Using 2nd APXBS as bridge & router?

I already have one Airport Extreme Dual Band N in my house. But in my TV room, I have several wired ethernet devices. I'd like to connect them all to one router and wirelessly connect to my existing WiFi network.
Is this the right way to go? The only bridges I've seen are single port, which means I have to connect a router to it (or put a bridge on each device). Lots of extra wires and power bricks. No thanks.
If a second base station can be used like this, it would save a lot of space.

Welcome to the discussions!
+If a second base station can be used like this, it would save a lot of space.+
The "neatest way to do what you want would be to add another AirPort Extreme Dual Band (AEBS) "n" router and configure it to "extend a wireless network".
Setup this way, the second AEBS would provide even more wireless coverage in the area where it was located, and the ethernet ports are active in this type of configuration on the device so you could connect 3 ethernet devices.
+Is this the right way to go?+
Well, an ethernet connection is always faster and more stable than a wireless connection. There are going to be compromises with wireless, but it could work well for your purpose.
The second AEBS will need to be located where it can receive a good, strong wireless signal from your main router because your ethernet devices will be depending solely on a wireless connection to function correctly. If you are talking about downloading and streaming hi- definition video, gaming over the internet, etc, wireless may be "iffy".
Before you do anything, I suggest that you download a utility like iStumbler on you laptop. Position your laptop where the second AEBS would likely be located and take some signal strength and noise measurements at that location. If you don't see at least 50-60% signal strength with 10% or less noise, wireless may not provide the performance that you want.
I have a very good wireless signal at my house with multiple access points, but found that in order to download movies with DirectTVs On Demand service, I got much better results with a straight ethernet connection instead of wireless. DVD firmware updates run much quicker as well. But, your mileage may vary.
In that case, you will need to either run an ethernet cable to the other devices and install an ethernet switch at the location, or if running an ethernet cable is not possible, take a look at ethernet powerline adapters to accomplish the same task by using the AC wiring in your home to transmit the ethernet signal. Some adapters now include a built in switch so you can connect 3-4 devices neatly without adding an additional switch. Post back if you need more info on this option.
Might be a good idea to check with the store to understand their return policy in case things don't work as hoped. If you decide to try the second AEBS, please post back to let us know how things are working.
Message was edited by: Bob Timmons

Similar Messages

  • Can i use time capsule as the router with sky broadband

    how do i use time capsule as the router. I contacted my internet provider  which is Sky who had no info other than to suggest trying a sky forum.

    It depends on the type of modem they gave you.. and if you can bridge it.
    I suspect you cannot use the TC in router mode with sky.. but tell us more.. if it is adsl and they accept pppoe then you can get it to work.. otherwise no.. just use the TC in bridge.

  • How do I use AO update in the Route signal.vi

    Hi support,
    My goal is to create a waveform (to buffer it) and output it using the analog card (PCI-6713) N times and with the frequency F. Apperanlty this is done using a (actually 2) digital counter(s) on the PCI-6602 card.
    This is done using route signal.vi using "AO update". However I have not managed to get it working. I only get error -10341. So my questions are how do I do it? More specificly how do I use AO update in the Route singal.vi Do I need to conect the cards in any perticular way (cabels or so)? Also do you have more information about how the vi route signal works (the help file does not help me much)?
    Grateful for all help.
    I'm using labview 6.0 as developpement platform, and using the PCI-6601, PCI-67
    13 and a PCI-7344 cards. Since the program is quite large I will only send a portion of it, the pulseGen is supposed to generate the waveform (loaded as a text file, also submitted) the digital output used is in case 1 (in pulseGen) the analog output is in case 3. The MissingWaveform.vi is just to ensure that a waveform is supplied to the pulseGen.vi
    Sorry about the mess.
    /Chatri

    Cabling and Interfacing between Boards: You have capability for direct simultaneous connection between 6713 and 6602 (also 6601) via the RTSI bus, but you need to get a cable to connect between the boards. You can connect between the boards using the I/O pins of their respective signal conditioning hardware. These connections are slower. There are also PFI (Programmable Function Interfaces) connections that are set within the VI's.
    All that said, it is not obvious why you want to use the RTSI. You can use the PCI-6713 to generate AO. Presumably you have some signal conditioning accessory; which ever pin of that accessory the AO appears on, you wire it over to the SC accessory for the 6601 and the appropriate pin for the counter gate or
    source you want to use.
    Suggestions: Don't try to work in the context of your big VI for now. Get the AO bit and the counting bit to work together by themselves. Then shoe-horn them into the big VI. Also, consider a call to the NI help line. They are very good. 800.433.3488 (800IEEE488)
    In case you hadn't noticed the DAQ cards and Counter/Timer cards come in different flavors and there are specific example VI's to suit. 6602 uses NI-TIO chip, but PCI-671X are DAQ-STC. Again the NI help people are good at catching this kind of stuff.
    Your question is rather large and hard to manage. Perhaps if you break it down into small chunks the advise will be more free flowing.
    mike

  • My itunes 11 Home sharing is not working with my windows 7 PC and iPad it shows up on iPad and when I go to share the music app does loading for 3 mins and crashes I am using a virgin super hub router please please please help

    My itunes 11 Home sharing is not working with my windows 7 PC and iPad it shows up on iPad and when I go to share the music app does loading for 3 mins and crashes I am using a virgin super hub router please please please help

    My itunes 11 Home sharing is not working with my windows 7 PC and iPad it shows up on iPad and when I go to share the music app does loading for 3 mins and crashes I am using a virgin super hub router please please please help

  • New to FiOS, can I use my own modem and router

    I saw several questions similar to mine, but none that I saw answered my question for my scenario. I am sorry if this is a duplicate. I am new to FiOS. I have no other services from Verizon and do not plan to get any. No phone, no television, nothing. Just Internet. God willing, the installation will take place in two days. My house already has coaxial cabling. I have my own cable modem, a SURFboard SB6121, which goes to my router, a TP Link TL-WR941ND. None of my equipment advertises that it is FiOS compatible. I've seen other people asking about using their own modem and router, but in those cases the scenario involved other bundled services, and I understand a FiOS router is necessary to forward ports to television, phone, and computers. However, in my very simple scenario, can the Verizon optical network terminal simply feed its output to my coax, from there to my modem, then router, then comptuers? Is there any reason that wouldn't work? Verizon technical support just gave me a machine that wanted to help me troubleshoot my Internet connection, and I couldn't get from there to a human. Thanks in advance for the help!

    Banish the word and the device called "modem" from your home when using FiOS.  FiOS does not use modems.  Your cable modem is useless with FiOS.  Do not plug it in. FiOS uses routers.  The router connects to the ONT's WAN port using MoCA (coax) or Ethernet.  The installer will enable one of the ONT's WAN ports.  If you order 150Mbps or higher speeds, they will have to use Ethernet.  For slower speeds, coax is the default.  Many installers will use Ethernet if you ask nicely, but usually only if it isn't too much work.  Make sure it's easy to connect a router to the ONT using Ethernet, and you should be okay.  If Ethernet needs to be run through the walls, your best choice is get it done ahead of time.  You can always call later and get the ONT's WAN port switched. The only routers available with a MoCA WAN port are the Verizon models.  The Verizon routers are good devices for most users.  People who like to tweak their networking gear don't like them as many advanced features are limited or locked down.  You can't run any other router firmware on them.  WiFi range is decent, but not great.  I'm quite happy with my Quantum router.  YMMV. If you get Ethernet WAN enabled, you can use any router you want.  However, know that Verizon provides zero support for any other router.  They won't even mention it as an option.  That doesn't mean you can't use one, simply that you must do so without Verizon's help. There are reports that they won't even complete an install without one of their routers to verify service.  If you don't use one of their routers, consider renting one for a month to complete the install or even buying a used one.  If you own a Verizon router, you can install it if you ever suspect Verizon networking issues.  This will allow you to call their support. This FAQ is very helpful:http://www.dslreports.com/faq/16077 Good Luck. 

  • I want to set up my Epson printer using an airport and RR router. It was previously set up using a different router through HTC but same printer. How do I do this?

    I want to set up my Epson printer using an Airport and RR router. The same Mac Book and printer was formerly set up using a HTC router. How do I reset computer so it communicates with printer?

    http://support.apple.com/kb/HT3771
    Mac 101: Printing (Mac OS X v10.6)

  • HT201269 My iphone contacts are not updating to Icloud, I can create a contact in Icloud and it will update to my phone but I cannot create a contact on my phone to have it update in the cloud, I am using Itunes as the bridge

    My iphone contacts are not updating to Icloud or Outlook, I can create a contact in Icloud/Outlook and it will update to my Iphone but I cannot create a contact on my Iphone to have it update in the Cloud/Outlook, I am using Itunes as the bridge. I originally installed the Icloud manager to sync my contacts to Cloud/Outlook, but I did not like the functionality, when I uninstalled the Cloud manager and and installed Itunes I noticed that the none of my contacts in the phone updated to Outlook.
    Thanks in advance.

    Hi Cyclops12,
    Welcome to the Support Communities!
    The article below may be able to help you with this.
    iCloud: Troubleshooting iCloud Contacts
    http://support.apple.com/kb/ts3998
    Cheers,
    - Judy

  • I just bought a new iMac and I am using a apple air port router.  How do I connect mt windows PC to the air port router do I can move files

    I Just purchased a 21.5 iMac and connected it to the Internet using a apple air port router.  How do I connect my windows PC to my air port router so I can transfer files.

    It makes life easier to install the airport utility for windows.. which has a couple of different apps in it.. if you airport is new type then the utility is too old.. but is still valuable for Bonjour which provides network information for shared devices in the apple world to windows.. and a disk access agent..
    It will also help the Apple computer access shared directory in the windows computer.. nowadays this is pretty easy.

  • Using D-Link DI-624 Router for "G" Wireless Purposes

    I want to use an old D-link router in another part of the house to provide wireless "G" connectivity to my older devices, so I can use 5 GHz band for "N" connectivity exclusively via my Airport Extreme (Older version, not Gigabit).
    I go upstairs, plug the D-Links WAN port to the jack that connects to one of the Airport Extreme's LAN ports downstairs. I shut off dhcp server on the D-Link. I turn on the D-link's wireless capability (unencrypted for now, just for testing).
    When I plug a computer in to one of the LAN jacks of the D-Link, I have full connectivity to the internet. And I see the wireless signal from the D-Link which has a unique SSID. Unfortunately, while I can connect to the D-Link wirelessly, I cannot get to the internet.
    I'm sure I have something configured wrong.
    Questions:
    1. I have the Airport Extreme set to hand out ip addresses in the 10. range. Should I set up the D-Link router to get a static IP address from the Airport Extreme? How do I do that. Some sites suggest a 10 series IP address, but outside the range of the DHCP addresses that the Airport Extreme usually hands out.
    2. Any ideas on configuring the DI-624? I've shut off DHCP server (everyone says to do that). But Are there any other settings?
    3. Some tech help sites suggest not using the WAN Port at all on the D-link, but rather, connect to one of the LAN ports. Does this make any sense? Going from one of the LAN ports on the Airport Extreme to one of the D-Link's LAN ports.
    4. Once I get the wireless G network running, I'll fix the encryption.
    I think that in order to answer this question you'll need some first hand knowledge of the DI-624. Unfortunately, the DI-624 is now a discontinued product and there is little information available on D-link's web site.
    Thanks in advance for any advice.
    kenny

    If a Mac plugged into a LAN port on the D-Link gets internet access, the AirPort Extreme base station (AEBS) and D-Link are both configured properly.
    The wireless side of the D-Link should also be acting properly since LAN access is working.
    The most likely problem is that your Mac has incorrect DNS information in the System Preferences->Network preference pane->AirPort area.

  • I have a hard drive for CD storage that needs to connect to the Ethernet router. sInce my router is not in this room, and in another room, I want to use my Mac as a router for the drive, and share the wifi. Ho do I do this

    I have a hard drive for CD storage that needs to connect to the Ethernet router. sInce my router is not in this room, and in another room, I want to use my Mac as a router for the drive, and share the wifi. Ho do I do this? I gace tried the System Preferences -> Sharing, shared internet to Ethernet, but can't se ethe device on Finder

    Djembe wrote:
    UEFI (unified extensible firmware interface) boot requires Global unique identifier Partition Table (GPT) as opposed to the older Master Boot Record (MBR). If your existing drive is formatted in MBR, you will need to adjust BIOS settings to enable legacy boot in order for it to work properly.
    Is there a performance difference between GPT and MBR? If GPT is better, I do not mind formatting the drive with it.
    5. No special drivers are needed.
    Thanks. What about the thunderbolt port?
    7. I think Lenovo estimates 6 hours.
    Lenovo says 6 hours with the 6-cell battery on its website.
    BrendaEM wrote:
    Hi,
    There was a serious BIOS/UEFI problem with that SSD . Perhaps this thread will save you some headaches. Someone is recomending shutting off Rapid Boot in the setup, which would probable mean little with a SSD, anyway.
    I read through this, and it looks like the problem was fixed in a BIOS update, which I plan to do. However, it also seems like Intel Rapid Start is not even worth it in the first place, as sleep consumes almost no power at all.
    W540: i7-4700mq, K2100m, 8 GB DDR3L, 512 GB SSD
    T510: i7-620m, NVS 3100m, 8 GB DDR3, 512 GB SSD

  • Using libraries vs. Bridge for graphics in placeholder frames

    Hi,
    I do not understand the advantanges of using libraries vs. Bridge for my purpose:
    Purpose:
    I am working with templates using graphic placeholder frames. The frames are anchored in table cells and have object styles applied defining e.g. the placement of the graphic within the graphic frame.
    I want to set up central graphic library for all graphics used in all my documents.
    The graphics should then be linked into the documents
    Idea:
    set up various InDesign libraries and then drag the graphics into the placeholder frames. Then, when the graphic needs to be changed, do the changes in the library and have all my documents updated at once.
    Problem:
    Dragging graphics from the library into the placeholder frames does not seem to work. They are simply placed onto the page and NOT in the graphic frame. On the other hand when I simply store the graphics in various subdirectories in my file system and drag the graphics onto the page using Adobe Bridge, they ARE placed in the graphic placeholder frames.
    The library therefore seems a disadvantage, so why should I use a library instead of the Bridge?
    Also, will be upgrading to CS5 soon an want to use the live-linking caption feature. Should I use libraries or the Bridge approach?
    Stumped on this issue

    I like the idea with the snippet, but when dragging a snippet from Bridge there is still the same problem as with the library item: The graphic is NOT placed into the graphic placeholder frame of my template but is a free-flowing new graphic item which has to be placed manually.
    Interestingly, a JPG-file simply saved in the filesystem and dragged from Bridge and dropped over the placeholder frame WILL place the JPG into the frame!
    Why won't snippets do this??

  • Hello my name is jose quant, and let me know how I can use CAMERA RAW adobe bridge because the bridge use and want to open a camera raw image, I get a message that says: MAIN BRIDGE aplicaion NOT ACTIVATED. BRIDGE REQUIRES A PARTICULAR PRODUCT HAS BEGUN A

    Hello my name is jose quant, and let me know how I can use CAMERA RAW adobe bridge because the bridge use and want to open a camera raw image, I get a message that says: MAIN BRIDGE aplicaion NOT ACTIVATED. BRIDGE REQUIRES A PARTICULAR PRODUCT HAS BEGUN AT LEAST ONCE TO ACTIVATE THIS FEATURE. I wonder what that means?
    I use a lapto (windows 7) 64-Bit operating system.
    Thank you,
    my email is: [email protected], if you send me the answer to my query

    You need to activate Photoshop.
    Mylenium

  • If I own Adobe Photoshop Elements 12 and have it installed on my computer, how can I get access to Adobe Bridge without a monthly subscription?  Is there a way to use Adobe Photoshop and Bridge without paying a monthly fee?

    If I own Adobe Photoshop Elements 12 and have it installed on my computer, how can I get access to Adobe Bridge without a monthly subscription?  Is there a way to use Adobe Photoshop and Bridge without paying a monthly fee?

    Hi Jaclyn2,
    Please follow the steps mentioned in the kb: http://helpx.adobe.com/creative-suite/kb/error-update-server-repsonding-cs4.html .
    Regards,
    Romit Sinha

  • Colour washed out when using image processor in Bridge CS6

    Hi there
    I hope somebody can help please?!
    I am editing raw files in Camera Raw 8.2, then using image processor through Bridge CS6 to save them as both jpegs and tiffs.
    I am finding the colour on the saved files is coming out a little washed out and faded.
    If I open them individually and save them in PS6 as jpeg and tiffs, the colour remains vibrant and true to the original raw file.
    I have thousands of these files to go through and don't have time to open each one individually in this way so I am desperate to automate this process while still retaining the great colour in the original shots.
    Can anyone tell me why the shots are coming out this way and help offer a solution for me please?
    Any advice would be massively appreciated!
    Many thanks
    Benny P

    Hi,
    Do you have Include ICC Profile checked at the bottom of the Image Processor dialog?

  • Using macbook as a wireless router for non-apple devices

    im trying to use my mac as wireless router for my xbox. i went into share under system preferences, and made a network with a WEP password. I can see the network on my xbox but it requires an IP adress...
    i guess what im really asking is, if the mac can automatically assign IP adresses to devices on the network

    I use my MBP regularly to share internet connection with PCs. Usually the PCs do a 'search' for a network and then 'connect' to the network name set in the Airport options... drop down panel. They get the IP automatically.
    In the system preferences>share> there is a button on the right bottom which says 'airport options..' and in the drop down panel, you set the name or SSID and the WEP key.
    Maybe you should check XBOX settings if the network settings are manual or automatic?
    Hope that helps.

Maybe you are looking for