Use WRTP54G-ER wireless router with other ISP?

I got a Linksys WRTP54G-ER router with 2 phone ports from Circuitcity. We have Cable phone, and internet services with Times Warner.
On the package of the router it shows "Wireless-G broadband Router with 2 phone ports, Configured specifically for Earthlink trueVoice services"
Will this router works with the system we now have?

Yes it will work fine with the Cable Connection ...if you want to use Phone service you need to contact the Earthlink .... voice service provider ...

Similar Messages

WRTP54G (wireless router with phone hookup) with Panasonic network camera BL-C30A (WEP only)

hi
I would like to use this wireless router with WEP so I can access the camera wirelessly (camera only does WEP encryption).
The camera should be the only device allowed to connect to this router wirelessly.
I can dedicate channel 11 so only this wireless router uses it
I know WEP can be cracked but I'm thinking maybe I can setup the router so it doesn't matter, i.e.,
so only the camera can be accessed through this particular router
so my questions are:
1. can I setup the router so only outgoing local LAN http requests are allowed?
2. any other suggestions on router setup that will prevent access to my network?
(using MAC address filtering (for camera mac address only) is worth doing but I guess MAC address can be spoofed so not a complete solution)
thanks,
Tom
Solved!
Go to Solution.

I think "toomanydonuts" has provided my solution in this thread:
solution thread
thanks,
Tom
Message Edited by coffee_addict on 01-03-2010 02:27 PM

Configure WRT54G Wireless Router with PUBLIC IP address and use DHCP for internal computers

Hi,I have an Internet online service with 5 public IP addresses. The router and the AP are connected to a switch. I would like to configure a WRT54G wireless router with one of this IP public Address and use DHCP (with private ip address) for the computers that will connect to the AP. As the AP is connected to the switch it is possible that other wired computers that are connected to the same switch can obtain an IP address from the DHCP ?
Thansk in advance

Thanks for your help. Please correct me if Im wrong. After connecte the equipments the way you suggestI setup a static IP address (The public IP) in the WRT54GI enable DHCP in the WRT54G with a range from 10.10.0.100 to 10.10.0.200 (as an example) The gateway is the Public IP address right ? How do I route the 10.10.0.x addresses to the public IP address. Thansk again

Using AX as wireless router, how to set up w/ security and airtunes on XP

I previously had a Linksys wireless router. I just purchased an Airport express to use as the wireless router (and remove the Linksys router) as well as use the Airtunes functionality.
After some trial and error, I have been able to wireless connect my computer to the AX on it's own (the linksys router is now unplugged and out of the equation). I can connect to the internet fine on my PC (XP Pro SP2).
Trouble is, when I use the Network Setup Assistant, it shows the apple network listed, but it can't connect to it, no matter how many times I try, reboot my machine or reboot the AX. I've tried both the "setting up a new network" and "editing an existing network" option, and in each selection, after a few minutes of trying to connect to the network, I just get a failure message.
If I try and use the Admin utility, nothing shows up in the left-hand list window, and when I Press re-scan, still nothing shows (it doesn't even appear to scan).
I'm not sure what I'm doing wrong. I can't find simple instructions on how to set up the AX as the only wireless router for a PC and set up security and Airtunes (I'm assuming enabling airtunes is done in these applications, as I haven't seen anything about that yet either).
Any ideas on how this is done with a PC? Much thanks!
Dell 4500 series

I have found the 'DHCP Reservations' option on the AirPort Extreme to be buggy. I seem to remember it causing IP conflicts for some reason. I think what I remember is that if the computer with the reservation was off, and the DHCP server then handed out that IP to another DHCP client, then there would be a conflict when the reserved IP computer was turned back on. Maybe it was an issue in ealier versions of the AE or OS X as the case may be, and maybe it's been corrected, but I've never bothered using it agian since the method I describe below has always worked without fail. Also, I'm guessing DHCP Reservations would work fine if one manually enters IPs outside of the DHCP range but in the AE 'DHCP Reservation Setup Assistant' the IP options provided are within the DHCP range which to me makes no sense and increases the potential for IP conflicts.
Here's what I do to setup a mixed environment of static and dynamic IPs on my network. It works like a charm and does not require the DHCP server (beyond the distribution of dynamic IPs to hosts using DHCP).
For machines on my network that are accepting services from the public network, I set them up with static IPs using the 'Manually' option (System Preferences/Network/Ethernet/Configure IPv4). The settings for 'Router' IP address and 'DNS Server' IP address should both be set with your gateway/router LAN IP). Use an IP address below or above the DHCP range of adresses (in AE/Internet/DHCP/DHCP Beginning & Ending Address).
i.e. if my subnet is 10.0.1.1 and my DHCP range is 10.0.1.100 to 10.0.1.150, you could set the static IPs on your local hosts as 10.0.1.x where x = any number from 2 - 99 or from 151 - 200 as an example.
All other machines and devices that do not require static routing are setup as DHCP clients and get a dynamic IP from the AE. To me it's a simpler setup though it might take a little extra time to setup initially.
John

HT4628 I can not use the internal wireless card with my Mac pro 2012, I don't know if it is broken

I can not use the internal wireless card with my Mac pro 2012, I don't know if it is broken. The problem is happen recently, I have to use an independent wireless card now. Thanks!

When you enable Internet Sharing in OS X, you are creating a separate sub-net.
There is no option to allow this to be a simple pass-through from Ethernet to AirPort (or the other way).
The problem is easily solved by getting an inexpensive wireless router. You can replace your current router OR disable the DHCP server on the wireless router and allow the wireless clients to get an IP address from the current router.

Need a new wireless router with switching

I would like to purchase a new wireless router with 4 port switch. I have an Intel iMac with 2 pc's and have spent hours trying to configure my existing Linksys router to work properly and need to make a change. I have not been able to use iChat with Powerbook users and have had other problems as well and have given up...
The recommended router list on the iChat website does not specifically mention wireless routers with 4 port switching...
Does anyone have any suggestions for a router which is easy to use and configure?
Thanks,
cj

Hi Herpestes,
If you mean which method of opening the ports should you use for those computers it will be the UPnP setting found in the Adminstarion tab
Log on to the Linksys by typing 192.168.1.1 into a web browser
Type admin as User ID and Password.
Go to Administration
Enable UPnP
10:10 PM Wednesday; June 28, 2006

I am trying to connect a Windows 7 / 64 bit to an Epson printer on my Mac. The printer is hooked into the Mac via USB; the Mac is networked to a Linksys wireless router with an ethernet cable, as is the Windows box. Any tips on how to do this?

I am trying to connect a Windows 7 / 64 bit to an Epson printer on my Mac. The printer is hooked into the Mac via USB; the Mac is networked to a Linksys wireless router with an ethernet cable, as is the Windows box. I installed the current Bonjour printer services software on the Windows machine, and separately installed the driver software for the Epson printer on the WIndows machine. Running the bonjour wizard, I get an alert saying 'I don't have sufficient access to my computer to connect to the selected printer'.
The printer has 'sharing' turned on from the Mac end; this works with a Powerbook via the wireless connection. Sharing is also turned on in the Windows printer control panel for this printer (under properties). The Mac is a G5 running 10.5.8. When I try to print a page from the Windows machine it gets hung in the print queue.
Any advice how to proceed would be appreciated!
thx,

I am trying to connect a Windows 7 / 64 bit to an Epson printer on my Mac. The printer is hooked into the Mac via USB; the Mac is networked to a Linksys wireless router with an ethernet cable, as is the Windows box. I installed the current Bonjour printer services software on the Windows machine, and separately installed the driver software for the Epson printer on the WIndows machine. Running the bonjour wizard, I get an alert saying 'I don't have sufficient access to my computer to connect to the selected printer'.
The printer has 'sharing' turned on from the Mac end; this works with a Powerbook via the wireless connection. Sharing is also turned on in the Windows printer control panel for this printer (under properties). The Mac is a G5 running 10.5.8. When I try to print a page from the Windows machine it gets hung in the print queue.
Any advice how to proceed would be appreciated!
thx,

HI I HAVE WRT54G WIRELESS ROUTER WITH VERSION 7. NOW I W...

HI
I HAVE WRT54G WIRELESS ROUTER WITH VERSION 7.
NOW I WANTED TO UPGRADE THE FIRMWARE.
I CHCAKED OUT THE SITE I COULD'NT FIND THE DRIVERS FOR THE VER 7
EVERYTHING ELSE OTHER THAN VER 7 IS PRESENT ON SITE I WANTED TO CHEAK OUT WHEATHER THE VER 7 FIRMWARE ARE AVALIABLE OR NOT PLEASE HELP ME TO DO SO
THANKS
PRAVIN

hi helm
Thanks a lot for your suggestion i got the required farmware
thanks
prav

Can I use the Ethernet Port for a computer when it is also used as a wireless network with an Airport Extreme as the access point for the wireless network

Can I use the Ethernet Port of the A1264 Airport Express to connect to the Ethernet port of a computer that does not have wireless capability when the Airport Express is also used on a wireless network with an Airport Extreme 5th generation as the access point for the network?
I have AE 5th gen
looking to buy (from ebay) the AEX A1264
Various computers, printers and hubs for the network
Is this possible to do?

Bob, Thanks for the info. I have read different articles that said yes, but I wanted to make sure before I commit to buy. I have an older A1084 which I could not use the Ethernet port. I know at one point I was able to when I was on 10.4. Now that I am on an Intel processor and 10.8 I am going to have to upgrade some of my Apple wireless hardware.
Thanks Again.

Using iphone 5 and 5c on ios7.0.4 and would like to use these on wireless only with no carrier service for voip apps. how to i prevent the Iphone is not activated contact your carrier?

Hi i am using iphone 5 and 5c on ios7.0.4 and would like to use these on wireless only with no carrier service for voip apps. how to i prevent the error Iphone is not activated contact your carrier?

tnguyen9 wrote:
when i remove the sim card it gives me errors that there is no sim.
You should only need a SIM in it to actually activate it in iTunes. Once activated, leave the SIM in or remove it, it should not matter.
Then, turn on airplane mode. And then, go into wifi settings and re-enable wifi (this leaves the cellular radio in airplane mode = powered off).
Now your iPhone is effectively no more than a (wifi only) iPod Touch.

I have been trying to use an apple wireless keyboard with my ipad 2. I will be typing then suddenly the ipad will repeat the key strock about twenty times. It drives me crazy. What is happening and why?

I have been trying to use an apple wireless keyboard with my ipad 2. I will be typing along and suddenly the ipad will take off and repeat the key stroke about twenty times rapid fire. It really makes me crazy. What is happening and why? Help

Found this thread by searching the forum. I hope it helps.
https://discussions.apple.com/thread/5471311

Bt home hub 4 with other isp

hi all i have been advised by my isp (sky) to ask here if anyone can help me i am wanting to use my bt home hub 4 the one that can be used with other isp's.
i have tried several times to get this to work with sky i have even used info got from here
https://www.cm9.net/skypass/index.cgi
but to no evale and im desprately wanting to use my home hub 4 as the sky hubs are rubbbish if anyone can help me with this it would be very much appricated thanks in advance and look forward to hearing from you

Try the Sky user forum.
http://www.skyuser.co.uk/forum/
The BT Broadband supplied HH4s are locked to BT only, as the user name and password are hard coded.
Its possible that you have been sold the wrong one.
There are some useful help pages here, for BT Broadband customers only, on my personal website.
BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones.

TS2570 doesn't work, still the same problem when using Rapidweaver software. NOT with other software.

i tried everything in this article, but still have the same problem when using Rapidweaver software. NOT with other software. I am converting my iWeb site to Rapidweaver, whenever there is a calmer period in my office. I have 16 Gb RAM on my NEW iMac and have Parallels desktop, mail, safari, iWeb and Rapidweaver running simultanious.
I never have the problem if i don't use Rapidweaver, but after i have added several pages to Rapidweaver, the problem begins. my iMac won't start up. the only thing that works is re-installing Macos OS X 10.8. i tried even whiping the completeharddrive, and reinstalling with a complete new user, the same problem.
I had it on my previous iMac also, and bought a new one because i thought the problem was in the iMac first. i hadn't noticed it only happens with using rapidweaver.
i sent my complete rapidweaver project to the programmers from rapidweaver at Realmacsoftware, but they couldnt reproduce my problem, there macs started up without any problem.
i deleted all the rapidweaver addons and extra stacks, and started a complete new project.
saterday i had the problem again, after adding about 5 new pages to my rapidweaver site.
i think i have reinstalled Macos OS X 10.8.2 20 or 30 times by now
does anyone have a sollution?

Type '''about:support''' in the URL bar and hit Enter.
Scroll down almost to the bottom of that listing and see if you have '''user.js Preferences''' just above the '''''Graphics''''' category.
If you do have that, click on '''user.js file''' in this sentence. <br />
''Your profile folder contains a user.js file, which includes preferences that were not created by Firefox.''
Does that "different homepage" appear in that user.js file?

Can I use a iPhone 4S unlocked with other company?

Can I use a iPhone 4S unlocked with other company? I would like to buy a iPhone 4S unlocked to use it with Simple Mobile Company. I called them and they told me yes I can do it, but I want to make sure before spend the money.
Thank you

Thank you so much

Can I use built-in iSight camera with other apps?

Can I use built-in iSight camera with other apps?
How?
doesn't work in imovie or image capture

Hi Judson,
THe built in iSight will actually work with iMovie if you have the version of iMovie which comes with iLife 6. (see http://docs.info.apple.com/article.html?artnum=61929 for a mention)
There is a slightly clumsy "workaround" available for use with earlier versions of iMovie, but you need a dv cam to use it - see http://www.macosxhints.com/article.php?story=20051217210335199
I gather that "EvoCam" - http://www.evological.com/evocam.html - will also work directly with the built in iSight.
So too, should recent versions of QuicktimePro.
As for other apps, tell us what you wish to do with it. We may be able to come up with some suggestions.
Cheers
Rod

Use WRTP54G-ER wireless router with other ISP?

Similar Messages

Maybe you are looking for