User Contributed Tips, MacBook Pro (Original) Power and Batteries, MB Pro

*The following User Contributed Tips are located in the MacBook Pro (Original) > Power and Batteries on a MacBook Pro forum:*
None at this time.
*The following related tips are located in other areas of Apple Discussions:*
neuroanatomist - Apple notebook batteries – maintenance and troubleshooting
http://discussions.apple.com/thread.jspa?threadID=1764220
Publish date: Oct 23, 2008
See Also User Tips Library

Frani wrote:
Hi Martin, thanks for your response, I'll have a good read through that article. Just to fire some more facts at you:
My superdrive has been playing up intermittently for a while. Sometime it wont read the content on CDs / DVDs - usually copied / PC & Mac written discs, not commercial ones. However I haven't been trying to read and discs when the problems have happened.
I upgraded my hard drive from a 320Gb to a 500Gb disc about 6 months ago and the switch was done by a competent Apple Authorized Service Provider. For a few weeks after the new drive had been installed there were a few occasions where the disc was making some noise, like a clicking noise. This would start and go on for a minute or so then seem to dye down and stop. It happened a total of about 10-15 times but when I reported this to the person that fitted my new hard drive he assured me he felt it was unlikely to cause a problem. he did say that if it went on to be an issue they would replace the drive of course. Like I said this was all done about 6 months ago and the clicking noises only happened a handful of times in the first month or so after the install and it did have one bad crash in this time but since then it has been fine.
I just wondered if you thought either of the above might be a cause of the issue?
Thanks
Frani,
I think the optical drive is not your problem, but it sounds like it needs replacement. There's a 75% chance it's your hard drive. Read the article on kernel panics. It takes time to diagnose the issue, but if you get TechTools and run a full diagnostic, you might find out if it's a hardware issue. But fix permissions and clean out your cache first, just in case it's a simple fix.

Similar Messages

  • User Contributed Tips, MacBook (Original) Power and Batteries on a MacBook

    *The following User Contributed Tips are located in the MacBook (Original) > Power and Batteries on a MacBook forum:*
    <pending>
    *The following related tips are located in other areas of Apple Discussions:*
    neuroanatomist - Apple notebook batteries – maintenance and troubleshooting
    http://discussions.apple.com/thread.jspa?threadID=1764220
    Publish date: Oct 23, 2008
    See Also User Tips Library

    Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.
    Back up all data on the internal drive(s) before you hand over your computer to anyone. There are ways to back up a computer that isn't fully functional—ask if you need guidance.
    If privacy is a concern, erase the data partition(s) with the option to write zeros* (do this only if you have at least two complete, independent backups, and you know how to restore to an empty drive from any of them.) Don’t erase the recovery partition, if present.
    Keeping your confidential data secure during hardware repair
    Apple also recommends that you deauthorize a device in the iTunes Store before having it serviced.
    *An SSD doesn't need to be zeroed.

  • User Contributed Tips, MacBook Air Battery and Power on MacBook Air forum

    *The following User Contributed Tips are located in the MacBook Air > Battery and Power on a MacBook Air forum:*
    None at this time.
    *The following related tips are located in other areas of Apple Discussions:*
    neuroanatomist - Apple notebook batteries – maintenance and troubleshooting
    http://discussions.apple.com/thread.jspa?threadID=1764220
    Publish date: Oct 23, 2008
    Also see User Tips Library

    Power or other problems related to unexpected system sleep, shutdown, lights or fans call for an SMC reset:
    Resetting the SMC on portables with a battery you should not remove on your own
    Shut down the computer.
    Plug in the MagSafe power adapter to a power source, connecting it to the Mac if its not already connected.
    On the built-in keyboard, press the (left side) Shift-Control-Option keys and the power button at the same time.
    Release all the keys and the power button at the same time.
    Press the power button to turn on the computer.

  • User Contributed Tips, MacBook (black and white) Using your MacBook Forum

    *The following User Contributed Tips are located in the MacBook (black and white) > Using your MacBook Forum:*
    a brody - I need Firewire for Camcorders, yet the MacBook and MacBook Air lack it
    http://discussions.apple.com/thread.jspa?threadID=1928027
    Publish date: April 4, 2009
    *The following related tips are located in other areas of Apple Discussions:*
    Please see the User Tips Library

    Keep the temperature down, usually by boosting the lowest default fan speed to help.
    Also FBDIMMs on Amazon I have run at 59*C versus the 72*C+ of prior modules so adding less heat into the system.
    There are kits you can modify the card's fan and add copper heat sink pipes. You may be fine and not have to buy a new card and continue with the 8800GT.
    The X1900 was a huge problem with dust and therefore with heat and making the fans work harder - but never able to cool the interior, so the card had to be removed and dust inside the card's chamber 3-4X per year.
    My Mac Pro 1,1 even without the X1900 would warm up the area during winter after 3-4 hours of use - the exhaust on these is very hot. So monitor the temps and fans and I would  install SmcFanControl - I have always had it since 2007 to keep the fans default at 800-900 rpm along with Hardware Monitor (or use another) to monitor all the system sensors.

  • User Contributed Tips in Final Cut Express and Final Cut Express HD Forum

    *The following User Contributed Tips are located in the Pro Applications: Video > Final Cut Express and Final Cut Express HD Forum:*
    skalicki` - Working with AVCHD: Log and Transfer FAQs
    http://discussions.apple.com/thread.jspa?threadID=2672530
    Publish date: December 03, 2010
    skalicki` - Final Cut Express: Basic Troubleshooting
    http://discussions.apple.com/thread.jspa?threadID=2662419
    Publish date: November 26, 2010
    *The following related tips are located in other areas of Apple Discussions:*
    Please see the User Tips Library

    I'm relatively new to FCE myself, so I'll answer with what I know. I'm sure the more experienced folks will either add to or correct what I say.
    1) For the Inconvenient Truth thing, I believe this would best be done in LiveType, which does allow you to do animations, and to work on individual letters and characters. Whether or not it could exactly reproduce the effects in the clip, I'm not certain, but I'm sure it could come very close.
    2) For the Crowd or the Cross effects, there are two things going on at once: effects on the text, and effects on the video. My gut feeling is that both FCE and LiveType can do these, with lots of work and patience, but I'll defer to other people to answer.
    3) The page peel is a transition built into FCE.

  • User Contributed Tips in the MacBook Pro (Late 2008) Power and Batteries

    *The following User Contributed Tips are located in the MacBook Pro (Late 2008) > Power and Batteries on a MacBook Pro (Late 2008) forum:*
    None at this time.
    *The following related tips are located in other areas of Apple Discussions:*
    neuroanatomist - Apple notebook batteries – maintenance and troubleshooting
    http://discussions.apple.com/thread.jspa?threadID=1764220
    Publish date: Oct 23, 2008
    Also see User Tips Library

    The management is quite easy. You can move your Documents, Movies, Music, and Pictures folders to another drive and then replace them in the original location with aliases.
    Select Mac Help from the Finder's Help menu and search for "alias." This will provide a help file on creating and using aliases.

  • User Contributed Tips, Power and Batteries, MacBook 13-inch Al (Late 2008)

    *The following User Contributed Tips are located in the MacBook 13-inch Aluminum (Late 2008) > Power and Batteries on a MacBook 13-inch Aluminum (Late 2008) forum:*
    neuroanatomist - Apple notebook batteries – maintenance and troubleshooting
    http://discussions.apple.com/thread.jspa?threadID=1764220
    Publish date: Oct 23, 2008
    *The following related tips are located in other areas of Apple Discussions:*
    Please see User Tips Library

    Go to Applications/ Utilities/ System Profiler, and select "Power" from the menu on the left. Copy and paste here what it says about your battery.

  • User Contributed Tips, Ports & interfaces on MacBook Pro (Late 2008 & 2009)

    *The following User Contributed Tips are located in the Ports and interfaces on the MacBook Pro (Late 2008 and 2009) Forum:*
    None at this time.
    *The following related tips are located in other areas of Apple Discussions:*
    a brody - June 8, 2009 MacBook and Pros myths and facts
    http://discussions.apple.com/thread.jspa?threadID=2032539
    Publish date: June 26, 2009
    See also the User Tips Library

    Thanks again for your help Rod!
    One of the first things I tried was different combinations of devices to see if it may have been the device just not powering up. The main device I use is an official Apple wired keyboard, because at home I connect my MBP to my monitor and use a separate keyboard and mouse. I have tried other devices too with the same result, they only work when the dock is connected. I have tried connecting my iPhone via USB cable, i have a 16GB SanDisk Cruzer flash drive, which only lights up if the dock is connected, and I have a 4 port USB hub with a power LED on it, which again only lights up when the dock is connected.
    I looked in system profiler, and it says the USB ports are there, but doesn't recognise any devices plugged in, other than the dock. However, when the dock is plugged in, for example, it recognises the Apple keyboard in the other port.
    I took two screen shots, one of system profiler without the dock plugged in (USB keyboard still plugged in but not showing up), and another of when I plugged the dock in.
    Without Dock:
    With Dock:
    It might be worth pointing out that the HDD dock has two USB ports on it, which is what is highlighted in the second pic.
    I have also tried rebooting the computer with devices already attached but with the same result again. I've tried booting it with the dock and the keyboard attached, with just the keyboard, with just the dock, but either way unless the dock is connected, nothing else will work via USB.
    I just want to say thanks again Rod, it's very kind of you to spend your time trying to help me, and it is really appreciated!
    I'm going to contact Apple support shortly and see if they can offer a solution, or see if I can send it in for repair, which I am reluctant to do seeing as it's my only computer
    Cheers!
    Gav

  • User Contributed Tips in The MacBook Pro Display (Late 2008) forum

    *The following User Contributed Tips are located in the MacBook Pro (Late 2008) > The MacBook Pro Display (Late 2008) forum:*
    None at this time.
    *The following related tips are located in other areas of Apple Discussions:*
    a brody - Using a second Mac as a display for a first
    http://discussions.apple.com/thread.jspa?threadID=1587927
    Publish date: July 7, 2008
    See also User Tips Library

    I bought this computer with no disks, upgraded to Lion
    Replacement System Discs can be obtained from Apple's Customer Support - US (800) 767-2775 for a nominal fee. You'll need to have the model and serial number of your Mac available. 
    If you're not in the US, you may need to go through the regional Apple Store that serves your location to find the contact number - http://store.apple.com/Catalog/US/Images/intlstoreroutingpage.html
    for some reason AHT wasn't installed
    AHT is included in system disc #1. 

  • User Contributed Tips in The MacBook Pro Display forum

    *The following User Contributed Tips are located in the MacBook Pro (Original) > The MacBook Pro Display forum:*
    <pending>
    *The following related tips are located in other areas of Apple Discussions:*
    a brody - Using a second Mac as a display for a first
    http://discussions.apple.com/thread.jspa?threadID=1587927
    Publish date: July 7, 2008
    See also User Tips Library

    A cracked screen (LCD) or the glass that covers the LCD? I'm a little confused what is cracked? Is your LCD operating with the crack?

  • User Contributed Tips, PowerBook G4 (15-inch Titanium) Power and Batteries

    *The following User Contributed Tips are located in the PowerBook G4 (15-inch Titanium) > Power and Batteries on a PowerBook G4 15-inch Titanium forum:*
    None at this time.
    *The following related tips are located in other areas of Apple Discussions:*
    neuroanatomist - Apple notebook batteries – maintenance and troubleshooting
    http://discussions.apple.com/thread.jspa?threadID=1764220
    Publish date: Oct 23, 2008
    See Also User Tips Library

    Cornelius:
    Thanks for the info. Today I was not connected to the internet, i had my sys preferences set to never sleep, never screen saver and about half way through ripping a DVD with handbrake, my powerpc G4, was back at the login screen!! I logged back in and everything was gone/shut down. I had a half ripped movie and all programs were shut down? Today I also ran apple hardware tests from the disk, techtool pro 4 and everything passed so i dont know why this keeps shutting down?? Is there anymore tests i can run from the OSX tiger disk? Heres what the console and sys log looked like after the restart:
    Console:Mac OS X Version 10.4.10 (Build 8R218)
    2007-09-03 17:45:29 -0500
    2007-09-03 17:45:30.411 loginwindow[1385] FSResolveAliasWithMountFlags returned err = -43
    2007-09-03 17:45:30.412 loginwindow[1385] FSResolveAliasWithMountFlags returned err = -43
    2007-09-03 17:45:38.231 SystemUIServer[1399] lang is:en
    Sys:
    Sep 3 17:39:17 -Computer /System/Library/CoreServices/loginwindow.app/Contents/MacOS/loginwindow: Login Window Application Started
    Sep 3 17:39:21 -Computer loginwindow[1385]: Login Window Started Security Agent

  • User Contributed Tips, PowerBook G4 17-inch Power and Batteries forum

    *The following User Contributed Tips are located in the PowerBook G4 17-inch > Power and Batteries on a PowerBook G4 17-inch forum:*
    None at this time.
    *The following related tips are located in other areas of Apple Discussions:*
    neuroanatomist - Apple notebook batteries – maintenance and troubleshooting
    http://discussions.apple.com/thread.jspa?threadID=1764220
    Publish date: Oct 23, 2008
    See Also User Tips Library

    Cornelius:
    Thanks for the info. Today I was not connected to the internet, i had my sys preferences set to never sleep, never screen saver and about half way through ripping a DVD with handbrake, my powerpc G4, was back at the login screen!! I logged back in and everything was gone/shut down. I had a half ripped movie and all programs were shut down? Today I also ran apple hardware tests from the disk, techtool pro 4 and everything passed so i dont know why this keeps shutting down?? Is there anymore tests i can run from the OSX tiger disk? Heres what the console and sys log looked like after the restart:
    Console:Mac OS X Version 10.4.10 (Build 8R218)
    2007-09-03 17:45:29 -0500
    2007-09-03 17:45:30.411 loginwindow[1385] FSResolveAliasWithMountFlags returned err = -43
    2007-09-03 17:45:30.412 loginwindow[1385] FSResolveAliasWithMountFlags returned err = -43
    2007-09-03 17:45:38.231 SystemUIServer[1399] lang is:en
    Sys:
    Sep 3 17:39:17 -Computer /System/Library/CoreServices/loginwindow.app/Contents/MacOS/loginwindow: Login Window Application Started
    Sep 3 17:39:21 -Computer loginwindow[1385]: Login Window Started Security Agent

  • User Contributed Tips, iBook G4 Power, Battery and your iBook G4 forum

    *The following User Contributed Tips are located in the iBook G4 > Power, Battery and your iBook G4 forum:*
    None at this time.
    *The following related tips are located in other areas of Apple Discussions:*
    neuroanatomist - Apple notebook batteries – maintenance and troubleshooting
    http://discussions.apple.com/thread.jspa?threadID=1764220
    Publish date: Oct 23, 2008
    See Also User Tips Library

    For anyone experiencing the same issues, I wanted to post a supplementary and final post on this issue.
    Several days in with the 253 cycle battery, I noted the following:
    1) The iBook breezed along with the power connected. Essentially it was back to its old self.
    2) Unplugged, it developed occasional freeze tendencies when the power dipped below 40-50%.
    3) The iBook passed every test I threw at it. I could find nothing obvious in any of the logs to suggest a hardware problem (other than a kaput battery).
    Almost certainly its probably a power issue although I suspect the HD may not have years of useful life. I swithered about replacing the battery with a new Apple battery, a NewerTech battery or another 3rd party replacement battery. After some thought, we bit the bullet and retired the iBook and we now have a white unibody MacBook. Depending on its saleability, the iBook may well be destined to live on as an entertainment device/traveling Mac as it is still a solid performer for lighter tasks.
    Upshot: when your iBook starts behaving weirdly, take a look at the battery health.
    Thanks
    Gareth

  • User Contributed Tips in the Mac Pro Displays and the Mac Pro forum

    *The following User Contributed Tips are located in the Mac Pro > Displays and the Mac Pro forum:*
    None at this time.
    *The following related tips are located in other areas of Apple Discussions:*
    a brody - Using a second Mac as a display for a first
    http://discussions.apple.com/thread.jspa?threadID=1587927
    Publish date: July 7, 2008
    See also User Tips Library

    You can use the two graphics cards, but it's only useful if you have more than two displays. It won't give you higher speed.

  • User Contributed Tips in the MacBook (Original) The MacBook Display forum

    *The following User Contributed Tips are located in the MacBook (Original) > The MacBook Display forum:*
    <pending>
    *The following related tips are located in other areas of Apple Discussions:*
    a brody - Using a second Mac as a display for a first
    http://discussions.apple.com/thread.jspa?threadID=1587927
    Publish date: July 7, 2008
    See also User Tips Library

Maybe you are looking for

  • Free Goods Promotions for Retail.

    Hi SAP Retail Xperts. Actually I am working with Promotions for retail industry, and I am using the transaction WAK1, in order to create them. Our client, work with free goods (exclusive bonus quantity) and I can see that the WAK1 transaction has a v

  • Is SAP ABAP suitable w.r.t. my qualification and experience ? If NOT, which would be a suitable alternative ?

    Hello SAP Cummunity, I am very much interested in take up SAP course but like everyone very much confused. Firstly let me tell a brief about myself, - I have graduated in Bachelor of Engineering (Biotechnology) - After B.E., I took up PGDM (Marketing

  • SAP Records Locking for preceeding documents in MM

    *Hi Experts,* Our client have a current requirement. They want that all the preceding documents to be locked once the subsequent documents are converted and posted. Eg- when PR converted to PO, PR to be locked or disable, PO converted to MIGO, PO to

  • Msg sending is failing..

    m using nokia e63 n frm last 2days m unable to send msgs..msgs r stored in outbox firstly it shows tht it ll resend bt aftr tht is get failed..same prblm i faced earlier also n formatted my cell n prblm was solved bt i cn't format my cell again n aga

  • Does font search find all texts in my movie?

    Hi, when opening my flash movie I get the message that some fonts are missing. When I try to search for the missing fonts in my movie the related texts are not found. I remember that the search feature doesn't always work 100% correct i.e. searching