Use of adobe on more than one device

I have been using creative design 5 on a normal pc for some time, I now want to also use on my mac laptop. Both machines will not be used at the same time. How can this be done?

It cannot be done. Your license is only good for one platform and you cannot purchase a new copy for the Mac or swap it either.

Similar Messages

How do I use AE to allow more than one device with my cable modem?

I connected by AE to my cable modem at my house in Japan and it works fine on "bridge mode," but only for one device at a time (this laptop, but not my iPod Touch, or vice versa). As soon as I connect a new device, it will kick the other one off. It seems that my cable modem here will only allow one device. Is there a way that I can use my Airport Extreme to allow more than one device and not have to pay the Internet provider extra for multiple IP addresses? How do I go about this? Do I select "share a public IP address" or do I select "distribute a range of IP addresses?" I tried these options but obviously wasn't doing it correctly, because then I lost the connection for everything... Thanks!

It would be best if you "hard reset" the Airport Extreme to clear out the old and conflicting settings and then reconfigure it again.
Hold in the reset button until you see the amber light begin to blink more quickly. Keep holding for another 3-4 seconds when you see this and then release the reset button. That will get the Extreme back to the original starting point.
After you have powered the modem back up after the full reset, you will need to reconfigure the AirPort Extreme again. If you are using he guided setup in AirPort Utility, you will choose the option to "create a wireless network" during the setup.
If you are using the Manual Setup, the Wireless Mode will be "Create a wireless network" and the setting for Connection Sharing would be "Share a public IP address". Adjusting the Connection Sharing setting would be the last thing that you do before you click Update to save settings.
Here, I am assuming that you have a simple cable modem (it will have only one ethernet port), correct?

How to authorize more than one device on my adobe digital editions Ebook reader

I have a computer, iPhone and iPad, and can't read a downloaded ebook (EPUB) on more than one device at a time. If I try to open the item on my Overdrive account with a device other than the one I originally used when I downloaded the ebokk, it gives me an error code "Fullfill 2004. This license has already been fulfilled by another user". When I contacted Overdrive Media they explained that I need to contact Adobe to authorize my various devices to have access to my Overdrive account which utilizes Adobe digital editions 4.0
Please provide info on how to authorize my additional devises to have access to downloaded e-books on my overdrive account

Please authorize your devices with same credentials in order to read the book across devices.
thanks

How to use more than one device under same apple ID?

How do you you use more than one device under same apple ID? say for facetime?

You don't. One Device and one Apple ID.

I want to use Back to my mac. When I try to turn it on, it says "Back to My Mac may be slow because more than one device on your network is providing network services. Turn off NAT and DHCP on one of the devices and try again." How do I fix this?

Not sure if I am doing this right. This is my first time in the support community.
I imagine what I put in my heading was supposed to go in here.
I want to use Back to my mac. When I try to turn it on, it says "Back to my mac may be slow because more than one device on your network is providing network services. Turn off NAT and DHCP on one of the devices and try again. See the documentation that came with your device for information about turning off network services"
Does anyone know how I do this? I contacted my ISP (Telus in Canada) and they did not know anything (not that they usually do).

Why do ISPs insist upon making things so difficult for their customers?
If you cannot get them to understand that you would prefer to use your own router over their piece of cheap junk, perhaps the information in the following will be useful:
http://keithbalomben.wordpress.com/2012/03/29/telus-actiontec-v1000h-hacks-and-i nformation/
Scroll down to DHCP Settings
You will need to log in with proper "technician" credentials. They are provided in the above link as
Username: tech
Password: t3lu5tv
... but these may or may not work. Try it, and if you cannot get anywhere at least now you know what to ask Telus to do in return for your business.

More than one device is using the same email. Help!

I use to have an Iphone in the summer but now its disconnected and i left my apple ID signed into my Imessage. I gave this phone to mom and now i have a new Iphone with the same Apple ID signed into my imessage. The other phone is still disconnected but I am 100% sure she is recieving my messages and I can't get a hold of the other iphone. Is there something i can do to my current iphone so she can stop recieving the messages? Will changing the email that i recieve messages at help? or changing the password to my Apple ID? Please help.

I will restate what is happening.
Network:
House; internet to wireless router BEFW11S4 (wireless=off, DHCP=on), 5 computers wired in plus one wireless bridge WET11.
The bridge talks to a second wireless router in the office (100 feet away). Wireless=on, DHCP=off, different address! There are 3 computers there.
This has worked for years! There is a third wireless router with wireless=off, DHCP=off and with a different address that is used for a hub.
Now people come with laptops and want to use wireless. If any of the routers have wireless=on the network crashes with “more than one device with same address”.
To troubles shoot; I reduced the network down to 3 pieces. Router in house, 1 computer and the WET11 bridge. All have fixed addresses! If I set wireless=on (router), then the bridge and the wireless router communicate wireless and communicate via cat-5. The network crashes.
For a test; I connected all three routers together with wireless=on then the bridge talks to all three via wireless and via cat-5 wire. I tried WEP with different pass phrases on each router and different frequencies. My bridge will talk to all routers it can find on any frequency with any pass phrase. It may not be able to pass files but it can find all the computers.
I believe the router wakes up and sees;
its self 192.168.123.254, computer 192.168.123.100 and a bridge 192.168.123.225
The bridge sees a new network with:
Router 192.168.123.254, computer 192.168.123.100 and bridge 192.168.123.225
And that bridge sees a new network with:
Router 192.168.123.254, computer 192.168.123.100 and bridge 192.168.123.225
“feed back”
I really want the bridge to talk to router 192.168.123.253 (office) but not talk to .254 on the same switch/hub (house).

Is there a stereo bluetooth headset that can pair with more than one device at a time?

Is there a stereo bluetooth headset that can pair, i.e. multipoint, with more than one device at a time?
Are the MacBook and iPhone 4 capable of multipoint bluetooth technoloagy?
The goal is for my wife to be able to watch her Korean TV soap operas on her MacBook and still receive a call on her iPhone 4 via a stereo bluetooth headset.
I was looking at the Motorola S10-HD but after further review saw that it only pairs with one device at a time.
Appreciate any and all input. My Googling has returned no results.
Rick

TeslasBB wrote:
pairing my BB8330 with my blue tooth earphone(TM:jawbone) and my microsoft sync thats in my car simultaneously? if i pair with the car, will i have to pair my jawbone all over again?
You can only pair one device at a time to your 8330, or any other phone for that matter. The "pairings" are saved to the phone, you can use one or the other and you won't have to pair it again. Once you turn your bluetooth device on and the phone is on, they will find each other again.
Hope this helps,
John
Stevie Ray! 1954-1990
** Don't forget to resolve your post with the accepted solution.

Can you get an Apple ID for corporate use to associate with more than 10 devices?

Can you get an Apple ID for corporate use to associate with more than 10 devices?

I don't believe you can. The usual model for iOS app distribution is for each device to have a unique Apple ID and for apps to be acquired separately, either via codes from the Volume Purchase Program or individual purchase through the iTunes Store. The licensing from the iTunes Store doesn't allow an app to be installed on more than one device unless all the devices are being used by a single person, so you legally cannot install one app on multiple corporate devices in the circumstances most businesses use.
Regards.

HT1420 Can you have more than one device with a different Apple ID authourized to the same computer

Can you have more than one device with a different Apple ID authourized to the same computer

I think you are using the same Composition Class on both project. On the properties tab, you can change this number (e.g.: EDGE-1637270).

Airport disconnects when there's more than one device

I've got a really weird problem.. I have an Apple Airport Extreme 802.11n 3rd Generation. Software version 7.6 When more than one device connecrts to the base station it will disconnect everyone and then all devices will go into a connect/disconnect loops. Rapidly. This occurs only with wireless device. I watched the radar on my iPhone (5.1), Macbook running Snow Leopard, Macbook Air running Lion, and iPad 2 (5.1) blinking on and off, on and off. The only way to resolve this is to just have ONE person connect at a time.
Things I've tried:
1) Updating all software on all devices
2) Updating Airport firmware
3) Reboot and then restoring factory settings on the Airport when the reboot didn't work
4) Turning off encryption (WP2)
5) Making sure there are enough IP's for all the devices, turning off robustness, making sure the router is visible.
Because I know someone will ask this: The Airport sits atop a credenza in the open air. Nothing on, around, or above it. It's been in this position for months with no problem. It's not overly warm to the touch and I even used compressed air to blow out the vents (just in case) when this problem began.
I read once upon a time that the router gets a cache built up and that can cause these types of issues, but I have no idea how to delete said cache or even if it exists. It's just odd this only happens when more than one wireless device tried to connect to the network.
Thoughts?

I've resolved this! For some odd reason Apple won't let me denote this so I'm adding this reply. Turns out the problem was POWER related. The Airport was plugged into a power strip with several other devices. I unplugged all of those leaving just the Airport and the problem has not returned. If I add on all the devices, regardless of the power strip used, the problem returns. So it appears the Airport was just not getting enough power.
I've got it on a UPS now and the problem has not returned.

Why won't my Time Capsule allow me to connect more than one device to the network at a time?

Ok here is the shortest story I can come up with...
Several months ago lightening struck my house and ruined the power cord for my old AIR PORT EXTREME....after replacing the power cable my wireless network began to prohibit more than one device at a time to connect to the wireless network.
I replaced that network with a new TIME CAPSULE and it is doing the same thing. I took my old AirPort Extreme to my work and it works like a charm. My ISP says it is an Apple problem but I have had the same settings both at home and at work. Work is great, multiple devices connect but home is one at a time and in order to connect ANOTHER device I have to power down one, and reboot the router and fire up the device I wish to connect.
Any suggestions?

I am running off a Fiber line....the unit that is a battery back up and appears to be a modem as well is called CyberPower CS24U12V-NA3
Techincally, there is no "router" in my house, there is a LOCKED control box outside, a battery back up module in the garage that shows battery life and connection, then a cat5 outlet in my laundry room..All of which was installed by my ISP.
I am using a 2TB Time Capsule running DHCP in Bridge Mode. I can't find the software version but updated it while installing it within the last two months.
Under Network Tab
Enable NAT Port mapping is checked
Under the Wireless Tab
we have a 5ghz Network
Radio mode is set to: 802.11a/n-802.11b/g/n (Automatic)
2.4 GHz is Auto
5 Ghz is Auto
I hope this helps....

More than one device connected?

I am testing out a project for a mobile device and when I package the apk and attempt to launch it on my phone, I get an error message sying that it can't be done because I have more than one device connected. I only have one device connected.
I've tested this project before n my phone and it launched as it was supposed to, but I added a document class to the project and think that might be causing the problem. Previously, I added all of my action script to a keyframe on the timeline, and everything worked fine.
I'd like some feedback as to whether or no the document class issue is the likely problem and how to get around it. If that's not the problem, I'd like to what what might be going on. As always, any help is greatly appreciated. Thanks.

using a document class is not the problem (though your document class may be a problem if it has errors).
use a file explorer to see if your computer lists more than 1 connected device. or restart your computer to reset its external connections.

How can i use my iphone with more than one itunes

how can i use my iphone with more than one itunes

Sync iPod/iPad/iPhone with two computers
Although it isn't possible to sync an Apple device with two different libraries it is possible to sync with the same logical library from multiple computers. Each library has an internal ID and when iTunes connects to your iPod/iPad/iPhone it compares the local ID with the one the device normally syncs with. If they are the same you can go ahead and sync...
I have my library cloned to a small 1Tb USB drive which I can take between home & work. At either location I use SyncToy 2.1 to update the local copy with the external drive. Mac users should be able to find similar tools. I can open either of the local libraries or the one on the external drive and update the media content of my iPhone. The slight exception is Photos which normally connects to a specific folder on a specific machine, although that can easily be remapped to the current library if you create a "Photos" folder inside the iTunes Media folder so that syncing the iTunes folders keeps this up to date as well. I periodically sweep my library for new files & orphans with iTunes Folder Watch just in case I make changes at one location but then overwrite the library with a newer copy from the other. Again Mac users should be able to find similar tools.
As long as your media is organised within an iTunes Music or Tunes Media folder, in turn held inside the main iTunes folder that has your library files (whether or not you let iTunes keep the media folder organised) each library can access items at the same relative path from the library folder so the library can be at different drives/paths on different machines. This solution ensures I always have adequate backups of my library and I can update my devices whenever I can connect to the same build of iTunes.
When working with an iPhone earlier builds of iTunes would remove any file not physically present in the local library, even if there was an entry for it, making manual management practically redundant on the iPhone. This behaviour has been changed but it will still only permit manual management with a library that has the correct internal ID. If you don't want to sync your library between machines on a regular basis just copy the iTunes Library.itl file from the current "home" machine to any other you want to use, then clean out the library entries and import the local content you have on that box.
tt2

How to set permissions to allow reading on more than one device

Our base permissions restrict reading to one device for 365 days with print 1 page and copy 1 page limits. For a new book we're adding to our online library, we want to allow people to read on more than one device, with a defined expiration date (January 15, 2012) and no printing and no copying. (The "more than one device" restriction is intended to allow users to transfer the book to iTunes and read it in Bluefire Reader.)
How do we set permissions for this new book? In particular, what Read settings for devices do we use? No selection? The options in the ACS Console are not clear to us (i.e., the choice between A Single Device and Specific Device Type) and the manual doesn't offer an example. ... I'm guessing the selections should be none -- i.e., do not specify any device setting. Yes?
Any help would be appreciated.
Jim Lyons

What I understand your current side restrictions to be (best if they are in a distribution right rather than base permission btw)
<permissions>
<display>
     <device />
     <duration>31536000</duration>
<display>
<print>
<count initial="1"/>
</print>
<excerpt>
    <count initial="1"/>
</excerpt>
</permissions>
What I think you want
<permissions>
<display>
     <device />
     <duration>31536000</duration>
</display>
<display>
     <deviceType>mobile</deviceType>
     <until>2012-01-15T00:00:00-8:00</until>
</display>
<display>
     <deviceType>tethered</deviceType>
     <until>2012-01-15T00:00:00-8:00</until>
</display>
<print>
<count initial="1"/>
</print>
<excerpt>
    <count initial="1"/>
</excerpt>
</permissions>
(these are looking at the raw permissions rather than the dialog in the admin console)
Which I would describe as allow viewing on the device which fulfilled the content for one year, and in addition allow viewing on any mobile or tethered device (Bluefire Reader iPad app, android app, Nook Color, etc...) until Jan 15, 2010 at midnight PST. One print and one copy is allowed (and can only be used on the device that fulfilled the content).

How can i use Itunes to update more than one IPad with more than one owner

How can i use Itunes to update more than one IPad with more than one owner? I own an IPad and my wife owns an IPad. I want to use my system to update both IPads. We have different Apple Accounts and different applications. Is this possible?

Of course, that is too easy. I am such a bonehead.

Use of adobe on more than one device

Similar Messages

Maybe you are looking for