Using 802.1x and 2 hosts (one physical and one virtual) on the same port

Hello,
We trying to utilize the following scenario:
BYOD with users' windows based laptops and Apple Mac Books
Virtual machines within each of the physical machines: For Windows, the VMs will be Windows 7 VMs running within VM Workstation. For Macs, users will be running Windows 7 VMs within Fusion.
802.1x set for multi-host
Using 802.1x, we have a guest network that places the user's physical machine in once it fails authentication. The virtual machine runs the corporate image, and we'd like to have this VM connected to our corporate VLAN.
We have been running into this scenario though:
1.     User plugs his BYOD laptop from into the network. His laptop gets attached to the guest network because it fails the 802.1x check.
2.      The VM is powered on. It successfully is connected to the corporate network.
3.      Now, the user unplugs his network cable from his host machine and waits 10 seconds.
4.      He then re-plugs the network cable to his host machine.
5.      The VM is the first to authenticate to the 802.1x network and it gains access to the corporate network.
       6.      Due to the VM being the first to authenticate on 802.1x, the host network connection piggybacks off of the VM, and therefore the host gains access to the corporate network
Obviously this represents a no-go if the user's BYOD computer is able to access the corporate network. Is there is any specific way that 802.1x can be configured to prevent this from happening?
Thanks,
Mooge

Multi-Host is not the right option for you. In this Multi-Host only one device has to successfully authenticate to authenticate all device on that port.
You need to set host-mode to "multi-auth"

Similar Messages

How to Create Primary DB and Physical/Logical Standby DB on the same host?

Now I encounter a issue. I want to create one Primary DB and one Physical standby DB and one Logical standby DB on the same host.
Create this env on the same host aims to test whether we can using EM Patching DP to apply patches on Primary/Physical/Logical DB successfully.
I try to setup this env but fails. I want to know more related issues about create Primary DB /Physical DB/Logical DB on the same host and how to configure between them.
Below steps is my try:
1. Create Primary DB on the /scratch/primary_db
2. Create Physical Db software only on the /scratch/physical_db
3. Create Logical Db software only on the /scratch/logical_db
4. Using EM Wizard to create physical standby database and logical standby database, and these two targets can show up on the "All Targets" Page.
5. But when using EM Patching DP, it fails and the reason is the listener of physical and logical db cannot configured well.
Issues:
So I want to know about how to configure physical db and logical db's listener using EM or manually?
If the listener name of Primary Db is LISTENER and the port is 1521,and the listener.ora is under the /scratch/primary_db/network/admin directory, then how to config physical db and logical db's listener's name and port?

Hi,
As this a test case then you need to create two more listener for each Oracle Home (/scratch/physical_db & /scratch/logical_db) make sure that they have different names and ports.
Then add the new listeners manually using GC?
Try it and let me know
Regards
Amin

How do I set upmy Imac to allow using both my computer speakers and a Bose SoundLink system as outputs at the same time. I can use one or the other, but not both.

how do I set up my Imac to allow using both my computer speakers and a Bose SoundLink system as outputs at the same time. I can use one or the other, but not both. From systems Preferences I must select one or the other. I want both to work all the time.

Hi,
I would recommend you to use 0FI_AP_4 rather using both, particularly for many reasons -
1. DS: 0FI_AP_4 replaces DataSource 0FI_AP_3 and still uses the same extraction structure. For more details refer to the OSS note 410797.
2. You can run the 0FI_AP_4 independent of any other FI datasources like 0FI_AR_4 and 0FI_GL_4 or even 0FI_GL_14. For more details refer to the OSS note: 551044.
3. Map the 0FI_AP_4 to DSO: 0FIAP_O03 (or create a Z one as per your requirement).
4. Load the same to a InfoCube (0FIAP_C03).
Hope this helps.
Thanks.
Nazeer

Can I pair and use more than one set of bluetooth speakers at the same time on my ipod touch 4.0

can I pair and use more than one set of bluetooth speakers at the same time on my ipod touch 4.0 or Iphone 4s or Ipad 2?

You can only connect to one device at a time using Bluetooth, See article below for more information.
http://support.apple.com/kb/ht1664
While your iOS device can maintain multiple pairing records, it can only connect to one headset or hands-free device at a time. This prevents your iOS device from sending your data to the wrong Bluetooth accessory.

We have multiple devices in our family. On each iPad/iPhone each user has their own apple id for iMessage, Facetime and icloud, but we all sign in to the same apple id for itunes. When one of my kids comments on my shared photostream, it shows my name??

We have multiple devices in our family. On each iPad/iPhone each user has their own apple id for iMessage, Facetime and icloud, but we all sign in to the same apple id for itunes. When one of my kids comments on my shared photostream, it shows my name and not theirs as the commenter. How do I fix that?

CREATE A NEW USER
Go to System Preferences --> Create a New User in Users & Groups
Decide on whether to setup as Admin or Standard User.
Switch to the New User by logging out under the Apple in the Menu Bar or use Fast User Switching
Fast User Switching allows other users to leave current applications and windows open. Depending on RAM, you might need to log out rather than use FUS.

Is it possible to use both an ILB and an ELB (listening on the same port) in the same Azure cloud service?

I'm building a test Lync deployment on Azure; yes, I know this is not supported, hence "test".
Lync Front-End servers expose two set of web services, one for internal users and one for external ones; they listen on different ports (443 and 4443) on the same servers; when external services are published, you need a reverse proxy or a port forwarding
in order to map port 443 of a public IP address to port 4443 of the Front-End server(s). When you have multiple Front-End servers in a pool, you also need to load-balance them.
So, a typical Lync deployment looks like this:
       Internal users
               |
               443
                  |
          Internal LB
        192.168.0.20
        443         443
          |               |
   Lync FE 1     Lync FE 2
192.168.0.21 192.168.0.22
          |               |
      4443        4443
          External LB
       Public IP Address
                 |
              443
                 |
       External Users
This should be easily replicated in Azure, as it supports both external load balancing and internal load balancing. They are even supported together in the same cloud service, so this configuration should be easy. However, it looks like "should"
is the keyword here.
After creating the external load balanced endpoint (which listens on external port 443 and forwards to port 4443 on the servers), I'm trying to create an internal load balancer and add internal endpoints to is; however, while the ILB can be created successfully,
adding an internal endpoint listening on port 443 and forwarding to port 443 on the servers fails miserably, with an error stating that port 443 is already in use by another endpoint:
Update-AzureVM : BadRequest : Port 443 is already in use by one of the endpoints in this deployment. Ensure that the port numbers are unique across endpoints within a deployment.
For reference, my commands are:
Add-AzureInternalLoadBalancer -InternalLoadBalancerName "LyncILB" -ServiceName "LyncFrontEnd" -SubnetName "LabSubnet" -StaticVNetIPAddress 192.168.0.20
(This completes successfully)
Get-AzureVM LYNCFE1 | Add-AzureEndpoint -Name "Https-Int" -Protocol "tcp" -LocalPort 443 -PublicPort 443 -LBSetName "HttpsIntLB" -DefaultProbe -InternalLoadBalancerName "LyncILB"
(This fails)
The existing external endpoint is configured as such:
Get-AzureVM LYNCFE1 | get-azureendpoint
LBSetName : HttpsExtLB
LocalPort : 4443
Name : HTTPS-Ext
Port : 443
Protocol : tcp
Vip :
ProbePath :
ProbePort : 4443
ProbeProtocol : tcp
ProbeIntervalInSeconds : 15
ProbeTimeoutInSeconds : 31
EnableDirectServerReturn : False
Acl : {}
InternalLoadBalancerName :
IdleTimeoutInMinutes :
LoadBalancerDistribution :
The error doesn't even make a lot of sense; the external load balancer listens on a public IP address, while the internal load balancer listens on a private IP address in the internal network; there
shouldn't be any conflict here... however it looks like there is one instead.
Why doesn't this work? Am I doing something wrong, or is Azure networking just being silly as usual again?

Hello Massimo Pascucci,
The issue that you are facing when creating an endpoint with internal loadbalancer is the limitation of not allowing same ports to be listening under a single cloud service. This reason for this is that there is a limitation of only one private IP (Also
known as the Internal load balanced IP) per cloud service.
There is also a limitation on the Internal load balancer more than one port to be published per load balancer:
You can leave your feedback by following the link below:
https://social.msdn.microsoft.com/Forums/en-US/1805c5a0-3906-4cd6-8561-9802d77e0ae5/is-it-possible-to-use-both-an-ilb-and-an-elb-listening-on-the-same-port-in-the-same-azure-cloud?forum=WAVirtualMachinesVirtualNetwork
Refer to this article for more information on Internal load balancer:
http://azure.microsoft.com/blog/2014/05/20/internal-load-balancing/
Thanks,
Syed Irfan Hussain

How can I use the "Copy and paste" tool in order get stamps in the same position in different pages (Acrobat XI for PC)?

With Acrobat 6.0 I was able to copy a stamp in the same position (I mean "exactly" the same one) of different pages just by using the "copy/past" tool.
Now I am using Acrobat XI and it seems like it is not possible anymore: I am copying a stamp and I am trying to past it in anoter page, but it appears in the center of the page (or wherever it wants to...).
Does anyone have a solution?
Thanks in advance.

Thank you very much. I'll be waiting for you message.
Messaggio originale----
Da: [email protected]
Data: 26/01/2015 17.56
A: "Umberto Gangi"<[email protected]>
Ogg: How can I use the "Copy and paste" tool in order get stamps in the same position in different pages (Acrobat XI for PC)?
    How can I use the "Copy and paste" tool in order get stamps in the same position in different pages (Acrobat XI for PC)?
    created by Gilad D (try67) in Creating, Editing & Exporting PDFs - View the full discussion
Well, I was in the same situation so I've developed a tool that allows one to do it. I will send you some additional information about it in a private message.
     If the reply above answers your question, please take a moment to mark this answer as correct by visiting: https://forums.adobe.com/message/7132586#7132586 and clicking ‘Correct’ below the answer
     Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page:
Please note that the Adobe Forums do not accept email attachments. If you want to embed an image in your message please visit the thread in the forum and click the camera icon: https://forums.adobe.com/message/7132586#7132586
     To unsubscribe from this thread, please visit the message page at , click "Following" at the top right, & "Stop Following"
     Start a new discussion in Creating, Editing & Exporting PDFs by email or at Adobe Community
For more information about maintaining your forum email notifications please go to https://forums.adobe.com/thread/1516624.

HT3209 every time i try to buy anything an error box pops up that says my apple ID has expired and i try making a new one but it keeps telling me the same thing. what do i do?

every time i try to buy anything an error box pops up that says my apple ID has expired and i try making a new one but it keeps telling me the same thing. i cant find an answer to my problem no mater what i do.

Contact iTunes Customer Service and request assistance
Use this Link > Apple Support iTunes Store Contact

I have 2 apple ID one for Egypt and other for USA , now I try to update the software but I get a message said that this software download with other ID, then I logout and sign with second ID but i got the same message again ... Now I can not sign in more

I have 2 apple ID one for Egypt and other for USA , now I try to update the software but I get a message said that this software download with other ID, then I logout and sign with second ID but i got the same message again ... Now I can not sign in more
Any solution ?
I'm using iOS 6.1.2 IPad 3
Regards

I have also noticed the same "problem". I do not fully understand the impact of using the same ID on multiple computers and devices if I want to keep them all in sync.

After a month of using CS6 Master, Acrobat ceased functioning. Many other customers with the same problem suggested deactivating Flash Pro to reactivate Acrobat. After following these instructions, the entire suite was deactivated and now dipalys a messag

After a month of using CS6 Master, Acrobat ceased functioning. Many other customers with the same problem suggested deactivating Flash Pro to reactivate Acrobat. After following these instructions, the entire suite was deactivated and now dipalys a message that our trial that will expire in 10 days (in the middle of an upcoming charity event). Is there any way to reactivate CS6? Is the only option to delete all CS programs? Can we download CS6 again with the same product key?

In general theory, one now has the Edit button for their posts, until someone/anyone Replies to it. I've had Edit available for weeks, as opposed to the old forum's ~ 30 mins.
That, however, is in theory. I've posted, and immediately seen something that needed editing, only to find NO Replies, yet the Edit button is no longer available, only seconds later. Still, in that same thread, I'd have the Edit button from older posts, to which there had also been no Replies even after several days/weeks. Found one that had to be over a month old, and Edit was still there.
Do not know the why/how of this behavior. At first, I thought that maybe there WAS a Reply, that "ate" my Edit button, but had not Refreshed on my screen. Refresh still showed no Replies, just no Edit either. In those cases, I just Reply and mention the [Edit].
Also, it seems that the buttons get very scrambled at times, and Refresh does not always clear that up. I end up clicking where I "think" the right button should be and hope for the best. Seems that when the buttons do bunch up they can appear at random around the page, often three atop one another, and maybe one way the heck out in left-field.
While I'm on a role, it would be nice to be able to switch between Flattened and Threaded Views on the fly. Each has a use, and having to go to Options and then come back down to the thread is a very slow process. Jive is probably incapable of this, but I can dream.
Hunt

I don't have a wireless printer, and want to print things off of my iPad. I know that I can use the iPad Camera Connection kit to connect USB devices like keyboards and I am wondering if I could do the same with a USB printer.

I don't have a wireless printer, and want to print things off of my iPad. I know that I can use the iPad Camera Connection kit to connect USB devices like keyboards and I am wondering if I could do the same with a USB printer.

I don't think you can connect a printer since you won't have the printer drivers. I use FingerPrint from collobos.com to print to my non-AirPrint printers.

How to display or generate PDF417 barcode dynamically in PDF form? I am using Acrobat XI Professional and there is a Bar Code Field in the same through which I generated the same. But I want to generate the same dynamically.

How to display or generate PDF417 barcode dynamically in PDF form? I am using Acrobat XI Professional and there is a Bar Code Field in the same through which I generated the same. But I want to generate the same dynamically.

What do you mean by dynamically? When yo set up a 2D bar code field you specify which field name/value pairs you want to include, along with other parameters. But be aware that they won't work with Reader unless you Reader-enable the document with LiveCycle Reader Extensions and include the bar code usage right. It will work with Acrobat Standard/Pro.

I started with one itunes account for my iphone and ipad, and now have a second ipad linked to the same itunes. Can I set up a new itunes account for one ipad without losing what has already been downloaded on it?

I started with one itunes account for my iphone and ipad, and now have a second ipad linked to the same itunes. Can I set up a new itunes account for one ipad without losing what has already been downloaded on it? I want to stop my husbands downloads appearing on my ipad, and vice versa.

A much simpler solution would be to go into Settings > Store and turn off Automatic Downloads

Can I sync certain itmes from one itunes account and certain items from another itunes account on the same ipad?

I was wondering if an individual would be able to sync certain items from one itunes account and and items from a different itunes account to the same ipad?

You move the song files to /Users/Shared/ and then into iTunes from the other Mac OS X user account.
If you want to change the iTunes Store account associated with them, you need to redownload them from that account.
(60812)

I purchased Adobe photoshop elements II and Adobe premiere elements II. They are both on one disc. My computer crasded and I had to reload Windows. I only have one serial number and it only works with photoshop II. The same serial number will not work for

I purchased Adobe photoshop elements II and Adobe premiere elements II. They are both on one disc. My computer crasded and I had to reload Windows. I only have one serial number and it only works with photoshop II. The same serial number will not work for Premiere. I dont have any other serial numbers. What do I do???

Static_Unit
I am getting a bit concerned about what is happening in your situation. Yesterday you posted your question in at least two different forums, one of them being here in the Premiere Elements Forum.
Don't Have Serial Number for Premiere, Only Photoshop?
Wherever you posted, the reply was to contact Adobe via its Adobe Chat. It is the only one who can sort out this matter for you.
In the thread cited above I offered to help you with the difficulties that you were having visualizing the Adobe Chat in its web page. I was waiting for your follow up on that in the above thread. Instead, I find your same question in a new Adobe Premiere Elements Forum thread this afternoon with no refer the prior threads or prior recommendations given you.
I will also mention again...when you buy the Photoshop Elements and Premiere Elements bundled in one packaging and with installation files for each on the same installation disc, each program has its own serial number. The Photoshop Elements serial number does not work for Premiere Elements and vice versa. The serial numbers are on labels on a box which houses the installation disc envelope(s). So, if you purchased both programs and found the Photoshop Elements serial number, then the Premiere Elements serial number should be in a label right underneath the label with the serial number for Photoshop Elements. I recall writing this in your yesterday's thread on this matter.
The moderator will no doubt be along shortly to close or delete this thread. So, just in case, please bookmark your yesterday's thread cited above so that we can continue this communication which is trying to help you.
Thanks.
ATR

Using 802.1x and 2 hosts (one physical and one virtual) on the same port

Similar Messages

Maybe you are looking for