USE of CF 6004 with HP IPAQ 5550

Hello
Could someone tell whether we could use CF-6004 with HP IPAQ 5550 PDA? as it looks that the size of the card is a bit larger to fit in the memory card slot.
thanks
Sam

Hi Sam,
Natively you can not use the CF-6004 with the HP IPAQ 5500, as the IPAQ does not have a Compact Flash (CF) slot. However for the IPAQ 5500 you can buy a CF sleeve, I have seen some on eBay, but you should be able to get a HP IPAQ CF Sleeve from a more reputable location.
I hope this answers your question
Regards
JamesC
NIUK and Ireland

Similar Messages

Using the 6500c with HP iPAQ

I need to use the modem from the 6500c to connect to the Internet with the iPAQ.
The correct parameters are entered on the telephone which work with a telephone from Ericsson.

The Bluetooth settings on the iPAQ are
General Profile default
Accessibility Name WM My Name
Address 00:121:31:CA:80
(Use PocketPC device name for Bluetooth
Accesibility Allow other devices to connect
- Paired devices only.
Services File Transfer; Info Exchange; Serial Port; Personal Network Sever.
Service Settings Enable Service On
Authorisation req. On
Authentication(passkey) req . On
Encryption required. On
Switching on Bluetooth the iPAQ I see that I have contact with the 6500c. I have set the parameters for a connection with SFR which uses the channel *99***1# (given by SFR and which works with the Ericsson but using *99***3#) I have then added the dial-up modem command AT+CGDCONT=1,"IP","websfr"
I have spoken both with SFR and Nokia (Service Centre,) and no one has an idea on how this problem can be resolved.
It appears that there is a lot of interest with the same problem on the 6500 slide.
Thanks for your help

Issue with hp ipaq 614c and cisco ap

Hello. I tried to connect an ipaq 614c to a cisco ap1131 using wpa-psk tkip with no success. The ipaq connects without any problem to other access points including linksys. I've tried odysey client and I get the message: waiting for keys. The event log of the AP says: Packet to client reached max retries, removing the client. I am able to connect with other models of ipaq to the ap. Anyone know what the problem might be? I also tried disabling QOS but the result is the same.

Is the ssid only config for 1 security policy? I had an issue one time where the SSID was config for both WPA and WPA2 and i had issues. It wasnt till i selected just a single security policy that it worked.
You may want to try a real simple key at first. Try connecting it to an open network. Start 'unpacking' it so to speak...
You may see more info if you go into the CLI of the controller and debug the client. Also, if you have a layer 2 analyzer (AirMagnet or Peek you may see something of interest...)

Is iPaq 5550 supported?

We are just in a testing phase with the following environment:
- ZfH 5.1
- Windows NT 4.0 Desktop with serial cradle
- ActiveSync 3.7
- iPaq 5550
After installing the ZfHProxy on the Desktop and connecting the PDA, a
message appears on the PDA saying something like "ZfH Client installation
unsuccessfull". After disconnecting an reconnecting the PDA I get the
message "ZfHClient already installed...".
Is this environment supported or are there some known issues with this PDA?
Olaf Brandt

Something I just found out:
there seems to be a localized (german) version ZfH 5.1.250.
I only have 5.1.162 english.
Can someone post the link where to download the newer version?
Many thanks
Olaf Brandt
> We are just in a testing phase with the following environment:
>
> - ZfH 5.1
> - Windows NT 4.0 Desktop with serial cradle
> - ActiveSync 3.7
> - iPaq 5550 with German Windows CE 4.2
>
> After installing the ZfHProxy on the Desktop and connecting the PDA, a
> message appears on the PDA saying something like "ZfH Client
installation
> unsuccessfull". After disconnecting an reconnecting the PDA I get the
> message "ZfHClient already installed...".
>
> Is this environment supported or are there some known issues with this
PDA?
>
> Olaf Brandt
>

Tutorial - Connecting an Nokia Phone with an iPaq ...

This Tutorial is as a result of a post by qvodude on 13th January 2008.
Tutorial – Connecting an Nokia Mobile Phone to an HP iPaq Pocket PC
This tutorial has been done using a Nokia 6260 (S60 series 2) and an iPaq 5965 travel companion (windows mobile 5).
Turn on the phone and then go to menu>connections>Bluetooth. When you open Bluetooth you are asked to give your phone a name. (I named mine Nokia 6260). Hit ok. Then highlight Bluetooth and select options>change and switch Bluetooth on. Then scroll down to My phones visibility >options > change > shown to all >ok. Your phone is now set up.
Switch on the iPaq. Start > settings > iPaq Wireless and turn Bluetooth on. Then tap done. On the settings page tap on Bluetooth Manager. When you open Bluetooth Manager it gives you a welcome screen. Just follow the instructions. Luckily my phone is in the list so it was fairly simple. If your phone is not in the list then select Generic Dialer or generic generic. The ipaq will then search for devices in range. In my case it picked up my phone and my laptop. I then selected my phone and was asked if I wanted to pair the devices. I said yes accepted the code that was on the screen and then pressed next. A message then appeared on my phone asking if I wanted to pair with my iPaq. I entered the same code that was used on the iPaq and pressed ok. The ipaq then asked if I wanted to connect to the internet and I said no as I did not want to connect at this time.
On my phone if I highlight Bluetooth and scroll right it shows Paired devices > Pocket PC 5965.
I then tested the setup by tapping tools > connect on the iPaq. My phone then asked if I wanted to Accept connection request from pocket PC. I then selected yes and my Pocket PC showed that I was connected to my network (Optus).
I trust that this helps you. If you have any further problems let me know. I will be going away next Thursday 22nd and will not be back until Wednesday 28th. Whilst I am away I will not be in a position to access these forums so if you could get back to me before then I would appreciate it.
Regards
Barry

Hey Bazyeo, sorry im writing soooooo late. I just wonted to thank you for the post on "Connecting an Nokia Phone with an IPAQ..."
Been really busy with job changes and all, as you know the States (US) is going thru a really bad job $hit, and I got dump... well I **bleep** one of the upper management guys off and was asked to resign. But oh well thats another post
Adios mate!
Message Edited by qvodude on 16-Jul-2009 05:08 PM

How do I use Edge Web Fonts with Muse?

How do I use Edge Web Fonts with Muse - is it an update to load, a stand alone, how does it interface with Muse? I've updated to CC but have no info on this.

Hello,
Is there a reason why you want to use Edge Web Fonts with Adobe Muse?
Assuming you wish to improve typography of your web pages, you should know that Muse is fully integrated with Typekit. This allows you to access and apply over 500 web fonts from within Muse. Here's how you do it:
Select a text component within Muse, and click the Text drop-down.
Select Add Web Fonts option, to pop-open the Add Web Fonts dialog.
Browse and apply fonts per your design needs.
Muse also allows you to create paragraph styles that you can save and apply to chunks of text, a la InDesign. Watch this video for more information: http://tv.adobe.com/watch/muse-feature-tour/using-typekit-with-adobe-muse/
Also take a look at these help files to see if they help you:
http://helpx.adobe.com/muse/tutorials/typography-muse-part-1.html
http://helpx.adobe.com/muse/tutorials/typography-muse-part-2.html
http://helpx.adobe.com/muse/tutorials/typography-muse-part-3.html
Hope this helps!
Regards,
Suhas Yogin

How do I use an external mic with the iPad4?

How do I connect an external mic to the new iPad4? Older models seem to have worked, but the lightning connector causes a lot of problems. I would like to use my Zoom H1 with my iPad4 and GarageBand. Any ideas? Thanks so much!

Secrets of the iPad Camera Connection Kit
http://howto.cnet.com/8301-11310_39-57401068-285/secrets-of-the-ipad-camera-conn ection-kit/
 Cheers, Tom

How do I use Qt and OpenGL with Visual Studio

Hi! I mainly want to program in C++ and I want to use Qt and OpenGL with Visual Studio.
I am currently revising C++ and later on i am going to start reading Qt and OpenGL. I have a background of
Embedded firmware design(C and Assembly).
The Visual Studio Version I have is 2013 ultimate. How do I use Qt and OpenGL with Visual Studio?
Thanks
Alexandros

Hi ClassicalGuitar,
The forum supports VS setup and installation. And your issue is not about the forum. I will move the thread to off-topic forum. Thanks for your understanding.
Regards,
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click HERE to participate the survey.

How do i use my mac book with my HP 6510 e all in one series printer

how do i use my mac book with HP photosmart 6510 e all in one series

Hello Marilynatsea,
Thanks for using Apple Support Communities.
To learn more about printing in OS X on your Mac, and how to add a printer, take a look at the article linked to below.
Mac Basics: Printing in OS X - Apple Support
Cheers,
Alex H.

How do I use my gigaware webcam with my mac?

How do I use my gigaware webcam with my mac? I just bought this webcam on amazon http://www.amazon.com/gp/product/B00IJE0ISS/ref=oh_aui_detailpage_o07_s00?ie=UTF 8&psc=1 and I want to use it with my mac. Is there an adapter or any software to make it compatible? Thanks.

Your amazon link states, in part, that this webcam is:
Compatible with Microsoft Windows 7,Vista, XP, 2000
Use a Mac OS X Compatible Webcam like one of those shown in the linked article instead.
For best compatibility and security, also update your OS X Mavericks (10.9.2) to the current OS X version by restarting Mac and then downloading and installing OS X Mavericks 10.9.4 Update (Combo).

How do I use a foot pedal with my mac?

how do I use a foot pedal with my mac to use on YouTube?

Can you be more specific? What kind of foot pedal? What is the foot pedal used for?

How do i use a new computer with my ipod?

how do i use a new computer with my ipod?

See this apple support communities user tip…
Syncing to a "New" Computer or replacing a "crashed" Hard Drive

How do I use cell number associated with iPad 2 3G

How do I use cell number associated with iPad 2 3G

For Messages you can can use your email address, the iPad doesn't have a phone number that you can use.

How do i use 2 ipod touches with 1 itunes account?

how do i use 2 ipod touches with 1 itunes account? can they share apps and music etc. I'm not very good at any tech so advise would be much appreciated.

Yes. You can sync an unlimited number of iDvies that you control to one iTunes library/account. If using the same iTunes library on the same comutr just make sure that yu go to the ap. music and other pane for the iPod in iTunes and select sycn selected items. Not the the whole library. That way each iPod can have it own contents.

How do I use a regular printer with my iPhone?

How do I use a regular printer with my iPhone?

you can't unless it's an AirPrint enabled printer or you purchase a 3rd party app like printopia.

USE of CF 6004 with HP IPAQ 5550

Similar Messages

Maybe you are looking for