Use old HD with new P965 Platinum MB. Possible?

If I wanted to use my present HD with my new P965 Plat board, I have to boot with the OS CD and do a "repair" or a "install", or is this even possible?  Has anyone tried/done it?  Thanks.

Your "old HD" is P-ATA (IDE), right?
Theoretically it should not be a problem, if there is still room for a second drive on the JMicron IDE-port. 
However, you should install a fresh XP SP2 onto that drive using JMicron Drivers (F6).  Just "reparing" the existing installation might not work properly.

Similar Messages

  • How to use old TC with new TC for storage only?

    Bought a 2TB TC and I still have my older 1 TB. Is their any way to use the older time capsule as a hard drive only and have that TC backed up along with my iMac on the new TC?

    Basically the answer to this is NO!!
    You can set it up but not the way you are thinking.
    The TC is now and forevermore a network drive. You can therefore bridge the TC and plug it into your network. The obvious place being your new TC. You can also turn off the wireless in the old TC.. it is now a network accessible hard disk.
    But Time Machine has a huge limitation.. it cannot backup network drives. So your TC cannot be backed up with your  iMac to the new TC. Not by Time Machine. You can buy a different backup software.. eg CCC is excellent and use that.
    Overall the TC is slower and less reliable than a USB drive plugged straight into your iMac.. especially if the iMac is newer type with USB3 ports.
    And the USB drive is local and so it can be backed up by Time Machine. (Must have HFS+ format and be included in the backup).

  • How to use old library with new computer?

    Hello,
    I keep all my music on an external HD. Recently, my main computer died, so I had to start using another iMac. It's running Tiger and iTunes 6, but I have never used the iTunes before. How do I get this computer to "see" my old iTunes library (on the external)?

    You are welcome. One thing that comes to mind is that I believe when you use an external drive to hold your library, it is important that the external is on and mounted when ever you start up iTunes. My understanding is if you start iTunes and the external drive is not available, then iTunes reverts back to the default location on your internal. You then have to reset it back to the external, but I think you also have to re-add everything all over again.
    So be sure you always have the external up and ready whenever you open iTunes.
    Patrick

  • How to intigrate old APPL_TOP with new Product. R12

    hi All,
    I am upgrading APPS 11.5.10 to R12.
    I am sucessfully upgrade Apps file system and database.
    And R12 services and Database service are running sucessfully.
    But Problem is that i want to use OLD Business Flow means I want all old form and report behiver.
    Means how to intigrate old APPL_TOP with new Product. R12.
    thanks
    c2

    Hi,
    For custom forms and reports, you need to open it using Forms/Reports Builder 10g, compile it, and upload it again to the server.
    For the CUSTOM_TOPs, make sure it is set in the custom<CONTEXT_NAME>.sh file under $APPL_TOP, and in default.env file on the Applications tier.
    Note: 563258.1 - How To Upgrade 11i Custom Forms And Reports To R12
    https://metalink2.oracle.com/metalink/plsql/ml2_documents.showDocument?p_database_id=NOT&p_id=563258.1
    Note: 552010.1 - Can't Open Custom Forms After R12 Upgrade
    https://metalink2.oracle.com/metalink/plsql/ml2_documents.showDocument?p_database_id=NOT&p_id=552010.1
    Note: 451934.1 - Accessing Custom Forms After Upgrading From To R12
    https://metalink2.oracle.com/metalink/plsql/ml2_documents.showDocument?p_database_id=NOT&p_id=451934.1
    Regards,
    Hussein

  • How to use facebook  + skype with new Ipad? it needs flash player it seems...

    how to use facebook + skype with new Ipad? it needs flash player it seems...

    get the facebook and skype apps from the app store and there is no need flash.

  • How to use track effects with new version of GarageBand

    In the version of GarageBand before this one, you could access different effects that you could manage and apply to the different tracks.  Each track had an area containing its set of effects that were either activated or deactivated.  With this removed, i am not sure how to add those same kind of effects.  I am aware of the new nobs that are provided in order to mix and edit trebles, bass, mid, etc., but i want to be able to add different effects such as voice transformer, flanger, chorus, speech enhancer, bit crusher, bass amp, track echo, track reverb, amplifier, etc.  I desperately need help finding out how to do this, as this was a major part of my mixing and producing with GarageBand, and without these given effects, i do not feel as comfortable using GarageBand.

    zachseiden wrote:
    How to use track effects with new version of GarageBand
    this may help:
    http://www.bulletsandbones.com/GB/GBFAQ.html#replacemissingtrackeffectsgbv10
    This FAQ entry offers a Minute GarageBand video tutorial
    (Let the page FULLY load. The link to your answer is at the top of your screen)

  • Replacing old TC with new larger capacity TC and using old TC as an external HDD

    I currently have a 500GB 1st gen TC.  I am running out of space for back ups and running out of room on my iMAC HDD.  I would like to purchase a nw 2TB TC to back up both my iMAC, macbook, and expected Macair when the new ones are released.
    Questions:
    1. Can I use the old TC as an external HDD only?  I would like to place my iTunes Library and photos on it so it is visilble accross the network via wi-fi.
    3.  If I move my libraries is there a method to make them available to me when I travel via the internet?  Or is this the upcoming cloud sharing I've heard so much about? 
    2. My understanding from vaious discussions is that I can not connect the old TC (via the TC USB port) directly to the the new TC and have the old one continuously backed up to the new one (iMAC---new TC usb---old TC).  In other words, if I were to move my itunes and photo media to the 500GB old TC then they would not be backed up.  However, what if I conencted the old TC directly to the iMAC? 
    old TC----iMAC---new TC
    Would it back-up to the new TC now?  Can I connect it to the iMAC ethernet port or would i have to use the USB connection?
    3.  Can I daisy chain them together in a way that the new TC will backup both the iMAC and the old TC?
    iMAC---old TC----new TC

    golf and fly wrote:
    I currently have a 500GB 1st gen TC.  I am running out of space for back ups and running out of room on my iMAC HDD.  I would like to purchase a nw 2TB TC to back up both my iMAC, macbook, and expected Macair when the new ones are released.
    You can connect a USB drive to the TC, and back up some or all of your Macs to it instead of the TC's internal HD.  See #Q2 in Using Time Machine with a Time Capsule.
    And you can put other data there, too, such as your iTunes library, but for best results you'll want to partition the disk. Otherwise, Time Machine will, eventually, use up all the empty space.
    Also note that Time Machine cannot back up from any network drive, so you'll need to find an alternative way to back up that "other" data.  The Chronosync app might be viable.

  • Using an old mac with new ipod?

    I own a beige PowerPC G3 (333 Mhz) with USB PCI card and Mac OS 10.2.8. I was wondering if it's possible to use the 5th generation ipod on my aging machine? I plan on purchasing something new very soon, but I was hoping I could at least use my new ipod on my old machine for a little while. I am using itunes 6.0.1.
    Thanks.

    Thanks for the response. I was hoping to find someone that has been successful with using their ipod with an older machine despite the fact that apple states a user needs more up to date hardware than what I already have. Has anyone out there had any success?

  • Using dbms_xmlgen.getxml with new and old tables in triggers

    Is there a way to use getxml against the data stored in the new and old tables in a trigger? Simply doing this:
    Xml_Variable := dbms_xmlgen.getxml('Select * from New');
    Does not work.
    Edited by: user13302591 on Jun 16, 2010 1:16 PM

    user13302591 wrote:
    How would I pass the information from the :new and :old to getxml?What are you trying to do? You could use, for example:
    XMLELEMENT("old",:old.column_name)
    XMLELEMENT("new",:new.column_name)SY.

  • New Computer with the P965 Platinum

    Hello. I'm new to computer building. I'm tired of Dell. I just ordered the following setup:
    1 Thermaltake Bach VX Mid Tower Computer Case
    1 Thermaltake Purepower 600W Power Supply
    1 MSI P965 Platinum Motherboard
    1 Intel Core 2 Duo E6700
    1 ZALMAN 9700 CPU Cooler
    1 Mushkin eXtreme Performance 2GB (2 x 1GB) DDR2 SDRAM DDR2 800
    1 EVGA GeForce 8800GTX
    2 SAMSUNG 500GB 7200 RPM SATA 3.0Gb/s Hard Drive
    1 SAMSUNG 18X DVD±R SATA DVD Burner
    1 ASUS Black SATA DVD-ROM Drive
    1 Microsoft Windows Vista 32-Bit Ultimate
    Did I screw anything up? I was wondering if I will be able to assemble the computer and have it boot the first time. Or should I expect problems? Does anyone have any insight or wisdom for me as to what I should expect?
    I had a few specific questions:
    1.) RAID0 configuration: Is there more than one RAID controller? If so, which is better?
    2.) Windows Vista (32 bit) installation: Is there anything I should do before installing Vista?
    3.) Overclocking: After the dust settles I want to mildly overclock my CPU, GPU, and RAM. Does anyone have any recommended overclock settings or links on how to do this?
    Thank you.

    Why overclock? Mainly because of intellectual curiosity and because faster is better all else equal. It's like Spinal Tap - I want my volume to go to 11!
    Thanks T_smith for the overclocking how-to, but it appears my BIOS options on the P965 are different that yours. I will start a thread in the Overclocking forum.
    My computer runs great and is fast. It's been quite a learning experience so far. You guys have been a lot of help. Thank you.
    I created a bootable USB drive (definitely good to have around) and flashed the BIOS to 1.5b3.
    At boot time, the computer beeps once for every USB device that is plugged into the computer. Is there a way to disable that beep in the BIOS? I have a USB mouse and keyboard and it's a bit annoying to listen to the beeps.
    I installed CPU-Z. I got a scare to see my CPU idling at 1.6 GHz instead of 2.67 GHz (6 multiplier vs. 10 multiplier). Then I realized it was completely normal because of Intel SpeedStep.
    I installed MSI DualCore Monitor, nVidia nTune, CoreTemp to monitor my temps.
    Here are my temps:
    Closed case (messy wires still)
    - GPU 68 C
    - System 40 C
    - CPU 34 C (CoreTemp & DualCore Monitor) vs. CPU 40 C (H/W in BIOS)
    Does anyone know why the CPU temp measurements differ so dramatically? SpeedStep?
    If I take the side panel off the computer, all temps drop 3-5 C.
    I noticed that HDD write cache is disable by default. Do you guys think it's worth enabling? It's a performance vs. data protection question. I don't mind a little data loss in the event of a power failure, but I don't want the OS to become permanently unstable.

  • Windows XP-Pro will not install on my new P965 Platinum

    I hope someone can help me with my problem.
    It seems that everytime i try to install Windows XP-Pro after the initial
    drivers setup i get this Error Message:
    A problem has been detected and windows has been shut down to prevent
    damage to your computer.
    If this is the first time you've seen this stop error screen, restart
    your computer. If this screen appears again, Follow these steps:
    Check to be sure you have adequate disk space. If a driver is identified
    in the stop message, disable the driver or check with the manufacturer
    for driver updates. Try changing video adapters.
    Check with your hardware vendor for any BIOS updates. Disable BIOS
    Memory option such as caching or shadowing. If you need to use Safe Mode
    to remove or disable components, restart your computer and press F8 to
    select Advance Start up options, and then select Safe Mode.
    Technical Information:
    *** STOP: 0x0000007E (0xc0000005, 0xF78350BF,0xF7C81208,0xF7C80F08)
    *** PCI. sys-address F8350BF base at F782E000, Datestamp 3b7d855c
    This is a new build with a Samsung Spinpoint SP2504C SATAII Drive but
    when this occurred i thought that it might be the drive that was the
    problem.So i therefore put it i my Old PC and tried to install Windows
    XP-Pro onto it which i did with no problems at all.
    I then put the drive back in my New PC where it Booted Up First Time and
    runs OK and i have even installed Software onto it.In fact i am using at
    this very minute as i type.
    Unfortunately when i still try to Reinstall Windows XP-Pro on my New Build
    with my P965 i get the same Error Message as above.
     Can anybody please help.
                                       Thanks
    P965 Platinum
    Intel Core 2 Duo E6300
    Samsung Spinpoint SP2504C SATAII
    Corsair 1GB DDR2 Twin2X(5x512MB)
    inno3D GeForce 7600GT
    Creative Sound Blaster X-Fi Extreme Music Sound Card
    NEC ND-3520 DVD
    Arctic Cooling Freezer 7 Pro
    Thermaltake Toughpower 600W
    Thermaltake Tsunami Dream Case

    Quote
    I hope you don't mind me asking this question for Jack the Newbie.
    You say i have to use a Windows XP-Pro Install-CD that includes SP2 as well as the JMicron driver for the JMicron IDE-Port which i have my Optical Drive connected to.I know this is telling me how to fix my problem, but what i would also like to know is WHY do i have to install it with SP2 & the JMicron driver like this on my P965 when it installed on my old pc with just the XP-Pro Install-CD.
    Your Windows Installation CD should be as up to date as possible, especially for newer hardware.  SP1 is from 2002, SP2 was released in 2004. Neither SP1 nor SP2 install CDs provide the proper drivers for the JMicron chipset used on your mainboard.  I cannot give a detailed list about the differences between SP1 and SP2. I just know, that there are a lot of problems when people do not use SP2 on Intel 975/965 Chipset-boards which where released in 2006. 
    When you say that your installation works fine on your old PC I believe you.  It worked on my old Laptop too.  However I was not able to install XP Pro on my 975X-board without SP2 at all until I upgraded my Installation CD.
    Quote
    Garfield,
    I had exactly the same problem--because I had my optical drive hooked up to a Promise IDE controller, rather than to a mobo IDE connection.  Turns out the Promise will read and write the optical drives OK, just won't boot from them properly.  And, somehow, that affects Windows Setup.
    I don't know anything about the JMicron and the need for SP2.  But, as you can see from my sig, I'm using XP Pro SP1, and once I moved my NEC 3500 back to the mobo IDE (as secondary behind my IDE hard disk) everything worked like a champ.
    Just my $.02.
    Stahlwird
    To relate Garfields problem with your solution is a mistake.  Your board does not use any JMicron hardware, has NVidia chipset instead of Intel and an AMD CPU.  Your are talking about a totally different Setup here.

  • Can't replace old text with new text in a text box

    Hello everyone. This is my first time posting in the forum, so I'm hoping this works out well. We recently purchased a few copies of Adobe Acrobt X for the office, and one of the users is having an issue with editing text in a field. She can type new text into a box, but when she goes back to replace that text with something else, the old text stays. New text appears on top of the old text, and you can see both. Is there a way to simply highlight the old text, delete it, and then replace it with new text? Thanks in advanace for your assistance. I understand this might be confusing, so let me know if you have questions.
    Thanks,
    Dan

    You have to use the text touchup tool (there is a new name like text edit tool in AA X) to edit such text. It sounds like you are using the typewriter tool or something like it. Text editing in Acrobat is not for the weak at heart. It can be very frustrating and is not recommended except for very minor changes. If at all possible, you should edit the original and just recreate the PDF.

  • Using older servos with new controller

    My group has a three-axis stage controlled by an old Galil DMC-230
    motion control board, Galil ESA-10-75 amplifilers and three dc servo
    motors (from Galil too, I think).  The board is mounted in an
    ancient computer running DOS.  To make matters worse, the hard
    drive seems about to give out.  We would like to leave the stage
    and motors alone but replace the controller and amplifiers.  We
    are considering using an NI PCI-7344 controller with an NI MID-7604
    Motor Drive.
    My questions are:
    What are the main things to consider when matching a servo motor to a controller?
    Has anyone done anything similar (using older servos, but replacing controller and drive)?
    Should I just give up and beg the boss to buy new motors as well?
    Thanks for any advice!
    Telemaque

    Been there and almost done that. We have a legacy DOS Galil based (DMC-630 controllers with SSA-12/40 drives) system with brushed servos that is on it's last legs.
    Matching servo to drive amps- look at max currents, voltages, and inductances on the motors to see if drive can accomodate. Are they brushed or brushless motors. Also check if encoders and hall signals from existing motors and limits from stages compatible with new controller.
    Personally, I would suggest new motors since you may not know their history of (ab)use and depending on their ratings, may be a minor percentage of total retrofit cost. You may also want to have the stages sent out for refurbishment if time permits. They have probably seen a lot of use with little or no cleaning and lubrication. Mechanical wear also takes it's toll. On the system I mentioned above, we were experiencing loss of accuracy and repeatability- the lead screws and nuts were trashed.
    Just a couple ideas to start with.
    Good Luck
    AK2DM
    ~~~~~~~~~~~~~~~~~~~~~~~~~~
    "It’s the questions that drive us.”
    ~~~~~~~~~~~~~~~~~~~~~~~~~~

  • Migration of old system with new version and 64bit hardware

    HI Sapguru's,
    Our req: Build New CRM system with all latest version of software & 64 bit hardware. Details mentioned below.
    Old System:
    CRM 4.0 ABAP System
    win 2003
    Oracle 9i
    non-unicode
    32 bit hardware
    New System( which i want to build):
    CRM 5.2 (rampup version) ABAP+JAVA
    win 2003
    Oracle 10g
    Unicode
    64 bit hardware
    Above mentioned is an new requirement for us.
    Our Plan:
    1. Old system -Conversion from non-unicode to Unicode system
    2. Old system - System copy export method for create exports
    3. Build New system with new unicode version(5.2) with Old system exports
    Questions to Sapguru's:
    1. Our plan will work or not?
    a. If Yes - give me the guidelines ,Notes ,documentation paths
    b. If No - Please provide your opinions/advices
    2. 32 bit exports will work on 64 bit hardware SAP system?
    Thanks Advance.
    Regards,
    Ramu,

    Hello Markus,
    Thanks for your quick response!!!!
    I understood - what you have mentioned for my question but i have  one clarification on your answer and one new questions to you.
    Clarification:
    My oldsystem is non-unicode system. As you said i will do system copy export method on old system(non-unicode) then i will use that  exports(non-unicode) to build new system.
    Here my clarification is:
    Will that exports(non-unicode) work while installing new system with unicode? or Will it give any problem?
    Question:
    1. will old system with oracle 9i exports work on new system with oracle 10g?
    Thanks Advance,
    Bhaskar Rapelli

  • Old Archive with New Blog?

    I am changing my blog template from the Travel theme to the Gazette theme. I've been using the travel one for months now. What do I do with my archive? Is there a way to move the Travel Blog Archive to the new blog? I like the Gazette Blog main page better as well as each blog entry page. As far as I've been able to figure out, I am unable to just change the theme of my travel blog page to the gazette, I have to start a new page. Is anyone able to offer any advice?

    Hi Esther...
    As you have concluded, there is no way to transfer your blog entries from one theme to another. Your only option is to start a new blog page. Of course, you can still leave your current blog online...maybe just put a final entry with a link to the new blog page. Then have both links available in the navigation menu....like old blog and new blog. Sorry I don't have better news for you.

Maybe you are looking for