.nsf/websearch/B1A783​7FFFD2826E8625729100689D3C?opendocument&node=13207​....

Similar Messages

  • Yesterday I  reset my settings on my  iphone 4 to correct another problem. Today I am unable to connect to itunes to sync my phone. The device does not show up on the screen. What can I do?

    Yesterday I reset my settings on my iphone 4 to correct a problem. Today I am unable to connect to itunes to sync my phone. The device does not show up on the screen. What can I do?

    Best practices says plug the USB cable into the computer, then plug the 30 pin connector into the iPhone.
    If everything is working correctly, you should be able to plug the iPhone in at any time. Before or after opening iTunes.
    Depending on what settings are selected in iTunes, the program may or may not automatically open when you connect the device.

  • I can't synch my iPhone with iTunes because the device does not show up in a device window when I plug it in...it's missing in action and thus I'm not able to add any content from the iTunes to my iPhone, e.g. podcasts

    I can't synch my iPhone with iTunes because the device does not show up in a device window when I plug it in...it's missing in action and thus I'm not able to add any content from the iTunes to my iPhone, e.g. podcasts.   All the instructions on synching start with "find your device in the device window".  But what if you have no device window?

    Missing "message" from above: The iPad "DGMTR" is synced with another iTunes library on DGMTR's MacBook Pro. Do you want to erase this iPad and sync with this iTunes library? An iPad can be synched with only one iTunes library at a time. Erasing and syncing replaces the contents of this iTunes library.
    I thought the libraries were the same.

  • TS1424 Apple Mobile device does not show up after installing 10.0.7.21

    Receive message "Apple Device not started". Apple Device does not show up in Adminstrative Tools, Services. Windows 7 64bit, IOS6.0.1.

    For general advice see Troubleshooting issues with iTunes for Windows updates.
    The steps in the second box are a guide to removing everything related to iTunes and then rebuilding it which is often a good starting point unless the symptoms indicate a more specific approach. Review the other boxes and the list of support documents further down the page in case one of them applies.
    Your library should be unaffected by these steps but there is backup and recovery advice elsewhere in the user tip.
    The section Install missing components has advice on breaking down the iTunes installer into the individual .msi files which might prove useful if a component such as Apple Mobile Device Support won't install normally.
    tt2

  • I have just updated iTunes on my laptop, and now when i plug my iPhone in, the device does not show up in iTunes. I have tried multiple wires and uninstalling and re-installing iTunes. What do i do?

    I've just updated my iTunes on my laptop
    And when i plug my iPhone in, nothing happens and the device does not show up in iTunes
    I have tried numerous cables, uninstalling and re-installing iTunes and searching for devices on iTunes
    And i still have no luck
    help!

    Pick the appropriate one of these for advice:
    Windows - http://support.apple.com/kb/ts1538
    Mac - http://support.apple.com/kb/ts1591

  • HT201412 My iphone stopped working, and and conneted to itunes but my device does not show in itunes also....please help

    After upgrade to ios 6, iphone 4 is not wroking, It suddenly stops responding to any actions. Today it totally stopped and is nothing working. Connected to itunes and the device does not shows up. Please help

    Please turn off your caps lock.
    All caps indicates shouting, is considered rude and is difficult to read.  Many will not read such posts.
    If you are unable to restore your iphone then try this:
    iOS: Unable to update or restore

  • I am running Lion 10.7.2 and I have an external drive hooked to my time machine. I can't rename folders and when trying, I get an error code 8076. The checkbox "ignore permissions for this device" does not show on volume info. Help please???

    I am running Lion 10.7.2 and I have an external drive hooked to my time machine. I can't rename folders and when trying, I get an error code 8076. The checkbox "ignore permissions for this device" does not show on volume info. Help please???

    The TIme Machine volume does not have that checkbox.
    I think the issue is with your Finder...
    Go to Finder "Go" menu hold the option key and choose Library. Then go to Preferences trash these files:
    com.apple.finder.plist
    com.apple.sidebarlists.plist
    Then, restart, or log out and in again.
    (You will have to reset a few finder prefs the way you like them.)

  • TS2634 When I open iTunes using PC, the device does not show up anywhere

    The device does not show up anywhere.  This is happening for iPhone and iPad.  Thoughts?

    Hi Friednhook,
    If you are having an issue with your devices not being recognized in iTunes on your Windows PC, you may find the following article helpful:
    iOS: Device not recognized in iTunes for Windows
    http://support.apple.com/kb/ts1538
    Regards,
    - Brenden

  • W520: Unable to boot from USB - device does not show up in boot menu

    I have a W520, and I am trying to boot from a USB key. The USB key is bootable, my old T61p boots just fine from it, and so does another computer I tried.
    The W520, after pressing F12 on power on, immediately shows the Intel PXE agent and then some blue boot menu, which only shows hard drive and LAN as available boot options.
    I have tried all three USB ports but the results are always the same - the USB device does not show up. Is there any trick or BIOS setting to enable boot from USB?
    Thanks,
        CS 

    Hello Neil
    Thanks for getting back to me
    The issue was that the usb drives were disabled in the bios from the  Startup menu.
    To enable
    1. Enter bios
    2. Select boot
    3. If you do not see the boot device you require use the down cursor key until the "Excluded from boot priority order" becomes visible.
    4. Select the device you require (in my case USB HDD)
    5. Save and exit.
    You can now boot from a usb stick and install the Linux distro of your choice :-)
    Cheers

  • ITunes recognizes my device but the device does not show up for me to work with.  Any idea where I go to access to device in iTunes.  Going to File/Device is greyed out.

    iTunes recognizes my device but the device does not show up for me to work with.  Any idea where I go to access to device in iTunes.  Going to File/Device is greyed out.

    I think this article will help you.

  • "Device" does not show in iTunes to start syncing when I plug in my iphone

    "Device" does not show on my latest itunes on my MacBookPro, using Mountain Lion to sync my Iphone,how can I get it to show up?
    Thanks

    Hi Chiquita,
    Do you have your Sidebar showing? Go to the top of the screen and click on View, then click on "Show Sidebar".
    See if that resolves your issue.
    Cheers,
    GB

  • My new ipad will not sync with itunes.  the device does not show up in itunes

    my new ipad will not sync with itunes.  the device does not show up in itunes.  I am on a Windows system

    Do you have the absolute latest version of iTunes downloaded?  If your iTunes software has not been updated in some time, your iPad will not be recognized.  With iTunes open, click on Store at the top.  Check for available downloads and if there are any, download them.  Once you've verified you have the latest software, connect your device again, and it should be recognized.

  • Device does not show up on i tunes

    new i phone 5 device does not show up on itunes. wanting to sync new device

    Have you used any other iOS devices with the computer?
    Try reinstalling the latest version of iTunes.
    If that doesn't take care of it, one of these Apple docs should help ya out:
    iOS: Device not recognized in iTunes for Windows
    iOS: Device not recognized in iTunes for Mac OS X

  • I have a MacBook using Snow Leopard 10.6.8 and iTunes 11.0.1.  When I tether my new iPod Nano, the icon shows on my desktop, but the device does not show up on iTunes.

    I have a MacBook with Snow Leopard 10.6.8 and iTunes 11.0.1.  When I tether my new iPod Nano, the icon shows up on my desktop, but does not show up under devices in iTunes.  The Nano says it is connected and synching, but I cannot download music if it doesn't show up under devices.

    Hi,
    Have you managed to solve this problem? if yes, please highlight how you solved it...i'm facing same problem with my new Iphone 5S but udner Windows, thanks.

  • CJC channel does not show up in MAX

    Greetings,
        I have an SCXI 1124 that I am reading in 32 TC's with.  When I try to configure it for CJC internal under MAX for physical channel it does not show up as described in "DAQmx Acquire CJC Temperature".  In that document the CJC physical channel should show up as a string similar to SC1Mod1/_cjcTemp but all I see under MAX under the 1124 is ai0-31.  I know this should be obvious but could someone shed some light on this and explain my oversight.

    Hi teslac,
    The SCXI 1124 is an Analog Output module. Could you mean an 1121 or 1125 possibly?
    Also, are you scanning the cjc temp channel along with the thermocouple channels? There are some SCXI modules that have to scan only the cjc temp channel without any other channels. You can find this information int he KnowledgeBase article below.
    How Can I Address and Use Cold Junction Compensation (CJC) with SCXI Modules?
    Hope this helps!
    Robert R. | Applications Engineer | National Instruments

Maybe you are looking for

  • Can I Create a New User Account and Move Existing Account ???

    Lion was reinstal. I'm suspecting issue with one user account. Can I creat a new user account and move all my files to that new user? What are the impact? How about permissons on this files? What about the Library Folder? Thank you for your help and

  • External drive refuse to show up in network

    I have just bought a Verbatim 3TB external harddrive (http://www.verbatim-europe.co.uk/en_1/product_store-n-save-superspeed-usb-3-0-de sktop-hard-drive-3tb_9566_0_35770__12692.html?con=39) It works fine plugged directly into my retina laptop but refu

  • Flickery transitions in iDVD slide show

    I have burned two disks now using iDVD and had no trouble but I do have a question about transitions in slide shows. On the first disk I used a slide show (8 minutes, 99 images) with the "fit to music" option and the "use safe area" option for the di

  • JDBC Adapter - Update SQL Statement - Timestamp

    Hi All, I'm using a JDBC Sender channel to bring information from a database, when I bring the data I want to UPDATE a field inserting the date and time (timestamp) when you got the info. Sender Communication Channel: JDBC Query SQL Statement:  SELEC

  • Error in changing the number range from the external to the internal no.

    Dear all,              Here is the error found when using the T-Code PA30  for hiring an employee. while changing the number range from external to internal using Tcode  PE03, the error found was ' could not find interval for the number range' Can an