User Tracking supported for Nexus 5K in Prime Infrastructure 1.3
Hi,
Is User Tracking supported for Nexus 5K in Prime Infrastructure 1.3?
Regards
Francois Bouchard
Hi Andy,
Check the below link , as per this Doc .. User tracking is supported in 2.0:
http://www.cisco.com/en/US/prod/collateral/netmgtsw/ps6504/ps6528/ps12239/guide_c07-729089.html
Thanks-
Afroz
[Do rate the usefu post]
Similar Messages
-
I am about to turn up some new Nexus switches, and am curious if anyone else has tried using MARS to discover and collect syslogs from NX-OS. If you've tried it, what was your experience? Are the Nexus syslogs close enough to IOS syslogs to at least let MARS understand most?
If it's a no-go, is there planned support for NX-OS in an upcoming MARS release?
Thanks.I note Nexus syslogs are still not supported in CS-MARS v6.1.x Revised: January 27, 2011
With CS-MARS product now end of sale June 2011, should I hold out any hope of a fix before end of Software Maint in June 2012 ? -
Configure the syslog of ASA 5512-X for display on Cisco Prime Infrastructure 2.1
Hi, I'm working on implementing the Cisco Prime Infrastructure 2.1 and want to display the syslog about ASA5512-X with Software Version 9.2.
What would be the procedure for configuring?
Thanks in advance.Hi,
Enable "logging host x.x.x.x " command to enable logging
check the below link:
http://www.cisco.com/c/en/us/td/docs/security/asa/asa91/configuration/general/asa_91_general_config/monitor_syslog.html#68764
FYI: Prime Infrastructure support only SEV 0,1,2 syslogs as of now.
Operate > alarm and events > syslogs
Thanks-
Afroz
****Ratings Encourages Contributors ***** -
BT Infinity - Home User - No Support for anything ...
I was disgusted with BT support today as a home user, apparently they only support HTTP traffic, if you have problem with any other protocol, it's nothing to do with them. Firstly below is a typical speed test result for my line over the past week :-
Download speedachieved during the test was - 73.57 Mbps
For your connection, the acceptable range of speeds is 12 Mbps-0 Mbps.
IP Profile for your line is - 77.43 Mbps
Upload speed achieved during the test was - 17.07Mbps
Additional Information:
Upstream Rate IP profile on your line is - 20 Mbps
As you can see, no problems there ..... or so it would seem.
My problem is with NNTP Newsgroups. I pay for a newsgroup service, and my speeds over Infinity in the past 2 years have just been fine, alway maxing out my connection, whatever that might be at the time, depending on network loading, but usually in excess of 55 Mbits and I have been happy with it.
Around a week ago at about 12:30 AM, my speed dropped to around 7 Mbits. After rebooting PC, router, etc. with no change of speed, I assumed it to be a temporary fault or problem. Here I am today with the same problem, with highly variable NNTP speeds, but with ALL other protocols working fine at full speed, e.g http, ftp
Today my NNTP was generally under 1 Mbit, with little peaks to 2 Mbits, one short peak to 10Mbits, and a 60 second peak to 68 Mbits, before falling back into the under 1 Mbit range.
Things I have done :-
Tested on 2 operating systems (Windows 7 x64 Pro and Windows 8 x64 Pro)
Tested on 2 Routers
Tested on 2 pieces of premium Newsgroup software
Tested with 2 premium newsgroup providers (signing up for a trial account with the 2nd one)
Tested with firewall on and off (disabling loading on boot)
Tested with HTTP and FTP downloads
EDIT: Forgot to mention ports so I have added here to save anyone skipping fwd 2 posts
This is across all available ports and whether SSL is used or not.
SSL - 563, 443, 8080, 80, 81
STD - 119, 23, 25, 7000, 8000, 9000, 3128
I still have the mostly very low NNTP speeds, but full speed with other services.
After getting no joy with customer services in India, who didn't know what NNTP is, I spoke to technical support today, which is a premium service which I am charged for ..... don't know why!
They told me that newgroups is essentially a 'business' service, so they don't provide support. I said that it's standard network protocol just like ftp, http, pop3, emap etc. and for some reason it doesn't appear to be working correctly. I was told that I could submit a line speed fault, to which I replied that if I do that, BT will ask me to do the standard speed test which I assume is http, and I know that is working OK. I was told that in that case, there is nothing they can do.
I said, hold on, I have a website on a web server, and if I had trouble using ftp to to upload or download from that web server, would you help? No, I was told, we do not support FTP ....... eh?
So this means that I pay for other internet services, services that are transmitted across the BT network, but BT doesn't help or test if there is a problem with one of the standard protocols. For all I know NNTP could now be shaped by BT (I don't think that it is).
The high variabilty of the speeds, and that they tend to be on the very low side, says to me that some sort of network error maybe effecting that protocol .......... but I can get no help whatsoever, like it or lump it.
Any ideas anyone, as I have already had one week of wait and see, and there is no improvment. I don't want to lose NNTP, but I am not willing to pay for a premuim service that I cannot use, especially when BT Infinity unlimited is a premium service in itself.
BTW if BT still had their old FUP, I would still be well within their old fair usage limits.
CheersHi
Thanks for the link.
Yes, I read that thread earlier in the week, when I was researching whether they introduced shaping on NNTP.
As bittorrent is raised in the thread and whether news should be shaped or not (not my concern), I avoided posting in that thread.
I don't think it is shaping, because the speed is just too variable. I have been with the same news provider for 5 years or so. All through my ASDL 1, and ASDL 2 times, and with now Infinity for the past 2 years. I cannot see a reason why I have always been maxed out over that whole period (barring minor variabilty), that I should suddenly drop to between a 1/10th and 1/70th for most of the time, with sudden peaks that often drop away just as suddenly. That looks like a fault to me.
If I am sailing away at 68 Mbits, and it drops to 50 Mbits, I don't really care, because I know it will go up and down a bit depending on network loading. Under 10 Mbits and especially 1 Mbit is totally unacceptable (lowest speed of the day - 7 kbits) -
Cisco Multicast Manager Support for NEXUS
Hi All,
Does Cisco Multicast manager support Nexus devices ?
Please help.No at this time it does not according to the data sheets:
http://www.cisco.com/en/US/partner/prod/collateral/netmgtsw/ps6504/ps6335/ps6337/q_a_c67-527951.html
You can use cisco data center manager for managing Nexus devices:
http://www.cisco.com/en/US/products/ps9369/index.html
Download software:
http://tools.cisco.com/support/downloads/go/Redirect.x?mdfid=281722751 -
1) As per release notes DCNM 4.2 we cannot perform software/configuration/power management for Cisco Nexus 2k and 5k from DCNM.
Is there some other solution with which we carry out above task
2) Also can DCNM manage QOS and Multicasting on Nexus 7k/5k/2k or notI note Nexus syslogs are still not supported in CS-MARS v6.1.x Revised: January 27, 2011
With CS-MARS product now end of sale June 2011, should I hold out any hope of a fix before end of Software Maint in June 2012 ? -
No Fast User Switching Support for Windows XP ?????
I just got off the phone with Apple support and they confirmed that the iPod Nano and iTunes do not support fast user switching. What kind of joke is this?
Has anyone found a work around for this, having everyone log off so I can update my ipod is not an options!!!!
This is my first (and maybe last) Apple product.
iPod Nano Windows XP Fast User SwitchingActually it is a big problem, because I share the PC with my parents (who each log into their own account.) I would need to login to both of their accounts (and I don't have their passwords) exit all their open programs and then log them out. So not only does it take a while, they will kill me if I start doing that on a regular basis.
I cannot believe that iTunes doesn't work with multiple users logged in, every other program we have works properly this way. I have several friends who use their XP system in the same way with other family members.
This is really lame.
Does iTunes work this way with OS X? -
LMS 4.0, Support for Nexus VDC
Hi everybody,
Does LMS 4.0 support the management of Nexus 7000 VDCs?
I don't need it do be able to do anything complex. I was just interested in syslog, polling, and config fetches. I can poll and ping the management IPs of the VDCs from the command line of the server itself, but it stays questioned and "UNKNOWN" in the device list.
The admin context of the Nexus 7000s are being added just fine. We recently built 4.0, coming from LMS 2.6. LMS 2.6 appears to add the VDC to the DCR without issue, but 4.0 does not. I just want to make sure that I'm not missing something.
Thanks for the help!
TimHi everybody,
Does LMS 4.0 support the management of Nexus 7000 VDCs?
I don't need it do be able to do anything complex. I was just interested in syslog, polling, and config fetches. I can poll and ping the management IPs of the VDCs from the command line of the server itself, but it stays questioned and "UNKNOWN" in the device list.
The admin context of the Nexus 7000s are being added just fine. We recently built 4.0, coming from LMS 2.6. LMS 2.6 appears to add the VDC to the DCR without issue, but 4.0 does not. I just want to make sure that I'm not missing something.
Thanks for the help!
Tim -
Prime Infrastructure 2.0 and User Tracking
Hello
I'm having a look at getting wired User Tracking working on Prime 2.0. I checked that it is supported in the following link:
http://www.cisco.com/en/US/prod/collateral/netmgtsw/ps6504/ps6528/ps12239/guide_c07-729089.html
I'm having a problem getting dynamic user tracking working for wired non-802.1x clients. The switches are configured for mac-notification traps and the config works fine for LMS.
Another LMS User Tracking feature I'd link to get working in Prime 2.0 is CUCM intergartion where Prime would pull IP Phone extensions/names etc from CUCM.
Are either of these User Tracking features supported in Prime 2.0 (or at least roadmapped) or should I stick with LMS 4?
Thanks
AndyI am gettng good non-802.1x wired user tracking info. see the screenshot below (click to expand).
I don't have a CM so I can't comment on that bit.
Row 1 in the screenshot, for example, is confirmed with the following CLI output:
User_Access#sh run int fa1/0/41
Building configuration...
Current configuration : 177 bytes
interface FastEthernet1/0/41
description user access
switchport access vlan 10
switchport mode access
snmp trap mac-notification change added
spanning-tree portfast
end
User_Access#sh mac address-table | i 1/0/41
10 000f.b58e.3732 DYNAMIC Fa1/0/41
User_Access#sh inv
NAME: "1", DESCR: "WS-C3750-48P"
PID: WS-C3750-48PS-S , VID: V10 , SN: FDO1425X2M9
User_Access#sh ver | i bin
System image file is "flash:/c3750-ipservicesk9-mz.122-55.SE5.bin"
User_Access# -
Does Cisco Prime Infrastructure supports monitoring CPU,Memory, HDD for UCS , VMWare?
Prime Infrastructure/ Assurance is positioned today more towards managing network elements and network performance, rather than server infrastructure. We are in the process of adding Datacenter component support, with more focus on Nexus and UCS- due later this year.
Having said that, Prime Infrastructure allows the system user to add custom SNMP polling templates, which can then be used for polling any SNMP based values from any SNMP enabled device. These can be used to collect the information you specified below and the polled information will be available in dashboards and reports. -
Cisco Prime Infrastructure not detecting Nexus VLANs
Hello,
we recently added 2 Nexus 5010 to our prime Infrastructure 2.0.
Once synchronization is completed, the device shows as Managed.
When looking through the device details, everything seems to be ok, just when looking into the VLANs tab, it says:
"none detected".
In fact, there are quite a lot of vlans on this device.
Did anyone have a similar problem?
Thanks,
JörgHi Jorg,
I have checked and confirmed that Unfortunately this feature is not supported for NEXUS . I mean the VLAN information.
and I think "port-channels" are also not supported.
Thanks-
Afroz
[Do rate the useful post]
****Ratings Encourages Contributors **** -
Please provide support for Sony DSC-R1 RAW files
Dear Apple employee,
If by any chance you happen to read this topic, would you please forward this information to the Aperture team?
Some users need support for DSC-R1 Raw files in Aperture. Please do something.
Thank you.I can't believe that Apple can't take the time to support the DSC-R1...when I saw the new OS and 1.5 release I had high hopes, which gave way to dismay.
How can they support a so-so cam like the A100 and ignore the R1? I have Bibble Pro...they have no problem supporting the R1 and many other cams that Apple's radar can't seem to pick up.
This is really driving me nuts...Apple, how about listening to the rest of us?
Anyone for approaching Apple and/or the Aperture developers as a group? -
Hello,
A customer currently have 2,500 Cisco Prime Infrastructure Lifecycle device license using Prime Infrastructure version 1.2 and LMS 4.x. the customer wants to upgrade to Cisco Prime Infrastructure 2.0.
Does anyone know if it is possible to upgrade to version 2.0 without additional cost? the licenses from
Cisco Prime Infrastructure 1.2 has to be upgraded or we need only to rehost the VUDI.
Also could be possible to upgrade LMS 4.x to Cisco Prime Infrastructure 2.0?
thanks!The two features you mention are two big missing ones. Another is full syslog capability. I don't believe CiscoView or day one support via package updates is included either.
Another is less tangible - the depth of experience and documentation available for LMS vs. Prime Infrastructure (particularly the wired management features). I agree for wireless PI 2.0 looks good. Some new features are coming for wired that look promising but they are new as of PI 2.0 so I'm taking a wait and see on them.
I hope to get 2.0 up in my lab in the next week or so and will hope to be pleasantly surprised but that's seldom the case with a major new release. -
Cisco Prime Infrastructure 2.0 - Third Party NetFlow
Hi,
is it possible to collect on the Cisco Prime Infrastructure 2.0 NetFlows from Third Party Devices, like a SonicWALL Firewall?
I mean it is possible to poll SNMP informations from a third party device, so maybe it is also possible to get the NetFlow from this Device?
Best Regards,
Sven K.
Sent from Cisco Technical Support iPad AppHi Sven,
As per my understanding for 3rd party Only below thing are supported:
The following support level is available with Prime Infrastructure :
• Auto Discovery of a 3rd party Device
• Basic Inventory collection
• Basic lifecycle management of 3rd party device
• Ability to show traps and syslog for 3rd party devices
• Device reachability status polling
• Ability to load new MIBs & to create new monitoring templates
• For both Cisco and any SNMP device
More info is available in the link given below:
http://www.cisco.com/en/US/docs/net_mgmt/prime/infrastructure/1.2/release/notes/cpi_rn.html#wp75765
Thanks-
Afroz
[Do rate the useful post] -
Cisco Prime Infrastructure 1.2 - Remote FTPrepository Sizing Guide
Can anyone provide a link to a sizing guide for remote FTP repository for backing up Cisco Prime Infrastructure 1.2 to a remote FTP server?
A personal observation; In PI 1.1, with the small ova we were running around 300 AP's and I had noticable slowness and issues. At that time, TAC mentioned that I should go with the medium as it was a known problem Now, despite being on 1.2 and alot of the issues resolved (and now new ones), if faced with the need to start over and I could spare the hardware, I would still go with the medium. My personal opinion is that Cisco VM's require way to much. On the other hand, knowing that it's relying on a built in Oracle DB, which from my experience with virtual servers, databases in VM = bad, it's understandable. Not everyone agrees with this point from vm gurus to db geniuses, and I'm not a professional vm guy, just play one on tv, but personally i shove as much hardware as I can afford from my host at it if it's a db in a vm. This comes from being in an enterprise with multiple oracle db's in multiple vm environments. My 2cents.
Maybe you are looking for
-
Messages has replaced all my text with a load of letter A's in boxes. What is that all about. When I type a new one it is fine until I hit enter then the same thing applies. Has anyone a fix for this? Picture below, many thanks for your help. Jason
-
Can I use a different OS for different users?
I have a Macbook Pro running OSX Lion and it would be easier to have two seperate user profiles (Work & Personal) with the Work profile using Windows 7 and my personal profile using OSX Lion. Is this possible? I've considered and dismissed Parallels/
-
Need help finding an audio interface for my old ADAT
Hello, I've been using Cakewalk Sonar for about 3 years and recently purchased a Macbook Pro and am making the switch to logic. In Windows I was using a E-mu 1212m PCI audio card that was connected via lightpipe to a Behringer ADA8000 8-channel pream
-
Will LR3 automatically transfer keyword tags of photos created in PSE when importing the photos
Hi eveeryone, I am new to LR3. I would like to import all my photos into LR3 and all these photos have keyword tags that were done in PSE. Will LR3 automatically import the keyword tags too? If not, how would I do it? Much appreciate your feedback.
-
Mac Mail with Optimum VERY slow
Over the past few days downloading e-mail from Optimum On Line using Mac Mail has become VERY sluggish. A 4 MB e-mail with an attachment takes over 7 minutes to download!!! Yesterday it took over 30 minutes to download about 8 e-mails. Outgoing mail