User equivalence test failed (RAC setup in Windows)
I am trying to set up user equivalence between 2 nodes, following instructions from "Oracle® Database Oracle Clusterware and Oracle Real Application Clusters Installation Guide 10g Release 2 (10.2) for Windows"
The Administrator account on both nodes have the same password. But the test failed. I can't find any trouble shooting doc from metalink.
Anyone can help?
Thank you very much.
Laura
Hi, Try to create a domain account and this domain account should be explicitly set in the local admin group for each node.
Bye
also check Note:388730.1 that can help on windows.
Message was edited by:
Romain VILCOQ
Note:412118.1 is valuable also
Message was edited by:
Romain VILCOQ
Similar Messages
-
User equivalence check failed (RAC setup)
Hello All,
I am trying to set up user equivalence between 2 nodes, following instructions from "Oracle® Database Oracle Clusterware and Oracle Real Application Clusters Installation Guide 10g Release 2 (10.2) for Solaris Operating System (SPARC 64-Bit)"
I have created user accounts on both nodes, .ssh folder with appropriate permissions, dsa and rsa keys on both nodes, copied them to authorized_keys on halfway, and scp authorozed_keys to wabasca. Now I am able to do 'ssh wabasca date' and 'ssh halfway date' on each node without being asked for password or passphrase:
$ whoami
ora10gr2
$ hostname
halfway
$ ssh halfway date
Thu Oct 6 16:51:37 MDT 2005
$ ssh wapiti date
Thu Oct 6 16:51:11 MDT 2005
$
$ whoami
ora10gr2
$ hostname
wapiti
$ ssh halfway date
Thu Oct 6 16:52:04 MDT 2005
$ ssh wapiti date
Thu Oct 6 16:51:38 MDT 2005
$Yet, the CVU verification of user equivalence fails:
$ whoami
ora10gr2
$ hostname
halfway
$ /Oracle10/cvu/bin/cluvfy comp admprv -n halfway,wapiti -o user_equiv -sshonly -verbose
Verifying administrative privileges
Checking user equivalence...
Check: User equivalence for user "ora10gr2"
Node Name Comment
wapiti failed
halfway failed
Result: User equivalence check failed for user "ora10gr2".
Verification of administrative privileges was unsuccessful on all the nodes.
$If I can 'ssh <nodename> date' sucessfully what may cause the CVU check of user equivalence to fail? (I see that timing is off between these 2 machines...)
Thank you very much for your time.
DanielDIt turns out that CVU is also requiring scp to be in /usr/local/bin; the idiot thing doesn't even try to use the scp that's in the execution $PATH, and on Solaris ends up failing silently early in the script (when ssh is in /usr/local/bin and scp is not).
I was finally able to figure out what was foobar'ed by turning on the trace mode and reviewing the logs:
export SRVM_TRACE=true
cluvfy stage -pre crsinst -n tri1-ora1,tri1-ora2 -verbose
This leaves you with log files in the CVU installation directory, under [CVU_HOME]/cv/log/; in mine I found...
[Worker 0] [20:7:53:400] [RuntimeExec.runCommand:74] Calling Runtime.exec() with the command ; Fri Nov 18 20:07:53 GMT+00:00 2005
[Worker 0] [20:7:53:400] [RuntimeExec.runCommand:76] /usr/local/bin/scp ; Fri Nov 18 20:07:53 GMT+00:00 2005
[Worker 0] [20:7:53:400] [RuntimeExec.runCommand:76] -p ; Fri Nov 18 20:07:53 GMT+00:00 2005
[Worker 0] [20:7:53:401] [RuntimeExec.runCommand:76] /opt/oracle/cvu//cv/remenv/exectask ; Fri Nov 18 20:07:53 GMT+00:00 2005
[Worker 0] [20:7:53:401] [RuntimeExec.runCommand:76] tri1-ora2:/tmp//CVU_10.2.0.1.0.1_oinstall/exectask ; Fri Nov 18 20:07:53 GMT+00:00 2005
[Worker 0] [20:7:53:402] [RuntimeExec.runCommand:90] exec exception:/usr/local/bin/scp: not found; Fri Nov 18 20:07:53 GMT+00:00 2005
Whoever programmed this thing seems slightly naive about host environment checking. Also, the Sun ssh package by default installs ssh and scp in /usr/bin; it's pretty popular to install the 3rd-party package that goes into /usr/local/bin though... -
User equivalence check failed in solaris 10
Hi,
i am trying to install oracle clusterware on solaris10.
when i executed clusture varification utility , user equivalence test is failed.
each node have same username,userid,group id
and i configured SSH also using
exec /user/bin/ssh-agent
/usr/bin/ssh-add after generation of rsa and dsa keys and putting this to authorization file.
it is not asking password for ssh and scp after executing this command but again user equivalence check failed
but after logging of and do login again to oracle user its not working. then again i have to set ssh that is
exec /user/bin/ssh-agent
/usr/bin/ssh-add
wat else i have to check for this?
can sombody help me to solve thisUmesh Gupta wrote:
Thay are same, i have already taken care of that..
Node1:-
$ id oracle
uid=101(oracle) gid=300(oinstall)
Node2:-
$ id oracle
uid=101(oracle) gid=300(oinstall)
Please suggest..
Regards
Umesh$exec /usr/bin/ssh-agent $SHELL
$/usr/bin/ssh-add
on any one of the nodes
and check the output of cluvfy
also refer the link:-
http://download.oracle.com/docs/cd/B28359_01/install.111/b28263/crsunix.htm#BEHIHBBF
User equivalence check failed (RAC setup)
Edited by: rajeysh on Aug 18, 2011 7:09 PM -
RUNCLUVFY Result: PRVF-4007 : User equivalence check failed for user "orac
hello
try to run runcluvfy.sh I receive the following screen rac2 is passed but rac 1 is failed can sombody help me?
thanks
[oracle@rac1 grid]$ ./runcluvfy.sh stage -pre crsinst -n rac1,rac2 -verbose
Performing pre-checks for cluster services setup
Checking node reachability...
Check: Node reachability from node "rac1"
Destination Node Reachable?
rac2 yes
rac1 yes
Result: Node reachability check passed from node "rac1"
Checking user equivalence...
Check: User equivalence for user "oracle"
Node Name Comment
rac2 passed
rac1 failed
Result: PRVF-4007 : User equivalence check failed for user "oracle"
WARNING:
User equivalence is not set for nodes:
rac1
Verification will proceed with nodes:
rac2
Checking node connectivity...Check this older thread which has a lot of information on this:
User equivalence check failed (RAC setup) -
User equivalence check failed for user "oracle" while running cluvfy
Hi All,
I am getting User equivalence error as follows while executing cluvfy. I want to install CRS on this server.
oracle@node200$ ./runcluvfy.sh stage -pre crsinst -n node200,node201,node202
Performing pre-checks for cluster services setup
Checking node reachability...
Node reachability check passed from node "node200".
Checking user equivalence...
User equivalence check failed for user "oracle".
Check failed on nodes:
node202,node201,node200
ERROR:
User equivalence unavailable on all the nodes.
Verification cannot proceed.
Pre-check for cluster services setup was unsuccessful on all the nodes.
I have sucessfully configured ssh and able to do ssh from all the nodes without prompting for the password. Also oracle uid and gid on all the servers are same.
I also checked in .kshrc file and there is no tty entry in that file. and I have also setup /etc/hosts.equiv file on all the node.
I still get the user equivalance error. Can anybody help me in this ?
Regards,
Raj.Hi,
thanks.
i need some more help because first time i am working on RAC,
i am also having User equivalence check failed for user "oracle"
i got two machines, one is IBM machine and one is DELL machine installed with solais 10 (AIX installation). both machines are not connected by private network now. and no shared external HDD available now. it will take one week time to set up the HW. the user equivalence check depends the above two factors?
now public network is available and node reachability test "passed"
could you please tell me what may be the reason for the user equivalence check in my case. details are given below
i have oracle user in both machine. user creation done through SMC. home directory is /export/home/oracle
the following are the details.
1) $ ssh pc000905 id -a oracle
Enter passphrase for key '/home/oracle/.ssh/id_rsa':
uid=100(oracle) gid=300(oinstall) groups=301(dba)
$ ssh pc026376 id -a oracle
Enter passphrase for key '/home/oracle/.ssh/id_rsa':
uid=100(oracle) gid=300(oinstall) groups=301(dba)
2) user nobody exists.
3) all files n .ssh directory have same permissions.
4) ssh and scp is working with out password(rsa and dsa keys generated).
5) oracle user is using bourne shell
6)soft link of /usr/bin/ssh and /usr/bin/scp are created to /export/home/oracle/bin
7)ForwardX11 is "yes" in sshd_config
8) created a config file in .ssh directory and ForwardX11 is "no" in that file
8) umask =022 in both nodes.
error displaying is
$/export/gome/cluvfy/runcluvfy.sh stage -pre crsinst -n pc026376,pc000905
Performing pre-checks for cluster services setup
Checking node reachability...
Node reachability check passed from node "PC026376".
Checking user equivalence...
User equivalence check failed for user "oracle".
Check failed on nodes:
pc026376,pc000905
ERROR:
User equivalence unavailable on all the nodes.
Verification cannot proceed.
Pre-check for cluster services setup was unsuccessful on all the nodes.
$ -
Result: User equivalence check failed for user "oracle".
While installing on Solaris-10, ssh, rlogin, scp works fine.
Running runcluvfy.sh stage -post hwos -n rac-1,rac-2 -verbose returns the above error.
Result: User equivalence check failed for user "oracle".
ERROR:
User equivalence unavailable on all the nodes.
Verification cannot proceed.
/bin/ssh & /bin/scp is in use.Hello,
I am facing User equivalence check failed for user "oracle" error on my newly to be built RAC cluster.
The Oracle users have been created identically and ssh have been setup as per RAC installation manual.
Still I am facing the below problem. Please help me out
Node1 > uname -a
Linux purple-rac-node2 2.6.18-194.el5 #1 SMP Mon Mar 29 22:10:29 EDT 2010 x86_64 x86_64 x86_64 GNU/Linux
Node2 > uname -a
Linux purple-rac-node1 2.6.18-194.el5 #1 SMP Mon Mar 29 22:10:29 EDT 2010 x86_64 x86_64 x86_64 GNU/Linux
clusterware/cluvfy/runcluvfy.sh stage -post hwos -n purple-rac-node1,purple-rac-node2 -verbose
Performing post-checks for hardware and operating system setup
Checking node reachability...
Check: Node reachability from node "purple-rac-node1"
Destination Node Reachable?
purple-rac-node2 yes
purple-rac-node1 yes
Result: Node reachability check passed from node "purple-rac-node1".
Checking user equivalence...
Check: User equivalence for user "oracle"
Node Name Comment
purple-rac-node2 failed
purple-rac-node1 failed
Result: User equivalence check failed for user "oracle".
ERROR:
User equivalence unavailable on all the nodes.
Verification cannot proceed.
[oracle@purple-rac-node1 ~]$ id oracle
uid=501(oracle) gid=501(dba) groups=501(dba),502(oper),503(oinstall)
[oracle@purple-rac-node2 ~]$ id oracle
uid=501(oracle) gid=501(dba) groups=501(dba),502(oper),503(oinstall) -
CLUVFY failing with 'User Equivalence check failed for...'
New 2 node RAC configuration. Oracle 10gR2, Linux RHEL 5 x64. I'm at the post hardware config, pre install clusterware stage.
Running the cluster verification utility command:
cluvfy comp sys -n node-01,node-02 -p crs -verboseReturns the following error:
Verifying system requirement
ERROR:
User equivalence unavailable on all the nodes.
Verification cannot proceed.
Verification of system requirement was unsuccessful on all the nodes.I've verified the following:
1) RSA keys correctly configured on both nodes and I can ssh between without a password
2) ping ip and private work correctly to and from both nodes.
3) user, group ids are identical on both systems.
I also ran cluvfy stage -post hwos -n node-01,node-02 -verbose and received the following output. This output is from node-01. node-02's is identical, except with equivalence to itself failing.
Checking node reachability...
Check: Node reachability from node "node-01"
Destination Node Reachable?
node-02 yes
node-01 yes
Result: Node reachability check passed from node "node-01".
Checking user equivalence...
Check: User equivalence for user "oracle"
Node Name Comment
node-02 passed
node-01 failed
Result: User equivalence check failed for user "oracle".
WARNING:
User equivalence is not set for nodes:
node-01
Verification will proceed with nodes:
node-02
Checking node connectivity...I get the same behavior on both nodes. Not quite sure what else to check. Any thoughts or suggestions? Thanks.No, no banners. And I followed note 300548.1 to the letter. Several times :-)
However, I believe my issue has to do with a CVUHOME/cv/admin/cvu_config.
According to the documentation:
CV_XCHK_FOR_SSH_ENABLED—If set to TRUE, it enables the X-Windows check for verifying user equivalence with ssh. By default, this entry is commented out and X-Windows check is disabledIt was not, unfortunately, disabled by default - once I set it to false, everything succeeded. I still need to figure out why XCHK itself is failing, but I think I can troll through the log to figure that out. -
PRVF-4007 : User equivalence check failed for user "grid"
Oracle Version 11.2.0.3.0 patched to 11.2.0.3.1
I had installed GIU and RAC db on 2 node cluster
but since yesterdy has this issue when running the commands
[grid@vmorarac2 ~]$ cluvfy comp ocr -n all -verbose
Verifying OCR integrity
ERROR:
PRVF-4008 : User equivalence unavailable on all the specified nodes
Verification cannot proceed
vmorarac1 and vmorarac2 r the two nodes
as a grid user, from vmorarac1 i ran ssh vmorarac2 and it failed with above error and vice versa
so i did the following
from vmorarac1
ssh vmorarac2
yes and enter key
exec /usr/bin/ssh-agent $SHELL
/usr/bin/ssh-add
i did the same on other node
but the problem still exists.
Edited by: 912919 on 23-May-2012 06:58Hi,
The subject of thread "*PRVF-4007 : User equivalence check failed for user "grid*"
Now..
{code}
PRVF-4657 : Name resolution setup check for "vmorarac-scan.pbi.global.pvt" (IP address: 152.144.199.201) failed
PRVF-4664 : Found inconsistent name resolution entries for SCAN name "vmorarac-scan.pbi.global.pvt"
PRVF-4664 : Found inconsistent name resolution entries for SCAN name "vmorarac-scan.pbi.global.pvt"
{code}
If you can see are different issue.
If you are using DSN to resolve hostname "vmorarac-scan.pbi.global.pvt" check with "nslookup" if the name is resolved correctly.
If you are using Hosts File to resolve hostname "vmorarac-scan.pbi.global.pvt" you must configure only one ip (152.144.199.201) to resolve "vmorarac-scan.pbi.global.pvt" this entrie must be on host file of all nodes of cluster.
Levi Pereira -
User equivalence check failed for user "oracle".
Hi,
I am trying to install the Oracle Clusterware 10g as part of my RAC setup.
I have configured RHEL 4 in 2 nodes (rac and rac2). But when I run the runcluvfy utility, I get the below error:
[oracle@rac cluvfy]$ ./runcluvfy.sh stage -pre crsinst -n rac,rac2
Performing pre-checks for cluster services setup
Checking node reachability...
Node reachability check passed from node "rac".
Checking user equivalence...
User equivalence check failed for user "oracle".
Check failed on nodes:
rac
WARNING:
User equivalence is not set for nodes:
rac
Verification will proceed with nodes:
rac2
The problem is only with the first node(rac). The second node passes succesfully.
ssh works fine. Not sure what is wrong!
Thanks!Did you do Configure SSH for User Equivalence ?
Or
Did you Establish User Equivalence ?
If yes.. please check...
$ ssh rac hostname
rac
$ ssh rac2 hostname
rac2
You should Establish User Equivalence before...
exec /usr/bin/ssh-agent $SHELL
/usr/bin/ssh-add
If You don't configure ssh for user equivalence
http://www.oracle.com/technology/pub/articles/smiley_rac10g_install.html
Or
read SSH User equivalence is not set up on the remote nodes -
11g Cluster: User equivalence check failed on Node1 but passed on Node2,
From Node1:
[oracle@redhat4_1 bin]$ ./cluvfy stage -pre crsinst -n redhat4_1,redhat4_2 -verbose
Performing pre-checks for cluster services setup
Checking node reachability...
Check: Node reachability from node "redhat4_1"
Destination Node Reachable?
redhat4_2 yes
redhat4_1 yes
Result: Node reachability check passed from node "redhat4_1".
Checking user equivalence...
Check: User equivalence for user "oracle"
Node Name Comment
redhat4_2 passed
redhat4_1 failed
Result: User equivalence check failed for user "oracle".
WARNING:
User equivalence is not set for nodes:
redhat4_1
Verification will proceed with nodes:
redhat4_2
From Node2:
[oracle@redhat4_2 bin]$ ./cluvfy stage -pre crsinst -n redhat4_1,redhat4_2 -verbose
Performing pre-checks for cluster services setup
Checking node reachability...
Check: Node reachability from node "redhat4_2"
Destination Node Reachable?
redhat4_2 yes
redhat4_1 yes
Result: Node reachability check passed from node "redhat4_2".
Checking user equivalence...
Check: User equivalence for user "oracle"
Node Name Comment
redhat4_2 passed
redhat4_1 passed
Result: User equivalence check passed for user "oracle".
Why cluvfy failed on node1 but passed on node2? Thanks.Last time I saw that, the password-less SSH was working only in one direction. Root cause was not quite following the instructions to copy the authorized_keys to all nodes.
-
User equivalence check failed for user "oragrid" in HP-UX
Dear Friends,
while cluster verification utility i gotthe below error.
$ ./runcluvfy.sh stage -pre crsinst -n aeadsverp11-adp.adp.ae,aeadsverp12-adp.adp.ae -fixup -verbose
Performing pre-checks for cluster services setup
Checking node reachability...
Check: Node reachability from node "aeadsverp11-adp"
Destination Node Reachable?
aeadsverp11-adp yes
aeadsverp12-adp yes
Result: Node reachability check passed from node "aeadsverp11-adp"
Checking user equivalence...
Check: User equivalence for user "oragrid"
Node Name Comment
aeadsverp12-adp failed
aeadsverp11-adp failed
Result: PRVF-4007 : User equivalence check failed for user "oragrid"
ERROR:
User equivalence unavailable on all the specified nodes
Verification cannot proceed
Pre-check for cluster services setup was unsuccessful on all the nodes.
I had configred ssh and scp on both nodes.
$ ssh aeadsverp11-adp.adp.ae date
Wed Sep 28 04:26:55 MDT 2011
$
$ ssh aeadsverp12-adp.adp.ae date
Wed Sep 28 13:28:26 WAT 2011
ssh is wrking fine without any issues on both nodes.
Please advice.
Thanks,
RajendraHi,
Just ignore it and proceed with installation.
Its an bug.
Kind Regards,
Rakesh -
Result: PRVF-4007 : User equivalence check failed for user "oracle"
Hi
I get below error everytime I run ./cluvfy stage -pre crsinst -n node01,node02 -fixup -verbose > a.log
Checking user equivalence...
Check: User equivalence for user "oracle"
Node Name Comment
node02 passed
node01 failed
Result: PRVF-4007 : User equivalence check failed for user "oracle"
WARNING:
User equivalence is not set for nodes:
node01
Verification will proceed with nodes:
node02
node01 is the local node, if I run from node02 It comes back saying the same thing about node2!
I have checked oracle uid and groups all set correctly and ssh working fine ...
I have ran the same command for grid user and getting the same error !!i know what it was, i should have done ssh localnode date for once at least!!
I only did ssh remotenode date :) -
User equivalence check failed, both side say other node passed, why?
SPARC Soloris 10, clusterware 11gr1
two nodes cluster checking, both side say itself fail, other side is passed. why?
./runcluvfy.sh stage -pre crsinst -n bclabdb01,bclabdb02 -verbose
on node1(bclabdb0):
Checking user equivalence...
Check: User equivalence for user "crs"
Node Name Comment
bclabdb02 passed
bclabdb01 failed
Result: User equivalence check failed for user "crs".
WARNING:
User equivalence is not set for nodes:
bclabdb01
Verification will proceed with nodes:
bclabdb02
on node2:
Check: User equivalence for user "crs"
Node Name Comment
bclabdb02 failed
bclabdb01 passed
Result: User equivalence check failed for user "crs".
WARNING:
User equivalence is not set for nodes:
bclabdb02
Verification will proceed with nodes:
bclabdb01Hi
Which user equivalence you have configured rsh or ssh.If you have configured through ssh check it as oracle user through
ssh <nodename> <command>
if you have configure rsh then you need to create hosts.equiv file inside /etc/ and give proper permission to oracle user.Before installing clusterware I used CVU and its shown me passed for user equivalence .
Tinku -
RAC : User equivalence check failed
Hi All,
Platform linux CentOS 4.5 and oracle 10g.
I facing an issue with " user equivalence failed" while executing cluvfy command. On accessing node 2 from node 1 using ssh it is asking for password(oracle user) after configuring SSH. I have configured RAC earlier also but this time i could not figure out the issue with SSH.
I have removed SSH client and installed it fresh and try to configure however faced the same result.
Any help would be highly appreciated.
regards,
ShaanHi,
I have deletd ~/.ssh (rm -fr) directory which contained dsa,rsa,dsa.pub,rsa.pub and known_hosts. Yes i'm using vmware server 1.02.
I have configured RAC earlier using same vmware and os version.
key creation
=========
*both nodes
mkdir -p ~/.ssh
chmod 700 ~/.ssh
/usr/bin/ssh-keygen -t dsa
/usr/bin/ssh-keygen -t rsa
mkdir ~/.ssh/authorized_keys
from node 1
ssh node1 cat ~/.ssh/dsa.pub >> ~/.ssh/authorized_keys
ssh node1 cat ~/.ssh/rsa.pub >> ~/.ssh/authorized_keys
ssh node2 cat ~/.ssh/dsa.pub >> ~/.ssh/authorized_keys
ssh node2 cat ~/.ssh/rsa.pub >> ~/.ssh/authorized_keys
scp ~/.ssh/authorized_keys node2:.ssh/authorized_keys
exec /usr/bin/ssh-agent $SHELL
/usr/bin/ssh-add
Please let me know if i missed out any step
regards,
Shaan
Edited by: Shaan_dmp on Sep 14, 2009 2:56 PM -
Configure shared storage (RAC setup in Windows)
Hi,
Can I use mapped drive instead of direct connect to the external drive while configuring the shared storage?
My problem is:
I have a LaCie Group SA LaCie Big Disk Extreme LUN 0 IEEE 1394 SBP2 Device (500g). It can only be directly attached to one node because there is only one FW400 port. When I use switch and tried to connect both nodes directly to the device by switch, only one node show it as a disk drive. On another node, the device is utomatically stopped by windows and unaccessible.
Then I tried to map it, but the shared storage test failed.
Any idea?
Thanks
LauraHi.
I struggled with this problem, but then I gave up and used VMware to solve the problem:
http://www.oracle-base.com/articles/10g/OracleDB10gR2RACInstallationOnWindows2003UsingVMware.php
http://www.oracle-base.com/articles/10g/OracleDB10gR2RACInstallationOnCentos4UsingVMware.php
Howard Rogers has some stuff that might give you a clue also:
http://www.dizwell.com/oracle/articles/laptop_rac.html
Cheers
Tim...
Maybe you are looking for
-
How to remove the actions of ON-ERROR trigger.
Hi to All, I have this problem. In my form this is the code in ON-ERROR trigger: DECLARE Cur$Item VARCHAR2(100) ; Cur$NumMsg NUMBER := MESSAGE_CODE ; Cur$TxtMsg VARCHAR2(80) := MESSAGE_TEXT; BEGIN IF Cur$NumMsg = 40202 THEN
-
TAKE HOME TEST i need help with
Chapter 11 ? Arrays Continued Test CAN ANY1 HELP ME ANSWER THIS?? 1. A hair styling salon provides many services, The HairSalon class contains a String field to hold the type of service, a double to hold the price for that service, and a double to ho
-
Function element value in ARTMAS IDoc
Hi, My scenario is IDoc->Xi->File, my mapping is based on Function element (if the IDoc contains changes or new data) but all time I got just 005 as Function witch mean new article. Is there any set up to do in order to get 004 for changes and 005 fo
-
Hey my serial number didnt work
Hey I´m using premiere Elements 12 on windows 8. I bought the CD one year ago and install them. All perfekt but after i set back my Laptop to new and i want to install it, the number didnt work.... I have the bundle with Photoshop elements 12 and the
-
Can't run the latest Dev Days appliance on my Mac
I have just downloaded and installed Virtual Box on my Mac book, so I can run the latest OTN Developer Days VM. The import worked fine but when I tried to start up the image I got this error message: Failed to open a session for the virtual machine O